diff --git a/Firmware/Marlin_main.cpp b/Firmware/Marlin_main.cpp
index 6aea1214..4966caa1 100644
--- a/Firmware/Marlin_main.cpp
+++ b/Firmware/Marlin_main.cpp
@@ -1663,7 +1663,7 @@ void setup()
 	  }
 	  else if (calibration_status() == CALIBRATION_STATUS_Z_CALIBRATION) {
 		  // Show the message.
-		  lcd_show_fullscreen_message_and_wait_P(_T(MSG_FOLLOW_CALIBRATION_FLOW));
+		  lcd_show_fullscreen_message_and_wait_P(_T(MSG_FOLLOW_Z_CALIBRATION_FLOW));
 	  }
   }
 
@@ -3140,11 +3140,6 @@ void gcode_M600(bool automatic, float x_position, float y_position, float z_shif
       plan_buffer_line(lastpos[X_AXIS], lastpos[Y_AXIS], lastpos[Z_AXIS], current_position[E_AXIS], FILAMENTCHANGE_ZFEED, active_extruder);
       st_synchronize();  
       
-	  //Unretract
-      current_position[E_AXIS]= current_position[E_AXIS] - e_shift;
-      plan_buffer_line(lastpos[X_AXIS], lastpos[Y_AXIS], lastpos[Z_AXIS], current_position[E_AXIS], FILAMENTCHANGE_RFEED, active_extruder);
-	  st_synchronize();
-
       //Set E position to original  
       plan_set_e_position(lastpos[E_AXIS]);
 
diff --git a/Firmware/messages.c b/Firmware/messages.c
index 857c05c5..35aa9068 100644
--- a/Firmware/messages.c
+++ b/Firmware/messages.c
@@ -43,6 +43,7 @@ const char MSG_FIND_BED_OFFSET_AND_SKEW_LINE1[] PROGMEM_I1 = ISTR("Searching bed
 const char MSG_FIND_BED_OFFSET_AND_SKEW_LINE2[] PROGMEM_I1 = ISTR(" of 4"); ////c=14 r=0
 const char MSG_FINISHING_MOVEMENTS[] PROGMEM_I1 = ISTR("Finishing movements"); ////c=20 r=1
 const char MSG_FOLLOW_CALIBRATION_FLOW[] PROGMEM_I1 = ISTR("Printer has not been calibrated yet. Please follow the manual, chapter First steps, section Calibration flow."); ////c=20 r=8
+const char MSG_FOLLOW_Z_CALIBRATION_FLOW[] PROGMEM_I1 = ISTR("There is still a need to make Z calibration. Please follow the manual, chapter First steps, section Calibration flow."); ////c=20 r=8
 const char MSG_FSENS_AUTOLOAD_NA[] PROGMEM_I1 = ISTR("F. autoload [N/A]"); ////c=17 r=1
 const char MSG_FSENSOR_OFF[] PROGMEM_I1 = ISTR("Fil. sensor [off]"); ////c=0 r=0
 const char MSG_FSENSOR_ON[] PROGMEM_I1 = ISTR("Fil. sensor  [on]"); ////c=0 r=0
diff --git a/Firmware/messages.h b/Firmware/messages.h
index 95a1610f..07f2a3a7 100644
--- a/Firmware/messages.h
+++ b/Firmware/messages.h
@@ -40,6 +40,7 @@ extern const char MSG_FIND_BED_OFFSET_AND_SKEW_LINE1[];
 extern const char MSG_FIND_BED_OFFSET_AND_SKEW_LINE2[];
 extern const char MSG_FINISHING_MOVEMENTS[];
 extern const char MSG_FOLLOW_CALIBRATION_FLOW[];
+extern const char MSG_FOLLOW_Z_CALIBRATION_FLOW[];
 extern const char MSG_FSENS_AUTOLOAD_NA[];
 extern const char MSG_FSENSOR_OFF[];
 extern const char MSG_FSENSOR_ON[];