#ifndef PINS_H #define PINS_H #include "boards.h" #if !MB(5DPRINT) #define X_MS1_PIN -1 #define X_MS2_PIN -1 #define Y_MS1_PIN -1 #define Y_MS2_PIN -1 #define Z_MS1_PIN -1 #define Z_MS2_PIN -1 #define E0_MS1_PIN -1 #define E0_MS2_PIN -1 #define E1_MS1_PIN -1 #define E1_MS2_PIN -1 #define DIGIPOTSS_PIN -1 #endif #define LARGE_FLASH true /***************************************************************** * Rambo Pin Assignments 1.3 ******************************************************************/ #if MOTHERBOARD == 302 #define MINI_RAMBO #endif #if MOTHERBOARD == 301 || MOTHERBOARD == 302 #define KNOWN_BOARD #ifndef __AVR_ATmega2560__ #error Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu. #endif #define FR_SENS 21 #define X_STEP_PIN 37 #define X_DIR_PIN 48 #define X_MIN_PIN 12 #define X_MAX_PIN 30 #define X_ENABLE_PIN 29 #define X_MS1_PIN 40 #define X_MS2_PIN 41 #define Y_STEP_PIN 36 #define Y_DIR_PIN 49 #define Y_MIN_PIN 11 #define Y_MAX_PIN 24 #define Y_ENABLE_PIN 28 #define Y_MS1_PIN 69 #define Y_MS2_PIN 39 #define Z_STEP_PIN 35 #define Z_DIR_PIN 47 #define Z_MIN_PIN 10 #define Z_MAX_PIN 23 #define Z_ENABLE_PIN 27 #define Z_MS1_PIN 68 #define Z_MS2_PIN 67 #define TEMP_BED_PIN 2 #define TEMP_0_PIN 0 #define HEATER_1_PIN 7 #define TEMP_1_PIN 1 #define TEMP_2_PIN -1 #ifdef SNMM #define E_MUX0_PIN 17 #define E_MUX1_PIN 16 #define E_MUX2_PIN 84 #endif #ifdef DIS #define D_REQUIRE 30 #define D_DATA 20 #define D_DATACLOCK 21 #endif // The SDSS pin uses a different pin mapping from file Sd2PinMap.h #define SDSS 53 #ifndef SDSUPPORT // these pins are defined in the SD library if building with SD support #define SCK_PIN 52 #define MISO_PIN 50 #define MOSI_PIN 51 #endif #define BEEPER 84 #define BTN_EN1 72 #define BTN_EN2 14 #define BTN_ENC 9 #define SDCARDDETECT 15 #define LCD_PINS_RS 82 #define LCD_PINS_ENABLE 18 #define LCD_PINS_D4 19 #define LCD_PINS_D5 70 #define LCD_PINS_D6 85 #define LCD_PINS_D7 71 #define E0_STEP_PIN 34 #define E0_DIR_PIN 43 #define E0_ENABLE_PIN 26 #define E0_MS1_PIN 65 #define E0_MS2_PIN 66 #define LED_PIN 13 #ifdef THREEMM_PRINTER #define FAN_PIN 8 #else #define FAN_PIN 6 #endif #define KILL_PIN -1 //80 with Smart Controller LCD #define SUICIDE_PIN -1 //PIN that has to be turned on right after start, to keep power flowing. #define SDPOWER -1 #define HEATER_2_PIN -1 #ifdef MINI_RAMBO #define ELECTRONICS "RAMBo13a" #define HEATER_0_PIN 3 #define HEATER_BED_PIN 4 #define FAN_1_PIN -1 //6 #define PS_ON_PIN 71 #define MOTOR_CURRENT_PWM_XY_PIN 46 #define MOTOR_CURRENT_PWM_Z_PIN 45 #define MOTOR_CURRENT_PWM_E_PIN 44 #else //RAMBo #define ELECTRONICS "RAMBoBig" #define E1_STEP_PIN 33 #define E1_DIR_PIN 42 #define E1_ENABLE_PIN 25 #define E1_MS1_PIN 63 #define E1_MS2_PIN 64 #define DIGIPOTSS_PIN 38 #define DIGIPOT_CHANNELS {4,5,3,0,1} // X Y Z E0 E1 digipot channels to stepper driver mapping #define HEATER_0_PIN 9 #define HEATER_BED_PIN 3 #define PS_ON_PIN 4 #define SDSS 53 #ifdef ULTRA_LCD #define KILL_PIN 80 #ifdef NEWPANEL //arduino pin which triggers an piezzo beeper #define BEEPER 84 // Beeper on AUX-4 #define LCD_PINS_RS 82 #define