Merge pull request #2568 from 3d-gussner/MK3_Dcodes_move

D- codes move

Firmware/Dcodes.cpp

@@ -635,6 +635,98 @@ void dcode_12()
 
 }
 
+#ifdef HEATBED_ANALYSIS
+    /*!
+    ### D80 - Bed check <a href="https://reprap.org/wiki/G-code#D80:_Bed_check">D80: Bed check</a>
+    This command will log data to SD card file "mesh.txt".
+    #### Usage
+    
+        D80 [ E | F | G | H | I | J ]
+    
+    #### Parameters
+    - `E` - Dimension X (default 40)
+    - `F` - Dimention Y (default 40)
+    - `G` - Points X (default 40)
+    - `H` - Points Y (default 40)
+    - `I` - Offset X (default 74)
+    - `J` - Offset Y (default 34)
+  */
+void dcode_80()
+{
+	float dimension_x = 40;
+	float dimension_y = 40;
+	int points_x = 40;
+	int points_y = 40;
+	float offset_x = 74;
+	float offset_y = 33;
+
+	if (code_seen('E')) dimension_x = code_value();
+	if (code_seen('F')) dimension_y = code_value();
+	if (code_seen('G')) {points_x = code_value(); }
+	if (code_seen('H')) {points_y = code_value(); }
+	if (code_seen('I')) {offset_x = code_value(); }
+	if (code_seen('J')) {offset_y = code_value(); }
+	printf_P(PSTR("DIM X: %f\n"), dimension_x);
+	printf_P(PSTR("DIM Y: %f\n"), dimension_y);
+	printf_P(PSTR("POINTS X: %d\n"), points_x);
+	printf_P(PSTR("POINTS Y: %d\n"), points_y);
+	printf_P(PSTR("OFFSET X: %f\n"), offset_x);
+	printf_P(PSTR("OFFSET Y: %f\n"), offset_y);
+		bed_check(dimension_x,dimension_y,points_x,points_y,offset_x,offset_y);
+}
+
+
+    /*!
+    ### D81 - Bed analysis <a href="https://reprap.org/wiki/G-code#D81:_Bed_analysis">D80: Bed analysis</a>
+    This command will log data to SD card file "wldsd.txt".
+    #### Usage
+    
+        D81 [ E | F | G | H | I | J ]
+    
+    #### Parameters
+    - `E` - Dimension X (default 40)
+    - `F` - Dimention Y (default 40)
+    - `G` - Points X (default 40)
+    - `H` - Points Y (default 40)
+    - `I` - Offset X (default 74)
+    - `J` - Offset Y (default 34)
+  */
+void dcode_81()
+{
+	float dimension_x = 40;
+	float dimension_y = 40;
+	int points_x = 40;
+	int points_y = 40;
+	float offset_x = 74;
+	float offset_y = 33;
+
+	if (code_seen('E')) dimension_x = code_value();
+	if (code_seen('F')) dimension_y = code_value();
+	if (code_seen("G")) { strchr_pointer+=1; points_x = code_value(); }
+	if (code_seen("H")) { strchr_pointer+=1; points_y = code_value(); }
+	if (code_seen("I")) { strchr_pointer+=1; offset_x = code_value(); }
+	if (code_seen("J")) { strchr_pointer+=1; offset_y = code_value(); }
+	
+	bed_analysis(dimension_x,dimension_y,points_x,points_y,offset_x,offset_y);
+	
+}
+
+#endif //HEATBED_ANALYSIS
+
+    /*!
+    ### D106 - Print measured fan speed for different pwm values <a href="https://reprap.org/wiki/G-code#D106:_Print_measured_fan_speed_for_different_pwm_values">D106: Print measured fan speed for different pwm values</a>
+    */
+void dcode_106()
+{
+	for (int i = 255; i > 0; i = i - 5) {
+		fanSpeed = i;
+		//delay_keep_alive(2000);
+		for (int j = 0; j < 100; j++) {
+			delay_keep_alive(100);
+			}
+			printf_P(_N("%d: %d\n"), i, fan_speed[1]);
+	}
+}
 
 #ifdef TMC2130
 #include "planner.h"

