end_gcode=M104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG28 ; home\nM84 ; disable motors
toolchange_gcode=
use_firmware_retraction=0
use_relative_e_distances=1
use_volumetric_e=0
variable_layer_height=1
wipe=1
z_offset=0
default_print_profile=0.20mm QUALITY @AKOSSEL
default_filament_profile=Generic PLA @AKOSSEL
[printer:Anycubic Kossel Linear Plus]
inherits=*common_akossel*
printer_model=AKLP
printer_variant=0.4
printer_notes=Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_Anycubic\nPRINTER_MODEL_AKLP\nPRINTER_HAS_BOWDEN\n
printer_notes=Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_Anycubic\nPRINTER_MODEL_AK\nPRINTER_HAS_BOWDEN\n
start_gcode=G21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nM107 ;start with the fan off\nM117 Homing X/Y ...\nG28 X0 Y0 ;move X/Y to min endstops\nM117 Homing Z ...\nG28 Z0 ;move Z to min endstops\nG1 Z15.0 F240 ;move the platform down 15mm\nM117 Heating ...\nM104 S[first_layer_temperature]\n ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature]\n ; wait for extruder temp\nM117 Start cleaning ...\nG92 E0 ;zero the extruded length\nG1 F200 E10 ;extrude 10mm of feed stock\nG92 E0 ;zero the extruded length again\nM117 Intro line ...\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z[first_layer_height] F5000.0 ; Move to start position\nG1 X0.1 Y200.0 Z[first_layer_height] F1500.0 E15 ; Draw the first line\nG1 X0.4 Y200.0 Z[first_layer_height] F5000.0 ; Move to side a little\nG1 X0.4 Y20 Z0.3[first_layer_height] F1500.0 E30 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 E-1 F500 ; Retract filiment by 1 mm\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.3 F240 ; Move over to prevent blob squish\nG92 E0 ; Reset Extruder\nM117 Printing...\n
end_gcode=M117 Cooling down...\nM104 S0 ; turn off extruder\nM140 S0 ; turn off heatbed\nM107 ; Fan off\nM84 ; disable motors\nG91 ;relative positioning\nG1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-5 ;X-20 Y-20 F240 ;move Z up a bit and retract filament even more\nG28 X0 ;move X to min endstops, so the head is out of the way\nG90 ;Absolute positionning\nG1 Y200 F3000 ;Present print\nM84 ;steppers off\nM300 P300 S4000\nM117 Finished.\n
toolchange_gcode=
use_firmware_retraction=0
use_relative_e_distances=1
use_volumetric_e=0
variable_layer_height=1
wipe=1
z_offset=0
printer_model=
default_print_profile=
default_filament_profile=
[printer:Anycubic Mega Zero]
inherits=*common_mega0*
printer_model=MEGA0
printer_variant=0.4
max_layer_height=0.3
min_layer_height=0.1
printer_notes=Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_ANYCUBIC\nPRINTER_MODEL_MEGA0
bed_shape=0x0,220x0,220x220,0x220
max_print_height=250
machine_max_acceleration_e=5000
machine_max_acceleration_extruding=500
machine_max_acceleration_retracting=500
machine_max_acceleration_x=500
machine_max_acceleration_y=500
machine_max_acceleration_z=100
machine_max_feedrate_e=25
machine_max_feedrate_x=500
machine_max_feedrate_y=500
machine_max_feedrate_z=5
machine_max_jerk_e=5
machine_max_jerk_x=10
machine_max_jerk_y=10
machine_max_jerk_z=0.4
machine_min_extruding_rate=0
machine_min_travel_rate=0
nozzle_diameter=0.4
retract_before_travel=2
retract_layer_change=0
retract_length=7
retract_speed=30
retract_lift=0.2
deretract_speed=30
retract_before_wipe=70%
default_print_profile=0.20mm NORMAL @MEGA0
default_filament_profile=Anycubic PLA @MEGA0
