From 68a570221b995b91acf3a0489a538c95c27965a6 Mon Sep 17 00:00:00 2001 From: Vojtech Kral Date: Mon, 30 Apr 2018 17:10:04 +0200 Subject: [PATCH] avrdude.conf: Remove unsupported stuff --- resources/avrdude/avrdude.conf | 1190 ++++++++++++++++---------------- 1 file changed, 595 insertions(+), 595 deletions(-) diff --git a/resources/avrdude/avrdude.conf b/resources/avrdude/avrdude.conf index 32110344d..d008995d8 100644 --- a/resources/avrdude/avrdude.conf +++ b/resources/avrdude/avrdude.conf @@ -382,227 +382,227 @@ programmer # the way the Multi-Protocol Synchronous Serial Engine (MPSSE) of # these FTDI ICs has been designed. -programmer - id = "avrftdi"; - desc = "FT2232D based generic programmer"; - type = "avrftdi"; - connection_type = usb; - usbvid = 0x0403; - usbpid = 0x6010; - usbvendor = ""; - usbproduct = ""; - usbdev = "A"; - usbsn = ""; -#ISP-signals - lower ADBUS-Nibble (default) - reset = 3; - sck = 0; - mosi = 1; - miso = 2; -#LED SIGNALs - higher ADBUS-Nibble -# errled = 4; -# rdyled = 5; -# pgmled = 6; -# vfyled = 7; -#Buffer Signal - ACBUS - Nibble -# buff = 8; -; +# programmer +# id = "avrftdi"; +# desc = "FT2232D based generic programmer"; +# type = "avrftdi"; +# connection_type = usb; +# usbvid = 0x0403; +# usbpid = 0x6010; +# usbvendor = ""; +# usbproduct = ""; +# usbdev = "A"; +# usbsn = ""; +# #ISP-signals - lower ADBUS-Nibble (default) +# reset = 3; +# sck = 0; +# mosi = 1; +# miso = 2; +# #LED SIGNALs - higher ADBUS-Nibble +# # errled = 4; +# # rdyled = 5; +# # pgmled = 6; +# # vfyled = 7; +# #Buffer Signal - ACBUS - Nibble +# # buff = 8; +# ; # This is an implementation of the above with a buffer IC (74AC244) and # 4 LEDs directly attached, all active low. -programmer - id = "2232HIO"; - desc = "FT2232H based generic programmer"; - type = "avrftdi"; - connection_type = usb; - usbvid = 0x0403; -# Note: This PID is reserved for generic H devices and -# should be programmed into the EEPROM -# usbpid = 0x8A48; - usbpid = 0x6010; - usbdev = "A"; - usbvendor = ""; - usbproduct = ""; - usbsn = ""; -#ISP-signals - reset = 3; - sck = 0; - mosi = 1; - miso = 2; - buff = ~4; -#LED SIGNALs - errled = ~ 11; - rdyled = ~ 14; - pgmled = ~ 13; - vfyled = ~ 12; -; +# programmer +# id = "2232HIO"; +# desc = "FT2232H based generic programmer"; +# type = "avrftdi"; +# connection_type = usb; +# usbvid = 0x0403; +# # Note: This PID is reserved for generic H devices and +# # should be programmed into the EEPROM +# # usbpid = 0x8A48; +# usbpid = 0x6010; +# usbdev = "A"; +# usbvendor = ""; +# usbproduct = ""; +# usbsn = ""; +# #ISP-signals +# reset = 3; +# sck = 0; +# mosi = 1; +# miso = 2; +# buff = ~4; +# #LED SIGNALs +# errled = ~ 11; +# rdyled = ~ 14; +# pgmled = ~ 13; +# vfyled = ~ 12; +# ; -#The FT4232H can be treated as FT2232H, but it has a different USB -#device ID of 0x6011. -programmer parent "avrftdi" - id = "4232h"; - desc = "FT4232H based generic programmer"; - usbpid = 0x6011; -; +# #The FT4232H can be treated as FT2232H, but it has a different USB +# #device ID of 