3DPrinting/Prusa-Firmware
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
2b3729125d
Prusa-Firmware/Firmware/thermistortables.h
Yuri D'Elia a60ed81a35 Implement MIN/MAX AMBIENT safety checks 
Take advantage of the NTC thermistor found on the Einsy as an additional
safety measure, following the steps of the other MIN/MAXTEMP errors.

Introduce two configurable params AMBIENT_MINTEMP and AMBIENT_MAXTEMP
in the variant defines and set them for the MK3/MK3S to -30/+100
respectively.

AMBIENT_MINTEMP is primarily intended to catch a defective board
thermistor (to ensure MAXTEMP would be properly triggered) and thus the
trigger temperature is set just above the sensing limit and well below
the operating range.

AMBIENT_MAXTEMP is set at 100C, which is instead 20C above the maximum
recommended operating temperature of the Einsy. The NTC thermistor is
located just above the main power connector on the bottom of the board,
and could also help in detecting a faulty connection which can result in
rapid overheating of the contacts.

As for MAXTEMP, we cut power to the heaters, print fan and motors to
reduce power draw. Resume is not possible except by resetting the
printer, since the user is highly advised to inspect the board for
problems before attempting to continue.
2020-08-01 17:38:10 +02:00

1390 lines
45 KiB
C
Raw Blame History

#ifndef THERMISTORTABLES_H_
#define THERMISTORTABLES_H_
#include "Configuration_adv.h"
#include <avr/pgmspace.h>
#define OVERSAMPLENR 16
#if (THERMISTORHEATER_0 == 1) || (THERMISTORHEATER_1 == 1) || (THERMISTORHEATER_2 == 1) || (THERMISTORBED == 1) //100k bed thermistor
const short temptable_1[][2] PROGMEM = {
{ 23*OVERSAMPLENR , 300 },
{ 25*OVERSAMPLENR , 295 },
{ 27*OVERSAMPLENR , 290 },
{ 28*OVERSAMPLENR , 285 },
{ 31*OVERSAMPLENR , 280 },
{ 33*OVERSAMPLENR , 275 },
{ 35*OVERSAMPLENR , 270 },
{ 38*OVERSAMPLENR , 265 },
{ 41*OVERSAMPLENR , 260 },
{ 44*OVERSAMPLENR , 255 },
{ 48*OVERSAMPLENR , 250 },
{ 52*OVERSAMPLENR , 245 },
{ 56*OVERSAMPLENR , 240 },
{ 61*OVERSAMPLENR , 235 },
{ 66*OVERSAMPLENR , 230 },
{ 71*OVERSAMPLENR , 225 },
{ 78*OVERSAMPLENR , 220 },
{ 84*OVERSAMPLENR , 215 },
{ 92*OVERSAMPLENR , 210 },
{ 100*OVERSAMPLENR , 205 },
{ 109*OVERSAMPLENR , 200 },
{ 120*OVERSAMPLENR , 195 },
{ 131*OVERSAMPLENR , 190 },
{ 143*OVERSAMPLENR , 185 },
{ 156*OVERSAMPLENR , 180 },
{ 171*OVERSAMPLENR , 175 },
{ 187*OVERSAMPLENR , 170 },
{ 205*OVERSAMPLENR , 165 },
{ 224*OVERSAMPLENR , 160 },
{ 245*OVERSAMPLENR , 155 },
{ 268*OVERSAMPLENR , 150 },
{ 293*OVERSAMPLENR , 145 },
{ 320*OVERSAMPLENR , 140 },
{ 348*OVERSAMPLENR , 135 },
{ 379*OVERSAMPLENR , 130 },
{ 411*OVERSAMPLENR , 125 },
{ 445*OVERSAMPLENR , 120 },
{ 480*OVERSAMPLENR , 115 },
{ 516*OVERSAMPLENR , 110 },
{ 553*OVERSAMPLENR , 105 },
{ 591*OVERSAMPLENR , 100 },
{ 628*OVERSAMPLENR , 95 },
{ 665*OVERSAMPLENR , 90 },
{ 702*OVERSAMPLENR , 85 },
{ 737*OVERSAMPLENR , 80 },
{ 770*OVERSAMPLENR , 75 },
{ 801*OVERSAMPLENR , 70 },
{ 830*OVERSAMPLENR , 65 },
{ 857*OVERSAMPLENR , 60 },
{ 881*OVERSAMPLENR , 55 },
{ 903*OVERSAMPLENR , 50 },
{ 922*OVERSAMPLENR , 45 },
{ 939*OVERSAMPLENR , 40 },
{ 954*OVERSAMPLENR , 35 },
{ 966*OVERSAMPLENR , 30 },
{ 977*OVERSAMPLENR , 25 },
{ 985*OVERSAMPLENR , 20 },
{ 993*OVERSAMPLENR , 15 },
{ 999*OVERSAMPLENR , 10 },
{ 1004*OVERSAMPLENR , 5 },
{ 1008*OVERSAMPLENR , 0 } //safety
};
#endif
#if (THERMISTORHEATER_0 == 2) || (THERMISTORHEATER_1 == 2) || (THERMISTORHEATER_2 == 2) || (THERMISTORBED == 2) //200k bed thermistor
const short temptable_2[][2] PROGMEM = {
//200k ATC Semitec 204GT-2
//Verified by linagee. Source: http://shop.arcol.hu/static/datasheets/thermistors.pdf
// Calculated using 4.7kohm pullup, voltage divider math, and manufacturer provided temp/resistance
{1*OVERSAMPLENR, 848},
{30*OVERSAMPLENR, 300}, //top rating 300C
{34*OVERSAMPLENR, 290},
{39*OVERSAMPLENR, 280},
{46*OVERSAMPLENR, 270},
{53*OVERSAMPLENR, 260},
{63*OVERSAMPLENR, 250},
{74*OVERSAMPLENR, 240},
{87*OVERSAMPLENR, 230},
{104*OVERSAMPLENR, 220},
{124*OVERSAMPLENR, 210},
{148*OVERSAMPLENR, 200},
{176*OVERSAMPLENR, 190},
{211*OVERSAMPLENR, 180},
{252*OVERSAMPLENR, 170},
{301*OVERSAMPLENR, 160},
{357*OVERSAMPLENR, 150},
{420*OVERSAMPLENR, 140},
{489*OVERSAMPLENR, 130},
{562*OVERSAMPLENR, 120},
{636*OVERSAMPLENR, 110},
{708*OVERSAMPLENR, 100},
{775*OVERSAMPLENR, 90},
{835*OVERSAMPLENR, 80},
{884*OVERSAMPLENR, 70},
{924*OVERSAMPLENR, 60},
{955*OVERSAMPLENR, 50},
{977*OVERSAMPLENR, 40},
{993*OVERSAMPLENR, 30},
{1004*OVERSAMPLENR, 20},
{1012*OVERSAMPLENR, 10},
{1016*OVERSAMPLENR, 0},
};
#endif
#if (THERMISTORHEATER_0 == 3) || (THERMISTORHEATER_1 == 3) || (THERMISTORHEATER_2 == 3) || (THERMISTORBED == 3) //mendel-parts
const short temptable_3[][2] PROGMEM = {
{1*OVERSAMPLENR,864},
{21*OVERSAMPLENR,300},
{25*OVERSAMPLENR,290},
{29*OVERSAMPLENR,280},
{33*OVERSAMPLENR,270},
{39*OVERSAMPLENR,260},
{46*OVERSAMPLENR,250},
{54*OVERSAMPLENR,240},
{64*OVERSAMPLENR,230},
{75*OVERSAMPLENR,220},
{90*OVERSAMPLENR,210},
{107*OVERSAMPLENR,200},
{128*OVERSAMPLENR,190},
{154*OVERSAMPLENR,180},
{184*OVERSAMPLENR,170},