start_gcode=G21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nM107 ;start with the fan off\nM117 Homing X/Y ...\nG28 X0 Y0 ;move X/Y to min endstops\nM117 Homing Z ...\nG28 Z0 ;move Z to min endstops\nG1 Z15.0 F240 ;move the platform down 15mm\nM117 Heating ...\nM104 S[first_layer_temperature]\n ; set extruder temp\nM109 S[first_layer_temperature]\n ; wait for extruder temp\nM117 Start cleaning ...\nG92 E0 ;zero the extruded length\nG1 F200 E10 ;extrude 10mm of feed stock\nG92 E0 ;zero the extruded length again\nM117 Intro line ...\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z[first_layer_height] F5000.0 ; Move to start position\nG1 X0.1 Y200.0 Z[first_layer_height] F1500.0 E15 ; Draw the first line\nG1 X0.4 Y200.0 Z[first_layer_height] F5000.0 ; Move to side a little\nG1 X0.4 Y20 Z0.3[first_layer_height] F1500.0 E30 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 E-1 F500 ; Retract filiment by 1 mm\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.3 F240 ; Move over to prevent blob squish\nG92 E0 ; Reset Extruder\nM117 Printing...\n
end_gcode=M117 Cooling down...\nM104 S0 ; turn off extruder\nM107 ; Fan off\nM84 ; disable motors\nG91 ;relative positioning\nG1 E-1 F300 ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-5 ;X-20 Y-20 F240 ;move Z up a bit and retract filament even more\nG28 X0 ;move X to min endstops, so the head is out of the way\nG90 ;Absolute positionning\nG1 Y200 F3000 ;Present print\nM84 ;steppers off\nM300 P300 S4000\nM117 Finished.\n
filament_notes="SainSmart TPU gains popularity among 3D Printing community for its balance of rigidity and flexibility. In addition, with a 95A Shore Hardness and improved bed adhesion, it is easier to print even with a stock elementary 3D Printer like the Creality Ender 3. SainSmart TPU will not disappoint if you are looking for flexible filament. From drone parts, phone cases, to small toys, all can be printed with ease.\n\nhttps://www.sainsmart.com/collections/tpu-filament/products/all-colors-tpu-flexible-filament-1-75mm-0-8kg-1-76lb"
filament_retract_before_travel=5
filament_retract_length=4
filament_retract_speed=40
filament_unloading_speed=90
first_layer_bed_temperature=55
first_layer_temperature=235
full_fan_speed_layer=6
max_fan_speed=80
min_fan_speed=80
slowdown_below_layer_time=10
temperature=235
[filament:*PETG_mega*]
inherits=*common_mega*
bed_temperature=90
bridge_fan_speed=50
fan_below_layer_time=20
filament_colour=#FF8000
filament_cost=27.82
filament_density=1.27
filament_max_volumetric_speed=8
filament_type=PETG
first_layer_bed_temperature=90
first_layer_temperature=230
max_fan_speed=50
min_fan_speed=30
temperature=240
[filament:Eolas Prints PLA @MEGA]
inherits=*PLA_mega*
filament_vendor=Eolas Prints
filament_cost=23.50
filament_density=1.24
filament_spool_weight=0
filament_colour=#4D9398
first_layer_bed_temperature=65
first_layer_temperature=212
temperature=208
bed_temperature=60
[filament:Eolas Prints PLA Matte @MEGA]
inherits=Eolas Prints PLA @MEGA
filament_cost=25.50
filament_max_volumetric_speed=14
temperature=212
[filament:Eolas Prints INGEO 850 @MEGA]
inherits=Eolas Prints PLA @MEGA
filament_cost=25.90
temperature=210
[filament:Eolas Prints INGEO 870 @MEGA]
inherits=Eolas Prints PLA @MEGA
filament_cost=25.90
temperature=215
first_layer_bed_temperature=68
first_layer_temperature=220
bed_temperature=65
[filament:Eolas Prints PETG @MEGA]
inherits=*PETG_mega*
filament_vendor=Eolas Prints
filament_cost=29.90
filament_density=1.27
filament_spool_weight=0
filament_colour=#4D9398
temperature=240
first_layer_bed_temperature=85