Firmware/Dcodes.h

@@ -2,26 +2,40 @@
 #define DCODES_H
 
 extern void dcode__1(); //D-1 - Endless loop (to simulate deadlock)
-
 extern void dcode_0(); //D0 - Reset
 extern void dcode_1(); //D1 - Clear EEPROM
 extern void dcode_2(); //D2 - Read/Write RAM
+
+#ifdef DEBUG_DCODE3
 extern void dcode_3(); //D3 - Read/Write EEPROM
+#endif //DEBUG_DCODE3
+
 extern void dcode_4(); //D4 - Read/Write PIN
+
+#ifdef DEBUG_DCODE5
 extern void dcode_5(); //D5 - Read/Write FLASH
+#endif //DEBUG_DCODE5
+
 extern void dcode_6(); //D6 - Read/Write external FLASH
 extern void dcode_7(); //D7 - Read/Write Bootloader
 extern void dcode_8(); //D8 - Read/Write PINDA
 extern void dcode_9(); //D9 - Read/Write ADC (Write=enable simulated, Read=disable simulated)
-
 extern void dcode_10(); //D10 - XYZ calibration = OK
+extern void dcode_12(); //D12 - Log time. Writes the current time in the log file.
+
+#ifdef HEATBED_ANALYSIS
+extern void dcode_80(); //D80 - Bed check. This command will log data to SD card file "mesh.txt".
+extern void dcode_81(); //D81 - Bed analysis. This command will log data to SD card file "wldsd.txt".
+#endif //HEATBED_ANALYSIS
+
+	extern void dcode_106(); //D106 - Print measured fan speed for different pwm values
 
 #ifdef TMC2130
-extern void dcode_2130(); //D2130 - TMC2130
+	extern void dcode_2130(); //D2130 - TMC2130
 #endif //TMC2130
 
 #ifdef PAT9125
-extern void dcode_9125(); //D9125 - PAT9125
+	extern void dcode_9125(); //D9125 - PAT9125
 #endif //PAT9125
 
 

Firmware/Marlin_main.cpp

@@ -8984,28 +8984,7 @@ Sigma_Exit:
     - `J` - Offset Y (default 34)
   */
 	case 80:
-	{
+		dcode_80(); break;
-		float dimension_x = 40;
-		float dimension_y = 40;
-		int points_x = 40;
-		int points_y = 40;
-		float offset_x = 74;
-		float offset_y = 33;
-
-		if (code_seen('E')) dimension_x = code_value();
-		if (code_seen('F')) dimension_y = code_value();
-		if (code_seen('G')) {points_x = code_value(); }
-		if (code_seen('H')) {points_y = code_value(); }
-		if (code_seen('I')) {offset_x = code_value(); }
-		if (code_seen('J')) {offset_y = code_value(); }
-		printf_P(PSTR("DIM X: %f\n"), dimension_x);
-		printf_P(PSTR("DIM Y: %f\n"), dimension_y);
-		printf_P(PSTR("POINTS X: %d\n"), points_x);
-		printf_P(PSTR("POINTS Y: %d\n"), points_y);
-		printf_P(PSTR("OFFSET X: %f\n"), offset_x);
-		printf_P(PSTR("OFFSET Y: %f\n"), offset_y);
- 		bed_check(dimension_x,dimension_y,points_x,points_y,offset_x,offset_y);
-	}break;
 
     /*!
     ### D81 - Bed analysis <a href="https://reprap.org/wiki/G-code#D81:_Bed_analysis">D80: Bed analysis</a>
@@ -9023,24 +9002,7 @@ Sigma_Exit:
     - `J` - Offset Y (default 34)
   */
 	case 81:
-	{
+		dcode_81(); break;
-		float dimension_x = 40;
-		float dimension_y = 40;
-		int points_x = 40;
-		int points_y = 40;
-		float offset_x = 74;
-		float offset_y = 33;
-
-		if (code_seen('E')) dimension_x = code_value();
-		if (code_seen('F')) dimension_y = code_value();
-		if (code_seen("G")) { strchr_pointer+=1; points_x = code_value(); }
-		if (code_seen("H")) { strchr_pointer+=1; points_y = code_value(); }
-		if (code_seen("I")) { strchr_pointer+=1; offset_x = code_value(); }
-		if (code_seen("J")) { strchr_pointer+=1; offset_y = code_value(); }
-		
-		bed_analysis(dimension_x,dimension_y,points_x,points_y,offset_x,offset_y);
-		
-	} break;
 	
 #endif //HEATBED_ANALYSIS
 #ifdef DEBUG_DCODES
@@ -9049,17 +9011,7 @@ Sigma_Exit:
     ### D106 - Print measured fan speed for different pwm values <a href="https://reprap.org/wiki/G-code#D106:_Print_measured_fan_speed_for_different_pwm_values">D106: Print measured fan speed for different pwm values</a>
     */
 	case 106:
-	{
+		dcode_106(); break;
-		for (int i = 255; i > 0; i = i - 5) {
-			fanSpeed = i;
-			//delay_keep_alive(2000);
-			for (int j = 0; j < 100; j++) {
-				delay_keep_alive(100);
-
-			}
-			printf_P(_N("%d: %d\n"), i, fan_speed[1]);
-		}
-	}break;
 
 #ifdef TMC2130
     /*!