3DPrinting/Prusa-Firmware
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
2591f8d593
Prusa-Firmware/Firmware/eeprom.h
3d-gussner 2591f8d593 Added and tested more... 
... have to take a short break
2020-03-20 12:36:26 +01:00

403 lines
26 KiB
C
Raw Blame History

/**
* @file
*/
/** \ingroup eeprom_table */
//! _This is a EEPROM table of currently implemented in Prusa firmware (dynamically generated from doxygen)._
#ifndef EEPROM_H
#define EEPROM_H
#include <stdint.h>
#define MAX_SHEETS 8
#define MAX_SHEET_NAME_LENGTH 7
typedef struct
{
char name[MAX_SHEET_NAME_LENGTH]; //!< Can be null terminated, doesn't need to be null terminated
int16_t z_offset; //!< Z_BABYSTEP_MIN .. Z_BABYSTEP_MAX = Z_BABYSTEP_MIN*2/1000 [mm] .. Z_BABYSTEP_MAX*2/1000 [mm]
uint8_t bed_temp; //!< 0 .. 254 [°C]
uint8_t pinda_temp; //!< 0 .. 254 [°C]
} Sheet;
typedef struct
{
Sheet s[MAX_SHEETS];
uint8_t active_sheet;
} Sheets;
// sizeof(Sheets). Do not change it unless EEPROM_Sheets_base is last item in EEPROM.
// Otherwise it would move following items.
#define EEPROM_SHEETS_SIZEOF 89
#ifdef __cplusplus
static_assert(sizeof(Sheets) == EEPROM_SHEETS_SIZEOF, "Sizeof(Sheets) is not EEPROM_SHEETS_SIZEOF.");
#endif
/** @defgroup eeprom_table EEPROM Table
*
---------------------------------------------------------------------------------
EEPROM 8-bit Empty value = 0xFFh 255
EEPROM 16-bit Empty value = 0xFFFFh 65535
---------------------------------------------------------------------------------
How can you use the debug codes?
- Serial terminal like Putty.
- Octoprint does support D-codes
- _Pronterface_ does <b>not</b> support D-codes
---------------------------------------------------------------------------------
## EEPROM Tabel
| Adress begin | Bit/Type | Name | Valid values | Default/FactoryReset | Description | Gcode/Function| Debug code
| :--: | :--: | :--: | :--: | :--: | :--: | :--: | :--:
| 0x0FFFh 4095 | uchar | EEPROM_SILENT | 00h 0 | ffh 255 | TMC Stealth mode off / miniRambo Power mode | LCD menu | D3 Ax0fff C1
| ^ | ^ | ^ | 01h 1 | ^ | TMC Stealth mode on / miniRambo Silent mode | ^ | ^
| 0x0FFEh 4094 | uchar | EEPROM_LANG | 00h 0 | ffh 255 | English / LANG_ID_PRI | LCD menu | D3 Ax0ffe C1
| ^ | ^ | ^ | 01h 1 | ^ | Other language LANG_ID_SEC | ^ | ^
| 0x0FFCh 4092 | uint16 | EEPROM_BABYSTEP_X | ??? | ffh 255 | Babystep for X axis _unsued_ | ??? | D3 Ax0ffc C2
| 0x0FFAh 4090 | uint16 | EEPROM_BABYSTEP_Y | ??? | ffh 255 | Babystep for Y axis _unsued_ | ^ | D3 Ax0ffa C2
| 0x0FF8h 4088 | uint16 | EEPROM_BABYSTEP_Z | ??? | ffh 255 | Babystep for Z axis _lagacy_ | ^ | D3 Ax0ff8 C2
| ^ | ^ | ^ | ^ | ^ | multiple values stored now in EEPROM_Sheets_base | ^ | ^
| 0x0FF7h 4087 | uint8 | EEPROM_CALIBRATION_STATUS | 00h 0 | ffh 255 | Unknown | ??? | D3 Ax0ff7 C1
| ^ | ^ | ^ | 01h 1 | ^ | Calibrated | ^ | ^
| ^ | ^ | ^ | E6h 230 | ^ | needs Live Z adjustment | ^ | ^
| ^ | ^ | ^ | F0h 240 | ^ | needs Z calibration | ^ | ^
| ^ | ^ | ^ | FAh 250 | ^ | needs XYZ calibration | ^ | ^
| ^ | ^ | ^ | FFh 255 | ^ | Assbemled _default_ | ^ | ^