{221*OVERSAMPLENR,160},
{265*OVERSAMPLENR,150},
{316*OVERSAMPLENR,140},
{375*OVERSAMPLENR,130},
{441*OVERSAMPLENR,120},
{513*OVERSAMPLENR,110},
{588*OVERSAMPLENR,100},
{734*OVERSAMPLENR,80},
{856*OVERSAMPLENR,60},
{938*OVERSAMPLENR,40},
{986*OVERSAMPLENR,20},
{1008*OVERSAMPLENR,0},
{1018*OVERSAMPLENR,-20}
};
#endif
#if (THERMISTORHEATER_0 == 4) || (THERMISTORHEATER_1 == 4) || (THERMISTORHEATER_2 == 4) || (THERMISTORBED == 4) //10k thermistor
const short temptable_4[][2] PROGMEM = {
{1*OVERSAMPLENR, 430},
{54*OVERSAMPLENR, 137},
{107*OVERSAMPLENR, 107},
{160*OVERSAMPLENR, 91},
{213*OVERSAMPLENR, 80},
{266*OVERSAMPLENR, 71},
{319*OVERSAMPLENR, 64},
{372*OVERSAMPLENR, 57},
{425*OVERSAMPLENR, 51},
{478*OVERSAMPLENR, 46},
{531*OVERSAMPLENR, 41},
{584*OVERSAMPLENR, 35},
{637*OVERSAMPLENR, 30},
{690*OVERSAMPLENR, 25},
{743*OVERSAMPLENR, 20},
{796*OVERSAMPLENR, 14},
{849*OVERSAMPLENR, 7},
{902*OVERSAMPLENR, 0},
{955*OVERSAMPLENR, -11},
{1008*OVERSAMPLENR, -35}
};
#endif
#if (THERMISTORHEATER_0 == 5) || (THERMISTORHEATER_1 == 5) || (THERMISTORHEATER_2 == 5) || (THERMISTORBED == 5) //100k ParCan thermistor (104GT-2)
const short temptable_5[][2] PROGMEM = {
// ATC Semitec 104GT-2 (Used in ParCan)
// Verified by linagee. Source: http://shop.arcol.hu/static/datasheets/thermistors.pdf
// Calculated using 4.7kohm pullup, voltage divider math, and manufacturer provided temp/resistance
{1*OVERSAMPLENR, 713},
{17*OVERSAMPLENR, 300}, //top rating 300C
{20*OVERSAMPLENR, 290},
{23*OVERSAMPLENR, 280},
{27*OVERSAMPLENR, 270},
{31*OVERSAMPLENR, 260},
{37*OVERSAMPLENR, 250},
{43*OVERSAMPLENR, 240},
{51*OVERSAMPLENR, 230},
{61*OVERSAMPLENR, 220},
{73*OVERSAMPLENR, 210},
{87*OVERSAMPLENR, 200},
{106*OVERSAMPLENR, 190},
{128*OVERSAMPLENR, 180},
{155*OVERSAMPLENR, 170},
{189*OVERSAMPLENR, 160},
{230*OVERSAMPLENR, 150},
{278*OVERSAMPLENR, 140},
{336*OVERSAMPLENR, 130},
{402*OVERSAMPLENR, 120},
{476*OVERSAMPLENR, 110},
{554*OVERSAMPLENR, 100},
{635*OVERSAMPLENR, 90},
{713*OVERSAMPLENR, 80},
{784*OVERSAMPLENR, 70},
{846*OVERSAMPLENR, 60},
{897*OVERSAMPLENR, 50},
{937*OVERSAMPLENR, 40},
{966*OVERSAMPLENR, 30},
{986*OVERSAMPLENR, 20},
{1000*OVERSAMPLENR, 10},
{1010*OVERSAMPLENR, 0}
};
#endif
#if (THERMISTORHEATER_0 == 6) || (THERMISTORHEATER_1 == 6) || (THERMISTORHEATER_2 == 6) || (THERMISTORBED == 6) // 100k Epcos thermistor
const short temptable_6[][2] PROGMEM = {
{1*OVERSAMPLENR, 350},
{28*OVERSAMPLENR, 250}, //top rating 250C
{31*OVERSAMPLENR, 245},
{35*OVERSAMPLENR, 240},
{39*OVERSAMPLENR, 235},
{42*OVERSAMPLENR, 230},
{44*OVERSAMPLENR, 225},
{49*OVERSAMPLENR, 220},
{53*OVERSAMPLENR, 215},
{62*OVERSAMPLENR, 210},
{71*OVERSAMPLENR, 205}, //fitted graphically
{78*OVERSAMPLENR, 200}, //fitted graphically
{94*OVERSAMPLENR, 190},
{102*OVERSAMPLENR, 185},
{116*OVERSAMPLENR, 170},
{143*OVERSAMPLENR, 160},
{183*OVERSAMPLENR, 150},
{223*OVERSAMPLENR, 140},
{270*OVERSAMPLENR, 130},
{318*OVERSAMPLENR, 120},
{383*OVERSAMPLENR, 110},
{413*OVERSAMPLENR, 105},
{439*OVERSAMPLENR, 100},
{484*OVERSAMPLENR, 95},
{513*OVERSAMPLENR, 90},
{607*OVERSAMPLENR, 80},
{664*OVERSAMPLENR, 70},
{781*OVERSAMPLENR, 60},
{810*OVERSAMPLENR, 55},
{849*OVERSAMPLENR, 50},
{914*OVERSAMPLENR, 45},
{914*OVERSAMPLENR, 40},
{935*OVERSAMPLENR, 35},
{954*OVERSAMPLENR, 30},
{970*OVERSAMPLENR, 25},
{978*OVERSAMPLENR, 22},
{1008*OVERSAMPLENR, 3},
{1023*OVERSAMPLENR, 0} //to allow internal 0 degrees C
};
#endif
#if (THERMISTORHEATER_0 == 7) || (THERMISTORHEATER_1 == 7) || (THERMISTORHEATER_2 == 7) || (THERMISTORBED == 7) // 100k Honeywell 135-104LAG-J01
const short temptable_7[][2] PROGMEM = {
{1*OVERSAMPLENR, 941},
{19*OVERSAMPLENR, 362},
{37*OVERSAMPLENR, 299}, //top rating 300C
{55*OVERSAMPLENR, 266},
{73*OVERSAMPLENR, 245},
{91*OVERSAMPLENR, 229},
{109*OVERSAMPLENR, 216},
{127*OVERSAMPLENR, 206},
{145*OVERSAMPLENR, 197},
{163*OVERSAMPLENR, 190},
{181*OVERSAMPLENR, 183},
{199*OVERSAMPLENR, 177},
{217*OVERSAMPLENR, 171},
{235*OVERSAMPLENR, 166},
{253*OVERSAMPLENR, 162},
{271*OVERSAMPLENR, 157},
{289*OVERSAMPLENR, 153},
{307*OVERSAMPLENR, 149},
{325*OVERSAMPLENR, 146},
{343*OVERSAMPLENR, 142},
{361*OVERSAMPLENR, 139},
{379*OVERSAMPLENR, 135},
{397*OVERSAMPLENR, 132},
{415*OVERSAMPLENR, 129},
{433*OVERSAMPLENR, 126},
{451*OVERSAMPLENR, 123},
{469*OVERSAMPLENR, 121},
{487*OVERSAMPLENR, 118},
{505*OVERSAMPLENR, 115},
{523*OVERSAMPLENR, 112},
{541*OVERSAMPLENR, 110},
{559*OVERSAMPLENR, 107},
{577*OVERSAMPLENR, 105},
{595*OVERSAMPLENR, 102},
{613*OVERSAMPLENR, 99},
{631*OVERSAMPLENR, 97},
{649*OVERSAMPLENR, 94},
{667*OVERSAMPLENR, 92},
{685*OVERSAMPLENR, 89},
{703*OVERSAMPLENR, 86},
{721*OVERSAMPLENR, 84},
{739*OVERSAMPLENR, 81},
{757*OVERSAMPLENR, 78},
{775*OVERSAMPLENR, 75},
{793*OVERSAMPLENR, 72},
{811*OVERSAMPLENR, 69},
{829*OVERSAMPLENR, 66},
{847*OVERSAMPLENR, 62},
{865*OVERSAMPLENR, 59},
{883*OVERSAMPLENR, 55},
{901*OVERSAMPLENR, 51},
{919*OVERSAMPLENR, 46},
{937*OVERSAMPLENR, 41},
{955*OVERSAMPLENR, 35},
{973*OVERSAMPLENR, 27},
{991*OVERSAMPLENR, 17},
{1009*OVERSAMPLENR, 1},
{1023*OVERSAMPLENR, 0} //to allow internal 0 degrees C
};
#endif
