/** * @file */ /** \ingroup eeprom_table */ //! _This is a EEPROM table of currently implemented in Prusa firmware (dynamically generated from doxygen)._ #ifndef EEPROM_H #define EEPROM_H #include #define MAX_SHEETS 8 #define MAX_SHEET_NAME_LENGTH 7 typedef struct { char name[MAX_SHEET_NAME_LENGTH]; //!< Can be null terminated, doesn't need to be null terminated int16_t z_offset; //!< Z_BABYSTEP_MIN .. Z_BABYSTEP_MAX = Z_BABYSTEP_MIN*2/1000 [mm] .. Z_BABYSTEP_MAX*2/1000 [mm] uint8_t bed_temp; //!< 0 .. 254 [°C] uint8_t pinda_temp; //!< 0 .. 254 [°C] } Sheet; typedef struct { Sheet s[MAX_SHEETS]; uint8_t active_sheet; } Sheets; // sizeof(Sheets). Do not change it unless EEPROM_Sheets_base is last item in EEPROM. // Otherwise it would move following items. #define EEPROM_SHEETS_SIZEOF 89 #ifdef __cplusplus static_assert(sizeof(Sheets) == EEPROM_SHEETS_SIZEOF, "Sizeof(Sheets) is not EEPROM_SHEETS_SIZEOF."); #endif /** @defgroup eeprom_table EEPROM Table * --------------------------------------------------------------------------------- EEPROM 8-bit Empty value = 0xFFh 255 EEPROM 16-bit Empty value = 0xFFFFh 65535 _Italic = unsued or default_ __Bold = Status__ --------------------------------------------------------------------------------- How can you use the debug codes? - Serial terminal like Putty. - Octoprint does support D-codes - _Pronterface_ does not support D-codes ### !!! D-codes are case sensitive so please don't use upper case A,C or X in the address you want to read !!! --------------------------------------------------------------------------------- | Adress begin | Bit/Type | Name | Valid values | Default/FactoryReset | Description | Gcode/Function| Debug code | :-- | :-- | :-- | :--: | :--: | :-- | :--: | :--: | 0x0FFFh 4095 | uchar | EEPROM_SILENT | 00h 0 | ffh 255 | TMC Stealth mode: __off__ / miniRambo Power mode | LCD menu | D3 Ax0fff C1 | ^ | ^ | ^ | 01h 1 | ^ | TMC Stealth mode: __on__ / miniRambo Silent mode | ^ | ^ | 0x0FFEh 4094 | uchar | EEPROM_LANG | 00h 0 | ffh 255 | English / LANG_ID_PRI | LCD menu | D3 Ax0ffe C1 | ^ | ^ | ^ | 01h 1 | ^ | Other language LANG_ID_SEC | ^ | ^ | 0x0FFCh 4092 | uint16 | EEPROM_BABYSTEP_X | ??? | ffh 255 | Babystep for X axis _unsued_ | ??? | D3 Ax0ffc C2 | 0x0FFAh 4090 | uint16 | EEPROM_BABYSTEP_Y | ??? | ffh 255 | Babystep for Y axis _unsued_ | ^ | D3 Ax0ffa C2 | 0x0FF8h 4088 | uint16 | EEPROM_BABYSTEP_Z | ??? | ffh 255 | Babystep for Z axis _lagacy_ | ^ | D3 Ax0ff8 C2 | ^ | ^ | ^ | ^ | ^ | multiple values stored now in EEPROM_Sheets_base | ^ | ^ | 0x0FF7h 4087 | uint8 | EEPROM_CALIBRATION_STATUS | 00h 0 | ffh 255 | Unknown | ??? | D3 Ax0ff7 C1 | ^ | ^ | ^ | 01h 1 | ^ | Calibrated | ^ | ^ | ^ | ^ | ^ | E6h 230 | ^ | needs Live Z adjustment | ^ | ^ | ^ | ^ | ^ | F0h 240 | ^ | needs Z calibration | ^ | ^ | ^ | ^ | ^ | FAh 250 | ^ | needs XYZ calibration | ^ | ^ | ^ | ^ | ^ | FFh 255 | ^ | Assbemled _default_ | ^ | ^ | 0x0FF5h 4085 | uint16 | EEPROM_BABYSTEP_Z0 | ??? | ??? | Babystep for Z ??? | ??? | D3 Ax0ff5 C2 | 0x0FF1h 4081 | uint32 | EEPROM_FILAMENTUSED | ??? | 00h 0 | Filament used in meters | ??? | D3 Ax0ff1 C4 | 0x0FEDh 4077 | uint32 | EEPROM_TOTALTIME | ??? | 00h 0 | Total print time | ??? | D3 Ax0fed C4 | 0x0FE5h 4069 | float | EEPROM_BED_CALIBRATION_CENTER | ??? | ??? | ??? | ??? | D3 Ax0fe5 C8 | ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^ | 0x0FDDh 4061 | float | EEPROM_BED_CALIBRATION_VEC_X | ??? | ??? | ??? | ??? | D3 Ax0fdd C8 | ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^ | 0x0FD5h 4053 | float | EEPROM_BED_CALIBRATION_VEC_Y | ??? | ??? | ??? | ??? | D3 Ax0fd5 C8 | ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^ | 0x0FC5h 4037 | int16 | EEPROM_BED_CALIBRATION_Z_JITTER | ??? | ??? | ??? | ??? | D3 Ax0fc5 C16 | ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^ | ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^ | ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^ | ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^ | ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^ | ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^ | ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^ | 0x0FC4h 4036 | bool | EEPROM_FARM_MODE | 00h 0 | ffh 255 | Prusa farm mode: __off__ | G99 | D3 Ax0fc4 C1 | ^ | ^ | ^ | 01h 1 | ^ | Prusa farm mode: __on__ | G98 | ^ | 0x0FC1h 4033 | int16 | EEPROM_FARM_NUMBER | ??? | ff ff ffh | Prusa