| 0x0FF5h 4085 | uint16 | EEPROM_BABYSTEP_Z0 | ??? | ??? | Babystep for Z ??? | ??? | D3 Ax0ff5 C2
| 0x0FF1h 4081 | uint32 | EEPROM_FILAMENTUSED | ??? | 00h 0 | Filament used in meters | ??? | D3 Ax0ff1 C4
| 0x0FEDh 4077 | uint32 | EEPROM_TOTALTIME | ??? | 00h 0 | Total print time | ??? | D3 Ax0fed C4
| 0x0FE5h 4069 | float | EEPROM_BED_CALIBRATION_CENTER | ??? | ??? | ??? | ??? | D3 Ax0fe5 C8
| ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^
| 0x0FDDh 4061 | float | EEPROM_BED_CALIBRATION_VEC_X | ??? | ??? | ??? | ??? | D3 Ax0fdd C8
| ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^
| 0x0FD5h 4053 | float | EEPROM_BED_CALIBRATION_VEC_Y | ??? | ??? | ??? | ??? | D3 Ax0fd5 C8
| ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^
| 0x0FC5h 4037 | int16 | EEPROM_BED_CALIBRATION_Z_JITTER | ??? | ??? | ??? | ??? | D3 Ax0fc5 C16
| ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^
| ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^
| ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^
| ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^
| ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^
| ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^
| ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^
| 0x0FC4h 4036 | bool | EEPROM_FARM_MODE | 00h 0 | ffh 255 | Prusa farm mode off | G99 | D3 Ax0fc4 C1
| ^ | ^ | ^ | 01h 1 | ^ | Prusa farm mode on | G98 | ^
| 0x0FC1h 4033 | int16 | EEPROM_FARM_NUMBER | ??? | ff ff ffh | Prusa farm number | ??? | D3 Ax0fc1 C3
| 0x0FC0h 4032 | bool | EEPROM_BED_CORRECTION_VALID | 00h 0 | 00h 0 | Bed correction invalid | ??? | D3 Ax0fc0 C1
| ^ | ^ | ^ | ffh 255 | | Bed correction valid ^ | ??? | ^
| 0x0FBFh 4031 | char | EEPROM_BED_CORRECTION_LEFT | 00h FFh | 00h 0 | Bed manual correction left | LCD menu | D3 Ax0fbf C1
| ^ | ^ | ^ | ??? | ??? | At this moment limited to +-100um | ^ | ^
| 0x0FBEh 4030 | char | EEPROM_BED_CORRECTION_RIGHT | 00h FFh | 00h 0 | Bed manual correction right | LCD menu | D3 Ax0fbe C1
| ^ | ^ | ^ | ??? | ??? | At this moment limited to +-100um | ^ | ^
| 0x0FBDh 4029 | char | EEPROM_BED_CORRECTION_FRONT | 00h FFh | 00h 0 | Bed manual correction front | LCD menu | D3 Ax0fbd C1
| ^ | ^ | ^ | ??? | ??? | At this moment limited to +-100um | ^ | ^
| 0x0FBCh 4028 | char | EEPROM_BED_CORRECTION_BACK | 00h FFh | 00h 0 | Bed manual correction back | LCD menu | D3 Ax0fbc C1
| ^ | ^ | ^ | ??? | ??? | At this moment limited to +-100um | ^ | ^
| 0x0FBBh 4027 | bool | EEPROM_TOSHIBA_FLASH_AIR_COMPATIBLITY | 00h 0 | 00h 0 | Toshiba Air off | LCD menu | D3 Ax0fbb C1
| ^ | ^ | ^ | ??? | ffh 255 | Toshiba Air oon | ^ | ^
| 0x0FBAh 4026 | uchar | EEPROM_PRINT_FLAG | ??? | ??? | _unsued_ | ??? | D3 Ax0fba C1
| 0x0FB0h 4016 | int16 | EEPROM_PROBE_TEMP_SHIFT | ??? | ??? | ??? | ??? | D3 Ax0fb0 C10
| ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^
| ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^
| ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^
| ^ | ^ | ^ | ??? | ??? | ??? | ^ | ^