#if (THERMISTORHEATER_0 == 71) || (THERMISTORHEATER_1 == 71) || (THERMISTORHEATER_2 == 71) || (THERMISTORBED == 71) // 100k Honeywell 135-104LAF-J01
// R0 = 100000 Ohm
// T0 = 25 °C
// Beta = 3974
// R1 = 0 Ohm
// R2 = 4700 Ohm
const short temptable_71[][2] PROGMEM = {
{35*OVERSAMPLENR, 300},
{51*OVERSAMPLENR, 270},
{54*OVERSAMPLENR, 265},
{58*OVERSAMPLENR, 260},
{59*OVERSAMPLENR, 258},
{61*OVERSAMPLENR, 256},
{63*OVERSAMPLENR, 254},
{64*OVERSAMPLENR, 252},
{66*OVERSAMPLENR, 250},
{67*OVERSAMPLENR, 249},
{68*OVERSAMPLENR, 248},
{69*OVERSAMPLENR, 247},
{70*OVERSAMPLENR, 246},
{71*OVERSAMPLENR, 245},
{72*OVERSAMPLENR, 244},
{73*OVERSAMPLENR, 243},
{74*OVERSAMPLENR, 242},
{75*OVERSAMPLENR, 241},
{76*OVERSAMPLENR, 240},
{77*OVERSAMPLENR, 239},
{78*OVERSAMPLENR, 238},
{79*OVERSAMPLENR, 237},
{80*OVERSAMPLENR, 236},
{81*OVERSAMPLENR, 235},
{82*OVERSAMPLENR, 234},
{84*OVERSAMPLENR, 233},
{85*OVERSAMPLENR, 232},
{86*OVERSAMPLENR, 231},
{87*OVERSAMPLENR, 230},
{89*OVERSAMPLENR, 229},
{90*OVERSAMPLENR, 228},
{91*OVERSAMPLENR, 227},
{92*OVERSAMPLENR, 226},
{94*OVERSAMPLENR, 225},
{95*OVERSAMPLENR, 224},
{97*OVERSAMPLENR, 223},
{98*OVERSAMPLENR, 222},
{99*OVERSAMPLENR, 221},
{101*OVERSAMPLENR, 220},
{102*OVERSAMPLENR, 219},
{104*OVERSAMPLENR, 218},
{106*OVERSAMPLENR, 217},
{107*OVERSAMPLENR, 216},
{109*OVERSAMPLENR, 215},
{110*OVERSAMPLENR, 214},
{112*OVERSAMPLENR, 213},
{114*OVERSAMPLENR, 212},
{115*OVERSAMPLENR, 211},
{117*OVERSAMPLENR, 210},
{119*OVERSAMPLENR, 209},
{121*OVERSAMPLENR, 208},
{123*OVERSAMPLENR, 207},
{125*OVERSAMPLENR, 206},
{126*OVERSAMPLENR, 205},
{128*OVERSAMPLENR, 204},
{130*OVERSAMPLENR, 203},
{132*OVERSAMPLENR, 202},
{134*OVERSAMPLENR, 201},
{136*OVERSAMPLENR, 200},
{139*OVERSAMPLENR, 199},
{141*OVERSAMPLENR, 198},
{143*OVERSAMPLENR, 197},
{145*OVERSAMPLENR, 196},
{147*OVERSAMPLENR, 195},
{150*OVERSAMPLENR, 194},
{152*OVERSAMPLENR, 193},
{154*OVERSAMPLENR, 192},
{157*OVERSAMPLENR, 191},
{159*OVERSAMPLENR, 190},
{162*OVERSAMPLENR, 189},
{164*OVERSAMPLENR, 188},
{167*OVERSAMPLENR, 187},
{170*OVERSAMPLENR, 186},
{172*OVERSAMPLENR, 185},
{175*OVERSAMPLENR, 184},
{178*OVERSAMPLENR, 183},
{181*OVERSAMPLENR, 182},
{184*OVERSAMPLENR, 181},
{187*OVERSAMPLENR, 180},
{190*OVERSAMPLENR, 179},
{193*OVERSAMPLENR, 178},
{196*OVERSAMPLENR, 177},
{199*OVERSAMPLENR, 176},
{202*OVERSAMPLENR, 175},
{205*OVERSAMPLENR, 174},
{208*OVERSAMPLENR, 173},
{212*OVERSAMPLENR, 172},
{215*OVERSAMPLENR, 171},
{219*OVERSAMPLENR, 170},
{237*OVERSAMPLENR, 165},
{256*OVERSAMPLENR, 160},
{300*OVERSAMPLENR, 150},
{351*OVERSAMPLENR, 140},
{470*OVERSAMPLENR, 120},
{504*OVERSAMPLENR, 115},
{538*OVERSAMPLENR, 110},
{552*OVERSAMPLENR, 108},
{566*OVERSAMPLENR, 106},
{580*OVERSAMPLENR, 104},
{594*OVERSAMPLENR, 102},
{608*OVERSAMPLENR, 100},
{622*OVERSAMPLENR, 98},
{636*OVERSAMPLENR, 96},
{650*OVERSAMPLENR, 94},
{664*OVERSAMPLENR, 92},
{678*OVERSAMPLENR, 90},
{712*OVERSAMPLENR, 85},
{745*OVERSAMPLENR, 80},
{758*OVERSAMPLENR, 78},
{770*OVERSAMPLENR, 76},
{783*OVERSAMPLENR, 74},
{795*OVERSAMPLENR, 72},
{806*OVERSAMPLENR, 70},
{818*OVERSAMPLENR, 68},
{829*OVERSAMPLENR, 66},
{840*OVERSAMPLENR, 64},
{850*OVERSAMPLENR, 62},
{860*OVERSAMPLENR, 60},
{870*OVERSAMPLENR, 58},
{879*OVERSAMPLENR, 56},
{888*OVERSAMPLENR, 54},
{897*OVERSAMPLENR, 52},
{905*OVERSAMPLENR, 50},
{924*OVERSAMPLENR, 45},
{940*OVERSAMPLENR, 40},
{955*OVERSAMPLENR, 35},
{967*OVERSAMPLENR, 30},
{970*OVERSAMPLENR, 29},
{972*OVERSAMPLENR, 28},
{974*OVERSAMPLENR, 27},
{976*OVERSAMPLENR, 26},
{978*OVERSAMPLENR, 25},
{980*OVERSAMPLENR, 24},
{982*OVERSAMPLENR, 23},
{984*OVERSAMPLENR, 22},
{985*OVERSAMPLENR, 21},
{987*OVERSAMPLENR, 20},
{995*OVERSAMPLENR, 15},
{1001*OVERSAMPLENR, 10},
{1006*OVERSAMPLENR, 5},
{1010*OVERSAMPLENR, 0},
};
#endif
#if (THERMISTORHEATER_0 == 8) || (THERMISTORHEATER_1 == 8) || (THERMISTORHEATER_2 == 8) || (THERMISTORBED == 8)
// 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
const short temptable_8[][2] PROGMEM = {
{1*OVERSAMPLENR, 704},
{54*OVERSAMPLENR, 216},
{107*OVERSAMPLENR, 175},
{160*OVERSAMPLENR, 152},
{213*OVERSAMPLENR, 137},
{266*OVERSAMPLENR, 125},
{319*OVERSAMPLENR, 115},
{372*OVERSAMPLENR, 106},
{425*OVERSAMPLENR, 99},
{478*OVERSAMPLENR, 91},
{531*OVERSAMPLENR, 85},
{584*OVERSAMPLENR, 78},
{637*OVERSAMPLENR, 71},
{690*OVERSAMPLENR, 65},
{743*OVERSAMPLENR, 58},
{796*OVERSAMPLENR, 50},
{849*OVERSAMPLENR, 42},
{902*OVERSAMPLENR, 31},
{955*OVERSAMPLENR, 17},
{1008*OVERSAMPLENR, 0}
};
#endif
#if (THERMISTORHEATER_0 == 9) || (THERMISTORHEATER_1 == 9) || (THERMISTORHEATER_2 == 9) || (THERMISTORBED == 9)
// 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
const short temptable_9[][2] PROGMEM = {
{1*OVERSAMPLENR, 936},
{36*OVERSAMPLENR, 300},
{71*OVERSAMPLENR, 246},
{106*OVERSAMPLENR, 218},
{141*OVERSAMPLENR, 199},
{176*OVERSAMPLENR, 185},
{211*OVERSAMPLENR, 173},
{246*OVERSAMPLENR, 163},
{281*OVERSAMPLENR, 155},
{316*OVERSAMPLENR, 147},
{351*OVERSAMPLENR, 140},
{386*OVERSAMPLENR, 134},
{421*OVERSAMPLENR, 128},
{456*OVERSAMPLENR, 122},
{491*OVERSAMPLENR, 117},
{526*OVERSAMPLENR, 112},
{561*OVERSAMPLENR, 107},
