3DPrinting/Prusa-Firmware
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
762 Commits 3 Branches 78 Tags 40 MiB
27659ae69e
Commit Graph

762 Commits

This Branch
This Branch
All Branches
Author SHA1 Message Date
Robert Pelnar
530dfba417 Status message limit (PFW-124) 2018-01-12 21:21:21 +01:00
bubnikv
82304a2268 Slight optimization of the fan speed interrupt routine by accessing 
the Arduino millis() without locking interrupts.
 2018-01-12 21:16:29 +01:00
PavelSindler
b2e6779782
Merge pull request #394 from bubnikv/MK3 
Slight optimization of the stepper timer routine.
 2018-01-12 21:02:50 +01:00
Robert Pelnar
ebf6d08fae Crash detection - message on lcd (PFW-115) 2018-01-12 21:02:49 +01:00
bubnikv
135dda1bff Slight optimization of the stepper timer routine. 
Use WRITE_NC instead of WRITE for writing into the slow ports.
 2018-01-12 21:01:01 +01:00
PavelSindler
be341d9825
Merge pull request #393 from bubnikv/MK3 
Mk3
 2018-01-12 20:53:47 +01:00
bubnikv
3e6d853364 Debugging of the stepper timer routine. When enabled through 
DEBUG_STEPPER_TIMER_MISSED, the printer is halted on stepper timer overflow
and an error message is displayed.
 2018-01-12 20:51:14 +01:00
PavelSindler
23b78da2f5 filament fails counter fixed 2018-01-12 20:21:07 +01:00
bubnikv
26747d7236 Definition of 8 pins on the Einsy 0.4 board connected to pin headers 
to be monitored by an 8 channel logic analyzer, for example the Saleae.
 2018-01-12 20:18:20 +01:00
bubnikv
db985065ff WRITE_NC macro for non-critical (non-synchronized) access to 
slow ports. The WRITE macro stores the CPU bits on the stack first,
then locks the interupts, reads the port, sets a bit, writes the port
and then finally reverts the CPU bits. The WRITE_NC does not lock
the interrupts, therefore it may only be used where it cannot
be interrupted.
 2018-01-12 20:15:59 +01:00
PavelSindler
1fbed53200 initial 2018-01-12 20:01:22 +01:00
Robert Pelnar
0f46fa0c37 blocking messages in settings/tune menu (PFW104) 
switch normal/stealth (PFW110)
 2018-01-12 19:54:32 +01:00
PavelSindler
6643f77648
Merge pull request #390 from PavelSindler/MK3_for_merging 
commit nr updated
 2018-01-11 17:52:15 +01:00
PavelSindler
a4be2af538 commit nr updated 2018-01-11 17:51:30 +01:00
PavelSindler
f5ed12817d
Merge pull request #388 from PavelSindler/first_layer_saving 
Live adjust Z saving using timeout
 2018-01-11 17:49:40 +01:00
PavelSindler
5c1db284b0 remove setting live adjust status in setup function 2018-01-11 17:48:58 +01:00
PavelSindler
97bd56d560
Merge pull request #386 from PavelSindler/selftest_swapped_fans 
manual check for swapped fans
 2018-01-11 17:45:23 +01:00
bubnikv
52315d7382
Merge pull request #389 from PavelSindler/fw_versions 
development fw versions has initial message for warning
 2018-01-11 17:12:25 +01:00
bubnikv
c3179f6960
Merge branch 'MK3' into fw_versions 2018-01-11 17:12:17 +01:00
bubnikv
cfae8f859d
Merge branch 'MK3' into fw_versions 2018-01-11 16:58:47 +01:00
PavelSindler
087532085f development fw versions has initial message for warning 2018-01-11 15:50:26 +01:00
PavelSindler
cc20da62a8 whitespace 2018-01-10 23:31:06 +01:00
PavelSindler
c185b46eb2 live adjust Z saving using timeout 2018-01-10 23:28:41 +01:00
Robert Pelnar
0d269261e4 PFW-110 - load filament - beep when loading finished. 2018-01-10 18:50:16 +01:00
PavelSindler
c79d960cb5 manual check for swapped fans 2018-01-10 16:40:06 +01:00
XPila
6ff7641d97
Merge pull request #385 from XPila/MK3 
Build 143f
 2018-01-09 20:01:56 +01:00
Robert Pelnar
43010b30b4 Build 143f 
Crashdetection improoved, blocking temperature ISR fixed, limits for silent mode adjusted.