first_layer_temperature=235
bed_temperature=90
[filament:Eolas Prints PETG - UV Resistant @MEGA]
inherits=Eolas Prints PETG @MEGA
filament_cost=35.90
temperature=242
first_layer_temperature=237
[filament:Eolas Prints TPU 93A @MEGA]
inherits=*FLEX_mega*
filament_vendor=Eolas Prints
filament_cost=34.99
filament_density=1.21
filament_colour=#4D9398
filament_max_volumetric_speed=1.2
temperature=235
first_layer_bed_temperature=30
bed_temperature=30
filament_retract_length=0
extrusion_multiplier=1.16
[filament:Generic PETG @MEGA]
inherits=*PETG_mega*
[filament:ColorFabb XT-CF20 @MEGA]
inherits=*PETG_mega*
compatible_printers_condition=nozzle_diameter[0]>=0.4 and printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_I3_MEGA.*/
extrusion_multiplier=1.05
filament_colour=#804040
filament_cost=66.60
filament_density=1.35
filament_deretract_speed=25
filament_max_volumetric_speed=2
filament_notes="Based on colorFabb_XT, XT-CF20 is a carbon fiber composite material. Loaded with no less than 20% specially sourced carbon fibers we have developed a very stiff and tough 3D printing filament made for functional parts. It is truly a professional printers go-to material, especially for users looking for high melt strength, high melt viscosity and good dimensional accuracy and stability.\n\nhttps://colorfabb.com/xt-cf20"
filament_notes="HDglass is a high performance PETG type of 3D printer with unsurpassed 3D printing properties and improved mechanical strength, flexibility, toughness and heat resistance.\n\nhttps://www.formfutura.com/shop/product/hdglass-2812"
[filament:FormFutura ReForm rPET @MEGA]
inherits=*PETG_mega*
filament_vendor=FormFutura
filament_cost=26.65
filament_notes="ReForm rPET is a recycled PETG type of 3D printer filament that is made from post-industrial waste streams of a nearby located plastic bottle manufacturer.\n\nhttps://www.formfutura.com/shop/product/reform-rpet-2836"
filament_spool_weight=176
[filament:Janbex transparent PETG @MEGA]
inherits=*PETG_mega*
filament_vendor=Janbex
filament_cost=31.99
filament_spool_weight=222
first_layer_temperature=215
min_fan_speed=100
temperature=210
[filament:DAS FILAMENT PETG @MEGA]
inherits=*PETG_mega*
filament_vendor=DAS FILAMENT
bed_temperature=75
first_layer_bed_temperature=75
first_layer_temperature=220
temperature=225
[filament:*PLA_mega*]
inherits=*common_mega*
bed_temperature=60
disable_fan_first_layers=1
filament_colour=#FF3232
filament_cost=25.40
filament_density=1.24
filament_max_volumetric_speed=10
first_layer_bed_temperature=65
first_layer_temperature=215
min_fan_speed=100
temperature=210
[filament:Generic PLA @MEGA]
inherits=*PLA_mega*
[filament:3Dmensionals PLA @MEGA]
inherits=*PLA_mega*
filament_vendor=3Dmensionals
filament_cost=22.90
filament_notes="Das 3DFilaments - PLA von 3Dmensionals ist ein sehr leicht zu druckendes 3D-Drucker Filament. Dabei handelt es sich um ein etwas härteres PLA mit einer exzellenten thermischen Stabilität. Das Filament zeichnet sich vor allem durch verzugfreies 3D-Drucken aus und weist minimale bis keine Verformung nach dem Abkühlen auf. Daher ist es besonders gut für den Druck größerer Objekte geeignet. Zudem bietet 3DFilaments - PLA über die gesamte Fadenläge eine hervorragende Durchmesser- und Rundheitstoleranz.\n\nhttps://www.3dmensionals.de/3dfilaments?number=PSU3DM001V"
[filament:3D Warhorse PLA @MEGA]
inherits=*PLA_mega*
filament_vendor=3D Warhorse
filament_cost=19.99
[filament:AMOLEN wood PLA]
inherits=*PLA_mega*
filament_vendor=AMOLEN