| 0x0FAFh 4015 | bool | EEPROM_TEMP_CAL_ACTIVE | 00h 0 | 00h 0 | PINDA Temp cal. inactive | LCD menu | D3 Ax0faf C1
| ^ | ^ | ^ | ffh 255 | ^ | PINDA Temp cal. active | ^ | ^
| 0x0FA7h 4007 | uint32 | EEPROM_BOWDEN_LENGTH | ??? | ff 00 ff ffh | Bowden length | ??? | D3 Ax0fae C8
| ^ | ^ | ^ | ??? | ff ff ff ffh | ^ | ^ | ^
| 0x0FA6h 4006 | uint8 | EEPROM_CALIBRATION_STATUS_PINDA | 00h 0 | ffh 255 | PINDA Temp not calibrated | ??? | D3 Ax0fa6 C1
| ^ | ^ | ^ | 01h 1 | ^ | PINDA Temp calibrated | ^ | ^
| 0x0FA5h 4005 | uint8 | EEPROM_UVLO | 00h 0 | ffh 255 | Power Panic flag inactive | ??? | D3 Ax0fa5 C1
| ^ | ^ | ^ | 01h 1 | ^ | Power Panic flag active | ^ | ^
| ^ | ^ | ^ | 02h 2 | ^ | Power Panic flag ??? | ^ | ^
| 0x0F9Dh 3997 | float | EEPROM_UVLO_CURRENT_POSITION | ??? | ffh 255 | Power Panic position | ??? | D3 Ax0f9d C8
| ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^
| 0x0F95h 3989 | char | EEPROM_FILENAME | ??? | ffh 255 | Power Panic Filename | ??? | D3 Ax0f95 C8
| ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^
| ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^
| ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^
| ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^
| ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^
| ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^
| ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^
| 0x0F91h 39851 | uint32 | EEPROM_FILE_POSITION | ??? | ff ff ff ffh | Power Panic File Postion | ??? | D3 Ax0f91 C4
| 0x0F8Dh 3981 | float | EEPROM_UVLO_CURRENT_POSITION_Z | ??? | ff ff ff ffh | Power Panic Z Position | ^ | D3 Ax0f8d C4
| 0x0F8Ch 3980 | ??? | EEPROM_UVLO_UNUSED_001 | ??? | ffh 255 | Power Panic UNUSED | ^ | D3 Ax0f8c C1
| 0x0F8Bh 3979 | uint8 | EEPROM_UVLO_TARGET_BED | ??? | ffh 255 | Power Panic Bed temperature | ^ | D3 Ax0f8b C1
| 0x0F89h 3977 | uint16 | EEPROM_UVLO_FEEDRATE | ??? | ff ffh 65535 | Power Panic Feedrate | ^ | D3 Ax0f89 C2
| 0x0F88h 3976 | uint8 | EEPROM_UVLO_FAN_SPEED | ??? | ffh 255 | Power Panic Fan speed | ^ | D3 Ax0f88 C1
| 0x0F87h 3975 | uint8 | EEPROM_FAN_CHECK_ENABLED | 00h 0 | ??? | Fan Check disabled | LCD menu | D3 Ax0f87 C1
| ^ | ^ | ^ | 01h 1 | ffh 255 | Fan Check enabled (exception ffh=01h) | ^ | ^
| 0x0F75h 3957 | uint16 | EEPROM_UVLO_MESH_BED_LEVELING | ??? | ff ffh 65535 | Power Panic Mesh Bed Leveling | ??? | D3 Ax0f75 C18
| ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^
| ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^
| ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^
| ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^
| ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^
| ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^
| ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^
| ^ | ^ | ^ | ??? | ^ | ^ | ^ | ^
| 0x0F73h 3955 | uint16 | EEPROM_UVLO_Z_MICROSTEPS | ??? | ff ffh 65535 | Power Panic Z microsteps | ??? | D3 Ax0f73 C2
| 0x0F72h 3954 | uint8 | EEPROM_UVLO_E_ABS | ??? | ffh 255 | Power Panic ??? position | ??? | D3 Ax0f72 C1
