PavelSindler
fbbcc27f1a
X max lowered to 250, XYZ/Z calibration: Z top coordinate changed, changes in xyz cal. because of stell sheet, still not final version
2017-11-12 11:30:06 +01:00
XPila
55325a5a32
Merge branch 'MK3' into MK3
2017-11-07 17:15:27 +01:00
PavelSindler
2e68770e62
initial version - messages missing (will not compile)
2017-11-07 16:49:04 +01:00
PavelSindler
67c76104a5
Configuration_prusa updated
2017-11-07 11:39:11 +01:00
Robert Pelnar
877c8a3978
TMC2130 configuration in eeprom (not finished).
...
Extruder and Z holding currents same as running currents.
M600 filament unload speed = 3500 (PFW-22).
FSensor - algorithm changed (reset error couter instead of decrement)
build number = 106
2017-10-30 15:45:29 +01:00
Robert Pelnar
cddb0eafb8
PAT9125 - sampled only Y value, new debug code D9125.
...
FSensor - synchronous sampling and new algorithm
build number = 103
2017-10-24 19:45:15 +02:00
michalprusa
84bdc6c0e6
Merge remote-tracking branch 'origin/MK3' into MK3
2017-10-18 15:36:31 +02:00
Robert Pelnar
66c19b874d
Extruder settings tunning ( http://jira.prusa/projects/PFW/issues/PFW-5 )
...
buildnumber increased to 101
2017-10-17 21:24:11 +02:00
Robert Pelnar
cc9f03a46f
Line endings to LF (./le.sh lf)
2017-10-03 13:01:59 +02:00
michalprusa
7cf0218737
Merge remote-tracking branch 'origin/MK3' into MK3
2017-09-27 21:34:37 +01:00
Robert Pelnar
cc469b4c51
changed configuration
2017-09-26 17:20:44 +02:00
michalprusa
0b88142253
Merge remote-tracking branch 'origin/MK3' into MK3
2017-09-26 14:48:32 +01:00
Robert Pelnar
ca33f7f60f
PWM_GRAD back to 4 (trinamic suggested value), standstilltimeout = 1000
2017-09-26 13:07:25 +02:00
michalprusa
5ff28682be
Automatic recovery after crash is detected
2017-09-26 11:48:46 +01:00
Robert Pelnar
40fae26d75
Silent / Hight Power mode switching - wait for standstill
...
parameter tunning:
PWM_GRAD, PWM_AMPL TCOOLTHRS (XY)
2017-09-26 12:22:58 +02:00
Robert Pelnar
345fee66be
Silent mode x-axis amplitude adjust from 200 to 210, because of layershift at high speed.
2017-09-26 07:20:54 +02:00
Robert Pelnar
b475d11bdb
Maker Faire brainstorm 2.0 (2)
...
Automatic recover after short power loss (according to heatbed temperature drop)
Adjusted crashdetection - TMC2130_TCOOLTHRS_X and TMC2130_TCOOLTHRS_Y = 450 to be enabled at low speed
!!!ALL FEATURES TESTED AT THIS POINT!!!
2017-09-26 06:11:42 +02:00
Robert Pelnar
89121e6e34
Maker Faire brainstorm 2.0
...
Added filament sensor and crash detection to EEPROM
Added crash-detection counters display disable directive
Added Restore/Save print directive
Added crash detection and filament sensor settings to Tune menu
2017-09-26 04:30:10 +02:00
Robert Pelnar
39f6e746dc
Crashdetection tunning.
2017-09-26 01:43:56 +02:00
bubnikv
ed0fe01bcc
Decreased the homing feedrate for the X axis from 3000 to 2500mm/min.
...
With the old settings the stall guard did not work reliably.
2017-09-25 15:22:20 +02:00
bubnikv
b0ca2477c8
Modified homing procedures for the X & Y axes using the Trinamic stall guard
...
to run against the end stop with a repeatable velocity.
Slightly reduced the collision detection sensitivity.
2017-09-24 00:07:32 +02:00
Robert Pelnar
480838a0a1
Fixed homing (mbl and babystep - crashdetection recovery work fine now).
2017-09-23 16:35:01 +02:00
Robert Pelnar
d2ff47dac8
Crashdetection
2017-09-22 23:06:52 +02:00
Robert Pelnar
4805713b8d
SG limits adjusted (x=5,y=5), for homing is possible to set different values (x=5,y=5, without filter).
2017-09-22 20:53:00 +02:00
Robert Pelnar
df1aa85526
Crashdetection + configuration file.
2017-09-22 19:28:32 +02:00
PavelSindler
6eb57da770
fan check can be turned off from support menu, saving parameters to eeprom with offset and different levels, fan kickstart,2nd heatbed version, fans check modified
2017-09-21 15:20:02 +02:00
Robert Pelnar
6f5f88e7ea
Temporary added configuration file Configuration_prusa.h.
2017-09-14 16:28:16 +02:00