 2018-01-09 19:54:07 +01:00
PavelSindler
22f7e577c0
Merge pull request #384 from PavelSindler/MK3_for_merging 
thermal runaway: reset cmd queue
 2018-01-09 13:50:19 +01:00
PavelSindler
858945d949 thermal runaway: reset cmd queue to ensure that heater/bed temp will be always set to zero 2018-01-09 13:35:12 +01:00
PavelSindler
a672f5faad
Merge pull request #383 from PavelSindler/selftest_fix 
temp runaway for heatbed enabled in config
 2018-01-08 16:16:57 +01:00
PavelSindler
75efc71527 temp runaway for heatbed enabled in config 2018-01-08 16:15:50 +01:00
PavelSindler
3b5c960f12
Merge pull request #382 from PavelSindler/selftest_fix 
Fixed selftest error messages for print fan and extruder fan (were swapped)
 2018-01-08 16:11:03 +01:00
PavelSindler
b53197fdd1 Fixed error messages for print fan and extruder fan (were swapped) 2018-01-08 12:07:45 +01:00
XPila
f7d49a34fb
Merge pull request #369 from XPila/MK3 
build 143e
 2018-01-04 18:09:05 +01:00
Robert Pelnar
0a2087c1cb build 143e 
Linear advance disabled
Max feedrate reduced to 200mm/s
Silent max accel reduced to 984mm/s^2
some debug logs removed, tmc_init - log message fixed
 2018-01-04 18:08:22 +01:00
XPila
00698b00b6
Merge pull request #368 from XPila/MK3 
Missing serial characters debuging
 2018-01-02 20:56:11 +01:00
Robert Pelnar
8a5ba89a9c Missing serial characters debuging 
disabled fan ISR
disabled fsensor ISR
disabled linear advance
build 143b
 2018-01-02 20:55:33 +01:00
XPila
24f990820e
Merge pull request #363 from XPila/MK3 
Mk3
 2017-12-30 02:56:09 +01:00
Robert Pelnar
c6e77f55f6 checkrx in stepper returned back 
build 143a
 2017-12-30 02:55:22 +01:00
Robert Pelnar
568f03c46e build 143 2017-12-29 23:49:11 +01:00
Michal Průša
ff44fb5fb9
Merge pull request #361 from michalprusa/unload-tweak-lang 
Unload tweak lang
 2017-12-29 20:24:41 +01:00
Michal Průša
8d1f2afbf2 build number change 
just 141r -> 142
 2017-12-29 20:22:45 +01:00
Michal Průša
0920b62d80 build number change 2017-12-29 20:21:06 +01:00
Michal Průša
734639c1da Unload filament tweak 
unload filament now has longer and faster slow retract.
 2017-12-29 17:53:12 +01:00
Michal Průša
bbc7bba234
Merge pull request #359 from phildubach/MK3 
Issue #354: Turn off bed heater after temp calibration
 2017-12-29 10:45:30 +01:00
Phil Dubach
7fb1234855 Turn off bed heater after temp calibration 
After finishing the temperature calibration, turn off the bed heater
right away, before waiting for the user to acknowledge completion.
 2017-12-28 23:47:27 -08:00
XPila
07fe9abe44
Merge pull request #358 from XPila/MK3 
Serial communication uses port0 or port1, not both, removed some susp…
 2017-12-29 00:08:16 +01:00
Robert Pelnar
e3c006dbe9 Serial communication uses port0 or port1, not both, removed some suspected code. 
build 141
 2017-12-29 00:06:47 +01:00
XPila
8e63098504
Merge pull request #357 from michalprusa/panic-fix 
power panic polished
 2017-12-28 23:37:22 +01:00
Michal Průša
f71f133e80 power panic polished 
Retraction set correctly to have minimum missing line
Z motor current not lowered that drascialy
Extruder motor turning off instantly
Beeping added to the end
 2017-12-28 23:26:06 +01:00