diff --git a/Firmware/pins_Einy_0_3.h b/Firmware/pins_Einy_0_3.h deleted file mode 100644 index 936e8d0e..00000000 --- a/Firmware/pins_Einy_0_3.h +++ /dev/null @@ -1,129 +0,0 @@ -/***************************************************************** -* EINY Rambo 0.3a Pin Assignments -******************************************************************/ - -#define ELECTRONICS "EINY_03a" - -#define KNOWN_BOARD -#ifndef __AVR_ATmega2560__ - #error Oops! Make sure you have 'Arduino Mega 2560 or Rambo' selected from the 'Tools -> Boards' menu. -#endif - -#define TMC2130 -#define PAT9125 - -#define SWI2C // enable software i2c -#define SWI2C_A8 // 8bit address functions - -#define PAT9125_SWI2C -#define PAT9125_SWI2C_SDA 20 //SDA on P3 -#define PAT9125_SWI2C_SCL 21 //SCL on P3 -#define PAT9125_SWI2C_CFG 0xb1 //2us clock delay, 2048 cycles timeout - -//#define SWSPI_MISO 16 //RX2 -//#define SWSPI_MOSI 16 //RX2 -//#define SWSPI_SCK 17 //TX2 -//#define SWSPI_CS 20 //SDA - -////#define SWI2C_SDA 20 //SDA -////#define SWI2C_SCL 21 //SCL -//#define SWI2C_SDA 16 //RX2 -//#define SWI2C_SCL 17 //TX2 - -#define X_TMC2130_CS 41 -#define X_TMC2130_DIAG 40 -#define X_STEP_PIN 37 -#define X_DIR_PIN 49 -//#define X_MIN_PIN 12 -//#define X_MAX_PIN 30 -#define X_MIN_PIN X_TMC2130_DIAG -#define X_MAX_PIN X_TMC2130_DIAG -#define X_ENABLE_PIN 29 -#define X_MS1_PIN -1 -#define X_MS2_PIN -1 - -#define Y_TMC2130_CS 39 -#define Y_TMC2130_DIAG 69 -#define Y_STEP_PIN 36 -#define Y_DIR_PIN 48 -//#define Y_MIN_PIN 11 -//#define Y_MAX_PIN 24 -#define Y_MIN_PIN Y_TMC2130_DIAG -#define Y_MAX_PIN Y_TMC2130_DIAG -#define Y_ENABLE_PIN 28 -#define Y_MS1_PIN -1 -#define Y_MS2_PIN -1 - -#define Z_TMC2130_CS 67 -#define Z_TMC2130_DIAG 68 -#define Z_STEP_PIN 35 -#define Z_DIR_PIN 47 -#define Z_MIN_PIN 10 -#define Z_MAX_PIN 23 -//#define Z_MAX_PIN Z_TMC2130_DIAG -#define Z_ENABLE_PIN 27 -#define Z_MS1_PIN -1 -#define Z_MS2_PIN -1 - -#define HEATER_BED_PIN 4 //PG5 -#define TEMP_BED_PIN 2 //A2 - -#define HEATER_0_PIN 3 //PE5 -#define TEMP_0_PIN 0 //A0 - -#define HEATER_1_PIN -1 -#define TEMP_1_PIN 1 //A1 - -#define HEATER_2_PIN -1 -#define TEMP_2_PIN -1 - -#define TEMP_AMBIENT_PIN 6 //A6 - -#define TEMP_PINDA_PIN 3 //A3 - -#define E0_TMC2130_CS 66 -#define E0_TMC2130_DIAG 65 -#define E0_STEP_PIN 34 -#define E0_DIR_PIN 43 -#define E0_ENABLE_PIN 26 -#define E0_MS1_PIN -1 -#define E0_MS2_PIN -1 - -#define MOTOR_CURRENT_PWM_XY_PIN 46 -#define MOTOR_CURRENT_PWM_Z_PIN 45 -#define MOTOR_CURRENT_PWM_E_PIN 44 -#define SDPOWER -1 -#define SDSS 53 -#define LED_PIN 13 -#define FAN_PIN 6 -#define FAN_1_PIN -1 -#define PS_ON_PIN -1 -#define KILL_PIN -1 // 80 with Smart Controller LCD -#define SUICIDE_PIN -1 // PIN that has to be turned on right after start, to keep power flowing. - -#ifdef ULTRA_LCD - -//#define KILL_PIN 32 - -#ifdef NEWPANEL - -#define BEEPER 84 // Beeper on AUX-4 -#define LCD_PINS_RS 82 -#define LCD_PINS_ENABLE 18 -#define LCD_PINS_D4 19 -#define LCD_PINS_D5 70 -#define LCD_PINS_D6 85 -#define LCD_PINS_D7 71 - -//buttons are directly attached using AUX-2 -#define BTN_EN1 72 -#define BTN_EN2 14 -#define BTN_ENC 9 // the click - -#define SDCARDDETECT 15 - -#define TACH_0 81 -#define TACH_1 80 - -#endif //NEWPANEL -#endif //ULTRA_LCD diff --git a/Firmware/pins_Rambo.h b/Firmware/pins_Rambo.h deleted file mode 100644 index 4ba00d1a..00000000 --- a/Firmware/pins_Rambo.h +++ /dev/null @@ -1,162 +0,0 @@ -/***************************************************************** -* Rambo Pin Assignments -******************************************************************/ - -#define ELECTRONICS "RAMBoBig" - -#define KNOWN_BOARD -#ifndef __AVR_ATmega2560__ - #error Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu. -#endif - -#define FR_SENS 21 - -#define X_STEP_PIN 37 -#define X_DIR_PIN 48 -#define X_MIN_PIN 12 -#define X_MAX_PIN 30 -#define X_ENABLE_PIN 29 -#define X_MS1_PIN 40 -#define X_MS2_PIN 41 -#define Y_STEP_PIN 36 -#define Y_DIR_PIN 49 -#define Y_MIN_PIN 11 -#define Y_MAX_PIN 24 -#define Y_ENABLE_PIN 28 -#define Y_MS1_PIN 69 -#define Y_MS2_PIN 39 -#define Z_STEP_PIN 35 -#define Z_DIR_PIN 47 -#define Z_MIN_PIN 10 -#define Z_MAX_PIN 23 -#define Z_ENABLE_PIN 27 -#define Z_MS1_PIN 68 -#define Z_MS2_PIN 67 -#define TEMP_BED_PIN 2 -#define TEMP_0_PIN 0 -#define HEATER_1_PIN 7 -#define TEMP_1_PIN 1 -#define TEMP_2_PIN -1 - -#ifdef SNMM - #define E_MUX0_PIN 17 - #define E_MUX1_PIN 16 - #define E_MUX2_PIN 84 -#endif - -#ifdef DIS - #define D_REQUIRE 30 - #define D_DATA 20 - #define D_DATACLOCK 21 -#endif - -// The SDSS pin uses a different pin mapping from file Sd2PinMap.h -#define SDSS 53 - -#ifndef SDSUPPORT -// these pins are defined in the SD library if building with SD support - #define SCK_PIN 52 - #define MISO_PIN 50 - #define MOSI_PIN 51 -#endif - -#define BEEPER 84 - -#define BTN_EN1 72 -#define BTN_EN2 14 -#define BTN_ENC 9 - -#define SDCARDDETECT 15 - -#define LCD_PINS_RS 82 -#define LCD_PINS_ENABLE 18 -#define LCD_PINS_D4 19 -#define LCD_PINS_D5 70 -#define LCD_PINS_D6 85 -#define LCD_PINS_D7 71 - -#define E0_STEP_PIN 34 -#define E0_DIR_PIN 43 -#define E0_ENABLE_PIN 26 -#define E0_MS1_PIN 65 -#define E0_MS2_PIN 66 -#define LED_PIN 13 - -#ifdef THREEMM_PRINTER - #define FAN_PIN 8 -#else - #define FAN_PIN 6 -#endif - -#define KILL_PIN -1 //80 with Smart Controller LCD -#define SUICIDE_PIN -1 //PIN that has to be turned on right after start, to keep power flowing. -#define SDPOWER -1 -#define HEATER_2_PIN -1 - -#define E1_STEP_PIN 33 -#define E1_DIR_PIN 42 -#define E1_ENABLE_PIN 25 -#define E1_MS1_PIN 63 -#define E1_MS2_PIN 64 -#define DIGIPOTSS_PIN 38 -#define DIGIPOT_CHANNELS {4,5,3,0,1} // X Y Z E0 E1 digipot channels to stepper driver mapping -#define HEATER_0_PIN 9 -#define HEATER_BED_PIN 3 -#define PS_ON_PIN 4 -#define SDSS 53 -#ifdef ULTRA_LCD - #define KILL_PIN 80 - #ifdef NEWPANEL - //arduino pin which triggers an piezzo beeper - #define BEEPER 84 // Beeper on AUX-4 - #define LCD_PINS_RS 82 - #define LCD_PINS_ENABLE 18 - #define LCD_PINS_D4 19 - #define LCD_PINS_D5 70 - #define LCD_PINS_D6 85 - #define LCD_PINS_D7 71 - //buttons are directly attached using AUX-2 - #define BTN_EN1 76 - #define BTN_EN2 77 - #define BTN_ENC 78 //the click - #define BLEN_C 2 - #define BLEN_B 1 - #define BLEN_A 0 - #define SDCARDDETECT 81 // Ramps does not use this port - //encoder rotation values - #define encrot0 0 - #define encrot1 2 - #define encrot2 3 - #define encrot3 1 - #else //old style panel with shift register - //arduino pin witch triggers an piezzo beeper - #define BEEPER 84 //No Beeper added - //buttons are attached to a shift register - // Not wired this yet - // #define SHIFT_CLK 38 - // #define SHIFT_LD 42 - // #define SHIFT_OUT 40 - // #define SHIFT_EN 17 - #define LCD_PINS_RS 82 - #define LCD_PINS_ENABLE 18 - #define LCD_PINS_D4 19 - #define LCD_PINS_D5 70 - #define LCD_PINS_D6 85 - #define LCD_PINS_D7 71 - //encoder rotation values - #define encrot0 0 - #define encrot1 2 - #define encrot2 3 - #define encrot3 1 - //bits in the shift register that carry the buttons for: - // left up center down right red - #define BL_LE 7 - #define BL_UP 6 - #define BL_MI 5 - #define BL_DW 4 - #define BL_RI 3 - #define BL_ST 2 - #define BLEN_B 1 - #define BLEN_A 0 - #endif -#endif //ULTRA_LCD diff --git a/Firmware/pins_Rambo_1_0.h b/Firmware/pins_Rambo_1_0.h deleted file mode 100644 index fae9ddcc..00000000 --- a/Firmware/pins_Rambo_1_0.h +++ /dev/null @@ -1,94 +0,0 @@ -/***************************************************************** -* Rambo mini 1.0 Pin Assignments -******************************************************************/ - -#define ELECTRONICS "RAMBo10a" - -#define KNOWN_BOARD -#ifndef __AVR_ATmega2560__ - #error Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu. -#endif - -#define FR_SENS 21 - -#define X_STEP_PIN 37 -#define X_DIR_PIN 48 -#define X_MIN_PIN 12 -#define X_MAX_PIN 30 -#define X_ENABLE_PIN 29 -#define X_MS1_PIN 40 -#define X_MS2_PIN 41 -#define Y_STEP_PIN 36 -#define Y_DIR_PIN 49 -#define Y_MIN_PIN 11 -#define Y_MAX_PIN 24 -#define Y_ENABLE_PIN 28 -#define Y_MS1_PIN 69 -#define Y_MS2_PIN 39 -#define Z_STEP_PIN 35 -#define Z_DIR_PIN 47 -#define Z_MIN_PIN 10 -#define Z_MAX_PIN 23 -#define Z_ENABLE_PIN 27 -#define Z_MS1_PIN 68 -#define Z_MS2_PIN 67 -#define TEMP_BED_PIN 2 -#define TEMP_0_PIN 0 -#define HEATER_1_PIN 7 -#define TEMP_1_PIN 1 -#define TEMP_2_PIN -1 - -#ifdef SNMM - #define E_MUX0_PIN 17 - #define E_MUX1_PIN 16 - #define E_MUX2_PIN 84 -#endif - -// The SDSS pin uses a different pin mapping from file Sd2PinMap.h -#define SDSS 53 - -#ifndef SDSUPPORT -// these pins are defined in the SD library if building with SD support - #define SCK_PIN 52 - #define MISO_PIN 50 - #define MOSI_PIN 51 -#endif - -#define BEEPER 78 - -#define BTN_EN1 80 -#define BTN_EN2 73 -#define BTN_ENC 21 - -#define SDCARDDETECT 72 - -#define LCD_PINS_RS 38 -#define LCD_PINS_ENABLE 5 -#define LCD_PINS_D4 14 -#define LCD_PINS_D5 15 -#define LCD_PINS_D6 32 -#define LCD_PINS_D7 31 - -#define E0_STEP_PIN 34 -#define E0_DIR_PIN 43 -#define E0_ENABLE_PIN 26 -#define E0_MS1_PIN 65 -#define E0_MS2_PIN 66 -#define LED_PIN 13 -#ifdef THREEMM_PRINTER - #define FAN_PIN 8 -#else - #define FAN_PIN 6 -#endif -#define KILL_PIN -1 //80 with Smart Controller LCD -#define SUICIDE_PIN -1 //PIN that has to be turned on right after start, to keep power flowing. -#define SDPOWER -1 -#define HEATER_2_PIN -1 - -#define HEATER_0_PIN 3 -#define HEATER_BED_PIN 4 -#define FAN_1_PIN -1 //6 -#define PS_ON_PIN 71 -#define MOTOR_CURRENT_PWM_XY_PIN 46 -#define MOTOR_CURRENT_PWM_Z_PIN 45 -#define MOTOR_CURRENT_PWM_E_PIN 44 diff --git a/Firmware/pins_Rambo_1_3.h b/Firmware/pins_Rambo_1_3.h deleted file mode 100644 index 3e9c45da..00000000 --- a/Firmware/pins_Rambo_1_3.h +++ /dev/null @@ -1,102 +0,0 @@ -/***************************************************************** -* Rambo mini 1.3 Pin Assignments -******************************************************************/ - -#define ELECTRONICS "RAMBo13a" - -#define KNOWN_BOARD -#ifndef __AVR_ATmega2560__ - #error Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu. -#endif - -#define FR_SENS 21 - -#define X_STEP_PIN 37 -#define X_DIR_PIN 48 -#define X_MIN_PIN 12 -#define X_MAX_PIN 30 -#define X_ENABLE_PIN 29 -#define X_MS1_PIN 40 -#define X_MS2_PIN 41 -#define Y_STEP_PIN 36 -#define Y_DIR_PIN 49 -#define Y_MIN_PIN 11 -#define Y_MAX_PIN 24 -#define Y_ENABLE_PIN 28 -#define Y_MS1_PIN 69 -#define Y_MS2_PIN 39 -#define Z_STEP_PIN 35 -#define Z_DIR_PIN 47 -#define Z_MIN_PIN 10 -#define Z_MAX_PIN 23 -#define Z_ENABLE_PIN 27 -#define Z_MS1_PIN 68 -#define Z_MS2_PIN 67 -#define TEMP_BED_PIN 2 -#define TEMP_0_PIN 0 -#define HEATER_1_PIN 7 -#define TEMP_1_PIN 1 -#define TEMP_2_PIN -1 - -#ifdef SNMM - #define E_MUX0_PIN 17 - #define E_MUX1_PIN 16 - #define E_MUX2_PIN 84 -#endif - -#ifdef DIS - #define D_REQUIRE 30 - #define D_DATA 20 - #define D_DATACLOCK 21 -#endif - -// The SDSS pin uses a different pin mapping from file Sd2PinMap.h -#define SDSS 53 - -#ifndef SDSUPPORT -// these pins are defined in the SD library if building with SD support - #define SCK_PIN 52 - #define MISO_PIN 50 - #define MOSI_PIN 51 -#endif - -#define BEEPER 84 - -#define BTN_EN1 72 -#define BTN_EN2 14 -#define BTN_ENC 9 - -#define SDCARDDETECT 15 - -#define LCD_PINS_RS 82 -#define LCD_PINS_ENABLE 18 -#define LCD_PINS_D4 19 -#define LCD_PINS_D5 70 -#define LCD_PINS_D6 85 -#define LCD_PINS_D7 71 - -#define E0_STEP_PIN 34 -#define E0_DIR_PIN 43 -#define E0_ENABLE_PIN 26 -#define E0_MS1_PIN 65 -#define E0_MS2_PIN 66 -#define LED_PIN 13 - -#ifdef THREEMM_PRINTER - #define FAN_PIN 8 -#else - #define FAN_PIN 6 -#endif - -#define KILL_PIN -1 //80 with Smart Controller LCD -#define SUICIDE_PIN -1 //PIN that has to be turned on right after start, to keep power flowing. -#define SDPOWER -1 -#define HEATER_2_PIN -1 - -#define HEATER_0_PIN 3 -#define HEATER_BED_PIN 4 -#define FAN_1_PIN -1 //6 -#define PS_ON_PIN 71 -#define MOTOR_CURRENT_PWM_XY_PIN 46 -#define MOTOR_CURRENT_PWM_Z_PIN 45 -#define MOTOR_CURRENT_PWM_E_PIN 44 diff --git a/Firmware/variants/1_75mm-RAMBo10a-E3Dv6full.h b/Firmware/variants/1_75mm-RAMBo10a-E3Dv6full.h deleted file mode 100644 index ef288a6c..00000000 --- a/Firmware/variants/1_75mm-RAMBo10a-E3Dv6full.h +++ /dev/null @@ -1,245 +0,0 @@ -#ifndef CONFIGURATION_PRUSA_H -#define CONFIGURATION_PRUSA_H - -/*------------------------------------ - GENERAL SETTINGS -*------------------------------------*/ - -// Printer revision -#define FILAMENT_SIZE "1_75mm" -#define NOZZLE_TYPE "E3Dv6full" - -// Printer name -#define CUSTOM_MENDEL_NAME "Prusa i3" - -// Electronics -#define MOTHERBOARD BOARD_RAMBO_MINI_1_0 - - -/*------------------------------------ - AXIS SETTINGS -*------------------------------------*/ - -// Steps per unit {X,Y,Z,E} -#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/0.8,161.3} - -// Endstop inverting -const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. - -// Home position -#define MANUAL_X_HOME_POS 0 -#define MANUAL_Y_HOME_POS 0 -#define MANUAL_Z_HOME_POS 0.25 - -// Travel limits after homing -#define X_MAX_POS 214 -#define X_MIN_POS 0 -#define Y_MAX_POS 198 -#define Y_MIN_POS 0 -#define Z_MAX_POS 201 -#define Z_MIN_POS 0.23 - -// Canceled home position -#define X_CANCEL_POS 50 -#define Y_CANCEL_POS 180 - -#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E -#define HOMING_FEEDRATE {3000, 3000, 240, 0} // set the homing speeds (mm/min) - -#define DEFAULT_MAX_FEEDRATE {500, 500, 3, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,30,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts - - -#define MANUAL_FEEDRATE {3000, 3000, 240, 60} // set the speeds for manual moves (mm/min) - - -/*------------------------------------ - EXTRUDER SETTINGS -*------------------------------------*/ - -// Mintemps -#define HEATER_0_MINTEMP 15 -#define HEATER_1_MINTEMP 5 -#define HEATER_2_MINTEMP 5 -#define BED_MINTEMP 15 - -// Maxtemps -#define HEATER_0_MAXTEMP 310 -#define HEATER_1_MAXTEMP 310 -#define HEATER_2_MAXTEMP 310 -#define BED_MAXTEMP 150 - -// Define PID constants for extruder -#define DEFAULT_Kp 40.925 -#define DEFAULT_Ki 4.875 -#define DEFAULT_Kd 86.085 - -// Extrude mintemp -#define EXTRUDE_MINTEMP 130 - -// Extruder cooling fans -#define EXTRUDER_0_AUTO_FAN_PIN 8 -#define EXTRUDER_1_AUTO_FAN_PIN -1 -#define EXTRUDER_2_AUTO_FAN_PIN -1 -#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 -#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed - - - -/*------------------------------------ - LOAD/UNLOAD FILAMENT SETTINGS -*------------------------------------*/ - -// Load filament commands -#define LOAD_FILAMENT_0 "M83" -#define LOAD_FILAMENT_1 "G1 E70 F400" -#define LOAD_FILAMENT_2 "G1 E40 F100" - -// Unload filament commands -#define UNLOAD_FILAMENT_0 "M83" -#define UNLOAD_FILAMENT_1 "G1 E-80 F400" - -/*------------------------------------ - CHANGE FILAMENT SETTINGS -*------------------------------------*/ - -// Filament change configuration -#define FILAMENTCHANGEENABLE - #ifdef FILAMENTCHANGEENABLE - #define FILAMENTCHANGE_XPOS 211 - #define FILAMENTCHANGE_YPOS 0 - #define FILAMENTCHANGE_ZADD 2 - #define FILAMENTCHANGE_FIRSTRETRACT -2 - #define FILAMENTCHANGE_FINALRETRACT -80 - - #define FILAMENTCHANGE_FIRSTFEED 70 - #define FILAMENTCHANGE_FINALFEED 50 - #define FILAMENTCHANGE_RECFEED 5 - - #define FILAMENTCHANGE_XYFEED 70 - #define FILAMENTCHANGE_EFEED 20 - #define FILAMENTCHANGE_RFEED 400 - #define FILAMENTCHANGE_EXFEED 2 - #define FILAMENTCHANGE_ZFEED 300 - -#endif - -/*------------------------------------ - ADDITIONAL FEATURES SETTINGS -*------------------------------------*/ - -// Define Prusa filament runout sensor -//#define FILAMENT_RUNOUT_SUPPORT - -#ifdef FILAMENT_RUNOUT_SUPPORT - #define FILAMENT_RUNOUT_SENSOR 1 -#endif - -/*------------------------------------ - MOTOR CURRENT SETTINGS -*------------------------------------*/ - -// Motor Current setting for BIG RAMBo -#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) -#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135} - -// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range -#if MOTHERBOARD == 102 || MOTHERBOARD == 302 - #define MOTOR_CURRENT_PWM_RANGE 2000 - #define DEFAULT_PWM_MOTOR_CURRENT {270, 450, 450} // {XY,Z,E} - #define DEFAULT_PWM_MOTOR_CURRENT_LOUD {540, 450, 500} // {XY,Z,E} -#endif - -/*------------------------------------ - PREHEAT SETTINGS -*------------------------------------*/ - -#define PLA_PREHEAT_HOTEND_TEMP 210 -#define PLA_PREHEAT_HPB_TEMP 50 -#define PLA_PREHEAT_FAN_SPEED 0 - -#define ABS_PREHEAT_HOTEND_TEMP 255 -#define ABS_PREHEAT_HPB_TEMP 100 -#define ABS_PREHEAT_FAN_SPEED 0 - -#define HIPS_PREHEAT_HOTEND_TEMP 220 -#define HIPS_PREHEAT_HPB_TEMP 100 -#define HIPS_PREHEAT_FAN_SPEED 0 - -#define PP_PREHEAT_HOTEND_TEMP 254 -#define PP_PREHEAT_HPB_TEMP 100 -#define PP_PREHEAT_FAN_SPEED 0 - -#define PET_PREHEAT_HOTEND_TEMP 240 -#define PET_PREHEAT_HPB_TEMP 90 -#define PET_PREHEAT_FAN_SPEED 0 - -#define FLEX_PREHEAT_HOTEND_TEMP 230 -#define FLEX_PREHEAT_HPB_TEMP 50 -#define FLEX_PREHEAT_FAN_SPEED 0 - -// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. -// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) -// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, -// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) -#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current - -// temperature runaway -//#define TEMP_RUNAWAY_BED_HYSTERESIS 5 -//#define TEMP_RUNAWAY_BED_TIMEOUT 360 - -#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15 -#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45 - - -/*------------------------------------ - THERMISTORS SETTINGS -*------------------------------------*/ - -// -//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table -// -//// Temperature sensor settings: -// -2 is thermocouple with MAX6675 (only for sensor 0) -// -1 is thermocouple with AD595 -// 0 is not used -// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) -// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) -// 3 is Mendel-parts thermistor (4.7k pullup) -// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! -// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) -// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) -// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) -// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) -// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) -// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) -// 10 is 100k RS thermistor 198-961 (4.7k pullup) -// 11 is 100k beta 3950 1% thermistor (4.7k pullup) -// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) -// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" -// 20 is the PT100 circuit found in the Ultimainboard V2.x -// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 -// -// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k -// (but gives greater accuracy and more stable PID) -// 51 is 100k thermistor - EPCOS (1k pullup) -// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) -// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) -// -// 1047 is Pt1000 with 4k7 pullup -// 1010 is Pt1000 with 1k pullup (non standard) -// 147 is Pt100 with 4k7 pullup -// 110 is Pt100 with 1k pullup (non standard) - -#define TEMP_SENSOR_0 5 -#define TEMP_SENSOR_1 0 -#define TEMP_SENSOR_2 0 -#define TEMP_SENSOR_BED 1 - - -#endif //__CONFIGURATION_PRUSA_H diff --git a/Firmware/variants/1_75mm-RAMBo10a-E3Dv6lite.h b/Firmware/variants/1_75mm-RAMBo10a-E3Dv6lite.h deleted file mode 100644 index 42c7127c..00000000 --- a/Firmware/variants/1_75mm-RAMBo10a-E3Dv6lite.h +++ /dev/null @@ -1,244 +0,0 @@ -#ifndef CONFIGURATION_PRUSA_H -#define CONFIGURATION_PRUSA_H - -/*------------------------------------ - GENERAL SETTINGS -*------------------------------------*/ - -// Printer revision -#define FILAMENT_SIZE "1_75mm" -#define NOZZLE_TYPE "E3Dv6lite" - -// Printer name -#define CUSTOM_MENDEL_NAME "Prusa i3" - -// Electronics -#define MOTHERBOARD BOARD_RAMBO_MINI_1_0 - - -/*------------------------------------ - AXIS SETTINGS -*------------------------------------*/ - -// Steps per unit {X,Y,Z,E} -#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/0.8,161.3} - -// Endstop inverting -const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. - -// Home position -#define MANUAL_X_HOME_POS 0 -#define MANUAL_Y_HOME_POS 0 -#define MANUAL_Z_HOME_POS 0.25 - -// Travel limits after homing -#define X_MAX_POS 214 -#define X_MIN_POS 0 -#define Y_MAX_POS 198 -#define Y_MIN_POS 0 -#define Z_MAX_POS 201 -#define Z_MIN_POS 0.23 - -// Canceled home position -#define X_CANCEL_POS 50 -#define Y_CANCEL_POS 180 - -#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E -#define HOMING_FEEDRATE {3000, 3000, 240, 0} // set the homing speeds (mm/min) - -#define DEFAULT_MAX_FEEDRATE {500, 500, 3, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,30,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts - - -#define MANUAL_FEEDRATE {3000, 3000, 240, 60} // set the speeds for manual moves (mm/min) - - -/*------------------------------------ - EXTRUDER SETTINGS -*------------------------------------*/ - -// Mintemps -#define HEATER_0_MINTEMP 15 -#define HEATER_1_MINTEMP 5 -#define HEATER_2_MINTEMP 5 -#define BED_MINTEMP 15 - -// Maxtemps -#define HEATER_0_MAXTEMP 265 -#define HEATER_1_MAXTEMP 265 -#define HEATER_2_MAXTEMP 265 -#define BED_MAXTEMP 150 - -// Define PID constants for extruder -#define DEFAULT_Kp 40.925 -#define DEFAULT_Ki 4.875 -#define DEFAULT_Kd 86.085 - -// Extrude mintemp -#define EXTRUDE_MINTEMP 130 - -// Extruder cooling fans -#define EXTRUDER_0_AUTO_FAN_PIN 8 -#define EXTRUDER_1_AUTO_FAN_PIN -1 -#define EXTRUDER_2_AUTO_FAN_PIN -1 -#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 -#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed - - - -/*------------------------------------ - LOAD/UNLOAD FILAMENT SETTINGS -*------------------------------------*/ - -// Load filament commands -#define LOAD_FILAMENT_0 "M83" -#define LOAD_FILAMENT_1 "G1 E70 F400" -#define LOAD_FILAMENT_2 "G1 E40 F100" - -// Unload filament commands -#define UNLOAD_FILAMENT_0 "M83" -#define UNLOAD_FILAMENT_1 "G1 E-80 F400" - -/*------------------------------------ - CHANGE FILAMENT SETTINGS -*------------------------------------*/ - -// Filament change configuration -#define FILAMENTCHANGEENABLE - #ifdef FILAMENTCHANGEENABLE - #define FILAMENTCHANGE_XPOS 211 - #define FILAMENTCHANGE_YPOS 0 - #define FILAMENTCHANGE_ZADD 2 - #define FILAMENTCHANGE_FIRSTRETRACT -2 - #define FILAMENTCHANGE_FINALRETRACT -80 - - #define FILAMENTCHANGE_FIRSTFEED 70 - #define FILAMENTCHANGE_FINALFEED 50 - #define FILAMENTCHANGE_RECFEED 5 - - #define FILAMENTCHANGE_XYFEED 70 - #define FILAMENTCHANGE_EFEED 20 - #define FILAMENTCHANGE_RFEED 400 - #define FILAMENTCHANGE_EXFEED 2 - #define FILAMENTCHANGE_ZFEED 300 - -#endif - -/*------------------------------------ - ADDITIONAL FEATURES SETTINGS -*------------------------------------*/ - -// Define Prusa filament runout sensor -//#define FILAMENT_RUNOUT_SUPPORT - -#ifdef FILAMENT_RUNOUT_SUPPORT - #define FILAMENT_RUNOUT_SENSOR 1 -#endif - -/*------------------------------------ - MOTOR CURRENT SETTINGS -*------------------------------------*/ - -// Motor Current setting for BIG RAMBo -#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) -#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135} - -// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range -#if MOTHERBOARD == 102 || MOTHERBOARD == 302 - #define MOTOR_CURRENT_PWM_RANGE 2000 - #define DEFAULT_PWM_MOTOR_CURRENT {270, 450, 450} // {XY,Z,E} - #define DEFAULT_PWM_MOTOR_CURRENT_LOUD {540, 450, 500} // {XY,Z,E} -#endif - -/*------------------------------------ - PREHEAT SETTINGS -*------------------------------------*/ - -#define PLA_PREHEAT_HOTEND_TEMP 210 -#define PLA_PREHEAT_HPB_TEMP 50 -#define PLA_PREHEAT_FAN_SPEED 0 - -#define ABS_PREHEAT_HOTEND_TEMP 255 -#define ABS_PREHEAT_HPB_TEMP 100 -#define ABS_PREHEAT_FAN_SPEED 0 - -#define HIPS_PREHEAT_HOTEND_TEMP 220 -#define HIPS_PREHEAT_HPB_TEMP 100 -#define HIPS_PREHEAT_FAN_SPEED 0 - -#define PP_PREHEAT_HOTEND_TEMP 254 -#define PP_PREHEAT_HPB_TEMP 100 -#define PP_PREHEAT_FAN_SPEED 0 - -#define PET_PREHEAT_HOTEND_TEMP 240 -#define PET_PREHEAT_HPB_TEMP 90 -#define PET_PREHEAT_FAN_SPEED 0 - -#define FLEX_PREHEAT_HOTEND_TEMP 230 -#define FLEX_PREHEAT_HPB_TEMP 50 -#define FLEX_PREHEAT_FAN_SPEED 0 - -// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. -// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) -// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, -// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) -#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current - -// temperature runaway -//#define TEMP_RUNAWAY_BED_HYSTERESIS 5 -//#define TEMP_RUNAWAY_BED_TIMEOUT 360 - -#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15 -#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45 - -/*------------------------------------ - THERMISTORS SETTINGS -*------------------------------------*/ - -// -//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table -// -//// Temperature sensor settings: -// -2 is thermocouple with MAX6675 (only for sensor 0) -// -1 is thermocouple with AD595 -// 0 is not used -// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) -// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) -// 3 is Mendel-parts thermistor (4.7k pullup) -// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! -// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) -// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) -// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) -// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) -// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) -// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) -// 10 is 100k RS thermistor 198-961 (4.7k pullup) -// 11 is 100k beta 3950 1% thermistor (4.7k pullup) -// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) -// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" -// 20 is the PT100 circuit found in the Ultimainboard V2.x -// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 -// -// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k -// (but gives greater accuracy and more stable PID) -// 51 is 100k thermistor - EPCOS (1k pullup) -// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) -// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) -// -// 1047 is Pt1000 with 4k7 pullup -// 1010 is Pt1000 with 1k pullup (non standard) -// 147 is Pt100 with 4k7 pullup -// 110 is Pt100 with 1k pullup (non standard) - -#define TEMP_SENSOR_0 5 -#define TEMP_SENSOR_1 0 -#define TEMP_SENSOR_2 0 -#define TEMP_SENSOR_BED 1 - - -#endif //__CONFIGURATION_PRUSA_H diff --git a/Firmware/variants/1_75mm-RAMBo13a-E3Dv6full.h b/Firmware/variants/1_75mm-RAMBo13a-E3Dv6full.h deleted file mode 100644 index 327373d0..00000000 --- a/Firmware/variants/1_75mm-RAMBo13a-E3Dv6full.h +++ /dev/null @@ -1,244 +0,0 @@ -#ifndef CONFIGURATION_PRUSA_H -#define CONFIGURATION_PRUSA_H - -/*------------------------------------ - GENERAL SETTINGS -*------------------------------------*/ - -// Printer revision -#define FILAMENT_SIZE "1_75mm" -#define NOZZLE_TYPE "E3Dv6full" - -// Printer name -#define CUSTOM_MENDEL_NAME "Prusa i3" - -// Electronics -#define MOTHERBOARD