| 0x0F6Eh 3950 | foat | EEPROM_UVLO_CURRENT_POSITION_E | ??? | ff ff ff ffh | Power Panic E position | ??? | D3 Ax0f6e C4
| 0x0F69h 3945 | uint8 | EEPROM_CRASH_DET | ffh 255 | ffh 255 | Crash detection enabled | LCD menu | D3 Ax0f69 C5
| ^ | ^ | ^ | 00h 0 | ^ | Crash detection disabled | LCD menu | ^
| ^ | ^ | ^ | ??? | ??? | ^ | ??? | ^
| ^ | ^ | ^ | ??? | ??? | ^ | ??? | ^
| ^ | ^ | ^ | ??? | ??? | ^ | ??? | ^
| 0x0F68h 3944 | uint8 | EEPROM_CRASH_COUNT_Y | 00h-ffh 0-255 | ffh 255 | Crashes detected on y axis | ??? | D3 Ax0f68 C1
| 0x0F67h 3943 | uint8 | EEPROM_FSENSOR | 01h 1 | ffh 255 | Filament sensor enabled | LCD menu | D3 Ax0f67 C1
| 0x0F65h 3942 | uint8 | EEPROM_CRASH_COUNT_X | 00h-ffh 0-255 | ffh 255 | Crashes detected on x axis | ??? | D3 Ax0f66 C1
| 0x0F65h 3941 | uint8 | EEPROM_FERROR_COUNT | 00h-ffh 0-255 | ffh 255 | Filament sensor error counter | ??? | D3 Ax0f65 C1
| 0x0F64h 3940 | uint8 | EEPROM_POWER_COUNT | 00h-ffh 0-255 | ffh 255 | Power failure counter | ??? | D3 Ax0f64 C1
| 0x0F60h 3936 | float | EEPROM_XYZ_CAL_SKEW | ??? | ff ff ff ffh | XYZ skew value | ??? | D3 Ax0f60 C4
| 0x0F5Fh 3935 | uint8 | EEPROM_WIZARD_ACTIVE | 00h 0 | ??? | Wizard active | ??? | D3 Ax0f5f C1
| ^ | ^ | ^ | 01h 1 | ??? | ^ | ^ | ^
| 0x0F5Dh 3933 | uint16 | EEPROM_BELTSTATUS_X | ??? | ff ffh | X Beltstatus | ??? | D3 Ax0f5d C2
| 0x0F5Bh 3931 | uint16 | EEPROM_BELTSTATUS_Y | ??? | ff ffh | Y Beltstatus | ??? | D3 Ax0f5b C2
| 0x0F5Ah 3930 | uint8 | EEPROM_DIR_DEPTH | 00h-ffh 0-255 | ffh 255 | Directory depth | ??? | D3 Ax0f5a C1
| 0x0F0Ah 3850 | uint8 | EEPROM_DIRS | ??? | ffh 255 | Directories ??? | ??? | D3 Ax0f0a C80
| 0x0F09h 3849 | uint8 | EEPROM_SD_SORT | 00h 0 | ffh 255 | SD card sort by time | LCD menu | D3 Ax0f09 C1
| ^ | ^ | ^ | 01h 1 | ^ | SD card sort by alphabet | LCD menu | ^
| ^ | ^ | ^ | 02h 1 | ^ | SD card not sorted | LCD menu | ^
| 0x0F08h 3848 | uint8 | EEPROM_SECOND_SERIAL_ACTIVE | 00h 0 | ffh 255 | RPi Port disabled | LCD menu | D3 Ax0f08 C1
| ^ | ^ | ^ | 01h 1 | ^ | RPi Port enabled | LCD menu | ^
| 0x0F07h 3847 | uint8 | EEPROM_FSENS_AUTOLOAD_ENABLED | 01h 1 | ffh 255 | Filament autoload enabled | LCD menu | D3 Ax0f07 C1
| ^ | ^ | ^ | 00h 0 | ^ | Filament autoload disabled | LCD menu | ^
*/
#define EEPROM_EMPTY_VALUE 0xFF
#define EEPROM_EMPTY_VALUE16 0xFFFF
// The total size of the EEPROM is
// 4096 for the Atmega2560
#define EEPROM_TOP 4096
#define EEPROM_SILENT 4095
#define EEPROM_LANG 4094
#define EEPROM_BABYSTEP_X 4092 //unused
#define EEPROM_BABYSTEP_Y 4090 //unused
#define EEPROM_BABYSTEP_Z 4088 //legacy, multiple values stored now in EEPROM_Sheets_base
#define EEPROM_CALIBRATION_STATUS 4087
#define EEPROM_BABYSTEP_Z0 4085
#define EEPROM_FILAMENTUSED 4081
// uint32_t
#define EEPROM_TOTALTIME 4077
#define EEPROM_BED_CALIBRATION_CENTER (EEPROM_TOTALTIME-2*4)
#define EEPROM_BED_CALIBRATION_VEC_X (EEPROM_BED_CALIBRATION_CENTER-2*4)
#define EEPROM_BED_CALIBRATION_VEC_Y (EEPROM_BED_CALIBRATION_VEC_X-2*4)
// Offsets of the Z heiths of the calibration points from the first point.
