Prusa-Firmware/Firmware/MarlinSerial.cpp

/*
  HardwareSerial.cpp - Hardware serial library for Wiring
  Copyright (c) 2006 Nicholas Zambetti.  All right reserved.

  This library is free software; you can redistribute it and/or
  modify it under the terms of the GNU Lesser General Public
  License as published by the Free Software Foundation; either
  version 2.1 of the License, or (at your option) any later version.

  This library is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
  Lesser General Public License for more details.

  You should have received a copy of the GNU Lesser General Public
  License along with this library; if not, write to the Free Software
  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
  
  Modified 23 November 2006 by David A. Mellis
  Modified 28 September 2010 by Mark Sproul
*/

#include "Marlin.h"
#include "MarlinSerial.h"

uint8_t selectedSerialPort = 0;

#ifndef AT90USB
// this next line disables the entire HardwareSerial.cpp, 
// this is so I can support Attiny series and any other chip without a UART
#if defined(UBRRH) || defined(UBRR0H) || defined(UBRR1H) || defined(UBRR2H) || defined(UBRR3H)

#ifdef HAS_UART
  ring_buffer rx_buffer  =  { { 0 }, 0, 0 };
#endif

FORCE_INLINE void store_char(unsigned char c)
{
  int i = (unsigned int)(rx_buffer.head + 1) % RX_BUFFER_SIZE;

  // if we should be storing the received character into the location
  // just before the tail (meaning that the head would advance to the
  // current location of the tail), we're about to overflow the buffer
  // and so we don't write the character or advance the head.
  if (i != rx_buffer.tail) {
    rx_buffer.buffer[rx_buffer.head] = c;
    rx_buffer.head = i;
  }
}


#if defined(M_USARTx_RX_vect)
// The serial line receive interrupt routine for a baud rate 115200
// ticks at maximum 11.76 kHz and blocks for 2.688 us at each tick.
// If the serial line is fully utilized, this corresponds to 3.16%
// loading of the CPU (the interrupt invocation overhead not taken into account).
// As the serial line is not fully utilized, the CPU load is likely around 1%.
ISR(M_USARTx_RX_vect)
{
	// Test for a framing error.
	if (M_UCSRxA & (1<<M_FEx))
	{
		// Characters received with the framing errors will be ignored.
		// Dummy register read (discard)
		(void)(*(char *)M_UDRx);
	}
	else
	{
		// Read the input register.
		unsigned char c = M_UDRx;
		if (selectedSerialPort == 0)
			store_char(c);
#ifdef DEBUG_DUMP_TO_2ND_SERIAL
		UDR1 = c;
#endif //DEBUG_DUMP_TO_2ND_SERIAL
	}
}
#ifndef SNMM
ISR(USART1_RX_vect)
{
	// Test for a framing error.
	if (UCSR1A & (1<<FE1))
	{
		// Characters received with the framing errors will be ignored.
		// Dummy register read (discard)
		(void)(*(char *)UDR1);
	}
	else
	{
		// Read the input register.
		unsigned char c = UDR1;
		if (selectedSerialPort == 1)
			store_char(c);
#ifdef DEBUG_DUMP_TO_2ND_SERIAL
		M_UDRx = c;
#endif //DEBUG_DUMP_TO_2ND_SERIAL
	}
}
#endif
#endif

// Public Methods //////////////////////////////////////////////////////////////

void MarlinSerial::begin(long baud)
{
  uint16_t baud_setting;
  bool useU2X = true;

#if F_CPU == 16000000UL && SERIAL_PORT == 0
  // hard-coded exception for compatibility with the bootloader shipped
  // with the Duemilanove and previous boards and the firmware on the 8U2
  // on the Uno and Mega 2560.
  if (baud == 57600) {
    useU2X = false;
  }
#endif
// set up the first (original serial port)
  if (useU2X) {
    M_UCSRxA = 1 << M_U2Xx;
    baud_setting = (F_CPU / 4 / baud - 1) / 2;
  } else {
    M_UCSRxA = 0;
    baud_setting = (F_CPU / 8 / baud - 1) / 2;
  }

  // assign the baud_setting, a.k.a. ubbr (USART Baud Rate Register)
  M_UBRRxH = baud_setting >> 8;
  M_UBRRxL = baud_setting;

  sbi(M_UCSRxB, M_RXENx);
  sbi(M_UCSRxB, M_TXENx);
  sbi(M_UCSRxB, M_RXCIEx);
  
#ifndef SNMM

  if (selectedSerialPort == 1) { //set up also the second serial port 
	  if (useU2X) {
		  UCSR1A = 1 << U2X1;
		  baud_setting = (F_CPU / 4 / baud - 1) / 2;
	  } else {
		  UCSR1A = 0;
		  baud_setting = (F_CPU / 8 / baud - 1) / 2;
	  }