farm number | ??? | D3 Ax0fc1 C3 | 0x0FC0h 4032 | bool | EEPROM_BED_CORRECTION_VALID | 00h 0 | 00h 0 | Bed correction invalid | ??? | D3 Ax0fc0 C1 | ^ | ^ | ^ | ffh 255 | | Bed correction valid | ??? | ^ | 0x0FBFh 4031 | char | EEPROM_BED_CORRECTION_LEFT | 00h FFh | 00h 0 | Bed manual correction left | LCD menu | D3 Ax0fbf C1 | ^ | ^ | ^ | ??? | ??? | At this moment limited to +-100um | G80 Lxxx | ^ | 0x0FBEh 4030 | char | EEPROM_BED_CORRECTION_RIGHT | 00h FFh | 00h 0 | Bed manual correction right | LCD menu | D3 Ax0fbe C1 | ^ | ^ | ^ | ??? | ??? | At this moment limited to +-100um | G80 Rxxx | ^ | 0x0FBDh 4029 | char | EEPROM_BED_CORRECTION_FRONT | 00h FFh | 00h 0 | Bed manual correction front | LCD menu | D3 Ax0fbd C1 | ^ | ^ | ^ | ??? | ??? | At this moment limited to +-100um | G80 Fxxx | ^ | 0x0FBCh 4028 | char | EEPROM_BED_CORRECTION_BACK | 00h FFh | 00h 0 | Bed manual correction back | LCD menu | D3 Ax0fbc C1 | ^ | ^ | ^ | ??? | ??? | At this moment limited to +-100um | G80 Bxxx | ^ | 0x0FBBh 4027 | bool | EEPROM_TOSHIBA_FLASH_AIR_COMPATIBLITY | 00h 0 | 00h 0 | Toshiba Air: __off__ | LCD menu | D3 Ax0fbb C1 | ^ | ^ | ^ | ??? | ffh 255 | Toshiba Air: __on__ | ^ | ^ | 0x0FBAh 4026 | uchar | EEPROM_PRINT_FLAG | ??? | ??? | _unsued_ | ??? | D3 Ax0fba C1 | 0x0FB0h 4016 | int16 | EEPROM_PROBE_TEMP_SHIFT | ??? | ??? | ??? | ??? | D3 Ax0fb0 C10 | ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^ | ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^ | ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^ | ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^ | 0x0FAFh 4015 | bool | EEPROM_TEMP_CAL_ACTIVE | 00h 0 | 00h 0 | PINDA Temp cal.: __inactive__ | LCD menu | D3 Ax0faf C1 | ^ | ^ | ^ | ffh 255 | ^ | PINDA Temp cal.: __active__ | ^ | ^ | 0x0FA7h 4007 | uint32 | EEPROM_BOWDEN_LENGTH | ??? | ff 00 ff ffh | Bowden length | ??? | D3 Ax0fae C8 | ^ | ^ | ^ | ??? | ff ff ff ffh | ^ | ^ | ^ | 0x0FA6h 4006 | uint8 | EEPROM_CALIBRATION_STATUS_PINDA | 00h 0 | ffh 255 | PINDA Temp: __not calibrated__ | ??? | D3 Ax0fa6 C1 | ^ | ^ | ^ | 01h 1 | ^ | PINDA Temp: __calibrated__ | ^ | ^ | 0x0FA5h 4005 | uint8 | EEPROM_UVLO | 00h 0 | ffh 255 | Power Panic flag: __inactive__ | ??? | D3 Ax0fa5 C1 | ^ | ^ | ^ | 01h 1 | ^ | Power Panic flag: __active__ | ^ | ^ | ^ | ^ | ^ | 02h 2 | ^ | Power Panic flag: __???__ | ^ | ^ | 0x0F9Dh 3997 | float | EEPROM_UVLO_CURRENT_POSITION | ??? | ffh 255 | Power Panic position | ??? | D3 Ax0f9d C8 | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | 0x0F95h 3989 | char | EEPROM_FILENAME | ??? | ffh 255 | Power Panic Filename | ??? | D3 Ax0f95 C8 | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | 0x0F91h 39851 | uint32 | EEPROM_FILE_POSITION | ??? | ff ff ff ffh | Power Panic File Postion | ??? | D3 Ax0f91 C4 | 0x0F8Dh 3981 | float | EEPROM_UVLO_CURRENT_POSITION_Z | ??? | ff ff ff ffh | Power Panic Z Position | ^ | D3 Ax0f8d C4 | 0x0F8Ch 3980 | ??? | EEPROM_UVLO_UNUSED_001 | ??? | ffh 255 | Power Panic _unused_ | ^ | D3 Ax0f8c C1 | 0x0F8Bh 3979 | uint8 | EEPROM_UVLO_TARGET_BED | ??? | ffh 255 | Power Panic Bed temperature | ^ | D3 Ax0f8b C1 | 0x0F89h 3977 | uint16 | EEPROM_UVLO_FEEDRATE | ??? | ff ffh 65535 | Power Panic Feedrate | ^ | D3 Ax0f89 C2 | 0x0F88h 3976 | uint8 | EEPROM_UVLO_FAN_SPEED | ??? | ffh 255 | Power Panic Fan speed | ^ | D3 Ax0f88 C1 | 0x0F87h 3975 | uint8 | EEPROM_FAN_CHECK_ENABLED | 00h 0 | ??? | Fan Check disabled | LCD menu | D3 Ax0f87 C1 | ^ | ^ | ^ | 01h 1 | ffh 255 | Fan Check enabled (exception ffh=01h) | ^ | ^ | 0x0F75h 3957 | uint16 | EEPROM_UVLO_MESH_BED_LEVELING | ??? | ff ffh 65535 | Power Panic Mesh Bed Leveling | ??? | D3 Ax0f75 C18 | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | 0x0F73h 3955 | uint16 | EEPROM_UVLO_Z_MICROSTEPS | ??? | ff ffh 65535 | Power Panic Z microsteps | ??? | D3 Ax0f73 C2 | 0x0F72h 3954 | uint8 | EEPROM_UVLO_E_ABS | ??? | ffh 255 | Power Panic ??? position | ??? | D3 Ax0f72 C1 | 0x0F6Eh 3950 | foat | EEPROM_UVLO_CURRENT_POSITION_E | ??? | ff ff ff ffh | Power Panic E position | ??? | D3 Ax0f6e C4 | 0x0F69h 3945 | uint8 | EEPROM_CRASH_DET | ffh 255 | ffh 255 | Crash detection: __enabled__ | LCD menu | D3 Ax0f69 C5 | ^ | ^ | ^ | 00h 0 | ^ | Crash detection: __disabled__ | LCD menu | ^ | ^ | ^ | ^ | ??? | ??? | ^ | ??? | ^ | ^ | ^ | ^ | ??? | ??? | ^ | ??? | ^ | ^ | ^ | ^ | ??? | ??? | ^ | ??? | ^ | 0x0F68h 3944 | uint8 | EEPROM_CRASH_COUNT_Y | 00h-ffh 0-255 | ffh 255 | Crashes detected on y axis | ??? | D3 Ax0f68 C1 | 0x0F67h 3943 | uint8 | EEPROM_FSENSOR | 01h 1 | ffh 255 | Filament sensor: __enabled__ | LCD menu | D3 Ax0f67 C1 | ^ | ^ | ^ | 00h 0 | ^ | Filament sensor: __disabled__ | LCD menu | ^ | 0x0F65h 3942 | uint8 | EEPROM_CRASH_COUNT_X | 00h-ffh 0-255 | ffh 255 | Crashes detected on x axis | ??? | D3 Ax0f66 C1 | 0x0F65h 3941 | uint8 | EEPROM_FERROR_COUNT | 00h-ffh 0-255 | ffh 255 | Filament sensor error counter | ??? | D3 Ax0f65 C1 | 0x0F64h 3940 | uint8 | EEPROM_POWER_COUNT | 00h-ffh 0-255 | ffh 255 | Power failure counter | ??? | D3 Ax0f64 C1 | 0x0F60h 3936 | float | EEPROM_XYZ_CAL_SKEW | ??? | ff ff ff ffh | XYZ skew value | ??? | D3 Ax0f60 C4 | 0x0F5Fh 3935 | uint8 | EEPROM_WIZARD_ACTIVE | 00h 0 | ??? | Wizard active | ??? | D3 Ax0f5f C1 | ^ | ^ | ^ | 01h 1 | ??? | ^ | ^ | ^ | 0x0F5Dh 3933 | uint16 | EEPROM_BELTSTATUS_X | ??? | ff ffh | X Beltstatus | ??? | D3 Ax0f5d C2 | 0x0F5Bh 3931 | uint16 | EEPROM_BELTSTATUS_Y | ??? | ff ffh | Y Beltstatus | ??? | D3 Ax0f5b C2 | 0x0F5Ah 3930 | uint8 | EEPROM_DIR_DEPTH | 00h-ffh 0-255 | ffh 255 | Directory depth | ??? | D3 Ax0f5a C1 | 0x0F0Ah 3850 | uint8 | EEPROM_DIRS | ??? | ffh 255 | Directories ??? | ??? | D3 Ax0f0a C80 | 0x0F09h 3849 | uint8 | EEPROM_SD_SORT | 00h 0 | ffh 255 | SD card sort by: __time__ | LCD menu | D3 Ax0f09 C1 | ^ | ^ | ^ | 01h 1 | ^ | SD card sort by: __alphabet__ | LCD menu | ^ | ^ | ^ | ^ | 02h 1 | ^ | SD card: __not sorted__ | LCD menu | ^ | 0x0F08h 3848 | uint8 | EEPROM_SECOND_SERIAL_ACTIVE | 00h 0 | ffh 255 | RPi Port: __disabled__ | LCD menu | D3 Ax0f08 C1 | ^ | ^ | ^ | 01h 1 | ^ | RPi Port: __enabled__ | LCD menu | ^ | 0x0F07h 3847 | uint8 | EEPROM_FSENS_AUTOLOAD_ENABLED | 01h 1 | ffh 255 | Filament autoload: __enabled__ | LCD menu | D3 Ax0f07 C1 | ^ | ^ | ^ | 00h 0 | ^ | Filament autoload: __disabled__ | LCD menu | ^ | 0x0F05h 3845 | uint16 | EEPROM_CRASH_COUNT_X_TOT | 0000-fffe | ff ffh | Total charshes on x axis | ??? | D3 Ax0f05 C2 | 0x0F03h 3843 | uint16 | EEPROM_CRASH_COUNT_Y_TOT | 0000-fffe | ff ffh | Total charshes on y axis | ??? | D3 Ax0f03 C2 | 0x0F01h 3841 | uint16 | EEPROM_FERROR_COUNT_TOT | 0000-fffe | ff ffh | Total filament sensor errors | ??? | D3 Ax0f01 C2 | 0x0EFFh 3839 | uint16 | EEPROM_POWER_COUNT_TOT | 0000-fffe | ff ffh | Total power failures | ??? | D3 Ax0eff C2 | 0x0EFEh 3838 | uint8 | EEPROM_TMC2130_HOME_X_ORIGIN | ??? | ffh 255 | ??? | ??? | D3 Ax0efe C1 | 0x0EFDh 3837 | uint8 | EEPROM MC2130_HOME_X_BSTEPS | ??? | ffh 255 | ??? | ??? | D3 Ax0efd C1 | 0x0EFCh 3836 | uint8 | EEPROM_TMC2130_HOME_X_FSTEPS | ??? | ffh 255 | ??? | ??? | D3 Ax0efc C1 | 0x0EFBh 3835 | uint8 | EEPROM_TMC2130_HOME_Y_ORIGIN | ??? | ffh 255 | ??? | ??? | D3 Ax0efb C1 | 0x0EFAh 3834 | uint8 | EEPROM_TMC2130_HOME_Y_BSTEPS | ??? | ffh 255 | ??? | ??? | D3 Ax0efa C1 | 0x0EF9h 3833 | uint8 | EEPROM_TMC2130_HOME_Y_FSTEPS | ??? | ffh 255 | ??? | ??? | D3 Ax0ef9 C1 | 0x0EF8h 3832 | uint8 | EEPROM_TMC2130_HOME_ENABLED | ??? | ffh 255 | ??? | ??? | D3 Ax0ef8 C1 | 0x0EF7h 3831 | uint8 | EEPROM_TMC2130_WAVE_X_FAC | ??? | ffh 255 | ??? | ??? | D3 Ax0ef7 C1 | 0x0EF6h 3830 | uint8 | EEPROM_TMC2130_WAVE_Y_FAC | ??? | ffh 255 | ??? | ??? | D3 Ax0ef6 C1 | 0x0EF5h 3829 | uint8 | EEPROM_TMC2130_WAVE_Z_FAC | ??? | ffh 255 | ??? | ??? | D3 Ax0ef5 C1 | 0x0EF4h 3828 | uint8 | EEPROM_TMC2130_WAVE_E_FAC | ??? | ffh 255 | ??? | ??? | D3 Ax0ef4 C1 | 0x0EF3h 3827 | uint8 | EEPROM_TMC2130_X_MRES | ??? | ffh 255 | ??? | ??? | D3 Ax0ef3 C1 | 0x0EF2h 3826 | uint8 | EEPROM_TMC2130_Y_MRES | ??? | ffh 255 | ??? | ??? | D3 Ax0ef2 C1 | 0x0EF1h 3825 | uint8 | EEPROM_TMC2130_Z_MRES | ??? | ffh 255 | ??? | ??? | D3 Ax0ef1 C1 | 0x0EF0h 3824 | uint8 | EEPROM_TMC2130_E_MRES | ??? | ffh 255 | ??? | ??? | D3 Ax0ef0 C1 | 0x0EEE 3822 | uint16 | EEPROM_PRINTER_TYPE | ??? | ff ffh 65535 | Printer Type | ??? | D3 Ax0eee C2 | 0x0EEC 3820 | uint16 | EEPROM_BOARD_TYPE | ??? | ff ffh 65535 | Board Type | ??? | D3 Ax0eec C2 | 0x0EE8 3816 | float | EEPROM_EXTRUDER_MULTIPLIER_0 | ??? | ff ff ff ffh | Power panic Extruder 0 multiplier | ??? | D3 Ax0ee8 C4 | 0x0EE4 3812 | float | EEPROM_EXTRUDER_MULTIPLIER_1 | ??? | ff ff ff ffh | Power panic Extruder 1 multiplier | ??? | D3 Ax0ee4 C4 | 0x0EE0 3808 | float | EEPROM_EXTRUDER_MULTIPLIER_2 | ??? | ff ff ff ffh | Power panic Extruder 2 multiplier | ??? | D3 Ax0ee0 C4 | 0x0EDE 3806 | uint16 | EEPROM_EXTRUDEMULTIPLY | ??? | ff ffh 65535 | Power panic Extruder multiplier | ??? | D3 Ax0ede C2 | 0x0EDA 3802 | float | EEPROM_UVLO_TINY_CURRENT_POSITION_Z | ??? | ff ff ff ffh | Power panic Z position | ??? | D3 Ax0eda C4 | 0x0ED8 3800 | uint16 | EEPROM_UVLO_TARGET_HOTEND | ??? | ff ffh 65535 | Power panic traget Hotend temperature | ??? | D3 Ax0ed8 C2 | 0x0ED7 3799 | uint8 | EEPROM_SOUND_MODE | 00h 0 | ffh 255 | Sound mode: __loud__ | ??? | D3 Ax0ed7 C1 | ^ | ^ | ^ | 01h 1 | ^ | Sound mode: __once__ | ^ | ^ | ^ | ^ | ^ | 02h 1 | ^ | Sound mode: __silent__ | ^ | ^ | ^ | ^ | ^ | 03h 1 | ^ | Sound mode: __assist__ | ^ | ^ | 0x0ED6 3798 | bool | EEPROM_AUTO_DEPLETE | 01h 1 | ffh 255 | MMU2/s autodeplete: __on__ | ??? | D3 Ax0ed6 C1 | ^ | ^ | ^ | 00h 0 | ^ | MMU2/s autodeplete: __off__ | ^ | ^ | 0x0ED5 3797 | bool | EEPROM_FSENS_OQ_MEASS_ENABLED | ??? | ffh 255 | PAT1925 ??? | ??? | D3 Ax0ed5 C1 | ^ | ^ | ^ | ??? | ^ | PAT1925 ??? | ^ | ^ | 0x0ED3 3795 | uint16 | EEPROM_MMU_FAIL_TOT | ??? | ff ffh 65535 | MMU2/s total failures | ??? | D3 Ax0ed3 C2 | 0x0ED2 3794 | uint8 | EEPROM_MMU_FAIL | ??? | ffh 255 | MMU2/s fails during print | ??? | D3 Ax0ed2 C1 | 0x0ED0 3792 | uint16 | EEPROM_MMU_LOAD_FAIL_TOT | ??? | ff ffh 65535 | MMU2/s total load failures | ??? | D3 Ax0ed0 C2 | 0x0ECF 3791 | uint8 | EEPROM_MMU_LOAD_FAIL | ??? | ffh 255 | MMU2/s load failures during print | ??? | D3 Ax0ecf C1 | 0x0ECE 3790 | uint8 | EEPROM_MMU_CUTTER_ENABLED | 00h 0 | ffh 255 | MMU2/s cutter: __disabled__ | LCD menu | D3 Ax0ece C1 | ^ | ^ | ^ | 01h 1 | ^ | MMU2/s cutter: __enabled__ | ^ | ^ | ^ | ^ | ^ | 02h 2 | ^ | MMU2/s cutter: __always__ | ^ | ^ | 0x0DAE 3502 | uint16 | EEPROM_UVLO_MESH_BED_LEVELING_FULL | ??? | ff ffh 65535 | Power panic Mesh bed leveling points | ??? | D3 Ax0dae C288 | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^ | 0x0DAD 3501 | uint8 | EEPROM_MBL_TYPE | ??? | ffh 255 | Mesh bed leveling precision _unused atm_ | ??? | D3 Ax0dad C1 | 0x0DAC 3500 | bool | EEPROM_MBL_MAGNET_ELIMINATION | 01h 1 | ffh 255 | Mesh bed leveling does: __ignores__ magnets | LCD menu | D3 Ax0dac C1 | ^ | ^ | ^ | 00h 0 | ^ | Mesh bed leveling does: __NOT ignores__ magnets | ^ | ^ | 0x0DAB 3499 | uint8 | EEPROM_MBL_POINTS_NR | 03h 3 | ffh 255 | Mesh bed leveling points: __3x3__ | LCD menu | D3 Ax0dab C1 | ^ | ^ | ^ | 07h 7 | ^ | Mesh bed leveling points: __7x7__ | ^ | ^ | 0x0DAA 3498 | uint8 | EEPROM_MBL_PROBE_NR | 03h 3 | ffh 255 | MBL times measurements for each point: __3__ | LCD menu | D3 Ax0daa C1 | ^ | ^ | ^ | 05h 5 | ^ | MBL times measurements for each point: __5__ | ^ | ^ | ^ | ^ | ^ | 01h 1 | ^ | MBL times measurements for each point: __7__ | ^ | ^ | 0x0DA9 3497 | uint8 | EEPROM_MMU_STEALTH | 01h 1 | ffh 255 | MMU2/s Silent mode: __on__ | ??? | D3 Ax0da9 C1 | ^ | ^ | ^ | 00h 0 | ^ | MMU2/s Silent mode: __off__ | ^ | ^ | 0x0DA8 3496 | uint8 | EEPROM_CHECK_MODE | 01h 1 | ffh 255 | Check mode for nozzle is: __warn__ | LCD menu | D3 Ax0da8 C1 | ^ | ^ | ^ | 02h 0 | ^ | Check mode for nozzle is: __strict__ | ^ | ^ | ^ | ^ | ^ | 00h 0 | ^ | Check mode for nozzle is: __none__ | ^ | ^ | 0x0DA7 3495 | uint8 | EEPROM_NOZZLE_DIAMETER | 28h 40 | ffh 255 | Nozzle diameter is: __40 or 0.40mm__ | LCD menu | D3 Ax0da7 C1 | ^ | ^ | ^ | 3ch 60 | ^ | Nozzle diameter is: __60 or 0.60mm__ | ^ | ^ | ^ | ^ | ^ | 19h 25 | ^ | Nozzle diameter is: __25 or 0.25mm__ | ^ | ^ | 0x0DA5 3493 | uint16 | EEPROM_NOZZLE_DIAMETER_uM | 9001h | ff ffh 65535 | Nozzle diameter is: __400um__ | LCD menu | D3 Ax0da5 C2 | ^ | ^ | ^ | 5802h | ^ | Nozzle diameter is: __600um__ | ^ | ^ | ^ | ^ | ^ | fa00h | ^ | Nozzle diameter is: __250um__ | ^ | ^ | 0x0DA4 3492 | uint8 | EEPROM_CHECK_MODEL | 01h 1 | ffh 255 | Check mode for printer model is: __warn__ | LCD menu | D3 Ax0da4 C1 | ^ | ^ | ^ | 02h 0 | ^ | Check mode for printer model is: __strict__ | ^ | ^ | ^ | ^ | ^ | 00h 0 | ^ | Check mode for printer model is: __none__ | ^ | ^ | 0x0DA3 3491 | uint8 | EEPROM_CHECK_VERSION | 01h 1 | ffh 255 | Check mode for firmware is: __warn__ | LCD menu | D3 Ax0da3 C1 | ^ | ^ | ^ | 02h 0 | ^ | Check mode for firmware is: __strict__ | ^ | ^ | ^ | ^ | ^ | 00h 0 | ^ | Check mode for firmware is: __none__ | ^ | ^ | 0x0DA2 3490 | uint8 | EEPROM_CHECK_GCODE | 01h 1 | ffh 255 | Check mode for gcode is: __warn__ _unused atm_ | LCD menu | D3 Ax0da2 C1 | ^ | ^ | ^ | 02h 0 | ^ | Check mode for gcode is: __strict__ _unused atm_ | ^ | ^ | ^ | ^ | ^ | 00h 0 | ^ | Check mode for gcode is: __none__ _unused atm_ | ^ | ^ | 0x0D49 3401 | uint16 | EEPROM_SHEETS_BASE | ??? | ffh 255 | ??? | LCD menu | D3 Ax0d49 C89 | 0x0D49 3401 | char | _1st Sheet block_ | 536d6f6f746831| ffffffffffffff | 1st sheet - Name: _Smooth1_ | ^ | D3 Ax0d49 C7 | 0x0D50 3408 | uint16 | ^ | 00 00h 0 | ff ffh 65535 | 1st sheet - Z offset | ^ | D3 Ax0d50 C2 | 0x0D52 3410 | uint8 | ^ | 00h 0 | ffh 255 | 1st sheet - bed temp | ^ | D3 Ax0d52 C1 | 0x0D53 3411 | uint8 | ^ | 00h 0 | ffh 255 | 1st sheet - PINDA temp | ^ | D3 Ax0d53 C1 | 0x0D54 3412 | char | _2nd Sheet block_ | 536d6f6f746832| ffffffffffffff | 2nd sheet - Name: _Smooth2_ | ^ | D3 Ax0d54 C7 | 0x0D5B 3419 | uint16 | ^ | 00 00h 0 | ff ffh 65535 | 2nd sheet - Z offset | ^ | D3 Ax0d5b C2 | 0x0D5D 3421 | uint8 | ^ | 00h 0 | ffh 255 | 2nd sheet - bed temp | ^ | D3 Ax0d5d C1 | 0x0D5E 3422 | uint8 | ^ | 00h 0 | ffh 255 | 2nd sheet - PINDA temp | ^ | D3 Ax0d5e C1 | 0x0D5F 3423 | char | _3rd Sheet block_ | 54657874757231| ffffffffffffff | 3rd sheet - Name: _Textur1_ | ^ | D3 Ax0d5f C7 | 0x0D66 3430 | uint16 | ^ | 00 00h 0 | ff ffh 65535 | 3rd sheet - Z offset | ^ | D3 Ax0d66 C2 | 0x0D68 3432 | uint8 | ^ | 00h 0 | ffh 255 | 3rd sheet - bed temp | ^ | D3 Ax0d68 C1 | 0x0D69 3433 | uint8 | ^ | 00h 0 | ffh 255 | 3rd sheet - PINDA temp | ^ | D3 Ax0d69 C1 | 0x0D6A 3434 | char | _4th Sheet block_ | 54657874757232| ffffffffffffff | 4th sheet - Name: _Textur2_ | ^ | D3 Ax0d6a C7 | 0x0D71 3441 | uint16 | ^ | 00 00h 0 | ff ffh 65535 | 4th sheet - Z offset | ^ | D3 Ax0d71 C2 | 0x0D73 3443 | uint8 | ^ | 00h 0 | ffh 255 | 4th sheet - bed temp | ^ | D3 Ax0d73 C1 | 0x0D74 3444 | uint8 | ^ | 00h 0 | ffh 255 | 4th sheet - PINDA temp | ^ | D3 Ax0d74 C1 | 0x0D75 3445 | char | _5th Sheet block_ | 437573746f6d31| ffffffffffffff | 5th sheet - Name: _Custom1_ | ^ | D3 Ax0d75 C7 | 0x0D7C 3452 | uint16 | ^ | 00 00h 0 | ff ffh 65535 | 5th sheet - Z offset | ^ | D3 Ax0d7c C2 | 0x0D7E 3454 | uint8 | ^ | 00h 0 | ffh 255 | 5th sheet - bed temp | ^ | D3 Ax0d7e C1 | 0x0D7F 3455 | uint8 | ^ | 00h 0 | ffh 255 | 5th sheet - PINDA temp | ^ | D3 Ax0d7f C1 | 0x0D80 3456 | char | _6th Sheet block_ | 437573746f6d32| ffffffffffffff | 6th sheet - Name: _Custom2_ | ^ | D3 Ax0d80 C7 | 0x0D87 3463 | uint16 | ^ | 00 00h 0 | ff ffh 65535 | 6th sheet - Z offset | ^ | D3 Ax0d87 C2 | 0x0D89 3465 | uint8 | ^ | 00h 0 | ffh 255 | 6th sheet - bed temp | ^ | D3 Ax0d89 C1 | 0x0D8A 3466 | uint8 | ^ | 00h 0 | ffh 255 | 6th sheet - PINDA temp | ^ | D3 Ax0d8a C1 | 0x0D8B 3467 | char | _7th Sheet block_ | 437573746f6d33| ffffffffffffff | 7th sheet - Name: _Custom3_ | ^ | D3 Ax0d8b C7 | 0x0D92 3474 | uint16 | ^ | 00 00h 0 | ff ffh 65535 | 7th sheet - Z offset | ^ | D3 Ax0d92 C2 | 0x0D94 3476 | uint8 | ^ | 00h 0 | ffh 255 | 7th sheet - bed temp | ^ | D3 Ax0d94 C1 | 0x0D95 3477 | uint8 | ^ | 00h 0 | ffh 255 | 7th sheet - PINDA temp | ^ | D3 Ax0d95 C1 | 0x0D96 3478 | char | _8th Sheet block_ | 437573746f6d34| ffffffffffffff | 8th sheet - Name: _Custom4_ | ^ | D3 Ax0d96 C7 | 0x0D9D 3485 | uint16 | ^ | 00 00h 0 | ff ffh 65535 | 8th sheet - Z offset | ^ | D3 Ax0d9d C2 | 0x0D9F 3487 | uint8 | ^ | 00h 0 | ffh 255 | 8th sheet - bed temp | ^ | D3 Ax0d9f C1 | 0x0DA0 3488 | uint8 | ^ | 00h 0 | ffh 255 | 8th sheet - PINDA temp | ^ | D3 Ax0da0 C1 | 0x0DA1 3489 | uint8 | ??? | 00h 0 | ffh 255 | ??? | ??? | D3 Ax0da1 C1 | 0x0D48 3400 | uint8 | EEPROM_FSENSOR_PCB | ??? | ffh 255 | Filament Sensor type old vs new | ??? | D3 Ax0d48 C1 | ^ | ^ | ^ | ??? | ^ | Filament Sensor type ??? | ^ | ^ | 0x0D47 3399 | uint8 | EEPROM_FSENSOR_ACTION_NA | 00h 0 | ffh 255 | Filament Sensor action: __Continue__ | LCD menu | D3 Ax0d47 C1 | ^ | ^ | ^ | 01h 1 | ^ | Filament Sensor action: __Pause__ | ^ | ^ | 0x0D37 3383 | float | EEPROM_UVLO_SAVED_TARGET | ??? | ff ff ff ffh | Power panic saved target all-axis | ??? | D3 Ax0d37 C16 | ^ | ^ | ^ | ??? | ^ | Power panic saved target e-axis | ^ | D3 Ax0d43 C4 | ^ | ^ | ^ | ??? | ^ | Power panic saved target z-axis | ^ | D3 Ax0d3f C4 | ^ | ^ | ^ | ??? | ^ | Power panic saved target y-axis | ^ | D3 Ax0d3b C4 | ^ | ^ | ^ | ??? | ^ | Power panic saved target x-axis | ^ | D3 Ax0d37 C4 | 0x0D35 3381 | uint16 | EEPROM_UVLO_FEEDMULTIPLY | ??? | ff ffh 65355 | Power panic saved feed multiplier | ??? | D3 Ax0d35 C2 | 0x0D34 3380 | uint8 | EEPROM_BACKLIGHT_LEVEL_HIGH | 00h - ffh | 80h 