505 lines
15 KiB
C
Executable File
505 lines
15 KiB
C
Executable File
// Tonokip RepRap firmware rewrite based off of Hydra-mmm firmware.
|
|
// License: GPL
|
|
|
|
#ifndef MARLIN_H
|
|
#define MARLIN_H
|
|
|
|
#include "macros.h"
|
|
|
|
#include <math.h>
|
|
#include <stdio.h>
|
|
#include <stdlib.h>
|
|
#include <string.h>
|
|
#include <inttypes.h>
|
|
|
|
#include <util/delay.h>
|
|
#include <avr/pgmspace.h>
|
|
#include <avr/eeprom.h>
|
|
#include <avr/interrupt.h>
|
|
#include "system_timer.h"
|
|
#include "fastio.h"
|
|
#include "Configuration.h"
|
|
#include "pins.h"
|
|
#include "Timer.h"
|
|
extern uint8_t mbl_z_probe_nr;
|
|
|
|
#ifndef AT90USB
|
|
#define HardwareSerial_h // trick to disable the standard HWserial
|
|
#endif
|
|
|
|
#if (ARDUINO >= 100)
|
|
# include "Arduino.h"
|
|
#else
|
|
# include "WProgram.h"
|
|
#endif
|
|
|
|
// Arduino < 1.0.0 does not define this, so we need to do it ourselves
|
|
#ifndef analogInputToDigitalPin
|
|
# define analogInputToDigitalPin(p) ((p) + A0)
|
|
#endif
|
|
|
|
#ifdef AT90USB
|
|
#include "HardwareSerial.h"
|
|
#endif
|
|
|
|
#include "MarlinSerial.h"
|
|
|
|
#ifndef cbi
|
|
#define cbi(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit))
|
|
#endif
|
|
#ifndef sbi
|
|
#define sbi(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit))
|
|
#endif
|
|
|
|
//#include "WString.h"
|
|
|
|
#ifdef AT90USB
|
|
#ifdef BTENABLED
|
|
#define MYSERIAL bt
|
|
#else
|
|
#define MYSERIAL Serial
|
|
#endif // BTENABLED
|
|
#else
|
|
#define MYSERIAL MSerial
|
|
#endif
|
|
|
|
#include "lcd.h"
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
extern FILE _uartout;
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
#define uartout (&_uartout)
|
|
|
|
#define SERIAL_PROTOCOL(x) (MYSERIAL.print(x))
|
|
#define SERIAL_PROTOCOL_F(x,y) (MYSERIAL.print(x,y))
|
|
#define SERIAL_PROTOCOLPGM(x) (serialprintPGM(PSTR(x)))
|
|
#define SERIAL_PROTOCOLRPGM(x) (serialprintPGM((x)))
|
|
#define SERIAL_PROTOCOLLN(x) (MYSERIAL.println(x)/*,MYSERIAL.write('\n')*/)
|
|
#define SERIAL_PROTOCOLLNPGM(x) (serialprintPGM(PSTR(x)),MYSERIAL.println()/*write('\n')*/)
|
|
#define SERIAL_PROTOCOLLNRPGM(x) (serialprintPGM((x)),MYSERIAL.println()/*write('\n')*/)
|
|
|
|
|
|
extern const char errormagic[] PROGMEM;
|
|
extern const char echomagic[] PROGMEM;
|
|
|
|
#define SERIAL_ERROR_START (serialprintPGM(errormagic))
|
|
#define SERIAL_ERROR(x) SERIAL_PROTOCOL(x)
|
|
#define SERIAL_ERRORPGM(x) SERIAL_PROTOCOLPGM(x)
|
|
#define SERIAL_ERRORRPGM(x) SERIAL_PROTOCOLRPGM(x)
|
|
#define SERIAL_ERRORLN(x) SERIAL_PROTOCOLLN(x)
|
|
#define SERIAL_ERRORLNPGM(x) SERIAL_PROTOCOLLNPGM(x)
|
|
#define SERIAL_ERRORLNRPGM(x) SERIAL_PROTOCOLLNRPGM(x)
|
|
|
|
#define SERIAL_ECHO_START (serialprintPGM(echomagic))
|
|
#define SERIAL_ECHO(x) SERIAL_PROTOCOL(x)
|
|
#define SERIAL_ECHOPGM(x) SERIAL_PROTOCOLPGM(x)
|
|
#define SERIAL_ECHORPGM(x) SERIAL_PROTOCOLRPGM(x)
|
|
#define SERIAL_ECHOLN(x) SERIAL_PROTOCOLLN(x)
|
|
#define SERIAL_ECHOLNPGM(x) SERIAL_PROTOCOLLNPGM(x)
|
|
#define SERIAL_ECHOLNRPGM(x) SERIAL_PROTOCOLLNRPGM(x)
|
|
|
|
#define SERIAL_ECHOPAIR(name,value) (serial_echopair_P(PSTR(name),(value)))
|
|
|
|
void serial_echopair_P(const char *s_P, float v);
|
|
void serial_echopair_P(const char *s_P, double v);
|
|
void serial_echopair_P(const char *s_P, unsigned long v);
|
|
|
|
|
|
//Things to write to serial from Program memory. Saves 400 to 2k of RAM.