{596*OVERSAMPLENR, 102},
{631*OVERSAMPLENR, 97},
{666*OVERSAMPLENR, 92},
{701*OVERSAMPLENR, 87},
{736*OVERSAMPLENR, 81},
{771*OVERSAMPLENR, 76},
{806*OVERSAMPLENR, 70},
{841*OVERSAMPLENR, 63},
{876*OVERSAMPLENR, 56},
{911*OVERSAMPLENR, 48},
{946*OVERSAMPLENR, 38},
{981*OVERSAMPLENR, 23},
{1005*OVERSAMPLENR, 5},
{1016*OVERSAMPLENR, 0}
};
#endif
#if (THERMISTORHEATER_0 == 10) || (THERMISTORHEATER_1 == 10) || (THERMISTORHEATER_2 == 10) || (THERMISTORBED == 10)
// 100k RS thermistor 198-961 (4.7k pullup)
const short temptable_10[][2] PROGMEM = {
{1*OVERSAMPLENR, 929},
{36*OVERSAMPLENR, 299},
{71*OVERSAMPLENR, 246},
{106*OVERSAMPLENR, 217},
{141*OVERSAMPLENR, 198},
{176*OVERSAMPLENR, 184},
{211*OVERSAMPLENR, 173},
{246*OVERSAMPLENR, 163},
{281*OVERSAMPLENR, 154},
{316*OVERSAMPLENR, 147},
{351*OVERSAMPLENR, 140},
{386*OVERSAMPLENR, 134},
{421*OVERSAMPLENR, 128},
{456*OVERSAMPLENR, 122},
{491*OVERSAMPLENR, 117},
{526*OVERSAMPLENR, 112},
{561*OVERSAMPLENR, 107},
{596*OVERSAMPLENR, 102},
{631*OVERSAMPLENR, 97},
{666*OVERSAMPLENR, 91},
{701*OVERSAMPLENR, 86},
{736*OVERSAMPLENR, 81},
{771*OVERSAMPLENR, 76},
{806*OVERSAMPLENR, 70},
{841*OVERSAMPLENR, 63},
{876*OVERSAMPLENR, 56},
{911*OVERSAMPLENR, 48},
{946*OVERSAMPLENR, 38},
{981*OVERSAMPLENR, 23},
{1005*OVERSAMPLENR, 5},
{1016*OVERSAMPLENR, 0}
};
#endif
#if (THERMISTORHEATER_0 == 11) || (THERMISTORHEATER_1 == 11) || (THERMISTORHEATER_2 == 11) || (THERMISTORBED == 11)
// QU-BD silicone bed QWG-104F-3950 thermistor
const short temptable_11[][2] PROGMEM = {
{1*OVERSAMPLENR, 938},
{31*OVERSAMPLENR, 314},
{41*OVERSAMPLENR, 290},
{51*OVERSAMPLENR, 272},
{61*OVERSAMPLENR, 258},
{71*OVERSAMPLENR, 247},
{81*OVERSAMPLENR, 237},
{91*OVERSAMPLENR, 229},
{101*OVERSAMPLENR, 221},
{111*OVERSAMPLENR, 215},
{121*OVERSAMPLENR, 209},
{131*OVERSAMPLENR, 204},
{141*OVERSAMPLENR, 199},
{151*OVERSAMPLENR, 195},
{161*OVERSAMPLENR, 190},
{171*OVERSAMPLENR, 187},
{181*OVERSAMPLENR, 183},
{191*OVERSAMPLENR, 179},
{201*OVERSAMPLENR, 176},
{221*OVERSAMPLENR, 170},
{241*OVERSAMPLENR, 165},
{261*OVERSAMPLENR, 160},
{281*OVERSAMPLENR, 155},
{301*OVERSAMPLENR, 150},
{331*OVERSAMPLENR, 144},
{361*OVERSAMPLENR, 139},
{391*OVERSAMPLENR, 133},
{421*OVERSAMPLENR, 128},
{451*OVERSAMPLENR, 123},
{491*OVERSAMPLENR, 117},
{531*OVERSAMPLENR, 111},
{571*OVERSAMPLENR, 105},
{611*OVERSAMPLENR, 100},
{641*OVERSAMPLENR, 95},
{681*OVERSAMPLENR, 90},
{711*OVERSAMPLENR, 85},
{751*OVERSAMPLENR, 79},
{791*OVERSAMPLENR, 72},
{811*OVERSAMPLENR, 69},
{831*OVERSAMPLENR, 65},
{871*OVERSAMPLENR, 57},
{881*OVERSAMPLENR, 55},
{901*OVERSAMPLENR, 51},
{921*OVERSAMPLENR, 45},
{941*OVERSAMPLENR, 39},
{971*OVERSAMPLENR, 28},
{981*OVERSAMPLENR, 23},
{991*OVERSAMPLENR, 17},
{1001*OVERSAMPLENR, 9},
{1021*OVERSAMPLENR, -27}
};
#endif
#if (THERMISTORHEATER_0 == 13) || (THERMISTORHEATER_1 == 13) || (THERMISTORHEATER_2 == 13) || (THERMISTORBED == 13)
// Hisens thermistor B25/50 =3950 +/-1%
const short temptable_13[][2] PROGMEM = {
{ 22.5*OVERSAMPLENR, 300 },
{ 24.125*OVERSAMPLENR, 295 },
{ 25.875*OVERSAMPLENR, 290 },
{ 27.8125*OVERSAMPLENR, 285 },
{ 29.9375*OVERSAMPLENR, 280 },
{ 32.25*OVERSAMPLENR, 275 },
{ 34.8125*OVERSAMPLENR, 270 },
{ 37.625*OVERSAMPLENR, 265 },
{ 40.6875*OVERSAMPLENR, 260 },
{ 44.0625*OVERSAMPLENR, 255 },
{ 47.75*OVERSAMPLENR, 250 },
{ 51.8125*OVERSAMPLENR, 245 },
{ 56.3125*OVERSAMPLENR, 240 },
{ 61.25*OVERSAMPLENR, 235 },
{ 66.75*OVERSAMPLENR, 230 },
{ 72.8125*OVERSAMPLENR, 225 },
{ 79.5*OVERSAMPLENR, 220 },
{ 87*OVERSAMPLENR, 215 },
{ 95.3125*OVERSAMPLENR, 210 },
{ 104.1875*OVERSAMPLENR, 205 },
{ 112.75*OVERSAMPLENR, 200 },
{ 123.125*OVERSAMPLENR, 195 },
{ 135.75*OVERSAMPLENR, 190 },
{ 148.3125*OVERSAMPLENR, 185 },
{ 163.8125*OVERSAMPLENR, 180 },
{ 179*OVERSAMPLENR, 175 },
{ 211.125*OVERSAMPLENR, 170 },
{ 216.125*OVERSAMPLENR, 165 },
{ 236.5625*OVERSAMPLENR, 160 },
{ 258.5*OVERSAMPLENR, 155 },
{ 279.875*OVERSAMPLENR, 150 },
{ 305.375*OVERSAMPLENR, 145 },
{ 333.25*OVERSAMPLENR, 140 },
{ 362.5625*OVERSAMPLENR, 135 },
{ 393.6875*OVERSAMPLENR, 130 },
{ 425*OVERSAMPLENR, 125 },
{ 460.625*OVERSAMPLENR, 120 },
{ 495.1875*OVERSAMPLENR, 115 },
{ 530.875*OVERSAMPLENR, 110 },
{ 567.25*OVERSAMPLENR, 105 },
{ 601.625*OVERSAMPLENR, 100 },
{ 637.875*OVERSAMPLENR, 95 },
{ 674.5625*OVERSAMPLENR, 90 },
{ 710*OVERSAMPLENR, 85 },
{ 744.125*OVERSAMPLENR, 80 },
{ 775.9375*OVERSAMPLENR, 75 },
{ 806.875*OVERSAMPLENR, 70 },
{ 835.1875*OVERSAMPLENR, 65 },
{ 861.125*OVERSAMPLENR, 60 },
{ 884.375*OVERSAMPLENR, 55 },
{ 904.5625*OVERSAMPLENR, 50 },
{ 923.8125*OVERSAMPLENR, 45 },
{ 940.375*OVERSAMPLENR, 40 },
{ 954.625*OVERSAMPLENR, 35 },
{ 966.875*OVERSAMPLENR, 30 },
{ 977.0625*OVERSAMPLENR, 25 },
{ 986*OVERSAMPLENR, 20 },
{ 993.375*OVERSAMPLENR, 15 },
{ 999.5*OVERSAMPLENR, 10 },
{ 1004.5*OVERSAMPLENR, 5 },
{ 1008.5*OVERSAMPLENR, 0 }
};
#endif
#if (THERMISTORHEATER_0 == 20) || (THERMISTORHEATER_1 == 20) || (THERMISTORHEATER_2 == 20) || (THERMISTORBED == 20) // PT100 with INA826 amp on Ultimaker v2.0 electronics
/* The PT100 in the Ultimaker v2.0 electronics has a high sample value for a high temperature.