128 | LCD backlight bright: __128__ Dim value to 255 | LCD menu | D3 Ax0d34 C1 | 0x0D33 3379 | uint8 | EEPROM_BACKLIGHT_LEVEL_LOW | 00h - ffh | 32h 50 | LCD backlight dim: __50__ 0 to Bright value | LCD menu | D3 Ax0d33 C1 | 0x0D32 3378 | uint8 | EEPROM_BACKLIGHT_MODE | 02h 2 | ffh 255 | LCD backlight mode: __Auto__ | LCD menu | D3 Ax0d32 C1 | ^ | ^ | ^ | 01h 1 | ^ | LCD backlight mode: __Bright__ | ^ | ^ | ^ | ^ | ^ | 00h 0 | ^ | LCD backlight mode: __Dim__ | ^ | ^ | 0x0D30 3376 | uint16 | EEPROM_BACKLIGHT_TIMEOUT | 01 00 - ff ff | ff ffh 65535 | LCD backlight timeout: __10__ seconds | LCD menu | D3 Ax0d30 C2 | 0x0D2C 3372 | float | EEPROM_UVLO_LA_K | ??? | ff ff ff ffh | Power panic saved Linear Advanced K value | ??? | D3 Ax0d2c C4 ## End of EEPROM Table | Adress begin | Bit/Type | Name | Valid values | Default/FactoryReset | Description | Gcode/Function| Debug code | :--: | :--: | :--: | :--: | :--: | :--: | :--: | :--: | 0x0012 18 | uint16 | EEPROM_FIRMWARE_VERSION_END | ??? | ff ffh 65535 | ??? | ??? | D3 Ax0012 C2 | 0x0010 16 | uint16 | EEPROM_FIRMWARE_VERSION_FLAVOR | ??? | ff ffh 65535 | ??? | ??? | D3 Ax0010 C2 | 0x000E 14 | uint16 | EEPROM_FIRMWARE_VERSION_REVISION | ??? | ff ffh 65535 | Firmware version revision number DEV/ALPHA/BETA/RC| ??? | D3 Ax000e C2 | 0x000C 12 | uint16 | EEPROM_FIRMWARE_VERSION_MINOR | ??? | ff ffh 65535 | Firmware version minor number | ??? | D3 Ax000c C2 | 0x000A 10 | uint16 | EEPROM_FIRMWARE_VERSION_MAJOR | ??? | ff ffh 65535 | Firmware version major number | ??? | D3 Ax000a C2 */ #define EEPROM_EMPTY_VALUE 0xFF #define EEPROM_EMPTY_VALUE16 0xFFFF // The total size of the EEPROM is // 4096 for the Atmega2560 #define EEPROM_TOP 4096 #define EEPROM_SILENT 4095 #define EEPROM_LANG 4094 #define EEPROM_BABYSTEP_X 4092 //unused #define EEPROM_BABYSTEP_Y 4090 //unused #define EEPROM_BABYSTEP_Z 4088 //legacy, multiple values stored now in EEPROM_Sheets_base #define EEPROM_CALIBRATION_STATUS 4087 #define EEPROM_BABYSTEP_Z0 4085 #define EEPROM_FILAMENTUSED 4081 // uint32_t #define EEPROM_TOTALTIME 4077 #define EEPROM_BED_CALIBRATION_CENTER (EEPROM_TOTALTIME-2*4) #define EEPROM_BED_CALIBRATION_VEC_X (EEPROM_BED_CALIBRATION_CENTER-2*4) #define EEPROM_BED_CALIBRATION_VEC_Y (EEPROM_BED_CALIBRATION_VEC_X-2*4) // Offsets of the Z heiths of the calibration points from the first point. // The offsets are saved as 16bit signed int, scaled to tenths of microns. #define EEPROM_BED_CALIBRATION_Z_JITTER (EEPROM_BED_CALIBRATION_VEC_Y-2*8) #define EEPROM_FARM_MODE (EEPROM_BED_CALIBRATION_Z_JITTER-1) #define EEPROM_FARM_NUMBER (EEPROM_FARM_MODE-3) // Correction of the bed leveling, in micrometers. // Maximum 50 micrometers allowed. // Bed correction is valid if set to 1. If set to zero or 255, the successive 4 bytes are invalid. #define EEPROM_BED_CORRECTION_VALID (EEPROM_FARM_NUMBER-1) #define EEPROM_BED_CORRECTION_LEFT (EEPROM_BED_CORRECTION_VALID-1) #define EEPROM_BED_CORRECTION_RIGHT (EEPROM_BED_CORRECTION_LEFT-1) #define EEPROM_BED_CORRECTION_FRONT (EEPROM_BED_CORRECTION_RIGHT-1) #define EEPROM_BED_CORRECTION_REAR (EEPROM_BED_CORRECTION_FRONT-1) #define EEPROM_TOSHIBA_FLASH_AIR_COMPATIBLITY (EEPROM_BED_CORRECTION_REAR-1) #define EEPROM_PRINT_FLAG (EEPROM_TOSHIBA_FLASH_AIR_COMPATIBLITY-1) #define EEPROM_PROBE_TEMP_SHIFT (EEPROM_PRINT_FLAG - 2*5) //5 x int for storing pinda probe temp shift relative to 50 C; unit: motor steps #define EEPROM_TEMP_CAL_ACTIVE (EEPROM_PROBE_TEMP_SHIFT - 1) #define EEPROM_BOWDEN_LENGTH (EEPROM_TEMP_CAL_ACTIVE - 2*4) //4 x int for bowden lengths for multimaterial #define EEPROM_CALIBRATION_STATUS_PINDA (EEPROM_BOWDEN_LENGTH - 1) //0 - not calibrated; 1 - calibrated #define EEPROM_UVLO (EEPROM_CALIBRATION_STATUS_PINDA - 1) //1 - uvlo during print #define EEPROM_UVLO_CURRENT_POSITION (EEPROM_UVLO-2*4) // 2 x float for current_position in X and Y axes #define EEPROM_FILENAME (EEPROM_UVLO_CURRENT_POSITION - 8) //8chars to store filename without extension #define EEPROM_FILE_POSITION (EEPROM_FILENAME - 4) //32 bit for uint32_t file position #define EEPROM_UVLO_CURRENT_POSITION_Z (EEPROM_FILE_POSITION - 4) //float for current position in Z #define EEPROM_UVLO_UNUSED_001 (EEPROM_UVLO_CURRENT_POSITION_Z - 1) // uint8_t (unused) #define EEPROM_UVLO_TARGET_BED (EEPROM_UVLO_UNUSED_001 - 1) #define EEPROM_UVLO_FEEDRATE (EEPROM_UVLO_TARGET_BED - 2) //uint16_t #define EEPROM_UVLO_FAN_SPEED (EEPROM_UVLO_FEEDRATE - 1) #define EEPROM_FAN_CHECK_ENABLED (EEPROM_UVLO_FAN_SPEED - 1) #define EEPROM_UVLO_MESH_BED_LEVELING (EEPROM_FAN_CHECK_ENABLED - 9*2) #define EEPROM_UVLO_Z_MICROSTEPS (EEPROM_UVLO_MESH_BED_LEVELING - 2) // uint16_t (could be removed) #define EEPROM_UVLO_E_ABS (EEPROM_UVLO_Z_MICROSTEPS - 1) #define EEPROM_UVLO_CURRENT_POSITION_E (EEPROM_UVLO_E_ABS - 4) //float for current position in E // Crash detection mode EEPROM setting #define EEPROM_CRASH_DET (EEPROM_UVLO_CURRENT_POSITION_E - 5) // float (orig EEPROM_UVLO_MESH_BED_LEVELING-12) // Crash detection counter Y (last print) #define EEPROM_CRASH_COUNT_Y (EEPROM_CRASH_DET - 1) // uint8 (orig EEPROM_UVLO_MESH_BED_LEVELING-15) // Filament sensor on/off EEPROM setting #define EEPROM_FSENSOR (EEPROM_CRASH_COUNT_Y - 1) // uint8 (orig EEPROM_UVLO_MESH_BED_LEVELING-14) // Crash detection counter X (last print) #define EEPROM_CRASH_COUNT_X (EEPROM_FSENSOR - 1) // uint8 (orig EEPROM_UVLO_MESH_BED_LEVELING-15) // Filament runout/error coutner (last print) #define EEPROM_FERROR_COUNT (EEPROM_CRASH_COUNT_X - 1) // uint8 (orig EEPROM_UVLO_MESH_BED_LEVELING-16) // Power loss errors (last print) #define EEPROM_POWER_COUNT (EEPROM_FERROR_COUNT - 1) // uint8 (orig EEPROM_UVLO_MESH_BED_LEVELING-17) #define EEPROM_XYZ_CAL_SKEW (EEPROM_POWER_COUNT - 4) // float for skew backup #define EEPROM_WIZARD_ACTIVE (EEPROM_XYZ_CAL_SKEW - 1) #define EEPROM_BELTSTATUS_X (EEPROM_WIZARD_ACTIVE - 2) // uint16 #define EEPROM_BELTSTATUS_Y (EEPROM_BELTSTATUS_X - 2) // uint16 #define EEPROM_DIR_DEPTH (EEPROM_BELTSTATUS_Y-1) #define EEPROM_DIRS (EEPROM_DIR_DEPTH-80) //8 chars for each dir name, max 10 levels #define EEPROM_SD_SORT (EEPROM_DIRS - 1) //0 -time, 1-alpha, 2-none #define EEPROM_SECOND_SERIAL_ACTIVE (EEPROM_SD_SORT - 1) #define EEPROM_FSENS_AUTOLOAD_ENABLED (EEPROM_SECOND_SERIAL_ACTIVE - 1) // Crash detection counter X (total) #define EEPROM_CRASH_COUNT_X_TOT (EEPROM_FSENS_AUTOLOAD_ENABLED - 2) // uint16 // Crash detection counter Y (total) #define EEPROM_CRASH_COUNT_Y_TOT (EEPROM_CRASH_COUNT_X_TOT - 2) // uint16 // Filament runout/error coutner (total) #define EEPROM_FERROR_COUNT_TOT (EEPROM_CRASH_COUNT_Y_TOT - 2) // uint16 // Power loss errors (total) #define EEPROM_POWER_COUNT_TOT (EEPROM_FERROR_COUNT_TOT - 2) // uint16 //////////////////////////////////////// // TMC2130 Accurate sensorless homing // X-axis home origin (stepper phase in microsteps, 0..63 for 16ustep resolution) #define EEPROM_TMC2130_HOME_X_ORIGIN (EEPROM_POWER_COUNT_TOT - 1) // uint8 // X-axis home bsteps (number of microsteps backward) #define EEPROM_TMC2130_HOME_X_BSTEPS (EEPROM_TMC2130_HOME_X_ORIGIN - 1) // uint8 // X-axis home fsteps (number of microsteps forward) #define EEPROM_TMC2130_HOME_X_FSTEPS (EEPROM_TMC2130_HOME_X_BSTEPS - 1) // uint8 // Y-axis home origin (stepper phase in microsteps, 0..63 for 16ustep resolution) #define EEPROM_TMC2130_HOME_Y_ORIGIN (EEPROM_TMC2130_HOME_X_FSTEPS - 1) // uint8 // X-axis home bsteps (number of microsteps backward) #define EEPROM_TMC2130_HOME_Y_BSTEPS (EEPROM_TMC2130_HOME_Y_ORIGIN - 1) // uint8 // X-axis home fsteps (number of microsteps forward) #define EEPROM_TMC2130_HOME_Y_FSTEPS (EEPROM_TMC2130_HOME_Y_BSTEPS - 1) // uint8 // Accurate homing enabled #define EEPROM_TMC2130_HOME_ENABLED (EEPROM_TMC2130_HOME_Y_FSTEPS - 1) // uint8 //////////////////////////////////////// // TMC2130 uStep linearity correction // Linearity correction factor (XYZE) #define EEPROM_TMC2130_WAVE_X_FAC (EEPROM_TMC2130_HOME_ENABLED - 1) // uint8 #define EEPROM_TMC2130_WAVE_Y_FAC (EEPROM_TMC2130_WAVE_X_FAC - 1) // uint8 #define EEPROM_TMC2130_WAVE_Z_FAC (EEPROM_TMC2130_WAVE_Y_FAC - 1) // uint8 #define EEPROM_TMC2130_WAVE_E_FAC (EEPROM_TMC2130_WAVE_Z_FAC - 1) // uint8 //////////////////////////////////////// // TMC2130 uStep resolution // microstep resolution (XYZE): usteps = (256 >> mres) #define EEPROM_TMC2130_X_MRES (EEPROM_TMC2130_WAVE_E_FAC - 1) // uint8 #define EEPROM_TMC2130_Y_MRES (EEPROM_TMC2130_X_MRES - 1) // uint8 #define EEPROM_TMC2130_Z_MRES (EEPROM_TMC2130_Y_MRES - 1) // uint8 #define EEPROM_TMC2130_E_MRES (EEPROM_TMC2130_Z_MRES - 1) // uint8 // HW #define EEPROM_PRINTER_TYPE (EEPROM_TMC2130_E_MRES - 2) // uint16 #define EEPROM_BOARD_TYPE (EEPROM_PRINTER_TYPE - 2) // uint16 // Extruder multiplier for power panic #define EEPROM_EXTRUDER_MULTIPLIER_0 (EEPROM_BOARD_TYPE - 4) //float #define