// The offsets are saved as 16bit signed int, scaled to tenths of microns.
#define EEPROM_BED_CALIBRATION_Z_JITTER (EEPROM_BED_CALIBRATION_VEC_Y-2*8)
#define EEPROM_FARM_MODE (EEPROM_BED_CALIBRATION_Z_JITTER-1)
#define EEPROM_FARM_NUMBER (EEPROM_FARM_MODE-3)
// Correction of the bed leveling, in micrometers.
// Maximum 50 micrometers allowed.
// Bed correction is valid if set to 1. If set to zero or 255, the successive 4 bytes are invalid.
#define EEPROM_BED_CORRECTION_VALID (EEPROM_FARM_NUMBER-1)
#define EEPROM_BED_CORRECTION_LEFT (EEPROM_BED_CORRECTION_VALID-1)
#define EEPROM_BED_CORRECTION_RIGHT (EEPROM_BED_CORRECTION_LEFT-1)
#define EEPROM_BED_CORRECTION_FRONT (EEPROM_BED_CORRECTION_RIGHT-1)
#define EEPROM_BED_CORRECTION_REAR (EEPROM_BED_CORRECTION_FRONT-1)
#define EEPROM_TOSHIBA_FLASH_AIR_COMPATIBLITY (EEPROM_BED_CORRECTION_REAR-1)
#define EEPROM_PRINT_FLAG (EEPROM_TOSHIBA_FLASH_AIR_COMPATIBLITY-1)
#define EEPROM_PROBE_TEMP_SHIFT (EEPROM_PRINT_FLAG - 2*5) //5 x int for storing pinda probe temp shift relative to 50 C; unit: motor steps
#define EEPROM_TEMP_CAL_ACTIVE (EEPROM_PROBE_TEMP_SHIFT - 1)
#define EEPROM_BOWDEN_LENGTH (EEPROM_TEMP_CAL_ACTIVE - 2*4) //4 x int for bowden lengths for multimaterial
#define EEPROM_CALIBRATION_STATUS_PINDA (EEPROM_BOWDEN_LENGTH - 1) //0 - not calibrated; 1 - calibrated
#define EEPROM_UVLO (EEPROM_CALIBRATION_STATUS_PINDA - 1) //1 - uvlo during print
#define EEPROM_UVLO_CURRENT_POSITION (EEPROM_UVLO-2*4) // 2 x float for current_position in X and Y axes
#define EEPROM_FILENAME (EEPROM_UVLO_CURRENT_POSITION - 8) //8chars to store filename without extension
#define EEPROM_FILE_POSITION (EEPROM_FILENAME - 4) //32 bit for uint32_t file position
#define EEPROM_UVLO_CURRENT_POSITION_Z (EEPROM_FILE_POSITION - 4) //float for current position in Z
#define EEPROM_UVLO_UNUSED_001 (EEPROM_UVLO_CURRENT_POSITION_Z - 1) // uint8_t (unused)
#define EEPROM_UVLO_TARGET_BED (EEPROM_UVLO_UNUSED_001 - 1)
#define EEPROM_UVLO_FEEDRATE (EEPROM_UVLO_TARGET_BED - 2) //uint16_t
#define EEPROM_UVLO_FAN_SPEED (EEPROM_UVLO_FEEDRATE - 1)
#define EEPROM_FAN_CHECK_ENABLED (EEPROM_UVLO_FAN_SPEED - 1)
#define EEPROM_UVLO_MESH_BED_LEVELING (EEPROM_FAN_CHECK_ENABLED - 9*2)
#define EEPROM_UVLO_Z_MICROSTEPS (EEPROM_UVLO_MESH_BED_LEVELING - 2) // uint16_t (could be removed)
#define EEPROM_UVLO_E_ABS (EEPROM_UVLO_Z_MICROSTEPS - 1)
#define EEPROM_UVLO_CURRENT_POSITION_E (EEPROM_UVLO_E_ABS - 4) //float for current position in E
// Crash detection mode EEPROM setting
#define EEPROM_CRASH_DET (EEPROM_UVLO_CURRENT_POSITION_E - 5) // float (orig EEPROM_UVLO_MESH_BED_LEVELING-12)
// Crash detection counter Y (last print)
#define EEPROM_CRASH_COUNT_Y (EEPROM_CRASH_DET - 1) // uint8 (orig EEPROM_UVLO_MESH_BED_LEVELING-15)