This does not match the normal thermistor behaviour so we need to set the following defines */
#if (THERMISTORHEATER_0 == 20)
# define HEATER_0_RAW_HI_TEMP 16383
# define HEATER_0_RAW_LO_TEMP 0
#endif
#if (THERMISTORHEATER_1 == 20)
# define HEATER_1_RAW_HI_TEMP 16383
# define HEATER_1_RAW_LO_TEMP 0
#endif
#if (THERMISTORHEATER_2 == 20)
# define HEATER_2_RAW_HI_TEMP 16383
# define HEATER_2_RAW_LO_TEMP 0
#endif
#if (THERMISTORBED == 20)
# define HEATER_BED_RAW_HI_TEMP 16383
# define HEATER_BED_RAW_LO_TEMP 0
#endif
const short temptable_20[][2] PROGMEM = {
{ 0*OVERSAMPLENR , 0 },
{ 227*OVERSAMPLENR , 1 },
{ 236*OVERSAMPLENR , 10 },
{ 245*OVERSAMPLENR , 20 },
{ 253*OVERSAMPLENR , 30 },
{ 262*OVERSAMPLENR , 40 },
{ 270*OVERSAMPLENR , 50 },
{ 279*OVERSAMPLENR , 60 },
{ 287*OVERSAMPLENR , 70 },
{ 295*OVERSAMPLENR , 80 },
{ 304*OVERSAMPLENR , 90 },
{ 312*OVERSAMPLENR , 100 },
{ 320*OVERSAMPLENR , 110 },
{ 329*OVERSAMPLENR , 120 },
{ 337*OVERSAMPLENR , 130 },
{ 345*OVERSAMPLENR , 140 },
{ 353*OVERSAMPLENR , 150 },
{ 361*OVERSAMPLENR , 160 },
{ 369*OVERSAMPLENR , 170 },
{ 377*OVERSAMPLENR , 180 },
{ 385*OVERSAMPLENR , 190 },
{ 393*OVERSAMPLENR , 200 },
{ 401*OVERSAMPLENR , 210 },
{ 409*OVERSAMPLENR , 220 },
{ 417*OVERSAMPLENR , 230 },
{ 424*OVERSAMPLENR , 240 },
{ 432*OVERSAMPLENR , 250 },
{ 440*OVERSAMPLENR , 260 },
{ 447*OVERSAMPLENR , 270 },
{ 455*OVERSAMPLENR , 280 },
{ 463*OVERSAMPLENR , 290 },
{ 470*OVERSAMPLENR , 300 },
{ 478*OVERSAMPLENR , 310 },
{ 485*OVERSAMPLENR , 320 },
{ 493*OVERSAMPLENR , 330 },
{ 500*OVERSAMPLENR , 340 },
{ 507*OVERSAMPLENR , 350 },
{ 515*OVERSAMPLENR , 360 },
{ 522*OVERSAMPLENR , 370 },
{ 529*OVERSAMPLENR , 380 },
{ 537*OVERSAMPLENR , 390 },
{ 544*OVERSAMPLENR , 400 },
{ 614*OVERSAMPLENR , 500 },
{ 681*OVERSAMPLENR , 600 },
{ 744*OVERSAMPLENR , 700 },
{ 805*OVERSAMPLENR , 800 },
{ 862*OVERSAMPLENR , 900 },
{ 917*OVERSAMPLENR , 1000 },
{ 968*OVERSAMPLENR , 1100 }
};
#endif
#if (THERMISTORHEATER_0 == 51) || (THERMISTORHEATER_1 == 51) || (THERMISTORHEATER_2 == 51) || (THERMISTORBED == 51)
// 100k EPCOS (WITH 1kohm RESISTOR FOR PULLUP, R9 ON SANGUINOLOLU! NOT FOR 4.7kohm PULLUP! THIS IS NOT NORMAL!)
// Verified by linagee.
// Calculated using 1kohm pullup, voltage divider math, and manufacturer provided temp/resistance
// Advantage: Twice the resolution and better linearity from 150C to 200C
const short temptable_51[][2] PROGMEM = {
{1*OVERSAMPLENR, 350},
{190*OVERSAMPLENR, 250}, //top rating 250C
{203*OVERSAMPLENR, 245},
{217*OVERSAMPLENR, 240},
{232*OVERSAMPLENR, 235},
{248*OVERSAMPLENR, 230},
{265*OVERSAMPLENR, 225},
{283*OVERSAMPLENR, 220},
{302*OVERSAMPLENR, 215},
{322*OVERSAMPLENR, 210},
{344*OVERSAMPLENR, 205},
{366*OVERSAMPLENR, 200},
{390*OVERSAMPLENR, 195},
{415*OVERSAMPLENR, 190},
{440*OVERSAMPLENR, 185},
{467*OVERSAMPLENR, 180},
{494*OVERSAMPLENR, 175},
{522*OVERSAMPLENR, 170},
{551*OVERSAMPLENR, 165},
{580*OVERSAMPLENR, 160},
{609*OVERSAMPLENR, 155},
{638*OVERSAMPLENR, 150},
{666*OVERSAMPLENR, 145},
{695*OVERSAMPLENR, 140},
{722*OVERSAMPLENR, 135},
{749*OVERSAMPLENR, 130},
{775*OVERSAMPLENR, 125},
{800*OVERSAMPLENR, 120},
{823*OVERSAMPLENR, 115},
{845*OVERSAMPLENR, 110},
{865*OVERSAMPLENR, 105},
{884*OVERSAMPLENR, 100},
{901*OVERSAMPLENR, 95},
{917*OVERSAMPLENR, 90},
{932*OVERSAMPLENR, 85},
{944*OVERSAMPLENR, 80},
{956*OVERSAMPLENR, 75},
{966*OVERSAMPLENR, 70},
{975*OVERSAMPLENR, 65},
{982*OVERSAMPLENR, 60},
{989*OVERSAMPLENR, 55},
{995*OVERSAMPLENR, 50},
{1000*OVERSAMPLENR, 45},
{1004*OVERSAMPLENR, 40},
{1007*OVERSAMPLENR, 35},
{1010*OVERSAMPLENR, 30},
{1013*OVERSAMPLENR, 25},
{1015*OVERSAMPLENR, 20},
{1017*OVERSAMPLENR, 15},
{1018*OVERSAMPLENR, 10},
{1019*OVERSAMPLENR, 5},
{1020*OVERSAMPLENR, 0},
{1021*OVERSAMPLENR, -5}
};
#endif
#if (THERMISTORHEATER_0 == 52) || (THERMISTORHEATER_1 == 52) || (THERMISTORHEATER_2 == 52) || (THERMISTORBED == 52)
// 200k ATC Semitec 204GT-2 (WITH 1kohm RESISTOR FOR PULLUP, R9 ON SANGUINOLOLU! NOT FOR 4.7kohm PULLUP! THIS IS NOT NORMAL!)
// Verified by linagee. Source: http://shop.arcol.hu/static/datasheets/thermistors.pdf
// Calculated using 1kohm pullup, voltage divider math, and manufacturer provided temp/resistance
// Advantage: More resolution and better linearity from 150C to 200C
const short temptable_52[][2] PROGMEM = {
{1*OVERSAMPLENR, 500},
{125*OVERSAMPLENR, 300}, //top rating 300C
{142*OVERSAMPLENR, 290},
{162*OVERSAMPLENR, 280},
{185*OVERSAMPLENR, 270},
{211*OVERSAMPLENR, 260},
{240*OVERSAMPLENR, 250},
{274*OVERSAMPLENR, 240},
{312*OVERSAMPLENR, 230},
{355*OVERSAMPLENR, 220},
{401*OVERSAMPLENR, 210},
{452*OVERSAMPLENR, 200},
{506*OVERSAMPLENR, 190},
{563*OVERSAMPLENR, 180},
{620*OVERSAMPLENR, 170},
{677*OVERSAMPLENR, 160},
{732*OVERSAMPLENR, 150},
{783*OVERSAMPLENR, 140},
{830*OVERSAMPLENR, 130},
{871*OVERSAMPLENR, 120},
{906*OVERSAMPLENR, 110},
{935*OVERSAMPLENR, 100},
{958*OVERSAMPLENR, 90},
{976*OVERSAMPLENR, 80},
{990*OVERSAMPLENR, 70},
{1000*OVERSAMPLENR, 60},
{1008*OVERSAMPLENR, 50},
{1013*OVERSAMPLENR, 40},
{1017*OVERSAMPLENR, 30},
{1019*OVERSAMPLENR, 20},
{1021*OVERSAMPLENR, 10},
{1022*OVERSAMPLENR, 0}
};
#endif
#if (THERMISTORHEATER_0 == 55) || (THERMISTORHEATER_1 == 55) || (THERMISTORHEATER_2 == 55) || (THERMISTORBED == 55)
// 100k ATC Semitec 104GT-2 (Used on ParCan) (WITH 1kohm RESISTOR FOR PULLUP, R9 ON SANGUINOLOLU! NOT FOR 4.7kohm PULLUP! THIS IS NOT NORMAL!)