|
|
// Making this FORCE_INLINE is not a good idea when running out of FLASH
|
|
// I'd rather skip a few CPU ticks than 5.5KB (!!) of FLASH
|
|
void serialprintPGM(const char *str);
|
|
|
|
bool is_buffer_empty();
|
|
void process_commands();
|
|
void ramming();
|
|
|
|
void manage_inactivity(bool ignore_stepper_queue=false);
|
|
|
|
#if defined(X_ENABLE_PIN) && X_ENABLE_PIN > -1
|
|
#define enable_x() WRITE(X_ENABLE_PIN, X_ENABLE_ON)
|
|
#define disable_x() { WRITE(X_ENABLE_PIN,!X_ENABLE_ON); axis_known_position[X_AXIS] = false; }
|
|
#else
|
|
#define enable_x() ;
|
|
#define disable_x() ;
|
|
#endif
|
|
|
|
#if defined(Y_ENABLE_PIN) && Y_ENABLE_PIN > -1
|
|
#ifdef Y_DUAL_STEPPER_DRIVERS
|
|
#define enable_y() { WRITE(Y_ENABLE_PIN, Y_ENABLE_ON); WRITE(Y2_ENABLE_PIN, Y_ENABLE_ON); }
|
|
#define disable_y() { WRITE(Y_ENABLE_PIN,!Y_ENABLE_ON); WRITE(Y2_ENABLE_PIN, !Y_ENABLE_ON); axis_known_position[Y_AXIS] = false; }
|
|
#else
|
|
#define enable_y() WRITE(Y_ENABLE_PIN, Y_ENABLE_ON)
|
|
#define disable_y() { WRITE(Y_ENABLE_PIN,!Y_ENABLE_ON); axis_known_position[Y_AXIS] = false; }
|
|
#endif
|
|
#else
|
|
#define enable_y() ;
|
|
#define disable_y() ;
|
|
#endif
|
|
|
|
#if defined(Z_ENABLE_PIN) && Z_ENABLE_PIN > -1
|
|
#if defined(Z_AXIS_ALWAYS_ON)
|
|
#ifdef Z_DUAL_STEPPER_DRIVERS
|
|
#define poweron_z() { WRITE(Z_ENABLE_PIN, Z_ENABLE_ON); WRITE(Z2_ENABLE_PIN, Z_ENABLE_ON); }
|
|
#define poweroff_z() { WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON); WRITE(Z2_ENABLE_PIN,!Z_ENABLE_ON); axis_known_position[Z_AXIS] = false; }
|
|
#else
|
|
#define poweron_z() WRITE(Z_ENABLE_PIN, Z_ENABLE_ON)
|
|
#define poweroff_z() {}
|
|
#endif
|
|
#else
|
|
#ifdef Z_DUAL_STEPPER_DRIVERS
|
|
#define poweron_z() { WRITE(Z_ENABLE_PIN, Z_ENABLE_ON); WRITE(Z2_ENABLE_PIN, Z_ENABLE_ON); }
|
|
#define poweroff_z() { WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON); WRITE(Z2_ENABLE_PIN,!Z_ENABLE_ON); axis_known_position[Z_AXIS] = false; }
|
|
#else
|
|
#define poweron_z() WRITE(Z_ENABLE_PIN, Z_ENABLE_ON)
|
|
#define poweroff_z() { WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON); axis_known_position[Z_AXIS] = false; }
|
|
#endif
|
|
#endif
|
|
#else
|
|
#define poweron_z() {}
|
|
#define poweroff_z() {}
|
|
#endif
|
|
|
|
#ifndef PSU_Delta
|
|
#define enable_z() poweron_z()
|
|
#define disable_z() poweroff_z()
|
|
#else
|
|
void init_force_z();
|
|
void check_force_z();
|
|
void enable_force_z();
|
|
void disable_force_z();
|
|
#define enable_z() enable_force_z()
|
|
#define disable_z() disable_force_z()
|
|
#endif // PSU_Delta