// Filament sensor on/off EEPROM setting
#define EEPROM_FSENSOR (EEPROM_CRASH_COUNT_Y - 1) // uint8 (orig EEPROM_UVLO_MESH_BED_LEVELING-14)
// Crash detection counter X (last print)
#define EEPROM_CRASH_COUNT_X (EEPROM_FSENSOR - 1) // uint8 (orig EEPROM_UVLO_MESH_BED_LEVELING-15)
// Filament runout/error coutner (last print)
#define EEPROM_FERROR_COUNT (EEPROM_CRASH_COUNT_X - 1) // uint8 (orig EEPROM_UVLO_MESH_BED_LEVELING-16)
// Power loss errors (last print)
#define EEPROM_POWER_COUNT (EEPROM_FERROR_COUNT - 1) // uint8 (orig EEPROM_UVLO_MESH_BED_LEVELING-17)
#define EEPROM_XYZ_CAL_SKEW (EEPROM_POWER_COUNT - 4) // float for skew backup
#define EEPROM_WIZARD_ACTIVE (EEPROM_XYZ_CAL_SKEW - 1)
#define EEPROM_BELTSTATUS_X (EEPROM_WIZARD_ACTIVE - 2) // uint16
#define EEPROM_BELTSTATUS_Y (EEPROM_BELTSTATUS_X - 2) // uint16
#define EEPROM_DIR_DEPTH (EEPROM_BELTSTATUS_Y-1)
#define EEPROM_DIRS (EEPROM_DIR_DEPTH-80) //8 chars for each dir name, max 10 levels
#define EEPROM_SD_SORT (EEPROM_DIRS - 1) //0 -time, 1-alpha, 2-none
#define EEPROM_SECOND_SERIAL_ACTIVE (EEPROM_SD_SORT - 1)
#define EEPROM_FSENS_AUTOLOAD_ENABLED (EEPROM_SECOND_SERIAL_ACTIVE - 1)
// Crash detection counter X (total)
#define EEPROM_CRASH_COUNT_X_TOT (EEPROM_FSENS_AUTOLOAD_ENABLED - 2) // uint16
// Crash detection counter Y (total)
#define EEPROM_CRASH_COUNT_Y_TOT (EEPROM_CRASH_COUNT_X_TOT - 2) // uint16
// Filament runout/error coutner (total)
#define EEPROM_FERROR_COUNT_TOT (EEPROM_CRASH_COUNT_Y_TOT - 2) // uint16
// Power loss errors (total)
#define EEPROM_POWER_COUNT_TOT (EEPROM_FERROR_COUNT_TOT - 2) // uint16
////////////////////////////////////////
// TMC2130 Accurate sensorless homing
// X-axis home origin (stepper phase in microsteps, 0..63 for 16ustep resolution)
#define EEPROM_TMC2130_HOME_X_ORIGIN (EEPROM_POWER_COUNT_TOT - 1) // uint8
// X-axis home bsteps (number of microsteps backward)
#define EEPROM_TMC2130_HOME_X_BSTEPS (EEPROM_TMC2130_HOME_X_ORIGIN - 1) // uint8
// X-axis home fsteps (number of microsteps forward)
#define EEPROM_TMC2130_HOME_X_FSTEPS (EEPROM_TMC2130_HOME_X_BSTEPS - 1) // uint8
// Y-axis home origin (stepper phase in microsteps, 0..63 for 16ustep resolution)
#define EEPROM_TMC2130_HOME_Y_ORIGIN (EEPROM_TMC2130_HOME_X_FSTEPS - 1) // uint8
// X-axis home bsteps (number of microsteps backward)
#define EEPROM_TMC2130_HOME_Y_BSTEPS (EEPROM_TMC2130_HOME_Y_ORIGIN - 1) // uint8
// X-axis home fsteps (number of microsteps forward)
#define EEPROM_TMC2130_HOME_Y_FSTEPS (EEPROM_TMC2130_HOME_Y_BSTEPS - 1) // uint8
// Accurate homing enabled
#define EEPROM_TMC2130_HOME_ENABLED (EEPROM_TMC2130_HOME_Y_FSTEPS - 1) // uint8
////////////////////////////////////////
// TMC2130 uStep linearity correction