// Verified by linagee. Source: http://shop.arcol.hu/static/datasheets/thermistors.pdf
// Calculated using 1kohm pullup, voltage divider math, and manufacturer provided temp/resistance
// Advantage: More resolution and better linearity from 150C to 200C
const short temptable_55[][2] PROGMEM = {
{1*OVERSAMPLENR, 500},
{76*OVERSAMPLENR, 300},
{87*OVERSAMPLENR, 290},
{100*OVERSAMPLENR, 280},
{114*OVERSAMPLENR, 270},
{131*OVERSAMPLENR, 260},
{152*OVERSAMPLENR, 250},
{175*OVERSAMPLENR, 240},
{202*OVERSAMPLENR, 230},
{234*OVERSAMPLENR, 220},
{271*OVERSAMPLENR, 210},
{312*OVERSAMPLENR, 200},
{359*OVERSAMPLENR, 190},
{411*OVERSAMPLENR, 180},
{467*OVERSAMPLENR, 170},
{527*OVERSAMPLENR, 160},
{590*OVERSAMPLENR, 150},
{652*OVERSAMPLENR, 140},
{713*OVERSAMPLENR, 130},
{770*OVERSAMPLENR, 120},
{822*OVERSAMPLENR, 110},
{867*OVERSAMPLENR, 100},
{905*OVERSAMPLENR, 90},
{936*OVERSAMPLENR, 80},
{961*OVERSAMPLENR, 70},
{979*OVERSAMPLENR, 60},
{993*OVERSAMPLENR, 50},
{1003*OVERSAMPLENR, 40},
{1010*OVERSAMPLENR, 30},
{1015*OVERSAMPLENR, 20},
{1018*OVERSAMPLENR, 10},
{1020*OVERSAMPLENR, 0}
};
#endif
#if (THERMISTORHEATER_0 == 60) || (THERMISTORHEATER_1 == 60) || (THERMISTORHEATER_2 == 60) || (THERMISTORBED == 60) // Maker's Tool Works Kapton Bed Thermister
// ./createTemperatureLookup.py --r0=100000 --t0=25 --r1=0 --r2=4700 --beta=3950
// r0: 100000
// t0: 25
// r1: 0 (parallel with rTherm)
// r2: 4700 (series with rTherm)
// beta: 3950
// min adc: 1 at 0.0048828125 V
// max adc: 1023 at 4.9951171875 V
const short temptable_60[][2] PROGMEM = {
{51*OVERSAMPLENR, 272},
{61*OVERSAMPLENR, 258},
{71*OVERSAMPLENR, 247},
{81*OVERSAMPLENR, 237},
{91*OVERSAMPLENR, 229},
{101*OVERSAMPLENR, 221},
{131*OVERSAMPLENR, 204},
{161*OVERSAMPLENR, 190},
{191*OVERSAMPLENR, 179},
{231*OVERSAMPLENR, 167},
{271*OVERSAMPLENR, 157},
{311*OVERSAMPLENR, 148},
{351*OVERSAMPLENR, 140},
{381*OVERSAMPLENR, 135},
{411*OVERSAMPLENR, 130},
{441*OVERSAMPLENR, 125},
{451*OVERSAMPLENR, 123},
{461*OVERSAMPLENR, 122},
{471*OVERSAMPLENR, 120},
{481*OVERSAMPLENR, 119},
{491*OVERSAMPLENR, 117},
{501*OVERSAMPLENR, 116},
{511*OVERSAMPLENR, 114},
{521*OVERSAMPLENR, 113},
{531*OVERSAMPLENR, 111},
{541*OVERSAMPLENR, 110},
{551*OVERSAMPLENR, 108},
{561*OVERSAMPLENR, 107},
{571*OVERSAMPLENR, 105},
{581*OVERSAMPLENR, 104},
{591*OVERSAMPLENR, 102},
{601*OVERSAMPLENR, 101},
{611*OVERSAMPLENR, 100},
{621*OVERSAMPLENR, 98},
{631*OVERSAMPLENR, 97},
{641*OVERSAMPLENR, 95},
{651*OVERSAMPLENR, 94},
{661*OVERSAMPLENR, 92},
{671*OVERSAMPLENR, 91},
{681*OVERSAMPLENR, 90},
{691*OVERSAMPLENR, 88},
{701*OVERSAMPLENR, 87},
{711*OVERSAMPLENR, 85},
{721*OVERSAMPLENR, 84},
{731*OVERSAMPLENR, 82},
{741*OVERSAMPLENR, 81},
{751*OVERSAMPLENR, 79},
{761*OVERSAMPLENR, 77},
{771*OVERSAMPLENR, 76},
{781*OVERSAMPLENR, 74},
{791*OVERSAMPLENR, 72},
{801*OVERSAMPLENR, 71},
{811*OVERSAMPLENR, 69},
{821*OVERSAMPLENR, 67},
{831*OVERSAMPLENR, 65},
{841*OVERSAMPLENR, 63},
{851*OVERSAMPLENR, 62},
{861*OVERSAMPLENR, 60},
{871*OVERSAMPLENR, 57},
{881*OVERSAMPLENR, 55},
{891*OVERSAMPLENR, 53},
{901*OVERSAMPLENR, 51},
{911*OVERSAMPLENR, 48},
{921*OVERSAMPLENR, 45},
{931*OVERSAMPLENR, 42},
{941*OVERSAMPLENR, 39},
{951*OVERSAMPLENR, 36},
{961*OVERSAMPLENR, 32},
{981*OVERSAMPLENR, 23},
{991*OVERSAMPLENR, 17},
{1001*OVERSAMPLENR, 9},
{1008*OVERSAMPLENR, 0},
};
#endif
#if (THERMISTORBED == 12)
//100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
const short temptable_12[][2] PROGMEM = {
{35*OVERSAMPLENR, 180}, //top rating 180C
{211*OVERSAMPLENR, 140},
{233*OVERSAMPLENR, 135},
{261*OVERSAMPLENR, 130},
{290*OVERSAMPLENR, 125},
{328*OVERSAMPLENR, 120},
{362*OVERSAMPLENR, 115},
{406*OVERSAMPLENR, 110},
{446*OVERSAMPLENR, 105},
{496*OVERSAMPLENR, 100},
{539*OVERSAMPLENR, 95},
{585*OVERSAMPLENR, 90},
{629*OVERSAMPLENR, 85},
{675*OVERSAMPLENR, 80},
{718*OVERSAMPLENR, 75},
{758*OVERSAMPLENR, 70},
{793*OVERSAMPLENR, 65},
{822*OVERSAMPLENR, 60},
{841*OVERSAMPLENR, 55},
{875*OVERSAMPLENR, 50},
{899*OVERSAMPLENR, 45},
{926*OVERSAMPLENR, 40},
{946*OVERSAMPLENR, 35},
{962*OVERSAMPLENR, 30},
{977*OVERSAMPLENR, 25},
{987*OVERSAMPLENR, 20},
{995*OVERSAMPLENR, 15},
{1001*OVERSAMPLENR, 10},
{1010*OVERSAMPLENR, 0},
{1023*OVERSAMPLENR, -40},
};
#endif
// Pt1000 and Pt100 handling
//
// Rt=R0*(1+a*T+b*T*T) [for T>0]
// a=3.9083E-3, b=-5.775E-7
#define PtA 3.9083E-3
#define PtB -5.775E-7
#define PtC -4.183E-12
#define PtRt(T,R0) ((R0)*(1.0+(PtA)*(T)+(PtB)*(T)*(T)))
#define PtRtNew(T,R0) ((R0)*(1.0+(PtA)*(T)+(PtB)*(T)*(T) + (T-100)*PtC*(T)*(T)*(T)))
#define PtAdVal(T,R0,Rup) (short)(1024/(Rup/PtRt(T,R0)+1))
#define PtLine(T,R0,Rup) { PtAdVal(T,R0,Rup)*OVERSAMPLENR, T },
#if (THERMISTORHEATER_0 == 110) || (THERMISTORHEATER_1 == 110) || (THERMISTORHEATER_2 == 110) || (THERMISTORBED == 110) // Pt100 with 1k0 pullup
const short temptable_110[][2] PROGMEM = {
// only few values are needed as the curve is very flat
PtLine(0,100,1000)
PtLine(50,100,1000)
PtLine(100,100,1000)
PtLine(150,100,1000)
PtLine(200,100,1000)
PtLine(250,100,1000)
PtLine(300,100,1000)
};
#endif
#if (THERMISTORHEATER_0 == 147) || (THERMISTORHEATER_1 == 147) || (THERMISTORHEATER_2 == 147) || (THERMISTORBED == 147) // Pt100 with 4k7 pullup
const short temptable_147[][2] PROGMEM = {
// only few values are needed as the curve is very flat
PtLine(0,100,4700)
PtLine(50,100,4700)
PtLine(100,100,4700)
PtLine(150,100,4700)
PtLine(200,100,4700)
PtLine(250,100,4700)
PtLine(300,100,4700)
};
#endif
// E3D Pt100 with 4k7 MiniRambo pullup, no Amp on the MiniRambo v1.3a
#if (THERMISTORHEATER_0 == 148) || (THERMISTORHEATER_1 == 148) || (THERMISTORHEATER_2 == 148) || (THERMISTORBED == 148)
const short temptable_148[][2] PROGMEM = {
// These values have been calculated and tested over many days. See https://docs.google.com/spreadsheets/d/1MJXa6feEe0mGVCT2TrBwLxVOMoLDkJlvfQ4JXhAdV_E
// Values that are missing from the 5C gap are missing due to resolution limits.