EEPROM_EXTRUDER_MULTIPLIER_1 (EEPROM_EXTRUDER_MULTIPLIER_0 - 4) //float #define EEPROM_EXTRUDER_MULTIPLIER_2 (EEPROM_EXTRUDER_MULTIPLIER_1 - 4) //float #define EEPROM_EXTRUDEMULTIPLY (EEPROM_EXTRUDER_MULTIPLIER_2 - 2) // uint16 #define EEPROM_UVLO_TINY_CURRENT_POSITION_Z (EEPROM_EXTRUDEMULTIPLY-4) // float #define EEPROM_UVLO_TARGET_HOTEND (EEPROM_UVLO_TINY_CURRENT_POSITION_Z-2) // uint16 // Sound Mode #define EEPROM_SOUND_MODE (EEPROM_UVLO_TARGET_HOTEND-1) // uint8 #define EEPROM_AUTO_DEPLETE (EEPROM_SOUND_MODE-1) //bool #define EEPROM_FSENS_OQ_MEASS_ENABLED (EEPROM_AUTO_DEPLETE - 1) //bool #define EEPROM_MMU_FAIL_TOT (EEPROM_FSENS_OQ_MEASS_ENABLED - 2) //uint16_t #define EEPROM_MMU_FAIL (EEPROM_MMU_FAIL_TOT - 1) //uint8_t #define EEPROM_MMU_LOAD_FAIL_TOT (EEPROM_MMU_FAIL - 2) //uint16_t #define EEPROM_MMU_LOAD_FAIL (EEPROM_MMU_LOAD_FAIL_TOT - 1) //uint8_t #define EEPROM_MMU_CUTTER_ENABLED (EEPROM_MMU_LOAD_FAIL - 1) #define EEPROM_UVLO_MESH_BED_LEVELING_FULL (EEPROM_MMU_CUTTER_ENABLED - 12*12*2) //allow 12 calibration points for future expansion #define EEPROM_MBL_TYPE (EEPROM_UVLO_MESH_BED_LEVELING_FULL-1) //uint8_t for mesh bed leveling precision #define EEPROM_MBL_MAGNET_ELIMINATION (EEPROM_MBL_TYPE -1) #define EEPROM_MBL_POINTS_NR (EEPROM_MBL_MAGNET_ELIMINATION -1) //uint8_t number of points in one exis for mesh bed leveling #define EEPROM_MBL_PROBE_NR (EEPROM_MBL_POINTS_NR-1) //number of measurements for each point #define EEPROM_MMU_STEALTH (EEPROM_MBL_PROBE_NR-1) #define EEPROM_CHECK_MODE (EEPROM_MMU_STEALTH-1) // uint8 #define EEPROM_NOZZLE_DIAMETER (EEPROM_CHECK_MODE-1) // uint8 #define EEPROM_NOZZLE_DIAMETER_uM (EEPROM_NOZZLE_DIAMETER-2) // uint16 #define EEPROM_CHECK_MODEL (EEPROM_NOZZLE_DIAMETER_uM-1) // uint8 #define EEPROM_CHECK_VERSION (EEPROM_CHECK_MODEL-1) // uint8 #define EEPROM_CHECK_GCODE (EEPROM_CHECK_VERSION-1) // uint8 #define EEPROM_SHEETS_BASE (EEPROM_CHECK_GCODE - EEPROM_SHEETS_SIZEOF) // Sheets static Sheets * const EEPROM_Sheets_base = (Sheets*)(EEPROM_SHEETS_BASE); #define EEPROM_FSENSOR_PCB (EEPROM_SHEETS_BASE-1) // uint8 #define EEPROM_FSENSOR_ACTION_NA (EEPROM_FSENSOR_PCB-1) // uint8 #define EEPROM_UVLO_SAVED_TARGET (EEPROM_FSENSOR_ACTION_NA - 4*4) // 4 x float for saved target for all axes #define EEPROM_UVLO_FEEDMULTIPLY (EEPROM_UVLO_SAVED_TARGET - 2) // uint16_t for feedmultiply #define EEPROM_BACKLIGHT_LEVEL_HIGH (EEPROM_UVLO_FEEDMULTIPLY-1) // uint8 #define EEPROM_BACKLIGHT_LEVEL_LOW (EEPROM_BACKLIGHT_LEVEL_HIGH-1) // uint8 #define EEPROM_BACKLIGHT_MODE (EEPROM_BACKLIGHT_LEVEL_LOW-1) // uint8 #define EEPROM_BACKLIGHT_TIMEOUT (EEPROM_BACKLIGHT_MODE-2) // uint16 #define EEPROM_UVLO_LA_K (EEPROM_BACKLIGHT_TIMEOUT-4) // float //This is supposed to point to last item to allow EEPROM overrun check. Please update when adding new items. #define EEPROM_LAST_ITEM EEPROM_UVLO_LA_K // !!!!! // !!!!! this is end of EEPROM section ... all updates MUST BE inserted before this mark !!!!! // !!!!! // Currently running firmware, each digit stored as uint16_t. // The flavor differentiates a dev, alpha, beta, release candidate or a release version. #define EEPROM_FIRMWARE_VERSION_END (FW_PRUSA3D_MAGIC_LEN+8) #define EEPROM_FIRMWARE_VERSION_FLAVOR (FW_PRUSA3D_MAGIC_LEN+6) #define EEPROM_FIRMWARE_VERSION_REVISION (FW_PRUSA3D_MAGIC_LEN+4) #define EEPROM_FIRMWARE_VERSION_MINOR (FW_PRUSA3D_MAGIC_LEN+2) #define EEPROM_FIRMWARE_VERSION_MAJOR FW_PRUSA3D_MAGIC_LEN // Magic string, indicating that the current or the previous firmware running was the Prusa3D firmware. #define EEPROM_FIRMWARE_PRUSA_MAGIC 0 #ifdef __cplusplus #include "ConfigurationStore.h" static_assert(EEPROM_FIRMWARE_VERSION_END < 20, "Firmware version EEPROM address conflicts with EEPROM_M500_base"); static constexpr M500_conf * const EEPROM_M500_base = reinterpret_cast(20); //offset for storing settings using M500 static_assert(((sizeof(M500_conf) + 20) < EEPROM_LAST_ITEM), "M500_conf address space conflicts with previous items."); #endif enum { EEPROM_MMU_CUTTER_ENABLED_enabled = 1, EEPROM_MMU_CUTTER_ENABLED_always = 2, }; #ifdef __cplusplus void eeprom_init(); bool eeprom_is_sheet_initialized(uint8_t sheet_num); struct SheetName { char c[sizeof(Sheet::name) + 1]; }; void eeprom_default_sheet_name(uint8_t index, SheetName &sheetName); int8_t eeprom_next_initialized_sheet(int8_t sheet); void eeprom_switch_to_next_sheet(); #endif #endif // EEPROM_H