|
|
|
|
|
|
//#if defined(Z_ENABLE_PIN) && Z_ENABLE_PIN > -1
|
|
//#ifdef Z_DUAL_STEPPER_DRIVERS
|
|
//#define enable_z() { WRITE(Z_ENABLE_PIN, Z_ENABLE_ON); WRITE(Z2_ENABLE_PIN, Z_ENABLE_ON); }
|
|
//#define disable_z() { WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON); WRITE(Z2_ENABLE_PIN,!Z_ENABLE_ON); axis_known_position[Z_AXIS] = false; }
|
|
//#else
|
|
//#define enable_z() WRITE(Z_ENABLE_PIN, Z_ENABLE_ON)
|
|
//#define disable_z() { WRITE(Z_ENABLE_PIN,!Z_ENABLE_ON); axis_known_position[Z_AXIS] = false; }
|
|
//#endif
|
|
//#else
|
|
//#define enable_z() ;
|
|
//#define disable_z() ;
|
|
//#endif
|
|
|
|
|
|
#if defined(E0_ENABLE_PIN) && (E0_ENABLE_PIN > -1)
|
|
#define enable_e0() WRITE(E0_ENABLE_PIN, E_ENABLE_ON)
|
|
#define disable_e0() WRITE(E0_ENABLE_PIN,!E_ENABLE_ON)
|
|
#else
|
|
#define enable_e0() /* nothing */
|
|
#define disable_e0() /* nothing */
|
|
#endif
|
|
|
|
#if (EXTRUDERS > 1) && defined(E1_ENABLE_PIN) && (E1_ENABLE_PIN > -1)
|
|
#define enable_e1() WRITE(E1_ENABLE_PIN, E_ENABLE_ON)
|
|
#define disable_e1() WRITE(E1_ENABLE_PIN,!E_ENABLE_ON)
|
|
#else
|
|
#define enable_e1() /* nothing */
|
|
#define disable_e1() /* nothing */
|
|
#endif
|
|
|
|
#if (EXTRUDERS > 2) && defined(E2_ENABLE_PIN) && (E2_ENABLE_PIN > -1)
|
|
#define enable_e2() WRITE(E2_ENABLE_PIN, E_ENABLE_ON)
|
|
#define disable_e2() WRITE(E2_ENABLE_PIN,!E_ENABLE_ON)
|
|
#else
|
|
#define enable_e2() /* nothing */
|
|
#define disable_e2() /* nothing */
|
|
#endif
|
|
|
|
|
|
#define FARM_FILAMENT_COLOR_NONE 99;
|
|
|
|
|
|
enum AxisEnum {X_AXIS=0, Y_AXIS=1, Z_AXIS=2, E_AXIS=3, X_HEAD=4, Y_HEAD=5};
|
|
#define X_AXIS_MASK 1
|
|
#define Y_AXIS_MASK 2
|
|
#define Z_AXIS_MASK 4
|
|
#define E_AXIS_MASK 8
|
|
#define X_HEAD_MASK 16
|
|
#define Y_HEAD_MASK 32
|
|
|
|
|
|
void FlushSerialRequestResend();
|
|
void ClearToSend();
|
|
void update_currents();
|
|
|
|
void get_coordinates();
|
|
void prepare_move();
|
|
void kill(const char *full_screen_message = NULL, unsigned char id = 0);
|
|
void Stop();
|
|
bool IsStopped();
|
|
void finishAndDisableSteppers();
|
|
|
|
//put an ASCII command at the end of the current buffer, read from flash
|
|
#define enquecommand_P(cmd) enquecommand(cmd, true)
|
|
|
|
//put an ASCII command at the begin of the current buffer, read from flash
|
|
#define enquecommand_front_P(cmd) enquecommand_front(cmd, true)
|
|
|
|
void prepare_arc_move(char isclockwise);
|
|
void clamp_to_software_endstops(float target[3]);
|
|
void refresh_cmd_timeout(void);
|
|
|
|
// Timer counter, incremented by the 1ms Arduino timer.
