diff --git a/Firmware/planner.cpp b/Firmware/planner.cpp
index 078abac4..0d0f3e36 100644
--- a/Firmware/planner.cpp
+++ b/Firmware/planner.cpp
@@ -1019,21 +1019,23 @@ Having the real displacement of the head, we can calculate the total movement le
     /**
      * Use LIN_ADVANCE for blocks if all these are true:
      *
-     * block->steps_e        : This is a print move, because we checked for X, Y, Z steps before.
-     * extruder_advance_K    : There is an advance factor set.
-     * delta_mm[E_AXIS] > 0  : Extruder is running forward (e.g., for "Wipe while retracting" (Slic3r) or "Combing" (Cura) moves)
+     * block->steps_e       : This is a print move, because we checked for X, Y, Z steps before.
+     * extruder_advance_K   : There is an advance factor set.
+     * delta_mm[E_AXIS] > 0 : Extruder is running forward (e.g., for "Wipe while retracting" (Slic3r) or "Combing" (Cura) moves)
      */
-    block->use_advance_lead =  block->steps_e.wide
-                               && extruder_advance_K
-                               && delta_mm[E_AXIS] > 0;
+    block->use_advance_lead = block->steps_e.wide
+                              && extruder_advance_K
+                              && delta_mm[E_AXIS] > 0;
     if (block->use_advance_lead) {
         block->e_D_ratio = (e - position_float[E_AXIS]) /
                            sqrt(sq(x - position_float[X_AXIS])
                                 + sq(y - position_float[Y_AXIS])
                                 + sq(z - position_float[Z_AXIS]));
 
-        // Check for unusual high e_D ratio to detect if a retract move was combined with the last print move due to min. steps per segment. Never execute this with advance!
-        // This assumes no one will use a retract length of 0mm < retr_length < ~0.2mm and no one will print 100mm wide lines using 3mm filament or 35mm wide lines using 1.75mm filament.
+        // Check for unusual high e_D ratio to detect if a retract move was combined with the last
+        // print move due to min. steps per segment. Never execute this with advance! This assumes
+        // no one will use a retract length of 0mm < retr_length < ~0.2mm and no one will print
+        // 100mm wide lines using 3mm filament or 35mm wide lines using 1.75mm filament.
         if (block->e_D_ratio > 3.0)
             block->use_advance_lead = false;
         else {
diff --git a/Firmware/planner.h b/Firmware/planner.h
index 56e1c66c..44c57ea5 100644
--- a/Firmware/planner.h
+++ b/Firmware/planner.h
@@ -110,10 +110,10 @@ typedef struct {
 
   // Pre-calculated division for the calculate_trapezoid_for_block() routine to run faster.
   float speed_factor;
-    
+
 #ifdef LIN_ADVANCE
   bool use_advance_lead;            // Whether the current block uses LA
-  uint16_t advance_rate,           // Step-rate for extruder speed
+  uint16_t advance_rate,            // Step-rate for extruder speed
            max_adv_steps,           // max. advance steps to get cruising speed pressure (not always nominal_speed!)
            final_adv_steps;         // advance steps due to exit speed
   uint8_t advance_step_loops;       // Number of stepper ticks for each advance isr