filament_notes="List of materials which typically use standard PLA print settings:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladec PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"
[filament:Generic PETG @BIBO2]
inherits=*PET*
filament_vendor=Generic
[filament:Generic ABS @BIBO2]
inherits=*ABS*
first_layer_bed_temperature=90
bed_temperature=90
filament_vendor=Generic
filament_cost=27.82
filament_density=1.08
fan_always_on=0
cooling=0
min_fan_speed=15
max_fan_speed=15
slowdown_below_layer_time=20
disable_fan_first_layers=4
fan_below_layer_time=20
bridge_fan_speed=25
[filament:Esun ABS @BIBO2]
inherits=Generic ABS @BIBO2
filament_vendor=Esun
filament_cost=27.82
filament_density=1.08
fan_always_on=0
cooling=0
min_fan_speed=15
max_fan_speed=15
slowdown_below_layer_time=20
disable_fan_first_layers=4
fan_below_layer_time=20
bridge_fan_speed=25
[filament:Hatchbox ABS @BIBO2]
inherits=Generic ABS @BIBO2
filament_vendor=Hatchbox
filament_cost=27.82
filament_density=1.08
fan_always_on=0
cooling=0
min_fan_speed=15
max_fan_speed=15
slowdown_below_layer_time=20
disable_fan_first_layers=4
fan_below_layer_time=20
bridge_fan_speed=25
[filament:Generic HIPS @BIBO2]
inherits=*ABS*
filament_vendor=Generic
filament_cost=27.3
filament_density=1.04
bridge_fan_speed=50
cooling=1
extrusion_multiplier=1
fan_always_on=1
fan_below_layer_time=10
filament_colour=#FFFFD7
filament_soluble=1
filament_type=HIPS
first_layer_temperature=230
max_fan_speed=20
min_fan_speed=20
temperature=230
compatible_printers_condition=printer_notes=~/.*PRINTER_VENDOR_BIBO.*/ and num_extruders==2
deretract_speed=0 # By setting this value to 0 deretract used the retract_speed
extruder_colour=#FFFF00
extruder_offset=0x0
gcode_flavor=marlin
silent_mode=0
remaining_times=0
machine_max_acceleration_e=1100
machine_max_acceleration_extruding=5000
machine_max_acceleration_retracting=1100
machine_max_acceleration_x=500
machine_max_acceleration_y=500
machine_max_acceleration_z=100
machine_max_feedrate_e=20
machine_max_feedrate_x=350
machine_max_feedrate_y=350
machine_max_feedrate_z=2
machine_max_jerk_e=5
machine_max_jerk_x=8
machine_max_jerk_y=8
machine_max_jerk_z=0.3
machine_min_extruding_rate=0
machine_min_travel_rate=0
layer_gcode=;AFTER_LAYER_CHANGE\n;[layer_z]
max_layer_height=0.30
min_layer_height=0.05
max_print_height=160
printer_notes=
printer_settings_id=
printer_vendor=BIBO
retract_before_travel=1
retract_before_wipe=100%
retract_layer_change=1
retract_length=1.5
retract_length_toolchange=1.5
retract_lift=0
retract_lift_above=0
retract_lift_below=0
retract_restart_extra=0
retract_restart_extra_toolchange=0
retract_speed=20
single_extruder_multi_material=0
toolchange_gcode=
use_firmware_retraction=0
use_relative_e_distances=1
use_volumetric_e=0
variable_layer_height=1
wipe=1
z_offset=0
printer_model=
default_print_profile=
default_filament_profile=
[printer:BIBO2 Touch Dual extrusion]
inherits=*common*
printer_model=BIBO2
between_objects_gcode=
default_filament_profile=Generic PLA @BIBO2
default_print_profile=0.20mm NORMAL @BIBO2
deretract_speed=0,0 # Setting this value to 0 uses the retract speed
extruder_colour=#FFFF00;#229403
extruder_offset=0x0,0x0
layer_gcode=;AFTER_LAYER_CHANGE\n;[layer_z]
max_layer_height=0.3,0.3
min_layer_height=0.05,0.05