	  // assign the baud_setting, a.k.a. ubbr (USART Baud Rate Register)
	  UBRR1H = baud_setting >> 8;
	  UBRR1L = baud_setting;
	  
	  sbi(UCSR1B, RXEN1);
	  sbi(UCSR1B, TXEN1);
	  sbi(UCSR1B, RXCIE1);	  
  }
#endif
}

void MarlinSerial::end()
{
  cbi(M_UCSRxB, M_RXENx);
  cbi(M_UCSRxB, M_TXENx);
  cbi(M_UCSRxB, M_RXCIEx);

#ifndef SNMM
  cbi(UCSR1B, RXEN1);
  cbi(UCSR1B, TXEN1);
  cbi(UCSR1B, RXCIE1);
#endif
}



int MarlinSerial::peek(void)
{
  if (rx_buffer.head == rx_buffer.tail) {
    return -1;
  } else {
    return rx_buffer.buffer[rx_buffer.tail];
  }
}

int MarlinSerial::read(void)
{
  // if the head isn't ahead of the tail, we don't have any characters
  if (rx_buffer.head == rx_buffer.tail) {
    return -1;
  } else {
    unsigned char c = rx_buffer.buffer[rx_buffer.tail];
    rx_buffer.tail = (unsigned int)(rx_buffer.tail + 1) % RX_BUFFER_SIZE;
    return c;
  }
}

void MarlinSerial::flush()
{
  // don't reverse this or there may be problems if the RX interrupt
  // occurs after reading the value of rx_buffer_head but before writing
  // the value to rx_buffer_tail; the previous value of rx_buffer_head
  // may be written to rx_buffer_tail, making it appear as if the buffer
  // were full, not empty.
  rx_buffer.head = rx_buffer.tail;
}




/// imports from print.h




void MarlinSerial::print(char c, int base)
{
  print((long) c, base);
}

void MarlinSerial::print(unsigned char b, int base)
{
  print((unsigned long) b, base);
}

void MarlinSerial::print(int n, int base)
{
  print((long) n, base);
}

void MarlinSerial::print(unsigned int n, int base)
{
  print((unsigned long) n, base);
}

void MarlinSerial::print(long n, int base)
{
  if (base == 0) {
    write(n);
  } else if (base == 10) {
    if (n < 0) {
      print('-');
      n = -n;
    }
    printNumber(n, 10);
  } else {
    printNumber(n, base);
  }
}

void MarlinSerial::print(unsigned long n, int base)
{
  if (base == 0) write(n);
  else printNumber(n, base);
}

void MarlinSerial::print(double n, int digits)
{
  printFloat(n, digits);
}

void MarlinSerial::println(void)
{
  // print('\r');
  print('\n');  
}

/*void MarlinSerial::println(const String &s)
{
  print(s);
  println();
}*/

void MarlinSerial::println(const char c[])
{
  print(c);
  println();
}

void MarlinSerial::println(char c, int base)
{
  print(c, base);
  println();
}

void MarlinSerial::println(unsigned char b, int base)
{
  print(b, base);
  println();
}

void MarlinSerial::println(int n, int base)
{
  print(n, base);
  println();
}

void MarlinSerial::println(unsigned int n, int base)
{
  print(n, base);
  println();
}

void MarlinSerial::println(long n, int base)
{
  print(n, base);
  println();
}

void MarlinSerial::println(unsigned long n, int base)
{
  print(n, base);
  println();
}

void MarlinSerial::println(double n, int digits)
{
  print(n, digits);
  println();
}

// Private Methods /////////////////////////////////////////////////////////////

void MarlinSerial::printNumber(unsigned long n, uint8_t base)
{
  unsigned char buf[8 * sizeof(long)]; // Assumes 8-bit chars. 
  unsigned long i = 0;

  if (n == 0) {
    print('0');
    return;
  } 

  while (n > 0) {
    buf[i++] = n % base;
    n /= base;
  }

  for (; i > 0; i--)
    print((char) (buf[i - 1] < 10 ?
      '0' + buf[i - 1] :
      'A' + buf[i - 1] - 10));
}

void MarlinSerial::printFloat(double number, uint8_t digits) 
{ 
  // Handle negative numbers
  if (number < 0.0)
  {
     print('-');
     number = -number;
  }

  // Round correctly so that print(1.999, 2) prints as "2.00"
  double rounding = 0.5;
  for (uint8_t i=0; i<digits; ++i)
    rounding /= 10.0;
  
  number += rounding;

  // Extract the integer part of the number and print it
  unsigned long int_part = (unsigned long)number;
  double remainder = number - (double)int_part;
  print(int_part);

  // Print the decimal point, but only if there are digits beyond
  if (digits > 0)
    print('.'); 

  // Extract digits from the remainder one at a time
  while (digits-- > 0)
  {
    remainder *= 10.0;
    int toPrint = int(remainder);
    print(toPrint);
    remainder -= toPrint; 
  } 
}
// Preinstantiate Objects //////////////////////////////////////////////////////


MarlinSerial MSerial;

#endif // whole file
#endif // !AT90USB

// For AT90USB targets use the UART for BT interfacing
#if defined(AT90USB) && defined (BTENABLED)
   HardwareSerial bt;
#endif