// Linearity correction factor (XYZE)
#define EEPROM_TMC2130_WAVE_X_FAC (EEPROM_TMC2130_HOME_ENABLED - 1) // uint8
#define EEPROM_TMC2130_WAVE_Y_FAC (EEPROM_TMC2130_WAVE_X_FAC - 1) // uint8
#define EEPROM_TMC2130_WAVE_Z_FAC (EEPROM_TMC2130_WAVE_Y_FAC - 1) // uint8
#define EEPROM_TMC2130_WAVE_E_FAC (EEPROM_TMC2130_WAVE_Z_FAC - 1) // uint8
////////////////////////////////////////
// TMC2130 uStep resolution
// microstep resolution (XYZE): usteps = (256 >> mres)
#define EEPROM_TMC2130_X_MRES (EEPROM_TMC2130_WAVE_E_FAC - 1) // uint8
#define EEPROM_TMC2130_Y_MRES (EEPROM_TMC2130_X_MRES - 1) // uint8
#define EEPROM_TMC2130_Z_MRES (EEPROM_TMC2130_Y_MRES - 1) // uint8
#define EEPROM_TMC2130_E_MRES (EEPROM_TMC2130_Z_MRES - 1) // uint8
// HW
#define EEPROM_PRINTER_TYPE (EEPROM_TMC2130_E_MRES - 2) // uint16
#define EEPROM_BOARD_TYPE (EEPROM_PRINTER_TYPE - 2) // uint16
// Extruder multiplier for power panic
#define EEPROM_EXTRUDER_MULTIPLIER_0 (EEPROM_BOARD_TYPE - 4) //float
#define EEPROM_EXTRUDER_MULTIPLIER_1 (EEPROM_EXTRUDER_MULTIPLIER_0 - 4) //float
#define EEPROM_EXTRUDER_MULTIPLIER_2 (EEPROM_EXTRUDER_MULTIPLIER_1 - 4) //float
#define EEPROM_EXTRUDEMULTIPLY (EEPROM_EXTRUDER_MULTIPLIER_2 - 2) // uint16
#define EEPROM_UVLO_TINY_CURRENT_POSITION_Z (EEPROM_EXTRUDEMULTIPLY-4) // float
#define EEPROM_UVLO_TARGET_HOTEND (EEPROM_UVLO_TINY_CURRENT_POSITION_Z-2) // uint16
// Sound Mode
#define EEPROM_SOUND_MODE (EEPROM_UVLO_TARGET_HOTEND-1) // uint8
#define EEPROM_AUTO_DEPLETE (EEPROM_SOUND_MODE-1) //bool
#define EEPROM_FSENS_OQ_MEASS_ENABLED (EEPROM_AUTO_DEPLETE - 1) //bool
#define EEPROM_MMU_FAIL_TOT (EEPROM_FSENS_OQ_MEASS_ENABLED - 2) //uint16_t
#define EEPROM_MMU_FAIL (EEPROM_MMU_FAIL_TOT - 1) //uint8_t
#define EEPROM_MMU_LOAD_FAIL_TOT (EEPROM_MMU_FAIL - 2) //uint16_t
#define EEPROM_MMU_LOAD_FAIL (EEPROM_MMU_LOAD_FAIL_TOT - 1) //uint8_t
#define EEPROM_MMU_CUTTER_ENABLED (EEPROM_MMU_LOAD_FAIL - 1)
#define EEPROM_UVLO_MESH_BED_LEVELING_FULL (EEPROM_MMU_CUTTER_ENABLED - 12*12*2) //allow 12 calibration points for future expansion
#define EEPROM_MBL_TYPE (EEPROM_UVLO_MESH_BED_LEVELING_FULL-1) //uint8_t for mesh bed leveling precision
#define EEPROM_MBL_MAGNET_ELIMINATION (EEPROM_MBL_TYPE -1)
#define EEPROM_MBL_POINTS_NR (EEPROM_MBL_MAGNET_ELIMINATION -1) //uint8_t number of points in one exis for mesh bed leveling
#define EEPROM_MBL_PROBE_NR (EEPROM_MBL_POINTS_NR-1) //number of measurements for each point
#define EEPROM_MMU_STEALTH (EEPROM_MBL_PROBE_NR-1)
#define EEPROM_CHECK_MODE (EEPROM_MMU_STEALTH-1) // uint8
#define EEPROM_NOZZLE_DIAMETER (EEPROM_CHECK_MODE-1) // uint8
#define EEPROM_NOZZLE_DIAMETER_uM (EEPROM_NOZZLE_DIAMETER-2) // uint16
#define EEPROM_CHECK_MODEL (EEPROM_NOZZLE_DIAMETER_uM-1) // uint8