printer_notes=Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_BIBO\nPRINTER_MODEL_BIBO2
printer_settings_id=
printer_variant=0.4
nozzle_diameter=0.4,0.4
remaining_times=0
retract_before_travel=1,1
retract_before_wipe=100%,100%
retract_layer_change=1,1
retract_length=1.5,1.5
retract_length_toolchange=1.5,1.5
retract_lift=0,0
retract_lift_above=0,0
retract_lift_below=0,0
retract_restart_extra=0,0
retract_restart_extra_toolchange=0,0
retract_speed=20,20
start_gcode=;Start code PrusaSlicer BIBO 2 printers\nG21 ; set units to metric\nG90 ; absolute positioning\nM107 ; start with the fan off\nM190 S{max(first_layer_bed_temperature[0] - 5, first_layer_bed_temperature[1] - 5)} ; wait for bed temp\nM140 S{max(first_layer_bed_temperature[0], first_layer_bed_temperature[1])} ; continue bed heating to full temp while other things are happening\nM104 S{first_layer_temperature[0]} T0; set 1st nozzle heater to first layer temperature\nM104 S{first_layer_temperature[1]} T1; set 2nd nozzle heater to first layer temperature\nM105 ; Report Temperatures\nM109 S{first_layer_temperature[0]} T0; wait for 1st nozzle heat to first layer temperature\nM109 S{first_layer_temperature[1]} T1; wait for 2nd nozzle heat to first layer temperature\nM105 ; Report Temperatures\nG28 X0 Y0 ; move X/Y to min endstops\nG28 Z0 ; move Z to min endstops\nG1 Z2.0 F400 ; move the platform down 2mm\nT[initial_tool]; switch to initial tool position\nG92 E0.0 ; reset extruder\nG28 ; Home all axis\nG1 Y0 F1200 E0 ; move Y to min endstop and extrude 0 filament\nG92 E0.0 ; reset extruder and zero the current extruder coordinate before printing\nM117 BIBO now Printing... ; Put now printing message on screen
end_gcode=;BIBO End GCode\nM107 ; turn fans off\nG91 ; Relative positioning\nG1 Z1 F100\nM140 S0 ; Disable heated bed\nM104 T0 S0 ; extruder T0 heater off\nM104 T1 S0 ; extruder T1 heater off\nG1 Z+0.5 X-20 Y-20 F300 ; move Z down then move print head a bit out of the way\nG28 X0 Y0 ; move X/Y to min endstops, so the head is out of the way\nG90 ; Absolute positioning\nG92 E0.0 ; Reset extruder position\nM84 ; Turn steppers off\nM117 BIBO Print complete ; Put print complete message on screen
thumbnails=
toolchange_gcode=
use_relative_e_distances=1
wipe=1,1
z_offset=0
[printer:BIBO2 Touch E1 right only extrusion]
inherits=*common*
printer_model=BIBO2
printer_variant=0.4
extruder_colour=#FFFF00
printer_notes=Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_BIBO\nPRINTER_MODEL_BIBO2
nozzle_diameter=0.4
retract_before_travel=1
retract_length=1.5
retract_speed=20
deretract_speed=0 # Setting this value to 0 uses the retract speed
retract_before_wipe=100%
default_print_profile=0.20mm NORMAL @BIBO2
default_filament_profile=Generic PLA @BIBO2
start_gcode=;Start code PrusaSlicer BIBO 2 printers E1 only (i.e. T0)\nG21 ; set units to metric\nG90 ; absolute positioning\nM107 ; start with the fan off\nM190 S{first_layer_bed_temperature[0] - 5} ; wait for bed temp\nM140 S{first_layer_bed_temperature[0]} ; continue bed heating to full temp while other things are happening\nM104 S{first_layer_temperature[0]} T0 ; set 1st nozzle heater to first layer temperature\nM104 S{first_layer_temperature[0] * 0.791} T1 ; set 2nd nozzle heater to 79.1 percent standby temp\nM105 ; Report Temperatures\nM109 S{first_layer_temperature[0]} T0 ; wait for 1st nozzle heat to first layer temperature\nM109 S{first_layer_temperature[0] * 0.791} T1 ; wait for 2nd nozzle heat to 79.1 percent standby temp\nM105 ; Report Temperatures\nG28 X0 Y0 ; move X/Y to min endstops\nG28 Z0 ; move Z to min endstops\nG1 Y0 F1200 E0 ; move Y to min endstop and extrude 0 filament\nT[initial_tool] ; switch to initial tool position\nG92 E0.0 ; reset extruder\nG28 ; Home all axis\nG1 Y0 F1200 E0 ; move Y to min endstop and reset extruder\nG92 E0.0 ; zero the current extruder coordinate\nM117 Cleaning... ; Put Cleaning message on screen, Attempt Nozzle Wipe (for ooze free startup)\nG1 X-15.0 Y-92.9 Z0.3 F2400.0 ; move to start-line position\nG1 X15.0 Y-92.9 Z0.3 F1000.0 E2 ; draw 1st line\nG1 X15.0 Y-92.6 Z0.3 F3000.0 ; move to side a little\nG1 X-15.0 Y-92.6 Z0.3 F1000.0 E4 ; draw 2nd line\nG1 X-15.0 Y-92.3 Z0.3 F3000.0 ; move to side a little\nG1 X15.0 Y-92.3 Z0.3 F1000.0 E6 ; draw 3rd line\nG1 X15.0 Y-92 Z0.3 F3000.0 ; move to side a little\nG1 X-15.0 Y-92 Z0.3 F1000.0 E8 ; draw 4th line\nG92 E0.0 ; reset extruder and zero the current extruder coordinate before printing\nM117 BIBO E1 now Printing... ; Put now printing message on screen
end_gcode=;BIBO End GCode\nM107 ; turn fans off\nG91 ; Relative positioning\nG1 Z1 F100\nM140 S0 ; Disable heated bed\nM104 T0 S0 ; extruder T0 heater off\nM104 T1 S0 ; extruder T1 heater off\nG1 Z+0.5 X-20 Y-20 F300 ; move Z down then move print head a bit out of the way\nG28 X0 Y0 ; move X/Y to min endstops, so the head is out of the way\nG90 ; Absolute positioning\nG92 E0.0 ; Reset extruder position\nM84 ; Turn steppers off\nM117 BIBO Print complete ; Put print complete message on screen
thumbnails=
toolchange_gcode=
use_relative_e_distances=1
wipe=1
z_offset=0
[printer:BIBO2 Touch E2 left only extrusion]
inherits=*common*
printer_model=BIBO2
printer_variant=0.4
extruder_colour=#229403
printer_notes=Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_BIBO\nPRINTER_MODEL_BIBO2
nozzle_diameter=0.4
retract_before_travel=1
retract_length=1.5
retract_speed=20
deretract_speed=0 # Setting this value to 0 uses the retract speed
retract_before_wipe=100%
default_print_profile=0.20mm NORMAL @BIBO2
default_filament_profile=Generic PLA @BIBO2
start_gcode=;Start code PrusaSlicer BIBO 2 printers E2 only (i.e. T1)\nG21 ; set units to metric\nG90 ; absolute positioning\nM107 ; start with the fan off\nM140 S{first_layer_bed_temperature[0] - 5} ; set bed temp\nM105 ; Report Temperatures\nM190 S{first_layer_bed_temperature[0]} ; wait for bed temp\nM104 S{first_layer_temperature[0] * 0.791} T0 ; set 1st nozzle heater to 79.1 percent standby temp\nM104 S{first_layer_temperature[0]} T1 ; set 2nd nozzle heater to first layer temperature\nM105 ; Report Temperatures\nM109 S{first_layer_temperature[0] * 0.791} T0 ; set 1st nozzle heater to 79.1 percent standby temp\nM109 S{first_layer_temperature[0]} T1 ; Wait for 2nd nozzle heater to first layer temperature\nM105 ; Report Temperatures\nG28 X0 Y0 ; move X/Y to min endstops\nG28 Z0 ; move Z to min endstops\nG1 Z2 F400 ; move the print bed down 2mm\nT0 ; switch to tool position T0\nG90 ; absolute positioning\nG92 E0.0 ; zero the current extruder coordinate\nG28 ; Home all axis\nG1 Y0 F1200 E0 ; move Y to min endstop and reset extruder\nG92 