LCD_PINS_ENABLE 18 #define LCD_PINS_D4 19 #define LCD_PINS_D5 70 #define LCD_PINS_D6 85 #define LCD_PINS_D7 71 //buttons are directly attached using AUX-2 #define BTN_EN1 76 #define BTN_EN2 77 #define BTN_ENC 78 //the click #define BLEN_C 2 #define BLEN_B 1 #define BLEN_A 0 #define SDCARDDETECT 81 // Ramps does not use this port //encoder rotation values #define encrot0 0 #define encrot1 2 #define encrot2 3 #define encrot3 1 #else //old style panel with shift register //arduino pin witch triggers an piezzo beeper #define BEEPER 84 //No Beeper added //buttons are attached to a shift register // Not wired this yet // #define SHIFT_CLK 38 // #define SHIFT_LD 42 // #define SHIFT_OUT 40 // #define SHIFT_EN 17 #define LCD_PINS_RS 82 #define LCD_PINS_ENABLE 18 #define LCD_PINS_D4 19 #define LCD_PINS_D5 70 #define LCD_PINS_D6 85 #define LCD_PINS_D7 71 //encoder rotation values #define encrot0 0 #define encrot1 2 #define encrot2 3 #define encrot3 1 //bits in the shift register that carry the buttons for: // left up center down right red #define BL_LE 7 #define BL_UP 6 #define BL_MI 5 #define BL_DW 4 #define BL_RI 3 #define BL_ST 2 #define BLEN_B 1 #define BLEN_A 0 #endif #endif //ULTRA_LCD #endif //RAMBo/MiniRambo option #endif /***************************************************************** * Rambo mini Pin Assignments 1.0 ******************************************************************/ #if MOTHERBOARD == 102 #define ELECTRONICS "RAMBo10a" #define KNOWN_BOARD #ifndef __AVR_ATmega2560__ #error Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu. #endif #define FR_SENS 21 #ifdef SNMM #define E_MUX0_PIN 17 #define E_MUX1_PIN 16 #define E_MUX2_PIN 84 #endif #define LARGE_FLASH true #define X_STEP_PIN 37 #define X_DIR_PIN 48 #define X_MIN_PIN 12 #define X_MAX_PIN 30 #define X_ENABLE_PIN 29 #define X_MS1_PIN 40 #define X_MS2_PIN 41 #define Y_STEP_PIN 36 #define Y_DIR_PIN 49 #define Y_MIN_PIN 11 #define Y_MAX_PIN 24 #define Y_ENABLE_PIN 28 #define Y_MS1_PIN 69 #define Y_MS2_PIN 39 #define Z_STEP_PIN 35 #define Z_DIR_PIN 47 #define Z_MIN_PIN 10 #define Z_MAX_PIN 23 #define Z_ENABLE_PIN 27 #define Z_MS1_PIN 68 #define Z_MS2_PIN 67 #define TEMP_BED_PIN 2 #define TEMP_0_PIN 0 #define HEATER_1_PIN 7 #define TEMP_1_PIN 1 #define TEMP_2_PIN -1 // The SDSS pin uses a different pin mapping from file Sd2PinMap.h #define SDSS 53 #ifndef SDSUPPORT // these pins are defined in the SD library if building with SD support #define SCK_PIN 52 #define MISO_PIN 50 #define MOSI_PIN 51 #endif #define BEEPER 78 #define BTN_EN1 80 #define BTN_EN2 73 #define BTN_ENC 21 #define SDCARDDETECT 72 #define LCD_PINS_RS 38 #define LCD_PINS_ENABLE 5 #define LCD_PINS_D4 14 #define LCD_PINS_D5 15 #define LCD_PINS_D6 32 #define LCD_PINS_D7 31 #define E0_STEP_PIN 34 #define E0_DIR_PIN 43 #define E0_ENABLE_PIN 26 #define E0_MS1_PIN 65 #define E0_MS2_PIN 66 #define LED_PIN 13 #ifdef THREEMM_PRINTER #define FAN_PIN 8 #else #define FAN_PIN 6 #endif #define KILL_PIN -1 //80 with Smart Controller LCD #define SUICIDE_PIN -1 //PIN that has to be turned on right after start, to keep power flowing. #define SDPOWER -1 #define HEATER_2_PIN -1 #define HEATER_0_PIN 3 #define HEATER_BED_PIN 4 #define FAN_1_PIN -1 //6 #define PS_ON_PIN 71 #define MOTOR_CURRENT_PWM_XY_PIN 46 #define MOTOR_CURRENT_PWM_Z_PIN 45 #define MOTOR_CURRENT_PWM_E_PIN 44 #endif /***************************************************************** * EINY Rambo Pin Assignments 0.3a ******************************************************************/ #if MOTHERBOARD == 300 #define ELECTRONICS "EINY_03a" #define KNOWN_BOARD #ifndef __AVR_ATmega2560__ #error Oops! Make sure you have 'Arduino Mega 2560 or Rambo' selected from the 'Tools -> Boards' menu. #endif #define LARGE_FLASH true #define HAVE_TMC2130_DRIVERS #define X_STEP_PIN 37 #define X_DIR_PIN 49 #define X_MIN_PIN 12 #define X_MAX_PIN 30 #define X_ENABLE_PIN 29 #define X_MS1_PIN -1 #define X_MS2_PIN -1 #define X_TMC2130_CS 41 #define Y_STEP_PIN 36 #define Y_DIR_PIN 48 #define Y_MIN_PIN 11 #define Y_MAX_PIN 24 #define Y_ENABLE_PIN 28 #define Y_MS1_PIN -1 #define Y_MS2_PIN -1 #define Y_TMC2130_CS 39 #define Z_STEP_PIN 35 #define Z_DIR_PIN 47 #define Z_MIN_PIN 10 #define Z_MAX_PIN 23 #define Z_ENABLE_PIN 27 #define Z_MS1_PIN -1 #define Z_MS2_PIN -1 #define Z_TMC2130_CS 67 #define HEATER_BED_PIN 4 #define TEMP_BED_PIN 2 #define HEATER_0_PIN 3 #define TEMP_0_PIN 0 #define HEATER_1_PIN 7 #define TEMP_1_PIN 1 #ifdef BARICUDA #define HEATER_2_PIN 6 #else #define HEATER_2_PIN -1 #endif #define TEMP_2_PIN -1 #define E0_STEP_PIN 34 #define E0_DIR_PIN 43 #define E0_ENABLE_PIN 26 #define E0_MS1_PIN -1 #define E0_MS2_PIN -1 #define E0_TMC2130_CS 66 #define MOTOR_CURRENT_PWM_XY_PIN 46 #define MOTOR_CURRENT_PWM_Z_PIN 45 #define MOTOR_CURRENT_PWM_E_PIN 44 #define SDPOWER -1 #define SDSS 53 #define LED_PIN 13 #define FAN_PIN 6 #define FAN_1_PIN -1 #define PS_ON_PIN -1 #define KILL_PIN -1 // 80 with Smart Controller LCD #define SUICIDE_PIN -1 // PIN that has to be turned on right after start, to keep power flowing. #ifdef ULTRA_LCD #define KILL_PIN 32 #ifdef NEWPANEL #define BEEPER 84 // Beeper on AUX-4 #define LCD_PINS_RS 82 #define LCD_PINS_ENABLE 61 #define LCD_PINS_D4 59 #define LCD_PINS_D5 70 #define LCD_PINS_D6 85 #define LCD_PINS_D7 71 //buttons are directly attached using AUX-2 #define BTN_EN1 72 #define BTN_EN2 14 #define BTN_ENC 9 // the click #define SDCARDDETECT 15 #define TACH_0 79 #define TACH_1 80 #endif //NEWPANEL #endif //ULTRA_LCD #endif //MOTHERBOARD == 300 /***************************************************************** * EINY Rambo Pin Assignments 0.4a ******************************************************************/ #if MOTHERBOARD == 299 #define ELECTRONICS "EINY_04a" #define KNOWN_BOARD #ifndef __AVR_ATmega2560__ #error Oops! Make sure you have 'Arduino Mega 2560 or Rambo' selected from the 'Tools -> Boards' menu. #endif #define LARGE_FLASH true #define HAVE_TMC2130_DRIVERS #define X_STEP_PIN 37 #define X_DIR_PIN 49 #define X_MIN_PIN 12 #define X_MAX_PIN 30 #define X_ENABLE_PIN 29 #define X_MS1_PIN -1 #define X_MS2_PIN -1 #define X_TMC2130_CS 41 #define Y_STEP_PIN 36 #define Y_DIR_PIN 48 #define Y_MIN_PIN 11 #define Y_MAX_PIN 24 #define Y_ENABLE_PIN 28 #define Y_MS1_PIN -1 #define Y_MS2_PIN -1 #define Y_TMC2130_CS 39 #define Z_STEP_PIN 35 #define Z_DIR_PIN 47 #define Z_MIN_PIN 10 #define Z_MAX_PIN 23 #define Z_ENABLE_PIN 27 #define Z_MS1_PIN -1 #define Z_MS2_PIN -1 #define Z_TMC2130_CS 67 #define HEATER_BED_PIN 4 #define TEMP_BED_PIN 2 #define HEATER_0_PIN 3 #define TEMP_0_PIN 0 #define HEATER_1_PIN 7 #define TEMP_1_PIN 1 #ifdef BARICUDA #define HEATER_2_PIN 6 #else #define HEATER_2_PIN -1 #endif #define TEMP_2_PIN -1 #define E0_STEP_PIN 34 #define E0_DIR_PIN 43 #define E0_ENABLE_PIN 26 #define E0_MS1_PIN -1 #define E0_MS2_PIN -1 #define E0_TMC2130_CS 66 #define MOTOR_CURRENT_PWM_XY_PIN 46 #define MOTOR_CURRENT_PWM_Z_PIN 45 #define MOTOR_CURRENT_PWM_E_PIN 44 #define SDPOWER -1 #define SDSS 53 #define LED_PIN 13 #define FAN_PIN 6 #define FAN_1_PIN -1 #define PS_ON_PIN -1 #define KILL_PIN -1 // 80 with Smart Controller LCD #define SUICIDE_PIN -1 // PIN that has to be turned on right after start, to keep power flowing. #ifdef ULTRA_LCD #define KILL_PIN 32 #ifdef NEWPANEL #define BEEPER 84 // Beeper on AUX-4 #define LCD_PINS_RS 82 //#define LCD_PINS_ENABLE 18 //#define LCD_PINS_D4 19 #define LCD_PINS_ENABLE 61 #define LCD_PINS_D4 59 #define LCD_PINS_D5 70 #define LCD_PINS_D6 85 #define LCD_PINS_D7 71 //buttons are directly attached using AUX-2 #define BTN_EN1 72 #define BTN_EN2 14 #define BTN_ENC 9 // the click #define SDCARDDETECT 15 #define TACH_0 81 #define TACH_1 80 #endif //NEWPANEL #endif //ULTRA_LCD #endif //MOTHERBOARD == 300 #ifndef KNOWN_BOARD #error Unknown MOTHERBOARD value in configuration.h #endif //List of pins which to ignore when asked to change by gcode, 0 and 1 are RX and TX, do not mess with those! #define _E0_PINS E0_STEP_PIN, E0_DIR_PIN, E0_ENABLE_PIN, HEATER_0_PIN, #if EXTRUDERS > 1 #define _E1_PINS E1_STEP_PIN, E1_DIR_PIN, E1_ENABLE_PIN, HEATER_1_PIN, #else #define _E1_PINS #endif #if EXTRUDERS > 2 #define _E2_PINS E2_STEP_PIN, E2_DIR_PIN, E2_ENABLE_PIN, HEATER_2_PIN, #else #define _E2_PINS #endif #ifdef X_STOP_PIN #if X_HOME_DIR < 0 #define X_MIN_PIN X_STOP_PIN #define X_MAX_PIN -1 #else #define X_MIN_PIN -1 #define X_MAX_PIN X_STOP_PIN #endif #endif #ifdef Y_STOP_PIN #if Y_HOME_DIR < 0 #define Y_MIN_PIN Y_STOP_PIN #define Y_MAX_PIN -1 #else #define Y_MIN_PIN -1 #define Y_MAX_PIN Y_STOP_PIN #endif #endif #ifdef Z_STOP_PIN #if Z_HOME_DIR < 0 #define Z_MIN_PIN Z_STOP_PIN #define Z_MAX_PIN -1 #else #define Z_MIN_PIN -1 #define Z_MAX_PIN Z_STOP_PIN #endif #endif #ifdef DISABLE_MAX_ENDSTOPS #define X_MAX_PIN -1 #define Y_MAX_PIN -1 #define Z_MAX_PIN -1 #endif #ifdef DISABLE_MIN_ENDSTOPS #define X_MIN_PIN -1 #define Y_MIN_PIN -1 #define Z_MIN_PIN -1 #endif #define SENSITIVE_PINS {0, 1, X_STEP_PIN, X_DIR_PIN, X_ENABLE_PIN, X_MIN_PIN, X_MAX_PIN, Y_STEP_PIN, Y_DIR_PIN, Y_ENABLE_PIN, Y_MIN_PIN, Y_MAX_PIN, Z_STEP_PIN, Z_DIR_PIN, Z_ENABLE_PIN, Z_MIN_PIN, Z_MAX_PIN, PS_ON_PIN, \ HEATER_BED_PIN, FAN_PIN, \ _E0_PINS _E1_PINS _E2_PINS \ analogInputToDigitalPin(TEMP_0_PIN), analogInputToDigitalPin(TEMP_1_PIN), analogInputToDigitalPin(TEMP_2_PIN), analogInputToDigitalPin(TEMP_BED_PIN) } #endif //__PINS_H