BOARD_RAMBO_MINI_1_3 - - -/*------------------------------------ - AXIS SETTINGS -*------------------------------------*/ - -// Steps per unit {X,Y,Z,E} -#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/0.8,161.3} - -// Endstop inverting -const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. - -// Home position -#define MANUAL_X_HOME_POS 0 -#define MANUAL_Y_HOME_POS 0 -#define MANUAL_Z_HOME_POS 0.25 - -// Travel limits after homing -#define X_MAX_POS 214 -#define X_MIN_POS 0 -#define Y_MAX_POS 198 -#define Y_MIN_POS 0 -#define Z_MAX_POS 201 -#define Z_MIN_POS 0.23 - -// Canceled home position -#define X_CANCEL_POS 50 -#define Y_CANCEL_POS 180 - -#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E -#define HOMING_FEEDRATE {3000, 3000, 240, 0} // set the homing speeds (mm/min) - -#define DEFAULT_MAX_FEEDRATE {500, 500, 3, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,30,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts - - -#define MANUAL_FEEDRATE {3000, 3000, 240, 60} // set the speeds for manual moves (mm/min) - - -/*------------------------------------ - EXTRUDER SETTINGS -*------------------------------------*/ - -// Mintemps -#define HEATER_0_MINTEMP 15 -#define HEATER_1_MINTEMP 5 -#define HEATER_2_MINTEMP 5 -#define BED_MINTEMP 15 - -// Maxtemps -#define HEATER_0_MAXTEMP 310 -#define HEATER_1_MAXTEMP 310 -#define HEATER_2_MAXTEMP 310 -#define BED_MAXTEMP 150 - -// Define PID constants for extruder -#define DEFAULT_Kp 40.925 -#define DEFAULT_Ki 4.875 -#define DEFAULT_Kd 86.085 - -// Extrude mintemp -#define EXTRUDE_MINTEMP 130 - -// Extruder cooling fans -#define EXTRUDER_0_AUTO_FAN_PIN 8 -#define EXTRUDER_1_AUTO_FAN_PIN -1 -#define EXTRUDER_2_AUTO_FAN_PIN -1 -#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 -#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed - - - -/*------------------------------------ - LOAD/UNLOAD FILAMENT SETTINGS -*------------------------------------*/ - -// Load filament commands -#define LOAD_FILAMENT_0 "M83" -#define LOAD_FILAMENT_1 "G1 E70 F400" -#define LOAD_FILAMENT_2 "G1 E40 F100" - -// Unload filament commands -#define UNLOAD_FILAMENT_0 "M83" -#define UNLOAD_FILAMENT_1 "G1 E-80 F400" - -/*------------------------------------ - CHANGE FILAMENT SETTINGS -*------------------------------------*/ - -// Filament change configuration -#define FILAMENTCHANGEENABLE - #ifdef FILAMENTCHANGEENABLE - #define FILAMENTCHANGE_XPOS 211 - #define FILAMENTCHANGE_YPOS 0 - #define FILAMENTCHANGE_ZADD 2 - #define FILAMENTCHANGE_FIRSTRETRACT -2 - #define FILAMENTCHANGE_FINALRETRACT -80 - - #define FILAMENTCHANGE_FIRSTFEED 70 - #define FILAMENTCHANGE_FINALFEED 50 - #define FILAMENTCHANGE_RECFEED 5 - - #define FILAMENTCHANGE_XYFEED 70 - #define FILAMENTCHANGE_EFEED 20 - #define FILAMENTCHANGE_RFEED 400 - #define FILAMENTCHANGE_EXFEED 2 - #define FILAMENTCHANGE_ZFEED 300 - -#endif - -/*------------------------------------ - ADDITIONAL FEATURES SETTINGS -*------------------------------------*/ - -// Define Prusa filament runout sensor -//#define FILAMENT_RUNOUT_SUPPORT - -#ifdef FILAMENT_RUNOUT_SUPPORT - #define FILAMENT_RUNOUT_SENSOR 1 -#endif - -/*------------------------------------ - MOTOR CURRENT SETTINGS -*------------------------------------*/ - -// Motor Current setting for BIG RAMBo -#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) -#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135} - -// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range -#if MOTHERBOARD == 102 || MOTHERBOARD == 302 - #define MOTOR_CURRENT_PWM_RANGE 2000 - #define DEFAULT_PWM_MOTOR_CURRENT {270, 450, 450} // {XY,Z,E} - #define DEFAULT_PWM_MOTOR_CURRENT_LOUD {540, 450, 500} // {XY,Z,E} -#endif - -/*------------------------------------ - PREHEAT SETTINGS -*------------------------------------*/ - -#define PLA_PREHEAT_HOTEND_TEMP 210 -#define PLA_PREHEAT_HPB_TEMP 50 -#define PLA_PREHEAT_FAN_SPEED 0 - -#define ABS_PREHEAT_HOTEND_TEMP 255 -#define ABS_PREHEAT_HPB_TEMP 100 -#define ABS_PREHEAT_FAN_SPEED 0 - -#define HIPS_PREHEAT_HOTEND_TEMP 220 -#define HIPS_PREHEAT_HPB_TEMP 100 -#define HIPS_PREHEAT_FAN_SPEED 0 - -#define PP_PREHEAT_HOTEND_TEMP 254 -#define PP_PREHEAT_HPB_TEMP 100 -#define PP_PREHEAT_FAN_SPEED 0 - -#define PET_PREHEAT_HOTEND_TEMP 240 -#define PET_PREHEAT_HPB_TEMP 90 -#define PET_PREHEAT_FAN_SPEED 0 - -#define FLEX_PREHEAT_HOTEND_TEMP 230 -#define FLEX_PREHEAT_HPB_TEMP 50 -#define FLEX_PREHEAT_FAN_SPEED 0 - -// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. -// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) -// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, -// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) -#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current - -// temperature runaway -//#define TEMP_RUNAWAY_BED_HYSTERESIS 5 -//#define TEMP_RUNAWAY_BED_TIMEOUT 360 - -#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15 -#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45 - -/*------------------------------------ - THERMISTORS SETTINGS -*------------------------------------*/ - -// -//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table -// -//// Temperature sensor settings: -// -2 is thermocouple with MAX6675 (only for sensor 0) -// -1 is thermocouple with AD595 -// 0 is not used -// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) -// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) -// 3 is Mendel-parts thermistor (4.7k pullup) -// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! -// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) -// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) -// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) -// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) -// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) -// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) -// 10 is 100k RS thermistor 198-961 (4.7k pullup) -// 11 is 100k beta 3950 1% thermistor (4.7k pullup) -// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) -// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" -// 20 is the PT100 circuit found in the Ultimainboard V2.x -// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 -// -// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k -// (but gives greater accuracy and more stable PID) -// 51 is 100k thermistor - EPCOS (1k pullup) -// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) -// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) -// -// 1047 is Pt1000 with 4k7 pullup -// 1010 is Pt1000 with 1k pullup (non standard) -// 147 is Pt100 with 4k7 pullup -// 110 is Pt100 with 1k pullup (non standard) - -#define TEMP_SENSOR_0 5 -#define TEMP_SENSOR_1 0 -#define TEMP_SENSOR_2 0 -#define TEMP_SENSOR_BED 1 - - -#endif //__CONFIGURATION_PRUSA_H diff --git a/Firmware/variants/1_75mm-RAMBo13a-E3Dv6lite.h b/Firmware/variants/1_75mm-RAMBo13a-E3Dv6lite.h deleted file mode 100644 index e9299986..00000000 --- a/Firmware/variants/1_75mm-RAMBo13a-E3Dv6lite.h +++ /dev/null @@ -1,244 +0,0 @@ -#ifndef CONFIGURATION_PRUSA_H -#define CONFIGURATION_PRUSA_H - -/*------------------------------------ - GENERAL SETTINGS -*------------------------------------*/ - -// Printer revision -#define FILAMENT_SIZE "1_75mm" -#define NOZZLE_TYPE "E3Dv6lite" - -// Printer name -#define CUSTOM_MENDEL_NAME "Prusa i3" - -// Electronics -#define MOTHERBOARD BOARD_RAMBO_MINI_1_3 - - -/*------------------------------------ - AXIS SETTINGS -*------------------------------------*/ - -// Steps per unit {X,Y,Z,E} -#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/0.8,161.3} - -// Endstop inverting -const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. - -// Home position -#define MANUAL_X_HOME_POS 0 -#define MANUAL_Y_HOME_POS 0 -#define MANUAL_Z_HOME_POS 0.25 - -// Travel limits after homing -#define X_MAX_POS 214 -#define X_MIN_POS 0 -#define Y_MAX_POS 198 -#define Y_MIN_POS 0 -#define Z_MAX_POS 201 -#define Z_MIN_POS 0.23 - -// Canceled home position -#define X_CANCEL_POS 50 -#define Y_CANCEL_POS 180 - -#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E -#define HOMING_FEEDRATE {3000, 3000, 240, 0} // set the homing speeds (mm/min) - -#define DEFAULT_MAX_FEEDRATE {500, 500, 3, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,30,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts - - -#define MANUAL_FEEDRATE {3000, 3000, 240, 60} // set the speeds for manual moves (mm/min) - - -/*------------------------------------ - EXTRUDER SETTINGS -*------------------------------------*/ - -// Mintemps -#define HEATER_0_MINTEMP 15 -#define HEATER_1_MINTEMP 5 -#define HEATER_2_MINTEMP 5 -#define BED_MINTEMP 15 - -// Maxtemps -#define HEATER_0_MAXTEMP 265 -#define HEATER_1_MAXTEMP 265 -#define HEATER_2_MAXTEMP 265 -#define BED_MAXTEMP 150 - -// Define PID constants for extruder -#define DEFAULT_Kp 40.925 -#define DEFAULT_Ki 4.875 -#define DEFAULT_Kd 86.085 - -// Extrude mintemp -#define EXTRUDE_MINTEMP 130 - -// Extruder cooling fans -#define EXTRUDER_0_AUTO_FAN_PIN 8 -#define EXTRUDER_1_AUTO_FAN_PIN -1 -#define EXTRUDER_2_AUTO_FAN_PIN -1 -#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 -#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed - - - -/*------------------------------------ - LOAD/UNLOAD FILAMENT SETTINGS -*------------------------------------*/ - -// Load filament commands -#define LOAD_FILAMENT_0 "M83" -#define LOAD_FILAMENT_1 "G1 E70 F400" -#define LOAD_FILAMENT_2 "G1 E40 F100" - -// Unload filament commands -#define UNLOAD_FILAMENT_0 "M83" -#define UNLOAD_FILAMENT_1 "G1 E-80 F400" - -/*------------------------------------ - CHANGE FILAMENT SETTINGS -*------------------------------------*/ - -// Filament change configuration -#define FILAMENTCHANGEENABLE - #ifdef FILAMENTCHANGEENABLE - #define FILAMENTCHANGE_XPOS 211 - #define FILAMENTCHANGE_YPOS 0 - #define FILAMENTCHANGE_ZADD 2 - #define FILAMENTCHANGE_FIRSTRETRACT -2 - #define FILAMENTCHANGE_FINALRETRACT -80 - - #define FILAMENTCHANGE_FIRSTFEED 70 - #define FILAMENTCHANGE_FINALFEED 50 - #define FILAMENTCHANGE_RECFEED 5 - - #define FILAMENTCHANGE_XYFEED 70 - #define FILAMENTCHANGE_EFEED 20 - #define FILAMENTCHANGE_RFEED 400 - #define FILAMENTCHANGE_EXFEED 2 - #define FILAMENTCHANGE_ZFEED 300 - -#endif - -/*------------------------------------ - ADDITIONAL FEATURES SETTINGS -*------------------------------------*/ - -// Define Prusa filament runout sensor -//#define FILAMENT_RUNOUT_SUPPORT - -#ifdef FILAMENT_RUNOUT_SUPPORT - #define FILAMENT_RUNOUT_SENSOR 1 -#endif - -/*------------------------------------ - MOTOR CURRENT SETTINGS -*------------------------------------*/ - -// Motor Current setting for BIG RAMBo -#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) -#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135} - -// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range -#if MOTHERBOARD == 102 || MOTHERBOARD == 302 - #define MOTOR_CURRENT_PWM_RANGE 2000 - #define DEFAULT_PWM_MOTOR_CURRENT {270, 450, 450} // {XY,Z,E} - #define DEFAULT_PWM_MOTOR_CURRENT_LOUD {540, 450, 500} // {XY,Z,E} -#endif - -/*------------------------------------ - PREHEAT SETTINGS -*------------------------------------*/ - -#define PLA_PREHEAT_HOTEND_TEMP 210 -#define PLA_PREHEAT_HPB_TEMP 50 -#define PLA_PREHEAT_FAN_SPEED 0 - -#define ABS_PREHEAT_HOTEND_TEMP 255 -#define ABS_PREHEAT_HPB_TEMP 100 -#define ABS_PREHEAT_FAN_SPEED 0 - -#define HIPS_PREHEAT_HOTEND_TEMP 220 -#define HIPS_PREHEAT_HPB_TEMP 100 -#define HIPS_PREHEAT_FAN_SPEED 0 - -#define PP_PREHEAT_HOTEND_TEMP 254 -#define PP_PREHEAT_HPB_TEMP 100 -#define PP_PREHEAT_FAN_SPEED 0 - -#define PET_PREHEAT_HOTEND_TEMP 240 -#define PET_PREHEAT_HPB_TEMP 90 -#define PET_PREHEAT_FAN_SPEED 0 - -#define FLEX_PREHEAT_HOTEND_TEMP 230 -#define FLEX_PREHEAT_HPB_TEMP 50 -#define FLEX_PREHEAT_FAN_SPEED 0 - -// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. -// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) -// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, -// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) -#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current - -// temperature runaway -//#define TEMP_RUNAWAY_BED_HYSTERESIS 5 -//#define TEMP_RUNAWAY_BED_TIMEOUT 360 - -#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15 -#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45 - -/*------------------------------------ - THERMISTORS SETTINGS -*------------------------------------*/ - -// -//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table -// -//// Temperature sensor settings: -// -2 is thermocouple with MAX6675 (only for sensor 0) -// -1 is thermocouple with AD595 -// 0 is not used -// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) -// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) -// 3 is Mendel-parts thermistor (4.7k pullup) -// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! -// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) -// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) -// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) -// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) -// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) -// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) -// 10 is 100k RS thermistor 198-961 (4.7k pullup) -// 11 is 100k beta 3950 1% thermistor (4.7k pullup) -// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) -// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" -// 20 is the PT100 circuit found in the Ultimainboard V2.x -// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 -// -// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k -// (but gives greater accuracy and more stable PID) -// 51 is 100k thermistor - EPCOS (1k pullup) -// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) -// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) -// -// 1047 is Pt1000 with 4k7 pullup -// 1010 is Pt1000 with 1k pullup (non standard) -// 147 is Pt100 with 4k7 pullup -// 110 is Pt100 with 1k pullup (non standard) - -#define TEMP_SENSOR_0 5 -#define TEMP_SENSOR_1 0 -#define TEMP_SENSOR_2 0 -#define TEMP_SENSOR_BED 1 - - -#endif //__CONFIGURATION_PRUSA_H diff --git a/Firmware/variants/1_75mm_MK2-RAMBo10a-E3Dv6full.h b/Firmware/variants/1_75mm_MK2-RAMBo10a-E3Dv6full.h deleted file mode 100644 index d6e73ab7..00000000 --- a/Firmware/variants/1_75mm_MK2-RAMBo10a-E3Dv6full.h +++ /dev/null @@ -1,316 +0,0 @@ -#ifndef CONFIGURATION_PRUSA_H -#define CONFIGURATION_PRUSA_H - -/*------------------------------------ -GENERAL SETTINGS -*------------------------------------*/ - -// Printer revision -#define FILAMENT_SIZE "1_75mm_MK2" -#define NOZZLE_TYPE "E3Dv6full" - -// Developer flag -#define DEVELOPER - -// Printer name -#define CUSTOM_MENDEL_NAME "Prusa i3 MK2" - -// Electronics -#define MOTHERBOARD BOARD_RAMBO_MINI_1_0 - - -/*------------------------------------ -AXIS SETTINGS -*------------------------------------*/ - -// Steps per unit {X,Y,Z,E} -#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,161.3} - -// Endstop inverting -const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. - -// Home position -#define MANUAL_X_HOME_POS 0 -#define MANUAL_Y_HOME_POS -2.2 -#define MANUAL_Z_HOME_POS 0.2 - -// Travel limits after homing -#define X_MAX_POS 255 -#define X_MIN_POS 0 -#define Y_MAX_POS 210 -#define Y_MIN_POS -4 -#define Z_MAX_POS 210 -#define Z_MIN_POS 0.2 - -// Canceled home position -#define X_CANCEL_POS 50 -#define Y_CANCEL_POS 190 - -#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E -#define HOMING_FEEDRATE {3000, 3000, 800, 0} // set the homing speeds (mm/min) - -#define DEFAULT_MAX_FEEDRATE {500, 500, 1000, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,1000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts - - -#define MANUAL_FEEDRATE {3000, 3000, 1000, 100} // set the speeds for manual moves (mm/min) - -#define Z_AXIS_ALWAYS_ON 1 - -/*------------------------------------ -EXTRUDER SETTINGS -*------------------------------------*/ - -// Mintemps -#define HEATER_0_MINTEMP 15 -#define HEATER_1_MINTEMP 5 -#define HEATER_2_MINTEMP 5 -#define BED_MINTEMP 15 - -// Maxtemps -#define HEATER_0_MAXTEMP 305 -#define HEATER_1_MAXTEMP 305 -#define HEATER_2_MAXTEMP 305 -#define BED_MAXTEMP 150 - -// Define PID constants for extruder -#define DEFAULT_Kp 40.925 -#define DEFAULT_Ki 4.875 -#define DEFAULT_Kd 86.085 - -// Extrude mintemp -#define EXTRUDE_MINTEMP 130 - -// Extruder cooling fans -#define EXTRUDER_0_AUTO_FAN_PIN 8 -#define EXTRUDER_1_AUTO_FAN_PIN -1 -#define EXTRUDER_2_AUTO_FAN_PIN -1 -#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 -#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed - - - -/*------------------------------------ -LOAD/UNLOAD FILAMENT SETTINGS -*------------------------------------*/ - -// Load filament commands -#define LOAD_FILAMENT_0 "M83" -#define LOAD_FILAMENT_1 "G1 E70 F400" -#define LOAD_FILAMENT_2 "G1 E40 F100" - -// Unload filament commands -#define UNLOAD_FILAMENT_0 "M83" -#define UNLOAD_FILAMENT_1 "G1 E-80 F400" - -/*------------------------------------ -CHANGE FILAMENT SETTINGS -*------------------------------------*/ - -// Filament change configuration -#define FILAMENTCHANGEENABLE -#ifdef FILAMENTCHANGEENABLE -#define FILAMENTCHANGE_XPOS 211 -#define FILAMENTCHANGE_YPOS 0 -#define FILAMENTCHANGE_ZADD 2 -#define FILAMENTCHANGE_FIRSTRETRACT -2 -#define FILAMENTCHANGE_FINALRETRACT -80 - -#define FILAMENTCHANGE_FIRSTFEED 70 -#define FILAMENTCHANGE_FINALFEED 50 -#define FILAMENTCHANGE_RECFEED 5 - -#define FILAMENTCHANGE_XYFEED 50 -#define FILAMENTCHANGE_EFEED 20 -#define FILAMENTCHANGE_RFEED 400 -#define FILAMENTCHANGE_EXFEED 2 -#define FILAMENTCHANGE_ZFEED 15 - -#endif - -/*------------------------------------ -ADDITIONAL FEATURES SETTINGS -*------------------------------------*/ - -// Define Prusa filament runout sensor -//#define FILAMENT_RUNOUT_SUPPORT - -#ifdef FILAMENT_RUNOUT_SUPPORT -#define FILAMENT_RUNOUT_SENSOR 1 -#endif - -// temperature runaway -//#define TEMP_RUNAWAY_BED_HYSTERESIS 5 -//#define TEMP_RUNAWAY_BED_TIMEOUT 360 - -#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15 -#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45 - -/*------------------------------------ -MOTOR CURRENT SETTINGS -*------------------------------------*/ - -// Motor Current setting for BIG RAMBo -#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) -#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135} - -// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range -#if MOTHERBOARD == 102 || MOTHERBOARD == 302 -#define MOTOR_CURRENT_PWM_RANGE 2000 -#define DEFAULT_PWM_MOTOR_CURRENT {270, 830, 450} // {XY,Z,E} -#define DEFAULT_PWM_MOTOR_CURRENT_LOUD {540, 830, 500} // {XY,Z,E} -#endif - -/*------------------------------------ -BED SETTINGS -*------------------------------------*/ - -// Define Mesh Bed Leveling system to enable it -#define MESH_BED_LEVELING -#ifdef MESH_BED_LEVELING - -#define MBL_Z_STEP 0.01 - -// Mesh definitions -#define MESH_MIN_X 35 -#define MESH_MAX_X 238 -#define MESH_MIN_Y 6 -#define MESH_MAX_Y 202 - -// Mesh upsample definition -#define MESH_NUM_X_POINTS 7 -#define MESH_NUM_Y_POINTS 7 -// Mesh measure definition -#define MESH_MEAS_NUM_X_POINTS 3 -#define MESH_MEAS_NUM_Y_POINTS 3 - -#define MESH_HOME_Z_CALIB 0.2 -#define MESH_HOME_Z_SEARCH 5 - -#define X_PROBE_OFFSET_FROM_EXTRUDER 23 // Z probe to nozzle X offset: -left +right -#define Y_PROBE_OFFSET_FROM_EXTRUDER 9 // Z probe to nozzle Y offset: -front +behind -#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.4 // Z probe to nozzle Z offset: -below (always!) -#endif - -// Bed Temperature Control -// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis -// -// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. -// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz, -// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. -// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. -// If your configuration is significantly different than this and you don't understand the issues involved, you probably -// shouldn't use bed PID until someone else verifies your hardware works. -// If this is enabled, find your own PID constants below. -#define PIDTEMPBED -// -//#define BED_LIMIT_SWITCHING - -// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. -// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) -// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, -// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) -#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current - -// Bed temperature compensation settings -#define BED_OFFSET 10 -#define BED_OFFSET_START 40 -#define BED_OFFSET_CENTER 50 - - -#ifdef PIDTEMPBED -//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) -//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) -#define DEFAULT_bedKp 126.13 -#define DEFAULT_bedKi 4.30 -#define DEFAULT_bedKd 924.76 - -//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) -//from pidautotune -// #define DEFAULT_bedKp 97.1 -// #define DEFAULT_bedKi 1.41 -// #define DEFAULT_bedKd 1675.16 - -// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. -#endif // PIDTEMPBED - - -/*----------------------------------- -PREHEAT SETTINGS -*------------------------------------*/ - -#define PLA_PREHEAT_HOTEND_TEMP 215 -#define PLA_PREHEAT_HPB_TEMP 55 -#define PLA_PREHEAT_FAN_SPEED 0 - -#define ABS_PREHEAT_HOTEND_TEMP 255 -#define ABS_PREHEAT_HPB_TEMP 100 -#define ABS_PREHEAT_FAN_SPEED 0 - -#define HIPS_PREHEAT_HOTEND_TEMP 220 -#define HIPS_PREHEAT_HPB_TEMP 100 -#define HIPS_PREHEAT_FAN_SPEED 0 - -#define PP_PREHEAT_HOTEND_TEMP 254 -#define PP_PREHEAT_HPB_TEMP 100 -#define PP_PREHEAT_FAN_SPEED 0 - -#define PET_PREHEAT_HOTEND_TEMP 240 -#define PET_PREHEAT_HPB_TEMP 90 -#define PET_PREHEAT_FAN_SPEED 0 - -#define FLEX_PREHEAT_HOTEND_TEMP 230 -#define FLEX_PREHEAT_HPB_TEMP 50 -#define FLEX_PREHEAT_FAN_SPEED 0 - -/*------------------------------------ -THERMISTORS SETTINGS -*------------------------------------*/ - -// -//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table -// -//// Temperature sensor settings: -// -2 is thermocouple with MAX6675 (only for sensor 0) -// -1 is thermocouple with AD595 -// 0 is not used -// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) -// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) -// 3 is Mendel-parts thermistor (4.7k pullup) -// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! -// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) -// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) -// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) -// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) -// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) -// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) -// 10 is 100k RS thermistor 198-961 (4.7k pullup) -// 11 is 100k beta 3950 1% thermistor (4.7k pullup) -// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) -// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" -// 20 is the PT100 circuit found in the Ultimainboard V2.x -// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 -// -// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k -// (but gives greater accuracy and more stable PID) -// 51 is 100k thermistor - EPCOS (1k pullup) -// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) -// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) -// -// 1047 is Pt1000 with 4k7 pullup -// 1010 is Pt1000 with 1k pullup (non standard) -// 147 is Pt100 with 4k7 pullup -// 110 is Pt100 with 1k pullup (non standard) - -#define TEMP_SENSOR_0 5 -#define TEMP_SENSOR_1 0 -#define TEMP_SENSOR_2 0 -#define TEMP_SENSOR_BED 1 - - -#endif //__CONFIGURATION_PRUSA_H diff --git a/Firmware/variants/1_75mm_MK2-RAMBo13a-E3Dv6full.h b/Firmware/variants/1_75mm_MK2-RAMBo13a-E3Dv6full.h deleted file mode 100644 index 84d58a12..00000000 --- a/Firmware/variants/1_75mm_MK2-RAMBo13a-E3Dv6full.h +++ /dev/null @@ -1,316 +0,0 @@ -#ifndef CONFIGURATION_PRUSA_H -#define CONFIGURATION_PRUSA_H - -/*------------------------------------ -GENERAL SETTINGS -*------------------------------------*/ - -// Printer revision -#define FILAMENT_SIZE "1_75mm_MK2" -#define NOZZLE_TYPE "E3Dv6full" - -// Developer flag -#define DEVELOPER - -// Printer name -#define CUSTOM_MENDEL_NAME "Prusa i3 MK2" - -// Electronics -#define MOTHERBOARD BOARD_RAMBO_MINI_1_3 - - -/*------------------------------------ -AXIS SETTINGS -*------------------------------------*/ - -// Steps per unit {X,Y,Z,E} -#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,161.3} - -// Endstop inverting -const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. - -// Home position -#define MANUAL_X_HOME_POS 0 -#define MANUAL_Y_HOME_POS -2.2 -#define MANUAL_Z_HOME_POS 0.2 - -// Travel limits after homing -#define X_MAX_POS 255 -#define X_MIN_POS 0 -#define Y_MAX_POS 210 -#define Y_MIN_POS -4 -#define Z_MAX_POS 210 -#define Z_MIN_POS 0.2 - -// Canceled home position -#define X_CANCEL_POS 50 -#define Y_CANCEL_POS 190 - -#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E -#define HOMING_FEEDRATE {3000, 3000, 800, 0} // set the homing speeds (mm/min) - -#define DEFAULT_MAX_FEEDRATE {500, 500, 1000, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,1000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts - - -#define MANUAL_FEEDRATE {3000, 3000, 1000, 100} // set the speeds for manual moves (mm/min) - -#define Z_AXIS_ALWAYS_ON 1 - -/*------------------------------------ -EXTRUDER SETTINGS -*------------------------------------*/ - -// Mintemps -#define HEATER_0_MINTEMP 15 -#define HEATER_1_MINTEMP 5 -#define HEATER_2_MINTEMP 5 -#define BED_MINTEMP 15 - -// Maxtemps -#define HEATER_0_MAXTEMP 305 -#define HEATER_1_MAXTEMP 305 -#define HEATER_2_MAXTEMP 305 -#define BED_MAXTEMP 150 - -// Define PID constants for extruder -#define DEFAULT_Kp 40.925 -#define DEFAULT_Ki 4.875 -#define DEFAULT_Kd 86.085 - -// Extrude mintemp -#define EXTRUDE_MINTEMP 130 - -// Extruder cooling fans -#define EXTRUDER_0_AUTO_FAN_PIN 8 -#define EXTRUDER_1_AUTO_FAN_PIN -1 -#define EXTRUDER_2_AUTO_FAN_PIN -1 -#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 -#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed - - - -/*------------------------------------ -LOAD/UNLOAD FILAMENT SETTINGS -*------------------------------------*/ - -// Load filament commands -#define LOAD_FILAMENT_0 "M83" -#define LOAD_FILAMENT_1 "G1 E70 F400" -#define LOAD_FILAMENT_2 "G1 E40 F100" - -// Unload filament commands -#define UNLOAD_FILAMENT_0 "M83" -#define UNLOAD_FILAMENT_1 "G1 E-80 F400" - -/*------------------------------------ -CHANGE FILAMENT SETTINGS -*------------------------------------*/ - -// Filament change configuration -#define FILAMENTCHANGEENABLE -#ifdef FILAMENTCHANGEENABLE -#define FILAMENTCHANGE_XPOS 211 -#define FILAMENTCHANGE_YPOS 0 -#define FILAMENTCHANGE_ZADD 2 -#define FILAMENTCHANGE_FIRSTRETRACT -2 -#define FILAMENTCHANGE_FINALRETRACT -80 - -#define FILAMENTCHANGE_FIRSTFEED 70 -#define FILAMENTCHANGE_FINALFEED 50 -#define FILAMENTCHANGE_RECFEED 5 - -#define FILAMENTCHANGE_XYFEED 50 -#define FILAMENTCHANGE_EFEED 20 -#define FILAMENTCHANGE_RFEED 400 -#define FILAMENTCHANGE_EXFEED 2 -#define FILAMENTCHANGE_ZFEED 15 - -#endif - -/*------------------------------------ -ADDITIONAL FEATURES SETTINGS -*------------------------------------*/ - -// Define Prusa filament runout sensor -//#define FILAMENT_RUNOUT_SUPPORT - -#ifdef FILAMENT_RUNOUT_SUPPORT -#define FILAMENT_RUNOUT_SENSOR 1 -#endif - -// temperature runaway -//#define TEMP_RUNAWAY_BED_HYSTERESIS 5 -//#define TEMP_RUNAWAY_BED_TIMEOUT 360 - -#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15 -#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45 - -/*------------------------------------ -MOTOR CURRENT SETTINGS -*------------------------------------*/ - -// Motor Current setting for BIG RAMBo -#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) -#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135} - -// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range -#if MOTHERBOARD == 102 || MOTHERBOARD == 302 -#define MOTOR_CURRENT_PWM_RANGE 2000 -#define DEFAULT_PWM_MOTOR_CURRENT {270, 830, 450} // {XY,Z,E} -#define DEFAULT_PWM_MOTOR_CURRENT_LOUD {540, 830, 500} // {XY,Z,E} -#endif - -/*------------------------------------ -BED SETTINGS -*------------------------------------*/ - -// Define Mesh Bed Leveling system to enable it -#define MESH_BED_LEVELING -#ifdef MESH_BED_LEVELING - -#define MBL_Z_STEP 0.01 - -// Mesh definitions -#define MESH_MIN_X 35 -#define MESH_MAX_X 238 -#define MESH_MIN_Y 6 -#define MESH_MAX_Y 202 - -// Mesh upsample definition -#define MESH_NUM_X_POINTS 7 -#define MESH_NUM_Y_POINTS 7 -// Mesh measure definition -#define MESH_MEAS_NUM_X_POINTS 3 -#define MESH_MEAS_NUM_Y_POINTS 3 - -#define MESH_HOME_Z_CALIB 0.2 -#define MESH_HOME_Z_SEARCH 5 - -#define X_PROBE_OFFSET_FROM_EXTRUDER 23 // Z probe to nozzle X offset: -left +right -#define Y_PROBE_OFFSET_FROM_EXTRUDER 9 // Z probe to nozzle Y offset: -front +behind -#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.4 // Z probe to nozzle Z offset: -below (always!) -#endif - -// Bed Temperature Control -// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis -// -// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. -// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz, -// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. -// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. -// If your configuration is significantly different than this and you don't understand the issues involved, you probably -// shouldn't use bed PID until someone else verifies your hardware works. -// If this is enabled, find your own PID constants below. -#define PIDTEMPBED -// -//#define BED_LIMIT_SWITCHING - -// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. -// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) -// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, -// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) -#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current - -// Bed temperature compensation settings -#define BED_OFFSET 10 -#define BED_OFFSET_START 40 -#define BED_OFFSET_CENTER 50 - - -#ifdef PIDTEMPBED -//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) -//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) -#define DEFAULT_bedKp 126.13 -#define DEFAULT_bedKi 4.30 -#define DEFAULT_bedKd 924.76 - -//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) -//from pidautotune -// #define DEFAULT_bedKp 97.1 -// #define DEFAULT_bedKi 1.41 -// #define DEFAULT_bedKd 1675.16 - -// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. -#endif // PIDTEMPBED - - -/*----------------------------------- -PREHEAT SETTINGS -*------------------------------------*/ - -#define PLA_PREHEAT_HOTEND_TEMP 215 -#define PLA_PREHEAT_HPB_TEMP 55 -#define PLA_PREHEAT_FAN_SPEED 0 - -#define ABS_PREHEAT_HOTEND_TEMP 255 -#define ABS_PREHEAT_HPB_TEMP 100 -#define ABS_PREHEAT_FAN_SPEED 0 - -#define HIPS_PREHEAT_HOTEND_TEMP 220 -#define HIPS_PREHEAT_HPB_TEMP 100 -#define HIPS_PREHEAT_FAN_SPEED 0 - -#define PP_PREHEAT_HOTEND_TEMP 254 -#define PP_PREHEAT_HPB_TEMP 100 -#define PP_PREHEAT_FAN_SPEED 0 - -#define PET_PREHEAT_HOTEND_TEMP 240 -#define PET_PREHEAT_HPB_TEMP 90 -#define PET_PREHEAT_FAN_SPEED 0 - -#define FLEX_PREHEAT_HOTEND_TEMP 230 -#define FLEX_PREHEAT_HPB_TEMP 50 -#define FLEX_PREHEAT_FAN_SPEED 0 - -/*------------------------------------ -THERMISTORS SETTINGS -*------------------------------------*/ - -// -//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table -// -//// Temperature sensor settings: -// -2 is thermocouple with MAX6675 (only for sensor 0) -// -1 is thermocouple with AD595 -// 0 is not used -// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) -// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) -// 3 is Mendel-parts thermistor (4.7k pullup) -// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! -// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) -// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) -// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) -// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) -// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) -// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) -// 10 is 100k RS thermistor 198-961 (4.7k pullup) -// 11 is 100k beta 3950 1% thermistor (4.7k pullup) -// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) -// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" -// 20 is the PT100 circuit found in the Ultimainboard V2.x -// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 -// -// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k -// (but gives greater accuracy and more stable PID) -// 51 is 100k thermistor - EPCOS (1k pullup) -// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) -// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) -// -// 1047 is Pt1000 with 4k7 pullup -// 1010 is Pt1000 with 1k pullup (non standard) -// 147 is Pt100 with 4k7 pullup -// 110 is Pt100 with 1k pullup (non standard) - -#define TEMP_SENSOR_0 5 -#define TEMP_SENSOR_1 0 -#define TEMP_SENSOR_2 0 -#define TEMP_SENSOR_BED 1 - - -#endif //__CONFIGURATION_PRUSA_H diff --git a/Firmware/variants/1_75mm_MK3-EINY03-E3Dv6full.h b/Firmware/variants/1_75mm_MK3-EINY03-E3Dv6full.h deleted file mode 100644 index 41afcb87..00000000 --- a/Firmware/variants/1_75mm_MK3-EINY03-E3Dv6full.h +++ /dev/null @@ -1,484 +0,0 @@ -#ifndef CONFIGURATION_PRUSA_H -#define CONFIGURATION_PRUSA_H - -/*------------------------------------ - GENERAL SETTINGS - *------------------------------------*/ - -// Printer revision -#define FILAMENT_SIZE "1_75mm_MK3" -#define NOZZLE_TYPE "E3Dv6full" - -// Developer flag -#define DEVELOPER - -// Printer name -#define CUSTOM_MENDEL_NAME "Prusa i3 MK3" - -// Electronics -#define MOTHERBOARD BOARD_EINY_0_3a - - -// Uncomment the below for the E3D PT100 temperature sensor (with or without PT100 Amplifier) -//#define E3D_PT100_EXTRUDER_WITH_AMP -//#define E3D_PT100_EXTRUDER_NO_AMP -//#define E3D_PT100_BED_WITH_AMP -//#define E3D_PT100_BED_NO_AMP - - -/*------------------------------------ - AXIS SETTINGS - *------------------------------------*/ - -// Steps per unit {X,Y,Z,E} -//#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,140} -#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,280} //Extruder motor changed back to 200step type - -// Endstop inverting -const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. - -// Home position -#define MANUAL_X_HOME_POS 0 -#define MANUAL_Y_HOME_POS -2.2 -#define MANUAL_Z_HOME_POS 0.2 - -// Travel limits after homing -#define X_MAX_POS 255 -#define X_MIN_POS 0 -#define Y_MAX_POS 210 -#define Y_MIN_POS -12 //orig -4 -#define Z_MAX_POS 210 -#define Z_MIN_POS 0.15 - -// Canceled home position -#define X_CANCEL_POS 50 -#define Y_CANCEL_POS 190 - -//Pause print position -#define X_PAUSE_POS 50 -#define Y_PAUSE_POS 190 -#define Z_PAUSE_LIFT 20 - -#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E -#define HOMING_FEEDRATE {3000, 3000, 800, 0} // set the homing speeds (mm/min) // 3000 is also valid for stallGuard homing. Valid range: 2200 - 3000 - -//#define DEFAULT_MAX_FEEDRATE {400, 400, 12, 120} // (mm/sec) -#define DEFAULT_MAX_FEEDRATE {500, 500, 12, 120} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {1000, 1000, 200, 5000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 1250 // X, Y, Z and E max acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 1250 // X, Y, Z and E max acceleration in mm/s^2 for retracts - -#define MANUAL_FEEDRATE {2700, 2700, 1000, 100} // set the speeds for manual moves (mm/min) -//#define MAX_SILENT_FEEDRATE 2700 // - -#define Z_AXIS_ALWAYS_ON 1 - -//DEBUG -#if 0 -#define DEBUG_DCODES //D codes -#define DEBUG_DISABLE_XMINLIMIT //x min limit ignored -#define DEBUG_DISABLE_XMAXLIMIT //x max limit ignored -#define DEBUG_DISABLE_YMINLIMIT //y min limit ignored -#define DEBUG_DISABLE_YMAXLIMIT //y max limit ignored -#define DEBUG_DISABLE_ZMINLIMIT //z min limit ignored -#define DEBUG_DISABLE_ZMAXLIMIT //z max limit ignored -#define DEBUG_DISABLE_STARTMSGS //no startup messages -#define DEBUG_DISABLE_MINTEMP //mintemp error ignored -#define DEBUG_DISABLE_SWLIMITS //sw limits ignored -#define DEBUG_DISABLE_LCD_STATUS_LINE //empty four lcd line -#define DEBUG_DISABLE_PREVENT_EXTRUDER //cold extrusion and long extrusion allowed -#define DEBUG_DISABLE_PRUSA_STATISTICS //disable prusa_statistics() mesages -//#define DEBUG_XSTEP_DUP_PIN 21 //duplicate x-step output to pin 21 (SCL on P3) -//#define DEBUG_YSTEP_DUP_PIN 21 //duplicate y-step output to pin 21 (SCL on P3) -//#define DEBUG_BLINK_ACTIVE -#endif - -/*------------------------------------ - TMC2130 default settings - *------------------------------------*/ - -#define TMC2130_FCLK 12000000 // fclk = 12MHz - -#define TMC2130_USTEPS_XY 16 // microstep resolution for XY axes -#define TMC2130_USTEPS_Z 16 // microstep resolution for Z axis -#define TMC2130_USTEPS_E 32 // microstep resolution for E axis (increased from 16 to 32) -#define TMC2130_INTPOL_XY 1 // extrapolate 256 for XY axes -#define TMC2130_INTPOL_Z 1 // extrapolate 256 for Z axis -#define TMC2130_INTPOL_E 1 // extrapolate 256 for E axis - -#define TMC2130_PWM_GRAD_X 4 // PWMCONF -#define TMC2130_PWM_AMPL_X 200 // PWMCONF -#define TMC2130_PWM_AUTO_X 1 // PWMCONF -#define TMC2130_PWM_FREQ_X 2 // PWMCONF - -#define TMC2130_PWM_GRAD_Y 4 // PWMCONF -#define TMC2130_PWM_AMPL_Y 210 // PWMCONF -#define TMC2130_PWM_AUTO_Y 1 // PWMCONF -#define TMC2130_PWM_FREQ_Y 2 // PWMCONF - -/* //not used -#define TMC2130_PWM_GRAD_Z 4 // PWMCONF -#define TMC2130_PWM_AMPL_Z 200 // PWMCONF -#define TMC2130_PWM_AUTO_Z 1 // PWMCONF -#define TMC2130_PWM_FREQ_Z 2 // PWMCONF -#define TMC2130_PWM_GRAD_E 4 // PWMCONF -#define TMC2130_PWM_AMPL_E 200 // PWMCONF -#define TMC2130_PWM_AUTO_E 1 // PWMCONF -#define TMC2130_PWM_FREQ_E 2 // PWMCONF -*/ - -//#define TMC2130_PWM_DIV 683 // PWM frequency divider (1024, 683, 512, 410) -#define TMC2130_PWM_DIV 512 // PWM frequency divider (1024, 683, 512, 410) -#define TMC2130_PWM_CLK (2 * TMC2130_FCLK / TMC2130_PWM_DIV) // PWM frequency (23.4kHz, 35.1kHz, 46.9kHz, 58.5kHz for 12MHz fclk) - -#define TMC2130_TPWMTHRS 0 // TPWMTHRS - Sets the switching speed threshold based on TSTEP from stealthChop to spreadCycle mode -#define TMC2130_THIGH 0 // THIGH - unused - -#define TMC2130_TCOOLTHRS 239 // TCOOLTHRS - coolstep treshold - -#define TMC2130_SG_HOMING 1 // stallguard homing -#define TMC2130_SG_HOMING_SW_Z 1 // stallguard "software" homing for Z axis -#define TMC2130_SG_THRS_X 0 // stallguard sensitivity for X axis -#define TMC2130_SG_THRS_Y 0 // stallguard sensitivity for Y axis -#define TMC2130_SG_THRS_Z 2 // stallguard sensitivity for Z axis -#define TMC2130_SG_DELTA 128 // stallguard delta [usteps] (minimum usteps before stallguard readed - SW homing) - -//new settings is possible for vsense = 1, running current value > 31 set vsense to zero and shift both currents by 1 bit right (Z axis only) -#define TMC2130_CURRENTS_H {3, 3, 5, 8} // default holding currents for all axes -#define TMC2130_CURRENTS_R {13, 18, 20, 22} // default running currents for all axes - -//#define TMC2130_DEBUG -//#define TMC2130_DEBUG_WR -//#define TMC2130_DEBUG_RD - - -/*------------------------------------ - EXTRUDER SETTINGS - *------------------------------------*/ - -// Mintemps -#define HEATER_0_MINTEMP 15 -#define HEATER_1_MINTEMP 5 -#define HEATER_2_MINTEMP 5 -#define BED_MINTEMP 15 - -// Maxtemps -#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP) -#define HEATER_0_MAXTEMP 410 -#else -#define HEATER_0_MAXTEMP 305 -#endif -#define HEATER_1_MAXTEMP 305 -#define HEATER_2_MAXTEMP 305 -#define BED_MAXTEMP 150 - -#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP) -// Define PID constants for extruder with PT100 -#define DEFAULT_Kp 21.70 -#define DEFAULT_Ki 1.60 -#define DEFAULT_Kd 73.76 -#else -// Define PID constants for extruder -//#define DEFAULT_Kp 40.925 -//#define DEFAULT_Ki 4.875 -//#define DEFAULT_Kd 86.085 -#define DEFAULT_Kp 16.13 -#define DEFAULT_Ki 1.1625 -#define DEFAULT_Kd 56.23 -#endif - -// Extrude mintemp -#define EXTRUDE_MINTEMP 130 - -// Extruder cooling fans -#define EXTRUDER_0_AUTO_FAN_PIN 8 -#define EXTRUDER_1_AUTO_FAN_PIN -1 -#define EXTRUDER_2_AUTO_FAN_PIN -1 -#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 -#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed - - - -/*------------------------------------ - LOAD/UNLOAD FILAMENT SETTINGS - *------------------------------------*/ - -// Load filament commands -#define LOAD_FILAMENT_0 "M83" -#define LOAD_FILAMENT_1 "G1 E70 F400" -#define LOAD_FILAMENT_2 "G1 E40 F100" - -// Unload filament commands -#define UNLOAD_FILAMENT_0 "M83" -#define UNLOAD_FILAMENT_1 "G1 E-80 F7000" - -/*------------------------------------ - CHANGE FILAMENT SETTINGS - *------------------------------------*/ - -// Filament change configuration -#define FILAMENTCHANGEENABLE -#ifdef FILAMENTCHANGEENABLE -#define FILAMENTCHANGE_XPOS 211 -#define FILAMENTCHANGE_YPOS 0 -#define FILAMENTCHANGE_ZADD 2 -#define FILAMENTCHANGE_FIRSTRETRACT -2 -#define FILAMENTCHANGE_FINALRETRACT -80 - -#define FILAMENTCHANGE_FIRSTFEED 70 -#define FILAMENTCHANGE_FINALFEED 50 -#define FILAMENTCHANGE_RECFEED 5 - -#define FILAMENTCHANGE_XYFEED 50 -#define FILAMENTCHANGE_EFEED 20 -#define FILAMENTCHANGE_RFEED 400 -#define FILAMENTCHANGE_EXFEED 2 -#define FILAMENTCHANGE_ZFEED 15 - -#endif - -/*------------------------------------ - ADDITIONAL FEATURES SETTINGS - *------------------------------------*/ - -// Define Prusa filament runout sensor -//#define FILAMENT_RUNOUT_SUPPORT - -#ifdef FILAMENT_RUNOUT_SUPPORT -#define FILAMENT_RUNOUT_SENSOR 1 -#endif - -// temperature runaway -//#define TEMP_RUNAWAY_BED_HYSTERESIS 5 -//#define TEMP_RUNAWAY_BED_TIMEOUT 360 - -#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15 -#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45 - -/*------------------------------------ - MOTOR CURRENT SETTINGS - *------------------------------------*/ - -// Motor Current setting for BIG RAMBo -#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) -#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135} - -// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range -#if MOTHERBOARD == 200 || MOTHERBOARD == 203 || MOTHERBOARD == 303 || MOTHERBOARD == 304 || MOTHERBOARD == 305 -#define MOTOR_CURRENT_PWM_RANGE 2000 -#define DEFAULT_PWM_MOTOR_CURRENT {400, 750, 750} // {XY,Z,E} -#define DEFAULT_PWM_MOTOR_CURRENT_LOUD {400, 750, 750} // {XY,Z,E} -#endif - -/*------------------------------------ - BED SETTINGS - *------------------------------------*/ - -// Define Mesh Bed Leveling system to enable it -#define MESH_BED_LEVELING -#ifdef MESH_BED_LEVELING - -#define MBL_Z_STEP 0.01 - -// Mesh definitions -#define MESH_MIN_X 35 -#define MESH_MAX_X 238 -#define MESH_MIN_Y 6 -#define MESH_MAX_Y 202 - -// Mesh upsample definition -#define MESH_NUM_X_POINTS 7 -#define MESH_NUM_Y_POINTS 7 -// Mesh measure definition -#define MESH_MEAS_NUM_X_POINTS 3 -#define MESH_MEAS_NUM_Y_POINTS 3 - -#define MESH_HOME_Z_CALIB 0.2 -#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc. - -#define X_PROBE_OFFSET_FROM_EXTRUDER 23 // Z probe to nozzle X offset: -left +right -#define Y_PROBE_OFFSET_FROM_EXTRUDER 9 // Z probe to nozzle Y offset: -front +behind -#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.4 // Z probe to nozzle Z offset: -below (always!) -#endif - -// Bed Temperature Control -// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis -// -// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. -// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz, -// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. -// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. -// If your configuration is significantly different than this and you don't understand the issues involved, you probably -// shouldn't use bed PID until someone else verifies your hardware works. -// If this is enabled, find your own PID constants below. -#define PIDTEMPBED -// -//#define BED_LIMIT_SWITCHING - -// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. -// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) -// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, -// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) -#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current - -// Bed temperature compensation settings -#define BED_OFFSET 10 -#define BED_OFFSET_START 40 -#define BED_OFFSET_CENTER 50 - - -#ifdef PIDTEMPBED -//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) -//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) -#if defined(E3D_PT100_BED_WITH_AMP) || defined(E3D_PT100_BED_NO_AMP) -// Define PID constants for extruder with PT100 -#define DEFAULT_bedKp 21.70 -#define DEFAULT_bedKi 1.60 -#define DEFAULT_bedKd 73.76 -#else -#define DEFAULT_bedKp 126.13 -#define DEFAULT_bedKi 4.30 -#define DEFAULT_bedKd 924.76 -#endif - -//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) -//from pidautotune -// #define DEFAULT_bedKp 97.1 -// #define DEFAULT_bedKi 1.41 -// #define DEFAULT_bedKd 1675.16 - -// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. -#endif // PIDTEMPBED - - -/*----------------------------------- - PREHEAT SETTINGS - *------------------------------------*/ - -#define PLA_PREHEAT_HOTEND_TEMP 215 -#define PLA_PREHEAT_HPB_TEMP 55 -#define PLA_PREHEAT_FAN_SPEED 0 - -#define ABS_PREHEAT_HOTEND_TEMP 255 -#define ABS_PREHEAT_HPB_TEMP 100 -#define ABS_PREHEAT_FAN_SPEED 0 - -#define HIPS_PREHEAT_HOTEND_TEMP 220 -#define HIPS_PREHEAT_HPB_TEMP 100 -#define HIPS_PREHEAT_FAN_SPEED 0 - -#define PP_PREHEAT_HOTEND_TEMP 254 -#define PP_PREHEAT_HPB_TEMP 100 -#define PP_PREHEAT_FAN_SPEED 0 - -#define PET_PREHEAT_HOTEND_TEMP 240 -#define PET_PREHEAT_HPB_TEMP 90 -#define PET_PREHEAT_FAN_SPEED 0 - -#define FLEX_PREHEAT_HOTEND_TEMP 230 -#define FLEX_PREHEAT_HPB_TEMP 50 -#define FLEX_PREHEAT_FAN_SPEED 0 - -/*------------------------------------ - THERMISTORS SETTINGS - *------------------------------------*/ - -// -//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table -// -//// Temperature sensor settings: -// -2 is thermocouple with MAX6675 (only for sensor 0) -// -1 is thermocouple with AD595 -// 0 is not used -// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) -// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) -// 3 is Mendel-parts thermistor (4.7k pullup) -// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! -// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) -// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) -// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) -// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) -// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) -// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) -// 10 is 100k RS thermistor 198-961 (4.7k pullup) -// 11 is 100k beta 3950 1% thermistor (4.7k pullup) -// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) -// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" -// 20 is the PT100 circuit found in the Ultimainboard V2.x -// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 -// -// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k -// (but gives greater accuracy and more stable PID) -// 51 is 100k thermistor - EPCOS (1k pullup) -// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) -// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) -// -// 1047 is Pt1000 with 4k7 pullup -// 1010 is Pt1000 with 1k pullup (non standard) -// 147 is Pt100 with 4k7 pullup -// 148 is E3D Pt100 with 4k7 pullup and no PT100 Amplifier on a MiniRambo 1.3a -// 247 is Pt100 with 4k7 pullup and PT100 Amplifier -// 110 is Pt100 with 1k pullup (non standard) - -#if defined(E3D_PT100_EXTRUDER_WITH_AMP) -#define TEMP_SENSOR_0 247 -#elif defined(E3D_PT100_EXTRUDER_NO_AMP) -#define TEMP_SENSOR_0 148 -#else -#define TEMP_SENSOR_0 5 -#endif -#define TEMP_SENSOR_1 0 -#define TEMP_SENSOR_2 0 -#if defined(E3D_PT100_BED_WITH_AMP) -#define TEMP_SENSOR_BED 247 -#elif defined(E3D_PT100_BED_NO_AMP) -#define TEMP_SENSOR_BED 148 -#else -#define TEMP_SENSOR_BED 1 -#endif -#define TEMP_SENSOR_PINDA 1 -#define TEMP_SENSOR_AMBIENT 2000 - -#define STACK_GUARD_TEST_VALUE 0xA2A2 - -#define MAX_BED_TEMP_CALIBRATION 50 -#define MAX_HOTEND_TEMP_CALIBRATION 50 - -#define MAX_E_STEPS_PER_UNIT 250 -#define MIN_E_STEPS_PER_UNIT 100 - -#define Z_BABYSTEP_MIN -3999 -#define Z_BABYSTEP_MAX 0 - -#define PINDA_PREHEAT_X 70 -#define PINDA_PREHEAT_Y -3 -#define PINDA_PREHEAT_Z 1 -#define PINDA_HEAT_T 120 //time in s - -#define PINDA_MIN_T 50 -#define PINDA_STEP_T 10 -#define PINDA_MAX_T 100 - -#define PING_TIME 60 //time in s -#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid false triggering when dealing with long gcodes -#define PING_ALLERT_PERIOD 60 //time in s - -#define LONG_PRESS_TIME 1000 //time in ms for button long press -#define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release - -#define DEFAULT_PID_TEMP 210 - -#define MIN_PRINT_FAN_SPEED 50 - -#ifdef SNMM -#define DEFAULT_RETRACTION 4 //used for PINDA temp calibration and pause print -#else -#define DEFAULT_RETRACTION 1 //used for PINDA temp calibration and pause print -#endif - -#define UVLO_Z_AXIS_SHIFT 2 - -#endif //__CONFIGURATION_PRUSA_H diff --git a/Firmware/variants/1_75mm_MK3-EINY10a-E3Dv6full.h b/Firmware/variants/1_75mm_MK3-EINY10a-E3Dv6full.h deleted file mode 100644 index dbc6cb75..00000000 --- a/Firmware/variants/1_75mm_MK3-EINY10a-E3Dv6full.h +++ /dev/null @@ -1,512 +0,0 @@ -#ifndef CONFIGURATION_PRUSA_H -#define CONFIGURATION_PRUSA_H - -/*------------------------------------ - GENERAL SETTINGS - *------------------------------------*/ - -// Printer revision -#define FILAMENT_SIZE "1_75mm_MK3" -#define NOZZLE_TYPE "E3Dv6full" - -// Developer flag -#define DEVELOPER - -// Printer name -#define CUSTOM_MENDEL_NAME "Prusa i3 MK3" - -// Electronics -#define MOTHERBOARD BOARD_EINY_0_4a - - -// Uncomment the below for the E3D PT100 temperature sensor (with or without PT100 Amplifier) -//#define E3D_PT100_EXTRUDER_WITH_AMP -//#define E3D_PT100_EXTRUDER_NO_AMP -//#define E3D_PT100_BED_WITH_AMP -//#define E3D_PT100_BED_NO_AMP - - -/*------------------------------------ - AXIS SETTINGS - *------------------------------------*/ - -// Steps per unit {X,Y,Z,E} -//#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,140} -//#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,280} -#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/8,560} - -// Endstop inverting -const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. - -// Home position -#define MANUAL_X_HOME_POS 0 -#define MANUAL_Y_HOME_POS -2.2 -#define MANUAL_Z_HOME_POS 0.2 - -// Travel limits after homing -#define X_MAX_POS 255 -#define X_MIN_POS 0 -#define Y_MAX_POS 210 -#define Y_MIN_POS -12 //orig -4 -#define Z_MAX_POS 210 -#define Z_MIN_POS 0.15 - -// Canceled home position -#define X_CANCEL_POS 50 -#define Y_CANCEL_POS 190 - -//Pause print position -#define X_PAUSE_POS 50 -#define Y_PAUSE_POS 190 -#define Z_PAUSE_LIFT 20 - -#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E -#define HOMING_FEEDRATE {2500, 3000, 800, 0} // set the homing speeds (mm/min) // 3000 is also valid for stallGuard homing. Valid range: 2200 - 3000 - -//#define DEFAULT_MAX_FEEDRATE {400, 400, 12, 120} // (mm/sec) -#define DEFAULT_MAX_FEEDRATE {500, 500, 12, 120} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {1000, 1000, 200, 5000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 1250 // X, Y, Z and E max acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 1250 // X, Y, Z and E max acceleration in mm/s^2 for retracts - -#define MANUAL_FEEDRATE {2700, 2700, 1000, 100} // set the speeds for manual moves (mm/min) -//#define MAX_SILENT_FEEDRATE 2700 // - -#define Z_AXIS_ALWAYS_ON 1 - -// Automatic recovery after crash is detected -#define AUTOMATIC_RECOVERY_AFTER_CRASH - -//DEBUG -#define DEBUG_DCODES //D codes -#if 1 -//#define DEBUG_FSENSOR_LOG //Reports fsensor status to serial -//#define DEBUG_CRASHDET_COUNTERS //Display crash-detection counters on LCD -//#define DEBUG_RESUME_PRINT //Resume/save print debug enable -//#define DEBUG_UVLO_AUTOMATIC_RECOVER // Power panic automatic recovery debug output -//#define DEBUG_DISABLE_XMINLIMIT //x min limit ignored -//#define DEBUG_DISABLE_XMAXLIMIT //x max limit ignored -//#define DEBUG_DISABLE_YMINLIMIT //y min limit ignored -//#define DEBUG_DISABLE_YMAXLIMIT //y max limit ignored -//#define DEBUG_DISABLE_ZMINLIMIT //z min limit ignored -//#define DEBUG_DISABLE_ZMAXLIMIT //z max limit ignored -#define DEBUG_DISABLE_STARTMSGS //no startup messages -//#define DEBUG_DISABLE_MINTEMP //mintemp error ignored -//#define DEBUG_DISABLE_SWLIMITS //sw limits ignored -//#define DEBUG_DISABLE_LCD_STATUS_LINE //empty four lcd line -//#define DEBUG_DISABLE_PREVENT_EXTRUDER //cold extrusion and long extrusion allowed -#define DEBUG_DISABLE_PRUSA_STATISTICS //disable prusa_statistics() mesages -//#define DEBUG_XSTEP_DUP_PIN 21 //duplicate x-step output to pin 21 (SCL on P3) -//#define DEBUG_YSTEP_DUP_PIN 21 //duplicate y-step output to pin 21 (SCL on P3) -//#define DEBUG_BLINK_ACTIVE -#endif - -/*------------------------------------ - TMC2130 default settings - *------------------------------------*/ - -#define TMC2130_FCLK 12000000 // fclk = 12MHz - -#define TMC2130_USTEPS_XY 16 // microstep resolution for XY axes -#define TMC2130_USTEPS_Z 16 // microstep resolution for Z axis -#define TMC2130_USTEPS_E 64 // microstep resolution for E axis -#define TMC2130_INTPOL_XY 1 // extrapolate 256 for XY axes -#define TMC2130_INTPOL_Z 1 // extrapolate 256 for Z axis -#define TMC2130_INTPOL_E 1 // extrapolate 256 for E axis - -#define TMC2130_PWM_GRAD_X 2 // PWMCONF -#define TMC2130_PWM_AMPL_X 230 // PWMCONF -#define TMC2130_PWM_AUTO_X 1 // PWMCONF -#define TMC2130_PWM_FREQ_X 2 // PWMCONF - -#define TMC2130_PWM_GRAD_Y 2 // PWMCONF -#define TMC2130_PWM_AMPL_Y 235 // PWMCONF -#define TMC2130_PWM_AUTO_Y 1 // PWMCONF -#define TMC2130_PWM_FREQ_Y 2 // PWMCONF - -/* //not used -#define TMC2130_PWM_GRAD_Z 4 // PWMCONF -#define TMC2130_PWM_AMPL_Z 200 // PWMCONF -#define TMC2130_PWM_AUTO_Z 1 // PWMCONF -#define TMC2130_PWM_FREQ_Z 2 // PWMCONF -#define TMC2130_PWM_GRAD_E 4 // PWMCONF -#define TMC2130_PWM_AMPL_E 200 // PWMCONF -#define TMC2130_PWM_AUTO_E 1 // PWMCONF -#define TMC2130_PWM_FREQ_E 2 // PWMCONF -*/ - -//#define TMC2130_PWM_DIV 683 // PWM frequency divider (1024, 683, 512, 410) -#define TMC2130_PWM_DIV 512 // PWM frequency divider (1024, 683, 512, 410) -#define TMC2130_PWM_CLK (2 * TMC2130_FCLK / TMC2130_PWM_DIV) // PWM