{19.00000 * OVERSAMPLENR, 0},
{19.25000 * OVERSAMPLENR, 5},
{19.50000 * OVERSAMPLENR, 10},
{19.87500 * OVERSAMPLENR, 15},
{20.25000 * OVERSAMPLENR, 20},
{21.00000 * OVERSAMPLENR, 25},
{21.75000 * OVERSAMPLENR, 35},
{22.00000 * OVERSAMPLENR, 40},
{23.00000 * OVERSAMPLENR, 50}, // 55C is more commonly used.
{23.75000 * OVERSAMPLENR, 60},
{24.00000 * OVERSAMPLENR, 65},
{24.06250 * OVERSAMPLENR, 70},
{25.00000 * OVERSAMPLENR, 75},
{25.50000 * OVERSAMPLENR, 85},
{26.00000 * OVERSAMPLENR, 90},
{26.93750 * OVERSAMPLENR,100},
{27.00000 * OVERSAMPLENR,105},
{27.37500 * OVERSAMPLENR,110},
{28.00000 * OVERSAMPLENR,115},
{29.00000 * OVERSAMPLENR,125},
{29.25000 * OVERSAMPLENR,135},
{30.00000 * OVERSAMPLENR,140},
{35.50000 * OVERSAMPLENR,150},
{31.00000 * OVERSAMPLENR,155},
{32.00000 * OVERSAMPLENR,165},
{32.18750 * OVERSAMPLENR,175},
{33.00000 * OVERSAMPLENR,180},
{33.62500 * OVERSAMPLENR,190},
{34.00000 * OVERSAMPLENR,195},
{35.00000 * OVERSAMPLENR,205},
{35.50000 * OVERSAMPLENR,215},
{36.00000 * OVERSAMPLENR,220},
{36.75000 * OVERSAMPLENR,230},
{37.00000 * OVERSAMPLENR,235},
{37.75000 * OVERSAMPLENR,245},
{38.00000 * OVERSAMPLENR,250},
{38.12500 * OVERSAMPLENR,255},
{39.00000 * OVERSAMPLENR,260},
{40.00000 * OVERSAMPLENR,275},
{40.25000 * OVERSAMPLENR,285},
{41.00000 * OVERSAMPLENR,290},
{41.25000 * OVERSAMPLENR,300},
{42.00000 * OVERSAMPLENR,305},
{43.00000 * OVERSAMPLENR,315},
{43.25000 * OVERSAMPLENR,325},
{44.00000 * OVERSAMPLENR,330},
{44.18750 * OVERSAMPLENR,340},
{45.00000 * OVERSAMPLENR,345},
{45.25000 * OVERSAMPLENR,355},
{46.00000 * OVERSAMPLENR,360},
{46.62500 * OVERSAMPLENR,370},
{47.00000 * OVERSAMPLENR,375},
{47.25000 * OVERSAMPLENR,385},
{48.00000 * OVERSAMPLENR,390},
{48.75000 * OVERSAMPLENR,400},
{49.00000 * OVERSAMPLENR,405},
};
#endif
#if (THERMISTORHEATER_0 == 247) || (THERMISTORHEATER_1 == 247) || (THERMISTORHEATER_2 == 247) || (THERMISTORBED == 247) // Pt100 with 4k7 MiniRambo pullup & PT100 Amplifier
const short temptable_247[][2] PROGMEM = {
// Calculated from Bob-the-Kuhn's PT100 calculator listed in https://github.com/MarlinFirmware/Marlin/issues/5543
// and the table provided by E3D at http://wiki.e3d-online.com/wiki/E3D_PT100_Amplifier_Documentation#Output_Characteristics.
{ 0 * OVERSAMPLENR, 0},
{241 * OVERSAMPLENR, 1},
{249 * OVERSAMPLENR, 10},
{259 * OVERSAMPLENR, 20},
{267 * OVERSAMPLENR, 30},
{275 * OVERSAMPLENR, 40},
{283 * OVERSAMPLENR, 50},
{291 * OVERSAMPLENR, 60},
{299 * OVERSAMPLENR, 70},
{307 * OVERSAMPLENR, 80},
{315 * OVERSAMPLENR, 90},
{323 * OVERSAMPLENR, 100},
{331 * OVERSAMPLENR, 110},
{340 * OVERSAMPLENR, 120},
{348 * OVERSAMPLENR, 130},
{354 * OVERSAMPLENR, 140},
{362 * OVERSAMPLENR, 150},
{370 * OVERSAMPLENR, 160},
{378 * OVERSAMPLENR, 170},
{386 * OVERSAMPLENR, 180},
{394 * OVERSAMPLENR, 190},
{402 * OVERSAMPLENR, 200},
{410 * OVERSAMPLENR, 210},
{418 * OVERSAMPLENR, 220},
{426 * OVERSAMPLENR, 230},
{432 * OVERSAMPLENR, 240},
{440 * OVERSAMPLENR, 250},
{448 * OVERSAMPLENR, 260},
{454 * OVERSAMPLENR, 270},
{462 * OVERSAMPLENR, 280},
{469 * OVERSAMPLENR, 290},
{475 * OVERSAMPLENR, 300},
{483 * OVERSAMPLENR, 310},
{491 * OVERSAMPLENR, 320},
{499 * OVERSAMPLENR, 330},
{505 * OVERSAMPLENR, 340},
{513 * OVERSAMPLENR, 350},
{519 * OVERSAMPLENR, 360},
{527 * OVERSAMPLENR, 370},
{533 * OVERSAMPLENR, 380},
{541 * OVERSAMPLENR, 390},
{549 * OVERSAMPLENR, 400},
{616 * OVERSAMPLENR, 500},
{682 * OVERSAMPLENR, 600},
{741 * OVERSAMPLENR, 700},
{801 * OVERSAMPLENR, 800},
{856 * OVERSAMPLENR, 900},
{910 * OVERSAMPLENR, 1000},
{960 * OVERSAMPLENR, 1100},
};
#endif
#if (THERMISTORHEATER_0 == 1010) || (THERMISTORHEATER_1 == 1010) || (THERMISTORHEATER_2 == 1010) || (THERMISTORBED == 1010) // Pt1000 with 1k0 pullup
const short temptable_1010[][2] PROGMEM = {
PtLine(0,1000,1000)
PtLine(25,1000,1000)
PtLine(50,1000,1000)
PtLine(75,1000,1000)
PtLine(100,1000,1000)
PtLine(125,1000,1000)
PtLine(150,1000,1000)
PtLine(175,1000,1000)
PtLine(200,1000,1000)
PtLine(225,1000,1000)
PtLine(250,1000,1000)
PtLine(275,1000,1000)
PtLine(300,1000,1000)
};
#endif
#if (THERMISTORHEATER_0 == 1047) || (THERMISTORHEATER_1 == 1047) || (THERMISTORHEATER_2 == 1047) || (THERMISTORBED == 1047) // Pt1000 with 4k7 pullup
const short temptable_1047[][2] PROGMEM = {
// only few values are needed as the curve is very flat
PtLine(0,1000,4700)
PtLine(50,1000,4700)
PtLine(100,1000,4700)
PtLine(150,1000,4700)
PtLine(200,1000,4700)
PtLine(250,1000,4700)
PtLine(300,1000,4700)
};
#endif
#if (THERMISTORAMBIENT == 2000) //100k thermistor NTCG104LH104JT1
# define AMBIENT_RAW_HI_TEMP 0
# define AMBIENT_RAW_LO_TEMP 16383
const short temptable_2000[][2] PROGMEM = {
// Source: https://product.tdk.com/info/en/catalog/datasheets/503021/tpd_ntc-thermistor_ntcg_en.pdf
// Calculated using 4.7kohm pullup, voltage divider math, and manufacturer provided temp/resistance
/*{305*OVERSAMPLENR, 125},
{338*OVERSAMPLENR, 120},
{374*OVERSAMPLENR, 115},
{412*OVERSAMPLENR, 110},
{452*OVERSAMPLENR, 105},
{494*OVERSAMPLENR, 100},
{536*OVERSAMPLENR, 95},
{580*OVERSAMPLENR, 90},
{623*OVERSAMPLENR, 85},
{665*OVERSAMPLENR, 80},
{706*OVERSAMPLENR, 75},
{744*OVERSAMPLENR, 70},