compatible_printers_condition=nozzle_diameter[0]>0.35 and printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_I3_MEGA.*/
filament_notes="EasyFil PLA is an easy to print PLA type of 3D printer filament that is available in a wide variety of colors. Its improved flowing behavior make 3D printed layers flow more into each other.\n\nhttps://www.formfutura.com/shop/product/easyfil-pla-2801"
[filament:FormFutura ReForm rPLA @MEGA]
inherits=*PLA_mega*
filament_vendor=FormFutura
filament_cost=26.65
filament_notes="ReForm is a sustainable initiative within Formfutura to efficiently manage residual extrusion waste streams and re-use them into high-end upcycled filaments. The ideology behind ReForm is to a make 3D printing more sustainable – without having to make compromises on material properties – and yet keep it affordable.\n\nhttps://www.formfutura.com/shop/product/reform-rpla-2838"
[filament:GIANTARM PLA @MEGA]
inherits=*PLA_mega*
filament_vendor=GIANTARM
filament_cost=24.99
[filament:Prusament PLA @MEGA]
inherits=*PLA_mega*
filament_vendor=Prusa Polymers
filament_cost=30.24
filament_notes="Affordable filament for everyday printing in premium quality manufactured in-house by Josef Prusa"
end_gcode=G1 E-1.0 F2100 ; retract\nG92 E0.0\nG1{if max_layer_z < max_print_height} Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} E-34.0 F720 ; move print head up & retract filament\nG4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG1 X0 Y105 F3000 ; park print head\nM84 ; disable motors
extruder_colour=#808080
gcode_flavor=marlin
layer_gcode=;AFTER_LAYER_CHANGE\n;[layer_z]
max_layer_height=0.36
max_print_height=205
remaining_times=1
retract_before_travel=1.5
retract_before_wipe=60%
retract_layer_change=1
retract_length=6
retract_lift=0.075
retract_lift_below=204
retract_speed=40
silent_mode=0
start_gcode=G90 ; use absolute coordinates\nM83 ; extruder relative mode\nM204 S[machine_max_acceleration_extruding] T[machine_max_acceleration_retracting]\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nG28 ; home all\nG1 Y1.0 Z0.3 F1000 ; move print head up\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG92 E0.0\n; initial load\nG1 X205.0 E19 F1000\nG1 Y1.6\nG1 X5.0 E19 F1000\nG92 E0.0\n; intro line\nG1 Y2.0 Z0.2 F1000\nG1 X65.0 E9.0 F1000\nG1 X105.0 E12.5 F1000\nG92 E0.0
thumbnails=16x16,220x124
use_relative_e_distances=1
wipe=1
machine_max_acceleration_e=10000
machine_max_acceleration_extruding=1250
machine_max_acceleration_retracting=1250
machine_max_acceleration_x=3000
machine_max_acceleration_y=2000
machine_max_acceleration_z=60
machine_max_feedrate_e=60
machine_max_feedrate_x=500
machine_max_feedrate_y=500
machine_max_feedrate_z=6
machine_max_jerk_e=5
machine_max_jerk_x=10
machine_max_jerk_y=10
machine_max_jerk_z=0.4
[printer:Anycubic i3 Mega]
inherits=*common_mega*
printer_model=I3MEGA
printer_variant=0.4
printer_notes=Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_ANYCUBIC\nPRINTER_MODEL_I3_MEGA\nPRINTER_HAS_BOWDEN
[printer:Anycubic i3 Mega S]
inherits=*common_mega*
printer_model=I3MEGAS
printer_variant=0.4
printer_notes=Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_ANYCUBIC\nPRINTER_MODEL_I3_MEGA_S\nPRINTER_HAS_BOWDEN
compatible_printers_condition=printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_PREDATOR.*/ and printer_notes=~/.*PRINTER_HAS_BOWDEN.*/ and nozzle_diameter[0]==0.4
# Common print preset
[print:*common predator 0.6 nozzle*]
inherits=*common predator*
first_layer_height=0.24