frequency (23.4kHz, 35.1kHz, 46.9kHz, 58.5kHz for 12MHz fclk) - -#define TMC2130_TPWMTHRS 0 // TPWMTHRS - Sets the switching speed threshold based on TSTEP from stealthChop to spreadCycle mode -#define TMC2130_THIGH 0 // THIGH - unused - -//#define TMC2130_TCOOLTHRS_X 450 // TCOOLTHRS - coolstep treshold -//#define TMC2130_TCOOLTHRS_Y 450 // TCOOLTHRS - coolstep treshold -#define TMC2130_TCOOLTHRS_X 430 // TCOOLTHRS - coolstep treshold -#define TMC2130_TCOOLTHRS_Y 430 // TCOOLTHRS - coolstep treshold -#define TMC2130_TCOOLTHRS_Z 500 // TCOOLTHRS - coolstep treshold -#define TMC2130_TCOOLTHRS_E 500 // TCOOLTHRS - coolstep treshold - -#define TMC2130_SG_HOMING 1 // stallguard homing -//#define TMC2130_SG_HOMING_SW_XY 1 // stallguard "software" homing for XY axes -#define TMC2130_SG_HOMING_SW_Z 1 // stallguard "software" homing for Z axis -#define TMC2130_SG_THRS_X 1 // stallguard sensitivity for X axis -#define TMC2130_SG_THRS_Y 3 // stallguard sensitivity for Y axis -#define TMC2130_SG_THRS_Z 3 // stallguard sensitivity for Z axis -#define TMC2130_SG_THRS_E 3 // stallguard sensitivity for E axis -#define TMC2130_SG_DELTA 128 // stallguard delta [usteps] (minimum usteps before stallguard readed - SW homing) - -//new settings is possible for vsense = 1, running current value > 31 set vsense to zero and shift both currents by 1 bit right (Z axis only) -#define TMC2130_CURRENTS_H {3, 3, 20, 28} // default holding currents for all axes -#define TMC2130_CURRENTS_R {13, 20, 20, 28} // default running currents for all axes - -//#define TMC2130_DEBUG -//#define TMC2130_DEBUG_WR -//#define TMC2130_DEBUG_RD - - -/*------------------------------------ - EXTRUDER SETTINGS - *------------------------------------*/ - -// Mintemps -#define HEATER_0_MINTEMP 15 -#define HEATER_1_MINTEMP 5 -#define HEATER_2_MINTEMP 5 -#define BED_MINTEMP 15 - -// Maxtemps -#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP) -#define HEATER_0_MAXTEMP 410 -#else -#define HEATER_0_MAXTEMP 305 -#endif -#define HEATER_1_MAXTEMP 305 -#define HEATER_2_MAXTEMP 305 -#define BED_MAXTEMP 150 - -#if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP) -// Define PID constants for extruder with PT100 -#define DEFAULT_Kp 21.70 -#define DEFAULT_Ki 1.60 -#define DEFAULT_Kd 73.76 -#else -// Define PID constants for extruder -//#define DEFAULT_Kp 40.925 -//#define DEFAULT_Ki 4.875 -//#define DEFAULT_Kd 86.085 -#define DEFAULT_Kp 16.13 -#define DEFAULT_Ki 1.1625 -#define DEFAULT_Kd 56.23 -#endif - -// Extrude mintemp -#define EXTRUDE_MINTEMP 130 - -// Extruder cooling fans -#define EXTRUDER_0_AUTO_FAN_PIN 8 -#define EXTRUDER_1_AUTO_FAN_PIN -1 -#define EXTRUDER_2_AUTO_FAN_PIN -1 -#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 -#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed - - - -/*------------------------------------ - LOAD/UNLOAD FILAMENT SETTINGS - *------------------------------------*/ - -// Load filament commands -#define LOAD_FILAMENT_0 "M83" -#define LOAD_FILAMENT_1 "G1 E70 F400" -#define LOAD_FILAMENT_2 "G1 E40 F100" - -// Unload filament commands -#define UNLOAD_FILAMENT_0 "M83" -#define UNLOAD_FILAMENT_1 "G1 E-80 F7000" - -/*------------------------------------ - CHANGE FILAMENT SETTINGS - *------------------------------------*/ - -// Filament change configuration -#define FILAMENTCHANGEENABLE -#ifdef FILAMENTCHANGEENABLE -#define FILAMENTCHANGE_XPOS 211 -#define FILAMENTCHANGE_YPOS 0 -#define FILAMENTCHANGE_ZADD 2 -#define FILAMENTCHANGE_FIRSTRETRACT -2 -#define FILAMENTCHANGE_FINALRETRACT -80 - -#define FILAMENTCHANGE_FIRSTFEED 70 -#define FILAMENTCHANGE_FINALFEED 50 -#define FILAMENTCHANGE_RECFEED 5 - -#define FILAMENTCHANGE_XYFEED 50 -#define FILAMENTCHANGE_EFEED 20 -//#define FILAMENTCHANGE_RFEED 400 -#define FILAMENTCHANGE_RFEED 7000 / 60 -#define FILAMENTCHANGE_EXFEED 2 -#define FILAMENTCHANGE_ZFEED 15 - -#endif - -/*------------------------------------ - ADDITIONAL FEATURES SETTINGS - *------------------------------------*/ - -// Define Prusa filament runout sensor -//#define FILAMENT_RUNOUT_SUPPORT - -#ifdef FILAMENT_RUNOUT_SUPPORT -#define FILAMENT_RUNOUT_SENSOR 1 -#endif - -// temperature runaway -//#define TEMP_RUNAWAY_BED_HYSTERESIS 5 -//#define TEMP_RUNAWAY_BED_TIMEOUT 360 - -#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15 -#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45 - -/*------------------------------------ - MOTOR CURRENT SETTINGS - *------------------------------------*/ - -// Motor Current setting for BIG RAMBo -#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) -#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135} - -// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range -#if MOTHERBOARD == 200 || MOTHERBOARD == 203 || MOTHERBOARD == 303 || MOTHERBOARD == 304 || MOTHERBOARD == 305 -#define MOTOR_CURRENT_PWM_RANGE 2000 -#define DEFAULT_PWM_MOTOR_CURRENT {400, 750, 750} // {XY,Z,E} -#define DEFAULT_PWM_MOTOR_CURRENT_LOUD {400, 750, 750} // {XY,Z,E} -#endif - -/*------------------------------------ - BED SETTINGS - *------------------------------------*/ - -// Define Mesh Bed Leveling system to enable it -#define MESH_BED_LEVELING -#ifdef MESH_BED_LEVELING - -#define MBL_Z_STEP 0.01 - -// Mesh definitions -#define MESH_MIN_X 35 -#define MESH_MAX_X 238 -#define MESH_MIN_Y 6 -#define MESH_MAX_Y 202 - -// Mesh upsample definition -#define MESH_NUM_X_POINTS 7 -#define MESH_NUM_Y_POINTS 7 -// Mesh measure definition -#define MESH_MEAS_NUM_X_POINTS 3 -#define MESH_MEAS_NUM_Y_POINTS 3 - -#define MESH_HOME_Z_CALIB 0.2 -#define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc. - -#define X_PROBE_OFFSET_FROM_EXTRUDER 23 // Z probe to nozzle X offset: -left +right -#define Y_PROBE_OFFSET_FROM_EXTRUDER 9 // Z probe to nozzle Y offset: -front +behind -#define Z_PROBE_OFFSET_FROM_EXTRUDER -0.4 // Z probe to nozzle Z offset: -below (always!) -#endif - -// Bed Temperature Control -// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis -// -// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. -// If your PID_dT above is the default, and correct for your hardware/configuration, that means 7.689Hz, -// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. -// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. -// If your configuration is significantly different than this and you don't understand the issues involved, you probably -// shouldn't use bed PID until someone else verifies your hardware works. -// If this is enabled, find your own PID constants below. -#define PIDTEMPBED -// -//#define BED_LIMIT_SWITCHING - -// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. -// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) -// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, -// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) -#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current - -// Bed temperature compensation settings -#define BED_OFFSET 10 -#define BED_OFFSET_START 40 -#define BED_OFFSET_CENTER 50 - - -#ifdef PIDTEMPBED -//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) -//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) -#if defined(E3D_PT100_BED_WITH_AMP) || defined(E3D_PT100_BED_NO_AMP) -// Define PID constants for extruder with PT100 -#define DEFAULT_bedKp 21.70 -#define DEFAULT_bedKi 1.60 -#define DEFAULT_bedKd 73.76 -#else -#define DEFAULT_bedKp 126.13 -#define DEFAULT_bedKi 4.30 -#define DEFAULT_bedKd 924.76 -#endif - -//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) -//from pidautotune -// #define DEFAULT_bedKp 97.1 -// #define DEFAULT_bedKi 1.41 -// #define DEFAULT_bedKd 1675.16 - -// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. -#endif // PIDTEMPBED - - -/*----------------------------------- - PREHEAT SETTINGS - *------------------------------------*/ - -#define PLA_PREHEAT_HOTEND_TEMP 215 -#define PLA_PREHEAT_HPB_TEMP 55 -#define PLA_PREHEAT_FAN_SPEED 0 - -#define ABS_PREHEAT_HOTEND_TEMP 255 -#define ABS_PREHEAT_HPB_TEMP 100 -#define ABS_PREHEAT_FAN_SPEED 0 - -#define HIPS_PREHEAT_HOTEND_TEMP 220 -#define HIPS_PREHEAT_HPB_TEMP 100 -#define HIPS_PREHEAT_FAN_SPEED 0 - -#define PP_PREHEAT_HOTEND_TEMP 254 -#define PP_PREHEAT_HPB_TEMP 100 -#define PP_PREHEAT_FAN_SPEED 0 - -#define PET_PREHEAT_HOTEND_TEMP 240 -#define PET_PREHEAT_HPB_TEMP 90 -#define PET_PREHEAT_FAN_SPEED 0 - -#define FLEX_PREHEAT_HOTEND_TEMP 230 -#define FLEX_PREHEAT_HPB_TEMP 50 -#define FLEX_PREHEAT_FAN_SPEED 0 - -/*------------------------------------ - THERMISTORS SETTINGS - *------------------------------------*/ - -// -//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table -// -//// Temperature sensor settings: -// -2 is thermocouple with MAX6675 (only for sensor 0) -// -1 is thermocouple with AD595 -// 0 is not used -// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) -// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) -// 3 is Mendel-parts thermistor (4.7k pullup) -// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! -// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) -// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) -// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) -// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) -// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) -// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) -// 10 is 100k RS thermistor 198-961 (4.7k pullup) -// 11 is 100k beta 3950 1% thermistor (4.7k pullup) -// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) -// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" -// 20 is the PT100 circuit found in the Ultimainboard V2.x -// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 -// -// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k -// (but gives greater accuracy and more stable PID) -// 51 is 100k thermistor - EPCOS (1k pullup) -// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) -// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) -// -// 1047 is Pt1000 with 4k7 pullup -// 1010 is Pt1000 with 1k pullup (non standard) -// 147 is Pt100 with 4k7 pullup -// 148 is E3D Pt100 with 4k7 pullup and no PT100 Amplifier on a MiniRambo 1.3a -// 247 is Pt100 with 4k7 pullup and PT100 Amplifier -// 110 is Pt100 with 1k pullup (non standard) - -#if defined(E3D_PT100_EXTRUDER_WITH_AMP) -#define TEMP_SENSOR_0 247 -#elif defined(E3D_PT100_EXTRUDER_NO_AMP) -#define TEMP_SENSOR_0 148 -#else -#define TEMP_SENSOR_0 5 -#endif -#define TEMP_SENSOR_1 0 -#define TEMP_SENSOR_2 0 -#if defined(E3D_PT100_BED_WITH_AMP) -#define TEMP_SENSOR_BED 247 -#elif defined(E3D_PT100_BED_NO_AMP) -#define TEMP_SENSOR_BED 148 -#else -#define TEMP_SENSOR_BED 1 -#endif -#define TEMP_SENSOR_PINDA 1 -#define TEMP_SENSOR_AMBIENT 2000 - -#define STACK_GUARD_TEST_VALUE 0xA2A2 - -#define MAX_BED_TEMP_CALIBRATION 50 -#define MAX_HOTEND_TEMP_CALIBRATION 50 - -#define MAX_E_STEPS_PER_UNIT 250 -#define MIN_E_STEPS_PER_UNIT 100 - -#define Z_BABYSTEP_MIN -3999 -#define Z_BABYSTEP_MAX 0 - -#define PINDA_PREHEAT_X 70 -#define PINDA_PREHEAT_Y -3 -#define PINDA_PREHEAT_Z 1 -#define PINDA_HEAT_T 120 //time in s - -#define PINDA_MIN_T 50 -#define PINDA_STEP_T 10 -#define PINDA_MAX_T 100 - -#define PING_TIME 60 //time in s -#define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid false triggering when dealing with long gcodes -#define PING_ALLERT_PERIOD 60 //time in s - -#define LONG_PRESS_TIME 1000 //time in ms for button long press -#define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release - -#define DEFAULT_PID_TEMP 210 - -#define MIN_PRINT_FAN_SPEED 75 - -#ifdef SNMM -#define DEFAULT_RETRACTION 4 //used for PINDA temp calibration and pause print -#else -#define DEFAULT_RETRACTION 1 //used for PINDA temp calibration and pause print -#endif - -// How much shall the print head be lifted on power panic? -// Ideally the Z axis will reach a zero phase of the stepper driver on power outage. To simplify this, -// UVLO_Z_AXIS_SHIFT shall be an integer multiply of the stepper driver cycle, that is 4x full step. -// For example, the Prusa i3 MK2 with 16 microsteps per full step has Z stepping of 400 microsteps per mm. -// At 400 microsteps per mm, a full step lifts the Z axis by 0.04mm, and a stepper driver cycle is 0.16mm. -// The following example, 12 * (4 * 16 / 400) = 12 * 0.16mm = 1.92mm. -#define UVLO_Z_AXIS_SHIFT 1.92 -// If power panic occured, and the current temperature is higher then target temperature before interrupt minus this offset, print will be recovered automatically. -#define AUTOMATIC_UVLO_BED_TEMP_OFFSET 5 - -#define HEATBED_V2 - -//#define SUPPORT_VERBOSITY - -#endif //__CONFIGURATION_PRUSA_H diff --git a/Firmware/variants/3mm-RAMBo10a-PrusaNmk2.h b/Firmware/variants/3mm-RAMBo10a-PrusaNmk2.h deleted file mode 100644 index de074c54..00000000 --- a/Firmware/variants/3mm-RAMBo10a-PrusaNmk2.h +++ /dev/null @@ -1,247 +0,0 @@ -#ifndef CONFIGURATION_PRUSA_H -#define CONFIGURATION_PRUSA_H - -/*------------------------------------ - GENERAL SETTINGS -*------------------------------------*/ - -// Printer revision -#define FILAMENT_SIZE "3mm" -#define NOZZLE_TYPE "PrusaNmk2" -#define THREEMM_PRINTER - -// Printer name -#define CUSTOM_MENDEL_NAME "Prusa i3" - -// Electronics -#define MOTHERBOARD BOARD_RAMBO_MINI_1_0 - - - -/*------------------------------------ - AXIS SETTINGS -*------------------------------------*/ - -// Steps per unit {X,Y,Z,E} -#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/0.8,350*1.5} - -// Endstop inverting -const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. - -// Home position -#define MANUAL_X_HOME_POS 0 -#define MANUAL_Y_HOME_POS 0 -#define MANUAL_Z_HOME_POS 0.25 - -// Travel limits after homing -#define X_MAX_POS 