|
|
// The standard Arduino timer() function returns this value atomically
|
|
// by disabling / enabling interrupts. This is costly, if the interrupts are known
|
|
// to be disabled.
|
|
#ifdef SYSTEM_TIMER_2
|
|
extern volatile unsigned long timer2_millis;
|
|
#else //SYSTEM_TIMER_2
|
|
extern volatile unsigned long timer0_millis;
|
|
#endif //SYSTEM_TIMER_2
|
|
|
|
// An unsynchronized equivalent to a standard Arduino _millis() function.
|
|
// To be used inside an interrupt routine.
|
|
|
|
FORCE_INLINE unsigned long millis_nc() {
|
|
#ifdef SYSTEM_TIMER_2
|
|
return timer2_millis;
|
|
#else //SYSTEM_TIMER_2
|
|
return timer0_millis;
|
|
#endif //SYSTEM_TIMER_2
|
|
}
|
|
|
|
#ifdef FAST_PWM_FAN
|
|
void setPwmFrequency(uint8_t pin, int val);
|
|
#endif
|
|
|
|
extern bool fans_check_enabled;
|
|
extern float homing_feedrate[];
|
|
extern uint8_t axis_relative_modes;
|
|
extern float feedrate;
|
|
extern int feedmultiply;
|
|
extern int extrudemultiply; // Sets extrude multiply factor (in percent) for all extruders
|
|
extern int extruder_multiply[EXTRUDERS]; // sets extrude multiply factor (in percent) for each extruder individually
|
|
extern float extruder_multiplier[EXTRUDERS]; // reciprocal of cross-sectional area of filament (in square millimeters), stored this way to reduce computational burden in planner
|
|
extern float current_position[NUM_AXIS] ;
|
|
extern float destination[NUM_AXIS] ;
|
|
extern float min_pos[3];
|
|
extern float max_pos[3];
|
|
extern bool axis_known_position[3];
|
|
extern int fanSpeed;
|
|
extern uint8_t newFanSpeed;
|
|
extern int8_t lcd_change_fil_state;
|
|
extern float default_retraction;
|
|
|
|
#ifdef TMC2130
|
|
void homeaxis(uint8_t axis, uint8_t cnt = 1, uint8_t* pstep = 0);
|
|
#else
|
|
void homeaxis(uint8_t axis, uint8_t cnt = 1);
|
|
#endif //TMC2130
|
|
|
|
|
|
#ifdef FAN_SOFT_PWM
|
|
extern unsigned char fanSpeedSoftPwm;
|
|
#endif
|
|
|
|
#ifdef FWRETRACT
|
|
extern bool retracted[EXTRUDERS];
|
|
extern float retract_length_swap;
|
|
extern float retract_recover_length_swap;
|
|
#endif
|
|
|
|
|
|
extern uint8_t host_keepalive_interval;
|
|
|
|
extern unsigned long starttime;
|
|
extern unsigned long stoptime;
|
|
extern int bowden_length[4];
|
|
extern bool is_usb_printing;
|
|
extern bool homing_flag;
|
|
extern bool loading_flag;
|
|
extern unsigned int usb_printing_counter;
|
|
|
|
extern unsigned long kicktime;
|
|
|
|
extern unsigned long total_filament_used;
|
|
void save_statistics(unsigned long _total_filament_used, unsigned long _total_print_time);
|
|
extern unsigned int heating_status;
|
|
extern unsigned int status_number;
|
|
extern unsigned int heating_status_counter;
