Automatic recovery typo fix

Failures statistics in eeprom

Firmware/Configuration.h

@@ -64,6 +64,12 @@
 #define EEPROM_CRASH_DET       (EEPROM_UVLO_MESH_BED_LEVELING-12) 
 // Filament sensor on/off EEPROM setting 
 #define EEPROM_FSENSOR       (EEPROM_UVLO_MESH_BED_LEVELING-14) 
+// Crash detection counter
+#define EEPROM_CRASH_COUNT       (EEPROM_UVLO_MESH_BED_LEVELING-15)
+// Filament runout/error coutner
+#define EEPROM_FERROR_COUNT      (EEPROM_UVLO_MESH_BED_LEVELING-16)
+// Power loss errors
+#define EEPROM_POWER_COUNT       (EEPROM_UVLO_MESH_BED_LEVELING-17)
 
 // Currently running firmware, each digit stored as uint16_t.
 // The flavor differentiates a dev, alpha, beta, release candidate or a release version.

Firmware/Marlin_main.cpp

@@ -712,6 +712,12 @@ void fsensor_update()
 		{
 			MYSERIAL.println("fsensor_update - ERROR!!!");
 			fsensor_stop_and_save_print();
+            
+            // Increment filament failure counter
+            uint8_t ferror_count = eeprom_read_byte((uint8_t*)EEPROM_FERROR_COUNT);
+            ferror_count++;
+            eeprom_update_byte((uint8_t*)EEPROM_FERROR_COUNT, ferror_count);
+            
 			enquecommand_front_P((PSTR("M600")));
 			fsensor_M600 = true;
 			fsensor_enabled = false;
@@ -5830,6 +5836,11 @@ case 404:  //M404 Enter the nominal filament width (3mm, 1.75mm ) N<3.0> or disp
 	case 10: // D10 - Tell the printer that XYZ calibration went OK
         calibration_status_store(CALIBRATION_STATUS_LIVE_ADJUST); 
         break;
+    
+    case 12: //D12 - Reset Filament error, Power loss and crash counter ( Do it before every print and you can get stats for the print )
+        eeprom_update_byte((uint8_t*)EEPROM_CRASH_COUNT, 0x00);
+        eeprom_update_byte((uint8_t*)EEPROM_FERROR_COUNT, 0x00);
+        eeprom_update_byte((uint8_t*)EEPROM_POWER_COUNT, 0x00);
 	case 999:
 	{
 		MYSERIAL.println("D999 - crash");
@@ -5844,6 +5855,12 @@ case 404:  //M404 Enter the nominal filament width (3mm, 1.75mm ) N<3.0> or disp
 		lcd_update_enable(true);
 		lcd_implementation_clear();
 		lcd_update(2);
+        
+        // Increment crash counter
+        uint8_t crash_count = eeprom_read_byte((uint8_t*)EEPROM_CRASH_COUNT);
+        crash_count++;
+        eeprom_update_byte((uint8_t*)EEPROM_CRASH_COUNT, crash_count);
+        
 #ifdef AUTOMATIC_RECOVERY_AFTER_CRASH
         bool yesno = true;
 #else
@@ -7072,6 +7089,11 @@ void uvlo_()
 #endif
     disable_z();
     
+    // Increment power failure counter
+    uint8_t power_count = eeprom_read_byte((uint8_t*)EEPROM_POWER_COUNT);
+    power_count++;
+    eeprom_update_byte((uint8_t*)EEPROM_POWER_COUNT, power_count);
+    
 		SERIAL_ECHOLNPGM("UVLO - end");
 		cli();
 		while(1);

Firmware/ultralcd.cpp

@@ -189,6 +189,8 @@ static void prusa_stat_temperatures();
 static void prusa_stat_printinfo();
 static void lcd_farm_no();
 static void lcd_menu_extruder_info();
+static void lcd_menu_fails_stats();
+
 #ifdef DOGLCD
 static void lcd_set_contrast();
 #endif
@@ -961,6 +963,47 @@ static void lcd_menu_extruder_info()
     }
 }
 
+static void lcd_menu_fails_stats()
+{
+    
+    // Display screen info
+    
+    lcd.setCursor(0, 0);
+    lcd.print("Failure stats       ");
+    
+    // Display power failures
+    uint8_t power_count = eeprom_read_byte((uint8_t*)EEPROM_POWER_COUNT);
+    lcd.setCursor(0, 1);
+    lcd.print(" Power failures:    ");
+    lcd.setCursor(17, 1);
+    lcd.print(itostr3((int)power_count));
+
+    
+    // Display Crash detected
+    uint8_t crash_count = eeprom_read_byte((uint8_t*)EEPROM_CRASH_COUNT);
+    lcd.setCursor(0, 2);
+    lcd.print(" Crash detected:    ");
+    lcd.setCursor(17, 2);
+    lcd.print(itostr3((int)crash_count));
+    
+    
+    // Display filament failures
+    uint8_t ferror_count = eeprom_read_byte((uint8_t*)EEPROM_FERROR_COUNT);
+    lcd.setCursor(0, 3);
+    lcd.print(" Filament fails:    ");
+    lcd.setCursor(17, 3);
+    lcd.print(itostr3((int)ferror_count));
+    
+
+    
+    if (lcd_clicked())
+    {
+        lcd_quick_feedback();
+        lcd_return_to_status();
+    }
+    
+}
+
 static void lcd_menu_temperatures()
 {
     lcd.setCursor(1, 1);
@@ -1066,6 +1109,9 @@ static void lcd_support_menu()
   MENU_ITEM(function, PSTR("XYZ cal. details"), lcd_service_mode_show_result);
     }
   MENU_ITEM(submenu, MSG_INFO_EXTRUDER, lcd_menu_extruder_info);
+    
+  MENU_ITEM(submenu, PSTR("Fail stats"), lcd_menu_fails_stats);
+    
   MENU_ITEM(submenu, PSTR("Temperatures"), lcd_menu_temperatures);
   if (fans_check_enabled == true) {
 	  MENU_ITEM(function, PSTR("Check fans [EN]"), lcd_set_fan_check);
@@ -1077,7 +1123,7 @@ static void lcd_support_menu()
     
 #ifdef AUTOMATIC_RECOVERY_AFTER_CRASH
     MENU_ITEM(back, PSTR("Auto recover crash"), lcd_main_menu);
-#else
+#endif
   END_MENU();
 }