E0.0 ; zero the current extruder coordinate\nT1 ; switch to tool position T1\nG92 E0.0 ; zero the current extruder coordinate\nM117 E2 nozzle wipe... ; Put Nozzle wipe message on screen, Attempt Nozzle Wipe (for ooze free startup)\nG1 X-15.0 Y-92.9 Z0.3 F2400.0 ; move to start-line position\nG1 X15.0 Y-92.9 Z0.3 F1000.0 E2 ; draw 1st line\nG1 X15.0 Y-92.6 Z0.3 F3000.0 ; move to side a little\nG1 X-15.0 Y-92.6 Z0.3 F1000.0 E4 ; draw 2nd line\nG1 X-15.0 Y-92.3 Z0.3 F3000.0 ; move to side a little\nG1 X15.0 Y-92.3 Z0.3 F1000.0 E6 ; draw 3rd line\nG1 X15.0 Y-92 Z0.3 F3000.0 ; move to side a little\nG1 X-15.0 Y-92 Z0.3 F1000.0 E8 ; draw 4th line\nG92 E0.0 ; reset extruder coordinate to zero before printing\nM117 BIBO Now Printing from E2... ; Put now printing message on screen
end_gcode=;BIBO End GCode\nM107 ; turn fans off\nG91 ; Relative positioning\nG1 Z1 F100\nM140 S0 ; Disable heated bed\nM104 T0 S0 ; extruder T0 heater off\nM104 T1 S0 ; extruder T1 heater off\nG1 Z+0.5 X-20 Y-20 F300 ; move Z down then move print head a bit out of the way\nG28 X0 Y0 ; move X/Y to min endstops, so the head is out of the way\nG90 ; Absolute positioning\nG92 E0.0 ; Reset extruder position\nM84 ; Turn steppers off\nM117 BIBO Print complete ; Put print complete message on screen
thumbnails=
toolchange_gcode=
use_relative_e_distances=1
wipe=1
z_offset=0
# Ditto Printing options with custom beds and special start end gcode for print duplication from one nozzle to the other
[printer:BIBO2 E1 right E2 Ditto]
inherits=BIBO2 Touch E1 right only extrusion
printer_model=BIBO2
printer_notes=Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_BIBO\nPRINTER_MODEL_BIBO2
start_gcode=;Start code PrusaSlicer BIBO 2 printers E1 only (i.e. T0)\nM420 S1 ; Turn on Ditto Printing\nG21 ; set units to metric\nG90 ; absolute positioning\nM107 ; start with the fan off\nM190 S{first_layer_bed_temperature[0] - 5} ; wait for bed temp\nM140 S{first_layer_bed_temperature[0]} ; continue bed heating to full temp while other things are happening\nM104 S{first_layer_temperature[0]} T0 ; set 1st nozzle heater to first layer temperature\nM104 S{first_layer_temperature[0]} T1 ; set 2nd nozzle heater to same first layer temperature\nM105 ; Report Temperatures\nM109 S{first_layer_temperature[0]} T0 ; wait for 1st nozzle heat to first layer temperature\nM109 S{first_layer_temperature[0]} T1 ; wait for 2nd nozzle heat to same first layer temperature\nM105 ; Report Temperatures\nG28 X0 Y0 ; move X/Y to min endstops\nG28 Z0 ; move Z to min endstops\nG1 Y0 F1200 E0 ; move Y to min endstop and extrude 0 filament\nT[initial_tool] ; switch to initial tool position\nG92 E0.0 ; reset extruder\nG28 ; Home all axis\nG1 Y0 F1200 E0 ; move Y to min endstop and reset extruder\nG92 E0.0 ; zero the current extruder coordinate\nM117 Cleaning... ; Put Cleaning message on screen, Attempt Nozzle Wipe (for ooze free startup)\nG1 X-15.0 Y-92.9 Z0.3 F2400.0 ; move to start-line position\nG1 X15.0 Y-92.9 Z0.3 F1000.0 E2 ; draw 1st line\nG1 X15.0 Y-92.6 Z0.3 F3000.0 ; move to side a little\nG1 X-15.0 Y-92.6 Z0.3 F1000.0 E4 ; draw 2nd line\nG1 X-15.0 Y-92.3 Z0.3 F3000.0 ; move to side a little\nG1 X15.0 Y-92.3 Z0.3 F1000.0 E6 ; draw 3rd line\nG1 X15.0 Y-92 Z0.3 F3000.0 ; move to side a little\nG1 X-15.0 Y-92 Z0.3 F1000.0 E8 ; draw 4th line\nG92 E0.0 ; reset extruder and zero the current extruder coordinate before printing\nM117 BIBO E1 now Printing... ; Put now printing message on screen