|
|
extern char snmm_filaments_used;
|
|
extern unsigned long PingTime;
|
|
extern unsigned long NcTime;
|
|
extern bool no_response;
|
|
extern uint8_t important_status;
|
|
extern uint8_t saved_filament_type;
|
|
|
|
extern bool fan_state[2];
|
|
extern int fan_edge_counter[2];
|
|
extern int fan_speed[2];
|
|
|
|
// Handling multiple extruders pins
|
|
extern uint8_t active_extruder;
|
|
|
|
//Long pause
|
|
extern unsigned long pause_time;
|
|
extern unsigned long start_pause_print;
|
|
extern unsigned long t_fan_rising_edge;
|
|
|
|
extern bool mesh_bed_leveling_flag;
|
|
extern bool mesh_bed_run_from_menu;
|
|
|
|
extern int8_t lcd_change_fil_state;
|
|
// save/restore printing
|
|
extern bool saved_printing;
|
|
extern uint8_t saved_printing_type;
|
|
#define PRINTING_TYPE_SD 0
|
|
#define PRINTING_TYPE_USB 1
|
|
#define PRINTING_TYPE_NONE 2
|
|
|
|
//save/restore printing in case that mmu is not responding
|
|
extern bool mmu_print_saved;
|
|
|
|
//estimated time to end of the print
|
|
extern uint8_t print_percent_done_normal;
|
|
extern uint8_t print_percent_done_silent;
|
|
extern uint16_t print_time_remaining_normal;
|
|
extern uint16_t print_time_remaining_silent;
|
|
extern uint16_t print_time_to_change_normal;
|
|
extern uint16_t print_time_to_change_silent;
|
|
|
|
#define PRINT_TIME_REMAINING_INIT 0xffff
|
|
|
|
extern uint16_t mcode_in_progress;
|
|
extern uint16_t gcode_in_progress;
|
|
|
|
extern LongTimer safetyTimer;
|
|
|
|
#define PRINT_PERCENT_DONE_INIT 0xff
|
|
#define PRINTER_ACTIVE (IS_SD_PRINTING || is_usb_printing || isPrintPaused || (custom_message_type == CustomMsg::TempCal) || saved_printing || (lcd_commands_type == LcdCommands::Layer1Cal) || mmu_print_saved || homing_flag || mesh_bed_leveling_flag)
|
|
|
|
//! Beware - mcode_in_progress is set as soon as the command gets really processed,
|
|
//! which is not the same as posting the M600 command into the command queue
|
|
//! There can be a considerable lag between posting M600 and its real processing which might result
|
|
//! in posting multiple M600's into the command queue
|
|
//! Instead, the fsensor uses another state variable :( , which is set to true, when the M600 command is enqued
|
|
//! and is reset to false when the fsensor returns into its filament runout finished handler
|
|
//! I'd normally change this macro, but who knows what would happen in the MMU :)
|
|
#define CHECK_FSENSOR ((IS_SD_PRINTING || is_usb_printing) && (mcode_in_progress != 600) && !saved_printing && e_active())
|
|
|
|
extern void calculate_extruder_multipliers();
|
|
|
|
// Similar to the default Arduino delay function,
|
|
// but it keeps the background tasks running.