214 -#define X_MIN_POS 0 -#define Y_MAX_POS 198 -#define Y_MIN_POS 0 -#define Z_MAX_POS 201 -#define Z_MIN_POS 0.23 - -// Canceled home position -#define X_CANCEL_POS 50 -#define Y_CANCEL_POS 180 - - -#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E -#define HOMING_FEEDRATE {3000, 3000, 240, 0} // set the homing speeds (mm/min) - -#define DEFAULT_MAX_FEEDRATE {500, 500, 3, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,30,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts - - -#define MANUAL_FEEDRATE {3000, 3000, 240, 60} // set the speeds for manual moves (mm/min) - - -/*------------------------------------ - EXTRUDER SETTINGS -*------------------------------------*/ - -// Mintemps -#define HEATER_0_MINTEMP 15 -#define HEATER_1_MINTEMP 5 -#define HEATER_2_MINTEMP 5 -#define BED_MINTEMP 15 - -// Maxtemps -#define HEATER_0_MAXTEMP 315 -#define HEATER_1_MAXTEMP 275 -#define HEATER_2_MAXTEMP 275 -#define BED_MAXTEMP 150 - -// Define PID constants for extruder -#define DEFAULT_Kp 12.7 -#define DEFAULT_Ki 1.09 -#define DEFAULT_Kd 37.4 - -// Extrude mintemp -#define EXTRUDE_MINTEMP 130 - -// Extruder cooling fans -#define EXTRUDER_0_AUTO_FAN_PIN 6 -#define EXTRUDER_1_AUTO_FAN_PIN -1 -#define EXTRUDER_2_AUTO_FAN_PIN -1 -#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 -#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed - - - -/*------------------------------------ - LOAD/UNLOAD FILAMENT SETTINGS -*------------------------------------*/ - -// Load filament commands -#define LOAD_FILAMENT_0 "M83" -#define LOAD_FILAMENT_1 "G1 E65 F400" -#define LOAD_FILAMENT_2 "G1 E40 F100" - -// Unload filament commands -#define UNLOAD_FILAMENT_0 "M83" -#define UNLOAD_FILAMENT_1 "G1 E-80 F400" - -/*------------------------------------ - CHANGE FILAMENT SETTINGS -*------------------------------------*/ - -// Filament change configuration -#define FILAMENTCHANGEENABLE - #ifdef FILAMENTCHANGEENABLE - #define FILAMENTCHANGE_XPOS 211 - #define FILAMENTCHANGE_YPOS 0 - #define FILAMENTCHANGE_ZADD 2 - #define FILAMENTCHANGE_FIRSTRETRACT -2 - #define FILAMENTCHANGE_FINALRETRACT -80 - - #define FILAMENTCHANGE_FIRSTFEED 70 - #define FILAMENTCHANGE_FINALFEED 50 - #define FILAMENTCHANGE_RECFEED 5 - - #define FILAMENTCHANGE_XYFEED 70 - #define FILAMENTCHANGE_EFEED 20 - #define FILAMENTCHANGE_RFEED 400 - #define FILAMENTCHANGE_EXFEED 2 - #define FILAMENTCHANGE_ZFEED 300 - -#endif - -/*------------------------------------ - ADDITIONAL FEATURES SETTINGS -*------------------------------------*/ - -// Define Prusa filament runout sensor -//#define FILAMENT_RUNOUT_SUPPORT - -#ifdef FILAMENT_RUNOUT_SUPPORT - #define FILAMENT_RUNOUT_SENSOR 1 -#endif - -/*------------------------------------ - MOTOR CURRENT SETTINGS -*------------------------------------*/ - -// Motor Current setting for BIG RAMBo -#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) -#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135} - -// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range -#if MOTHERBOARD == 102 || MOTHERBOARD == 302 - #define MOTOR_CURRENT_PWM_RANGE 2000 - #define DEFAULT_PWM_MOTOR_CURRENT {270, 450, 850} // {XY,Z,E} - #define DEFAULT_PWM_MOTOR_CURRENT_LOUD {540, 450, 500} // {XY,Z,E} -#endif - -/*------------------------------------ - PREHEAT SETTINGS -*------------------------------------*/ - -#define PLA_PREHEAT_HOTEND_TEMP 220 -#define PLA_PREHEAT_HPB_TEMP 50 -#define PLA_PREHEAT_FAN_SPEED 255 - -#define ABS_PREHEAT_HOTEND_TEMP 285 -#define ABS_PREHEAT_HPB_TEMP 100 -#define ABS_PREHEAT_FAN_SPEED 255 - -#define HIPS_PREHEAT_HOTEND_TEMP 220 -#define HIPS_PREHEAT_HPB_TEMP 100 -#define HIPS_PREHEAT_FAN_SPEED 0 - -#define PP_PREHEAT_HOTEND_TEMP 254 -#define PP_PREHEAT_HPB_TEMP 100 -#define PP_PREHEAT_FAN_SPEED 0 - -#define PET_PREHEAT_HOTEND_TEMP 240 -#define PET_PREHEAT_HPB_TEMP 90 -#define PET_PREHEAT_FAN_SPEED 0 - -#define FLEX_PREHEAT_HOTEND_TEMP 250 -#define FLEX_PREHEAT_HPB_TEMP 50 -#define FLEX_PREHEAT_FAN_SPEED 0 - -// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. -// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) -// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, -// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) -#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current - -// temperature runaway -//#define TEMP_RUNAWAY_BED_HYSTERESIS 5 -//#define TEMP_RUNAWAY_BED_TIMEOUT 360 - -#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15 -#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45 - -/*------------------------------------ - THERMISTORS SETTINGS -*------------------------------------*/ - -// -//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table -// -//// Temperature sensor settings: -// -2 is thermocouple with MAX6675 (only for sensor 0) -// -1 is thermocouple with AD595 -// 0 is not used -// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) -// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) -// 3 is Mendel-parts thermistor (4.7k pullup) -// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! -// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) -// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) -// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) -// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) -// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) -// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) -// 10 is 100k RS thermistor 198-961 (4.7k pullup) -// 11 is 100k beta 3950 1% thermistor (4.7k pullup) -// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) -// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" -// 20 is the PT100 circuit found in the Ultimainboard V2.x -// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 -// -// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k -// (but gives greater accuracy and more stable PID) -// 51 is 100k thermistor - EPCOS (1k pullup) -// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) -// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) -// -// 1047 is Pt1000 with 4k7 pullup -// 1010 is Pt1000 with 1k pullup (non standard) -// 147 is Pt100 with 4k7 pullup -// 110 is Pt100 with 1k pullup (non standard) - -#define TEMP_SENSOR_0 1 -#define TEMP_SENSOR_1 0 -#define TEMP_SENSOR_2 0 -#define TEMP_SENSOR_BED 1 - - -#endif //__CONFIGURATION_PRUSA_H diff --git a/Firmware/variants/3mm-RAMBo13a-PrusaNmk2.h b/Firmware/variants/3mm-RAMBo13a-PrusaNmk2.h deleted file mode 100644 index ffb0af44..00000000 --- a/Firmware/variants/3mm-RAMBo13a-PrusaNmk2.h +++ /dev/null @@ -1,246 +0,0 @@ -#ifndef CONFIGURATION_PRUSA_H -#define CONFIGURATION_PRUSA_H - -/*------------------------------------ - GENERAL SETTINGS -*------------------------------------*/ - -// Printer revision -#define FILAMENT_SIZE "3mm" -#define NOZZLE_TYPE "PrusaNmk2" -#define THREEMM_PRINTER - -// Printer name -#define CUSTOM_MENDEL_NAME "Prusa i3" - -// Electronics -#define MOTHERBOARD BOARD_RAMBO_MINI_1_3 - - - -/*------------------------------------ - AXIS SETTINGS -*------------------------------------*/ - -// Steps per unit {X,Y,Z,E} -#define DEFAULT_AXIS_STEPS_PER_UNIT {100,100,3200/0.8,350*1.5} - -// Endstop inverting -const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. - -// Home position -#define MANUAL_X_HOME_POS 0 -#define MANUAL_Y_HOME_POS 0 -#define MANUAL_Z_HOME_POS 0.25 - -// Travel limits after homing -#define X_MAX_POS 214 -#define X_MIN_POS 0 -#define Y_MAX_POS 198 -#define Y_MIN_POS 0 -#define Z_MAX_POS 201 -#define Z_MIN_POS 0.23 - -// Canceled home position -#define X_CANCEL_POS 50 -#define Y_CANCEL_POS 180 - -#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E -#define HOMING_FEEDRATE {3000, 3000, 240, 0} // set the homing speeds (mm/min) - -#define DEFAULT_MAX_FEEDRATE {500, 500, 3, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {9000,9000,30,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts - - -#define MANUAL_FEEDRATE {3000, 3000, 240, 60} // set the speeds for manual moves (mm/min) - - -/*------------------------------------ - EXTRUDER SETTINGS -*------------------------------------*/ - -// Mintemps -#define HEATER_0_MINTEMP 15 -#define HEATER_1_MINTEMP 5 -#define HEATER_2_MINTEMP 5 -#define BED_MINTEMP 15 - -// Maxtemps -#define HEATER_0_MAXTEMP 315 -#define HEATER_1_MAXTEMP 275 -#define HEATER_2_MAXTEMP 275 -#define BED_MAXTEMP 150 - -// Define PID constants for extruder -#define DEFAULT_Kp 12.7 -#define DEFAULT_Ki 1.09 -#define DEFAULT_Kd 37.4 - -// Extrude mintemp -#define EXTRUDE_MINTEMP 130 - -// Extruder cooling fans -#define EXTRUDER_0_AUTO_FAN_PIN 6 -#define EXTRUDER_1_AUTO_FAN_PIN -1 -#define EXTRUDER_2_AUTO_FAN_PIN -1 -#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 -#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed - - - -/*------------------------------------ - LOAD/UNLOAD FILAMENT SETTINGS -*------------------------------------*/ - -// Load filament commands -#define LOAD_FILAMENT_0 "M83" -#define LOAD_FILAMENT_1 "G1 E65 F400" -#define LOAD_FILAMENT_2 "G1 E40 F100" - -// Unload filament commands -#define UNLOAD_FILAMENT_0 "M83" -#define UNLOAD_FILAMENT_1 "G1 E-80 F400" - -/*------------------------------------ - CHANGE FILAMENT SETTINGS -*------------------------------------*/ - -// Filament change configuration -#define FILAMENTCHANGEENABLE - #ifdef FILAMENTCHANGEENABLE - #define FILAMENTCHANGE_XPOS 211 - #define FILAMENTCHANGE_YPOS 0 - #define FILAMENTCHANGE_ZADD 2 - #define FILAMENTCHANGE_FIRSTRETRACT -2 - #define FILAMENTCHANGE_FINALRETRACT -80 - - #define FILAMENTCHANGE_FIRSTFEED 70 - #define FILAMENTCHANGE_FINALFEED 50 - #define FILAMENTCHANGE_RECFEED 5 - - #define FILAMENTCHANGE_XYFEED 70 - #define FILAMENTCHANGE_EFEED 20 - #define FILAMENTCHANGE_RFEED 400 - #define FILAMENTCHANGE_EXFEED 2 - #define FILAMENTCHANGE_ZFEED 300 - -#endif - -/*------------------------------------ - ADDITIONAL FEATURES SETTINGS -*------------------------------------*/ - -// Define Prusa filament runout sensor -//#define FILAMENT_RUNOUT_SUPPORT - -#ifdef FILAMENT_RUNOUT_SUPPORT - #define FILAMENT_RUNOUT_SENSOR 1 -#endif - -/*------------------------------------ - MOTOR CURRENT SETTINGS -*------------------------------------*/ - -// Motor Current setting for BIG RAMBo -#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) -#define DIGIPOT_MOTOR_CURRENT_LOUD {135,135,135,135,135} - -// Motor Current settings for RAMBo mini PWM value = MotorCurrentSetting * 255 / range -#if MOTHERBOARD == 102 || MOTHERBOARD == 302 - #define MOTOR_CURRENT_PWM_RANGE 2000 - #define DEFAULT_PWM_MOTOR_CURRENT {270, 450, 850} // {XY,Z,E} - #define DEFAULT_PWM_MOTOR_CURRENT_LOUD {540, 450, 500} // {XY,Z,E} -#endif - -/*------------------------------------ - PREHEAT SETTINGS -*------------------------------------*/ - -#define PLA_PREHEAT_HOTEND_TEMP 220 -#define PLA_PREHEAT_HPB_TEMP 50 -#define PLA_PREHEAT_FAN_SPEED 255 - -#define ABS_PREHEAT_HOTEND_TEMP 285 -#define ABS_PREHEAT_HPB_TEMP 100 -#define ABS_PREHEAT_FAN_SPEED 255 - -#define HIPS_PREHEAT_HOTEND_TEMP 220 -#define HIPS_PREHEAT_HPB_TEMP 100 -#define HIPS_PREHEAT_FAN_SPEED 0 - -#define PP_PREHEAT_HOTEND_TEMP 254 -#define PP_PREHEAT_HPB_TEMP 100 -#define PP_PREHEAT_FAN_SPEED 0 - -#define PET_PREHEAT_HOTEND_TEMP 240 -#define PET_PREHEAT_HPB_TEMP 90 -#define PET_PREHEAT_FAN_SPEED 0 - -#define FLEX_PREHEAT_HOTEND_TEMP 250 -#define FLEX_PREHEAT_HPB_TEMP 50 -#define FLEX_PREHEAT_FAN_SPEED 0 - -// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. -// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) -// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, -// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) -#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current - -// temperature runaway -//#define TEMP_RUNAWAY_BED_HYSTERESIS 5 -//#define TEMP_RUNAWAY_BED_TIMEOUT 360 - -#define TEMP_RUNAWAY_EXTRUDER_HYSTERESIS 15 -#define TEMP_RUNAWAY_EXTRUDER_TIMEOUT 45 - -/*------------------------------------ - THERMISTORS SETTINGS -*------------------------------------*/ - -// -//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table -// -//// Temperature sensor settings: -// -2 is thermocouple with MAX6675 (only for sensor 0) -// -1 is thermocouple with AD595 -// 0 is not used -// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) -// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) -// 3 is Mendel-parts thermistor (4.7k pullup) -// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! -// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) -// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) -// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) -// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) -// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) -// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) -// 10 is 100k RS thermistor 198-961 (4.7k pullup) -// 11 is 100k beta 3950 1% thermistor (4.7k pullup) -// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) -// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" -// 20 is the PT100 circuit found in the Ultimainboard V2.x -// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 -// -// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k -// (but gives greater accuracy and more stable PID) -// 51 is 100k thermistor - EPCOS (1k pullup) -// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) -// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) -// -// 1047 is Pt1000 with 4k7 pullup -// 1010 is Pt1000 with 1k pullup (non standard) -// 147 is Pt100 with 4k7 pullup -// 110 is Pt100 with 1k pullup (non standard) - -#define TEMP_SENSOR_0 1 -#define TEMP_SENSOR_1 0 -#define TEMP_SENSOR_2 0 -#define TEMP_SENSOR_BED 1 - - -#endif //__CONFIGURATION_PRUSA_H