end_gcode=;BIBO End GCode\nM107 ; turn fans off\nG91 ; Relative positioning\nG1 Z1 F100\nM140 S0 ; Disable heated bed\nM104 T0 S0 ; extruder T0 heater off\nM104 T1 S0 ; extruder T1 heater off\nG1 Z+0.5 X-20 Y-20 F300 ; move Z down then move print head a bit out of the way\nG28 X0 Y0 ; move X/Y to min endstops, so the head is out of the way\nG90 ; Absolute positioning\nG92 E0.0 ; Reset extruder position\nM84 ; Turn steppers off\nM420 S0 ; Turn off Ditto Printing function\nM117 BIBO Print complete ; Put print complete message on screen
[printer:BIBO2 E2 left E1 Ditto]
inherits=BIBO2 Touch E2 left only extrusion
printer_model=BIBO2
printer_notes=Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_BIBO\nPRINTER_MODEL_BIBO2
start_gcode=;Start code PrusaSlicer BIBO 2 printers E2 only (i.e. T1)\nM420 S1 ; Turn on Ditto Printing\nG21 ; set units to metric\nG90 ; absolute positioning\nM107 ; start with the fan off\nM140 S{first_layer_bed_temperature[0] - 5} ; set bed temp\nM105 ; Report Temperatures\nM190 S{first_layer_bed_temperature[0]} ; wait for bed temp\nM104 S{first_layer_temperature[0]} T0 ; set 1st nozzle heater to ditto print temperature\nM104 S{first_layer_temperature[0]} T1 ; set 2nd nozzle heater to first layer temperature\nM105 ; Report Temperatures\nM109 S{first_layer_temperature[0]} T0 ; set 1st nozzle heater to ditto printing temperature\nM109 S{first_layer_temperature[0]} T1 ; Wait for 2nd nozzle heater to first layer temperature\nM105 ; Report Temperatures\nG28 X0 Y0 ; move X/Y to min endstops\nG28 Z0 ; move Z to min endstops\nG1 Z2 F400 ; move the print bed down 2mm\nT0 ; switch to tool position T0\nG90 ; absolute positioning\nG92 E0.0 ; zero the current extruder coordinate\nG28 ; Home all axis\nG1 Y0 F1200 E0 ; move Y to min endstop and reset extruder\nG92 E0.0 ; zero the current extruder coordinate\nT1 ; switch to tool position T1\nG92 E0.0 ; zero the current extruder coordinate\nM117 E2 nozzle wipe... ; Put Nozzle wipe message on screen, Attempt Nozzle Wipe (for ooze free startup)\nG1 X-15.0 Y-92.9 Z0.3 F2400.0 ; move to start-line position\nG1 X15.0 Y-92.9 Z0.3 F1000.0 E2 ; draw 1st line\nG1 X15.0 Y-92.6 Z0.3 F3000.0 ; move to side a little\nG1 X-15.0 Y-92.6 Z0.3 F1000.0 E4 ; draw 2nd line\nG1 X-15.0 Y-92.3 Z0.3 F3000.0 ; move to side a little\nG1 X15.0 Y-92.3 Z0.3 F1000.0 E6 ; draw 3rd line\nG1 X15.0 Y-92 Z0.3 F3000.0 ; move to side a little\nG1 X-15.0 Y-92 Z0.3 F1000.0 E8 ; draw 4th line\nG92 E0.0 ; reset extruder coordinate to zero before printing\nM117 BIBO Now Printing from E2... ; Put now printing message on screen
end_gcode=;BIBO End GCode\nM107 ; turn fans off\nG91 ; Relative positioning\nG1 Z1 F100\nM140 S0 ; Disable heated bed\nM104 T0 S0 ; extruder T0 heater off\nM104 T1 S0 ; extruder T1 heater off\nG1 Z+0.5 X-20 Y-20 F300 ; move Z down then move print head a bit out of the way\nG28 X0 Y0 ; move X/Y to min endstops, so the head is out of the way\nG90 ; Absolute positioning\nG92 E0.0 ; Reset extruder position\nM84 ; Turn steppers off\nM420 S0 ; Turn off Ditto Printing function\nM117 BIBO Print complete ; Put print complete message on screen