|
|
extern void delay_keep_alive(unsigned int ms);
|
|
|
|
extern void check_babystep();
|
|
|
|
extern void long_pause();
|
|
extern void crashdet_stop_and_save_print();
|
|
|
|
#ifdef HEATBED_ANALYSIS
|
|
void d_setup();
|
|
float d_ReadData();
|
|
void bed_analysis(float x_dimension, float y_dimension, int x_points_num, int y_points_num, float shift_x, float shift_y);
|
|
void bed_check(float x_dimension, float y_dimension, int x_points_num, int y_points_num, float shift_x, float shift_y);
|
|
#endif //HEATBED_ANALYSIS
|
|
float temp_comp_interpolation(float temperature);
|
|
void show_fw_version_warnings();
|
|
uint8_t check_printer_version();
|
|
|
|
#ifdef PINDA_THERMISTOR
|
|
float temp_compensation_pinda_thermistor_offset(float temperature_pinda);
|
|
#endif //PINDA_THERMISTOR
|
|
|
|
void serialecho_temperatures();
|
|
bool check_commands();
|
|
|
|
void uvlo_();
|
|
void uvlo_tiny();
|
|
void recover_print(uint8_t automatic);
|
|
void setup_uvlo_interrupt();
|
|
|
|
#if defined(TACH_1) && TACH_1 >-1
|
|
void setup_fan_interrupt();
|
|
#endif
|
|
|
|
extern bool recover_machine_state_after_power_panic();
|
|
extern void restore_print_from_eeprom(bool mbl_was_active);
|
|
extern void position_menu();
|
|
|
|
extern void print_world_coordinates();
|
|
extern void print_physical_coordinates();
|
|
extern void print_mesh_bed_leveling_table();
|
|
|
|
extern void stop_and_save_print_to_ram(float z_move, float e_move);
|
|
extern void restore_print_from_ram_and_continue(float e_move);
|
|
extern void cancel_saved_printing();
|
|
|
|
|
|
//estimated time to end of the print
|
|
extern uint8_t calc_percent_done();
|
|
|
|
|
|
|
|
// States for managing Marlin and host communication
|
|
// Marlin sends messages if blocked or busy
|
|
/*enum MarlinBusyState {
|
|
NOT_BUSY, // Not in a handler
|
|
IN_HANDLER, // Processing a GCode
|
|
IN_PROCESS, // Known to be blocking command input (as in G29)
|
|
PAUSED_FOR_USER, // Blocking pending any input
|
|
PAUSED_FOR_INPUT // Blocking pending text input (concept)
|
|
};*/
|
|
|
|
#define NOT_BUSY 1
|
|
#define IN_HANDLER 2
|
|
#define IN_PROCESS 3
|
|
#define PAUSED_FOR_USER 4
|
|
#define PAUSED_FOR_INPUT 5
|
|
|
|
#define KEEPALIVE_STATE(n) do { busy_state = n;} while (0)
|
|
extern void host_keepalive();
|
|
//extern MarlinBusyState busy_state;
|
|
extern int8_t busy_state;
|
|
|
|
|
|
#ifdef TMC2130
|
|
|
|
#define FORCE_HIGH_POWER_START force_high_power_mode(true)
|
|
#define FORCE_HIGH_POWER_END force_high_power_mode(false)
|
|
|
|
void force_high_power_mode(bool start_high_power_section);
|
|
|
|
#endif //TMC2130
|
|
|
|
// G-codes
|
|
|
|
bool gcode_M45(bool onlyZ, int8_t verbosity_level);
|
|
void gcode_M114();
|
|
#if (defined(FANCHECK) && (((defined(TACH_0) && (TACH_0 >-1)) || (defined(TACH_1) && (TACH_1 > -1)))))
|
|
void gcode_M123();
|
|
#endif //FANCHECK and TACH_0 and TACH_1
|
|
void gcode_M701();
|
|
|
|
#define UVLO !(PINE & (1<<4))
|
|
|
|
void proc_commands();
|
|
|
|
|
|
void M600_load_filament();
|
|
void M600_load_filament_movements();
|
|
void M600_wait_for_user(float HotendTempBckp);
|
|
void M600_check_state(float nozzle_temp);
|
|
void load_filament_final_feed();
|
|
void marlin_wait_for_click();
|
|
void raise_z_above(float target, bool plan=true);
|
|
|
|
extern "C" void softReset();
|
|
void stack_error();
|
|
|
|
extern uint32_t IP_address;
|
|
|
|
#endif
|