infill_overlap=27%
compatible_printers_condition=printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_PREDATOR.*/ and printer_notes=~/.*PRINTER_HAS_BOWDEN.*/ and nozzle_diameter[0]==0.6
# Common print preset
[print:*common predator 0.8 nozzle*]
inherits=*common predator*
first_layer_height=0.32
infill_overlap=30%
compatible_printers_condition=printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_PREDATOR.*/ and printer_notes=~/.*PRINTER_HAS_BOWDEN.*/ and nozzle_diameter[0]==0.8
end_gcode=; end_gcode | start\n\n; v11 2020-11-14_11-27 tillverka\n\n; use relative positioning\n\nG91\n\n; retract the filament a bit before lifting the nozzle to release some of the pressure\n\nG1 E-1 F300\n\n; home\n\nG28\n\n; use absolute positioning\n\nG90\n\n; cooldown\n\nM104 S0\nM140 S0\n\n; end_gcode | end\n
before_layer_gcode=
layer_gcode=
toolchange_gcode=
between_objects_gcode=
retract_length=4
retract_lift=0.3
retract_lift_above=0
retract_lift_below=449
retract_speed=30
deretract_speed=0
retract_restart_extra=0
retract_before_travel=2
retract_layer_change=1
wipe=1
retract_before_wipe=70%
retract_length_toolchange=10
retract_restart_extra_toolchange=0
extruder_colour=#1193FF
machine_max_acceleration_e=3000
machine_max_acceleration_extruding=1000
machine_max_acceleration_retracting=1000
machine_max_acceleration_x=1500
machine_max_acceleration_y=1500
machine_max_acceleration_z=1500
machine_max_feedrate_e=60
machine_max_feedrate_x=200
machine_max_feedrate_y=200
machine_max_feedrate_z=200
machine_max_jerk_e=5
machine_max_jerk_x=5
machine_max_jerk_y=5
machine_max_jerk_z=5
machine_min_extruding_rate=0
machine_min_travel_rate=0
printer_settings_id=
printer_notes=Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_ANYCUBIC\nPRINTER_MODEL_PREDATOR\nPRINTER_HAS_BOWDEN\n
default_filament_profile=Generic PLA @4Max Pro 2.0
default_print_profile=0.20mm Quality @4Max Pro 2.0
deretract_speed=25
end_gcode=M104 S0 ; turn off extruder heating\nM140 S0 ; turn off bed heating\nM107 ; turn off fans\nG91 ; relative positioning\nG0 Z+0.5 ; move Z up a tiny bit\nG90 ; absolute positioning\nG0 X135 Y105 F{machine_max_feedrate_x[0]*60} ; move extruder to center position\nG0 Z190.5 F{machine_max_feedrate_z[0]*60} ; lower the plattform to Z min\nM84 ; steppers off\nG90 ; absolute positioning\n
extruder_offset=0x0
gcode_flavor=marlin
machine_limits_usage=time_estimate_only
machine_max_acceleration_e=5000
machine_max_acceleration_extruding=1250
machine_max_acceleration_retracting=1250
machine_max_acceleration_travel=1500
machine_max_acceleration_x=900
machine_max_acceleration_y=900
machine_max_acceleration_z=100
machine_max_feedrate_e=120
machine_max_feedrate_x=200
machine_max_feedrate_y=200
machine_max_feedrate_z=16
machine_max_jerk_e=5
machine_max_jerk_x=6
machine_max_jerk_y=6
machine_max_jerk_z=0.2
machine_min_extruding_rate=0
machine_min_travel_rate=0
max_layer_height=0.3
max_print_height=190
min_layer_height=0.07
nozzle_diameter=0.4
pause_print_gcode=M601
remaining_times=0
retract_before_travel=2
retract_before_wipe=0%
retract_layer_change=1
retract_length=2.5
retract_length_toolchange=10
retract_lift=0
retract_lift_above=0
retract_lift_below=0
retract_restart_extra=0
retract_restart_extra_toolchange=0
retract_speed=35
silent_mode=0
single_extruder_multi_material=0
