end_gcode=M400 ; wait for moves to finish\nM140 S40 ; start bed cooling\nM104 S0 ; disable hotend\nM107 ; disable fans\nG92 E1 ; set extruder to 1mm for retract on print end (LulzBot Cura had 5mm, might be a contributing factor to between print Aerostruder jamming)\nM117 Cooling please wait ; progress indicator message on LCD\nG1 X5 Y5 Z158 E0 F10000 ; move to cooling position\nG1 E1 ; re-prime extruder\nM190 R40 ; wait for bed to cool down to removal temp\nM77 ; Stop GLCD Timer\nG1 X145 F1000 ; move extruder out of the way\nG1 Y175 F1000 ; present finished print\nM140 S0; cool downs\nM84 ; disable steppers\nG90 ; absolute positioning\nM117 Print Complete. ; print complete message\n
extra_loading_move=-2
extruder_colour=""
extruder_offset=0x0
gcode_flavor=marlin
high_current_on_filament_swap=0
host_type=octoprint
inherits=
layer_gcode=
machine_max_acceleration_e=10000,5000
machine_max_acceleration_extruding=1500,1250
machine_max_acceleration_retracting=1500,1250
machine_max_acceleration_x=9000,1000
machine_max_acceleration_y=9000,1000
machine_max_acceleration_z=100,200
machine_max_feedrate_e=40,120
machine_max_feedrate_x=800,200
machine_max_feedrate_y=800,200
machine_max_feedrate_z=8,12
machine_max_jerk_e=2.5,2.5
machine_max_jerk_x=20,10
machine_max_jerk_y=20,10
machine_max_jerk_z=0.2,0.4
machine_min_extruding_rate=0,0
machine_min_travel_rate=0,0
max_layer_height=0
max_print_height=158
min_layer_height=0.07
nozzle_diameter=0.5
parking_pos_retraction=92
print_host=
printer_notes=LulzBot Mini w/ Aerostruder profile for Delaware Library System, Rt9 Library and Innovation Center.
printhost_apikey=
printhost_cafile=
remaining_times=0
retract_before_travel=2
retract_before_wipe=0%
retract_layer_change=1
retract_length=1
retract_length_toolchange=10
retract_lift=0
retract_lift_above=0
retract_lift_below=0
retract_restart_extra=0
retract_restart_extra_toolchange=0
retract_speed=40
serial_port=
serial_speed=250000
silent_mode=0
single_extruder_multi_material=0
start_gcode=;This G-Code has been generated specifically for the LulzBot Mini with Aerosturder\nM73 P0 ; clear GLCD progress bar\nM75 ; start GLCD timer\nG26 ; clear potential 'probe fail' condition\nM107 ; disable fans\nM420 S0 ; disable leveling matrix\nG90 ; absolute positioning\nM82 ; set extruder to absolute mode\nG92 E0 ; set extruder position to 0\nM140 S{first_layer_bed_temperature[0]} ; start bed heating up\nG28; home all axes\nG0 X0 Y187 Z156 F200 ; move away from endstops\nM109 R{first_layer_temperature[0] - 60} ; soften filament before retraction\n;G1 E-15 F75 ; retract filament (LulzBot Cura is apparently trying to cold pull, might be a contributing factor to hob gear filling with filament)\nM109 R{first_layer_temperature[0] - 60} ; wait for extruder to reach wiping temp\nG1 X45 Y173 F11520 ; move above wiper pad\nG1 Z0 F1200 ; push nozzle into wiper\nG1 X42 Y173 Z-.5 F4000 ; wiping\nG1 X52 Y171 Z-.5 F4000 ; wiping\nG1 X42 Y173 Z0 F4000 ; wiping\nG1 X52 Y171 F4000 ; wiping\nG1 X42 Y173 F4000 ; wiping\nG1 X52 Y171 F4000 ; wiping\nG1 X42 Y173 F4000 ; wiping\nG1 X52 Y171 F4000 ; wiping\nG1 X57 Y173 F4000 ; wiping\nG1 X77 Y171 F4000 ; wiping\nG1 X57 Y173 F4000 ; wiping\nG1 X77 Y171 F4000 ; wiping\nG1 X57 Y173 F4000 ; wiping\nG1 X87 Y171 F4000 ; wiping\nG1 X77 Y173 F4000 ; wiping\nG1 X97 Y171 F4000 ; wiping\nG1 X77 Y173 F4000 ; wiping\nG1 X97 Y171 F4000 ; wiping\nG1 X77 Y173 F4000 ; wiping\nG1 X97 Y171 F4000 ; wiping\nG1 X107 Y173 F4000 ; wiping\nG1 X97 Y171 F4000 ; wiping\nG1 X107 Y173 F4000 ; wiping\nG1 X97 Y171 F4000 ; wiping\nG1 X107 Y173 F4000 ; wiping\nG1 X112 Y171 Z-0.5 F1000 ; wiping\nG1 Z10 ; raise extruder\nG28 X0 Y0 ; home X and Y\nG0 X0 Y187 F200 ; move away from endstops\nM109 R{first_layer_temperature[0] - 60} ; wait for extruder to reach probe temp\nM204 S300 ; set probing acceleration\nG29 ; start auto-leveling sequence\nM420 S1 ; enable leveling matrix\nM425 Z ; use measured Z backlash for compensation\nM425 Z F0 ; turn off measured Z backlash compensation. (if activated in the quality settings, this command will automatically be ignored)\nM204 S2000 ; restore standard acceleration\nG28 X0 Y0 ; re-home to account for build variance of earlier mini builds\nG0 X0 Y187 F200 ; move away from endstops\nG0 Y152 F4000 ; move in front of wiper pad\nG4 S1 ; pause\nM400 ; wait for moves to finish\nM117 Heating... ; progress indicator message on LCD\nM109 R{first_layer_temperature[0]} ; wait for extruder to reach printing temp\nM190 R{first_layer_bed_temperature[0]} ; wait for bed to reach printing temp\nG1 Z2 E0 F75 ; prime tiny bit of filament into the nozzle\nM117 Mini Printing... ; progress indicator message on LCD\nM221 S74 ; Printer specific extrusion modifier.