{780*OVERSAMPLENR, 65},
{813*OVERSAMPLENR, 60},
{843*OVERSAMPLENR, 55},
{869*OVERSAMPLENR, 50},
{892*OVERSAMPLENR, 45},
{912*OVERSAMPLENR, 40},
{929*OVERSAMPLENR, 35},
{943*OVERSAMPLENR, 30},
{955*OVERSAMPLENR, 25},
{965*OVERSAMPLENR, 20},
{973*OVERSAMPLENR, 15},
{979*OVERSAMPLENR, 10},
{984*OVERSAMPLENR, 5},
{988*OVERSAMPLENR, 0},
{991*OVERSAMPLENR, -5},
{993*OVERSAMPLENR, -10},
{995*OVERSAMPLENR, -15},
{996*OVERSAMPLENR, -20},
{997*OVERSAMPLENR, -25},
{998*OVERSAMPLENR, -30},
{999*OVERSAMPLENR, -35},
{999*OVERSAMPLENR, -40},*/
{313*OVERSAMPLENR,125},
{347*OVERSAMPLENR,120},
{383*OVERSAMPLENR,115},
{422*OVERSAMPLENR,110},
{463*OVERSAMPLENR,105},
{506*OVERSAMPLENR,100},
{549*OVERSAMPLENR,95},
{594*OVERSAMPLENR,90},
{638*OVERSAMPLENR,85},
{681*OVERSAMPLENR,80},
{722*OVERSAMPLENR,75},
{762*OVERSAMPLENR,70},
{799*OVERSAMPLENR,65},
{833*OVERSAMPLENR,60},
{863*OVERSAMPLENR,55},
{890*OVERSAMPLENR,50},
{914*OVERSAMPLENR,45},
{934*OVERSAMPLENR,40},
{951*OVERSAMPLENR,35},
{966*OVERSAMPLENR,30},
{978*OVERSAMPLENR,25},
{988*OVERSAMPLENR,20},
{996*OVERSAMPLENR,15},
{1002*OVERSAMPLENR,10},
{1007*OVERSAMPLENR,5},
{1012*OVERSAMPLENR,0},
{1015*OVERSAMPLENR,-5},
{1017*OVERSAMPLENR,-10},
{1019*OVERSAMPLENR,-15},
{1020*OVERSAMPLENR,-20},
{1021*OVERSAMPLENR,-25},
{1022*OVERSAMPLENR,-30},
{1023*OVERSAMPLENR,-35},
{1023*OVERSAMPLENR,-40},
};
#endif
#define _TT_NAME(_N) temptable_ ## _N
#define TT_NAME(_N) _TT_NAME(_N)
#ifdef THERMISTORHEATER_0
# define HEATER_0_TEMPTABLE TT_NAME(THERMISTORHEATER_0)
# define HEATER_0_TEMPTABLE_LEN (sizeof(HEATER_0_TEMPTABLE)/sizeof(*HEATER_0_TEMPTABLE))
#else
# ifdef HEATER_0_USES_THERMISTOR
# error No heater 0 thermistor table specified
# else // HEATER_0_USES_THERMISTOR
# define HEATER_0_TEMPTABLE NULL
# define HEATER_0_TEMPTABLE_LEN 0
# endif // HEATER_0_USES_THERMISTOR
#endif
//Set the high and low raw values for the heater, this indicates which raw value is a high or low temperature
#ifndef HEATER_0_RAW_HI_TEMP
# ifdef HEATER_0_USES_THERMISTOR //In case of a thermistor the highest temperature results in the lowest ADC value
# define HEATER_0_RAW_HI_TEMP 0
# define HEATER_0_RAW_LO_TEMP 16383
# else //In case of an thermocouple the highest temperature results in the highest ADC value
# define HEATER_0_RAW_HI_TEMP 16383
# define HEATER_0_RAW_LO_TEMP 0
# endif
#endif
#ifdef THERMISTORHEATER_1
# define HEATER_1_TEMPTABLE TT_NAME(THERMISTORHEATER_1)
# define HEATER_1_TEMPTABLE_LEN (sizeof(HEATER_1_TEMPTABLE)/sizeof(*HEATER_1_TEMPTABLE))
#else
# ifdef HEATER_1_USES_THERMISTOR
# error No heater 1 thermistor table specified
# else // HEATER_1_USES_THERMISTOR
# define HEATER_1_TEMPTABLE NULL
# define HEATER_1_TEMPTABLE_LEN 0
# endif // HEATER_1_USES_THERMISTOR
#endif
//Set the high and low raw values for the heater, this indicates which raw value is a high or low temperature
#ifndef HEATER_1_RAW_HI_TEMP
# ifdef HEATER_1_USES_THERMISTOR //In case of a thermistor the highest temperature results in the lowest ADC value
# define HEATER_1_RAW_HI_TEMP 0
# define HEATER_1_RAW_LO_TEMP 16383
# else //In case of an thermocouple the highest temperature results in the highest ADC value
# define HEATER_1_RAW_HI_TEMP 16383
# define HEATER_1_RAW_LO_TEMP 0
# endif
#endif
#ifdef THERMISTORHEATER_2
# define HEATER_2_TEMPTABLE TT_NAME(THERMISTORHEATER_2)
# define HEATER_2_TEMPTABLE_LEN (sizeof(HEATER_2_TEMPTABLE)/sizeof(*HEATER_2_TEMPTABLE))
#else
# ifdef HEATER_2_USES_THERMISTOR
# error No heater 2 thermistor table specified
# else // HEATER_2_USES_THERMISTOR
# define HEATER_2_TEMPTABLE NULL
# define HEATER_2_TEMPTABLE_LEN 0
# endif // HEATER_2_USES_THERMISTOR
#endif
//Set the high and low raw values for the heater, this indicates which raw value is a high or low temperature
#ifndef HEATER_2_RAW_HI_TEMP
# ifdef HEATER_2_USES_THERMISTOR //In case of a thermistor the highest temperature results in the lowest ADC value
# define HEATER_2_RAW_HI_TEMP 0
# define HEATER_2_RAW_LO_TEMP 16383
# else //In case of an thermocouple the highest temperature results in the highest ADC value
# define HEATER_2_RAW_HI_TEMP 16383
# define HEATER_2_RAW_LO_TEMP 0
# endif
#endif
#ifdef THERMISTORBED
# define BEDTEMPTABLE TT_NAME(THERMISTORBED)
# define BEDTEMPTABLE_LEN (sizeof(BEDTEMPTABLE)/sizeof(*BEDTEMPTABLE))
#else
# ifdef BED_USES_THERMISTOR
# error No bed thermistor table specified
# endif // BED_USES_THERMISTOR
#endif
#ifdef THERMISTORAMBIENT
# define AMBIENTTEMPTABLE TT_NAME(THERMISTORAMBIENT)
# define AMBIENTTEMPTABLE_LEN (sizeof(AMBIENTTEMPTABLE)/sizeof(*AMBIENTTEMPTABLE))
#endif
//Set the high and low raw values for the heater, this indicates which raw value is a high or low temperature
#ifndef HEATER_BED_RAW_HI_TEMP
# ifdef BED_USES_THERMISTOR //In case of a thermistor the highest temperature results in the lowest ADC value
# define HEATER_BED_RAW_HI_TEMP 0
# define HEATER_BED_RAW_LO_TEMP 16383
# else //In case of an thermocouple the highest temperature results in the highest ADC value
# define HEATER_BED_RAW_HI_TEMP 16383
# define HEATER_BED_RAW_LO_TEMP 0
# endif
#endif
#endif //THERMISTORTABLES_H_
Reference in New Issue View Git Blame Copy Permalink