start_gcode=G21 ; metric values\nG90 ; absolute positioning\nM82 ; set extruder to absolute mode\nM140 S[first_layer_bed_temperature] ; set bed temp\nG28 X0 Y0 ; home X and Y\nG28 Z0 ; home Z\nG1 Z30 F{machine_max_feedrate_z[0]*60} ; move Z a bit down to not blow on the bed edge while heating\nG1 X10 F3900 ; let some space on x to prevent the filament cooling exhaust from beeing blocked by the servo motor\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM104 S[first_layer_temperature] ; set extruder temp\nM106 S80 ; turn on fan to prevent air nozzle melt while heating up\nM109 S[first_layer_temperature] ; wait for extruder temp\nM107 ; start with the fan off\nG28 X0 ; goto X home again\nG92 E0 ; zero the extruded length\nG1 Z0.2 F360 ; move plattform upwards\n; extrude material next to the plattform (comment or remove following lines to disable)\nG1 F180 E20 ; extrude some material next to the plattform\nG92 E0 ; zero the extruded length\nG1 E-[retract_length] F{retract_speed[0]*60} ; do a filament retract\nG92 E0 ; zero the extruded length again\nG1 X5 F3900 ; move sideways to get rid of that string\nG1 E[retract_length] F{retract_speed[0]*60} ; do a filament deretract with retract parameters\nG92 E0 ; zero the extruded length again\n; draw intro line (comment or remove following lines to disable)\nG1 X30 E5 F700 ; draw intro line\nG92 E0 ; zero the extruded length\nG1 E-[retract_length] F{retract_speed[0]*60} ; do a filament retract\nG1 X40 Z2.0 ; move away from the introline\nG92 E0 ; zero the extruded length again\nG1 E[retract_length] F{retract_speed[0]*60} ; do a filament deretract with retract parameters\n; end of intro line code\nM117 Printing...\nG5
material_notes=#Distances are defined in mm, speeds are defined in mm/s.\n#Delay is defined in s.\nLIFT_DISTANCE=8.0\nLIFT_SPEED=2.5\nRETRACT_SPEED=3.0\nBOTTOM_LIFT_SPEED=2.0\nBOTTOM_LIFT_DISTANCE=9.0\nDELAY_BEFORE_EXPOSURE=0.5\nANTIALIASING=1
default_sla_material_profile=Generic Blue Resin @MONO 0.05
default_sla_print_profile=0.05 Normal @ANYCUBIC
thumbnails=224x168
sla_archive_format=pwmo
bed_shape=0x0,82.62x0,82.62x130.56,0x130.56
display_orientation=landscape
display_mirror_x=1
display_mirror_y=0
display_pixels_x=1620
display_pixels_y=2560
display_width=82.62
display_height=130.56
max_print_height=165
elefant_foot_compensation=0.2
elefant_foot_min_width=0.2
min_exposure_time=0.8
max_exposure_time=120
min_initial_exposure_time=0.8
max_initial_exposure_time=300
printer_correction=1,1,1
gamma_correction=1
area_fill=50
printer_notes=Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.'\nPRINTER_VENDOR_ANYCUBIC\nPRINTER_MODEL_PHOTONMONO\nPRINTER_TECHNOLOGY_SLA\n
[printer:Anycubic Photon Mono SE]
printer_technology=SLA
printer_model=PHOTON MONO SE
printer_variant=default
default_sla_material_profile=Generic Blue Resin @MONO 0.05
default_sla_print_profile=0.05 Normal @ANYCUBIC
thumbnails=224x168
sla_archive_format=pwms
bed_shape=0x0,82.62x0,82.62x130.56,0x130.56
display_orientation=landscape
display_mirror_x=1
display_mirror_y=0
display_pixels_x=1620
display_pixels_y=2560
display_width=82.62
display_height=130.56
max_print_height=160
elefant_foot_compensation=0.2
elefant_foot_min_width=0.2
min_exposure_time=0.8
max_exposure_time=120
min_initial_exposure_time=0.8
max_initial_exposure_time=300
printer_correction=1,1,1
gamma_correction=1
area_fill=45
printer_notes=Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.'\nPRINTER_VENDOR_ANYCUBIC\nPRINTER_MODEL_PHOTONMONOSE\nPRINTER_TECHNOLOGY_SLA\n
printer_notes=Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.'\nPRINTER_VENDOR_ANYCUBIC\nPRINTER_MODEL_PHOTONMONOX\nPRINTER_TECHNOLOGY_SLA\n