#define EEPROM_CHECK_VERSION (EEPROM_CHECK_MODEL-1) // uint8
#define EEPROM_CHECK_GCODE (EEPROM_CHECK_VERSION-1) // uint8
#define EEPROM_SHEETS_BASE (EEPROM_CHECK_GCODE - EEPROM_SHEETS_SIZEOF) // Sheets
static Sheets * const EEPROM_Sheets_base = (Sheets*)(EEPROM_SHEETS_BASE);
#define EEPROM_FSENSOR_PCB (EEPROM_SHEETS_BASE-1) // uint8
#define EEPROM_FSENSOR_ACTION_NA (EEPROM_FSENSOR_PCB-1) // uint8
#define EEPROM_UVLO_SAVED_TARGET (EEPROM_FSENSOR_ACTION_NA - 4*4) // 4 x float for saved target for all axes
#define EEPROM_UVLO_FEEDMULTIPLY (EEPROM_UVLO_SAVED_TARGET - 2) // uint16_t for feedmultiply
#define EEPROM_BACKLIGHT_LEVEL_HIGH (EEPROM_UVLO_FEEDMULTIPLY-1) // uint8
#define EEPROM_BACKLIGHT_LEVEL_LOW (EEPROM_BACKLIGHT_LEVEL_HIGH-1) // uint8
#define EEPROM_BACKLIGHT_MODE (EEPROM_BACKLIGHT_LEVEL_LOW-1) // uint8
#define EEPROM_BACKLIGHT_TIMEOUT (EEPROM_BACKLIGHT_MODE-2) // uint16
#define EEPROM_UVLO_LA_K (EEPROM_BACKLIGHT_TIMEOUT-4) // float
//This is supposed to point to last item to allow EEPROM overrun check. Please update when adding new items.
#define EEPROM_LAST_ITEM EEPROM_UVLO_LA_K
// !!!!!
// !!!!! this is end of EEPROM section ... all updates MUST BE inserted before this mark !!!!!
// !!!!!
// Currently running firmware, each digit stored as uint16_t.
// The flavor differentiates a dev, alpha, beta, release candidate or a release version.
#define EEPROM_FIRMWARE_VERSION_END (FW_PRUSA3D_MAGIC_LEN+8)
#define EEPROM_FIRMWARE_VERSION_FLAVOR (FW_PRUSA3D_MAGIC_LEN+6)
#define EEPROM_FIRMWARE_VERSION_REVISION (FW_PRUSA3D_MAGIC_LEN+4)
#define EEPROM_FIRMWARE_VERSION_MINOR (FW_PRUSA3D_MAGIC_LEN+2)
#define EEPROM_FIRMWARE_VERSION_MAJOR FW_PRUSA3D_MAGIC_LEN
// Magic string, indicating that the current or the previous firmware running was the Prusa3D firmware.
#define EEPROM_FIRMWARE_PRUSA_MAGIC 0
#ifdef __cplusplus
#include "ConfigurationStore.h"
static_assert(EEPROM_FIRMWARE_VERSION_END < 20, "Firmware version EEPROM address conflicts with EEPROM_M500_base");
static constexpr M500_conf * const EEPROM_M500_base = reinterpret_cast<M500_conf*>(20); //offset for storing settings using M500
static_assert(((sizeof(M500_conf) + 20) < EEPROM_LAST_ITEM), "M500_conf address space conflicts with previous items.");
#endif
enum
{
EEPROM_MMU_CUTTER_ENABLED_enabled = 1,
EEPROM_MMU_CUTTER_ENABLED_always = 2,
};
#ifdef __cplusplus
void eeprom_init();
bool eeprom_is_sheet_initialized(uint8_t sheet_num);
struct SheetName
{
char c[sizeof(Sheet::name) + 1];
};
void eeprom_default_sheet_name(uint8_t index, SheetName &sheetName);
int8_t eeprom_next_initialized_sheet(int8_t sheet);
void eeprom_switch_to_next_sheet();
#endif
#endif // EEPROM_H
Reference in New Issue View Git Blame Copy Permalink