0x6011. +# programmer parent "avrftdi" +# id = "4232h"; +# desc = "FT4232H based generic programmer"; +# usbpid = 0x6011; +# ; -programmer - id = "jtagkey"; - desc = "Amontec JTAGKey, JTAGKey-Tiny and JTAGKey2"; - type = "avrftdi"; - connection_type = usb; - usbvid = 0x0403; -# Note: This PID is used in all JTAGKey variants - usbpid = 0xCFF8; - usbdev = "A"; - usbvendor = ""; - usbproduct = ""; - usbsn = ""; -#ISP-signals => 20 - Pin connector on JTAGKey - reset = 3; # TMS 7 violet - sck = 0; # TCK 9 white - mosi = 1; # TDI 5 green - miso = 2; # TDO 13 orange - buff = ~4; -# VTG VREF 1 brown with red tip -# GND GND 20 black -# The colors are on the 20 pin breakout cable -# from Amontec -; +# programmer +# id = "jtagkey"; +# desc = "Amontec JTAGKey, JTAGKey-Tiny and JTAGKey2"; +# type = "avrftdi"; +# connection_type = usb; +# usbvid = 0x0403; +# # Note: This PID is used in all JTAGKey variants +# usbpid = 0xCFF8; +# usbdev = "A"; +# usbvendor = ""; +# usbproduct = ""; +# usbsn = ""; +# #ISP-signals => 20 - Pin connector on JTAGKey +# reset = 3; # TMS 7 violet +# sck = 0; # TCK 9 white +# mosi = 1; # TDI 5 green +# miso = 2; # TDO 13 orange +# buff = ~4; +# # VTG VREF 1 brown with red tip +# # GND GND 20 black +# # The colors are on the 20 pin breakout cable +# # from Amontec +# ; -# UM232H module from FTDI and Glyn.com.au. -# See helix.air.net.au for detailed usage information. -# J1: Connect pin 2 and 3 for USB power. -# J2: Connect pin 2 and 3 for USB power. -# J2: Pin 7 is SCK -# : Pin 8 is MOSI -# : Pin 9 is MISO -# : Pin 11 is RST -# : Pin 6 is ground -# Use the -b flag to set the SPI clock rate eg -b 3750000 is the fastest I could get -# a 16MHz Atmega1280 to program reliably. The 232H is conveniently 5V tolerant. -programmer - id = "UM232H"; - desc = "FT232H based module from FTDI and Glyn.com.au"; - type = "avrftdi"; - usbvid = 0x0403; -# Note: This PID is reserved for generic 232H devices and -# should be programmed into the EEPROM - usbpid = 0x6014; - usbdev = "A"; - usbvendor = ""; - usbproduct = ""; - usbsn = ""; -#ISP-signals - sck = 0; - mosi = 1; - miso = 2; - reset = 3; -; +# # UM232H module from FTDI and Glyn.com.au. +# # See helix.air.net.au for detailed usage information. +# # J1: Connect pin 2 and 3 for USB power. +# # J2: Connect pin 2 and 3 for USB power. +# # J2: Pin 7 is SCK +# # : Pin 8 is MOSI +# # : Pin 9 is MISO +# # : Pin 11 is RST +# # : Pin 6 is ground +# # Use the -b flag to set the SPI clock rate eg -b 3750000 is the fastest I could get +# # a 16MHz Atmega1280 to program reliably. The 232H is conveniently 5V tolerant. +# programmer +# id = "UM232H"; +# desc = "FT232H based module from FTDI and Glyn.com.au"; +# type = "avrftdi"; +# usbvid = 0x0403; +# # Note: This PID is reserved for generic 232H devices and +# # should be programmed into the EEPROM +# usbpid = 0x6014; +# usbdev = "A"; +# usbvendor = ""; +# usbproduct = ""; +# usbsn = ""; +# #ISP-signals +# sck = 0; +# mosi = 1; +# miso = 2; +# reset = 3; +# ; -# C232HM module from FTDI and Glyn.com.au. -# : Orange is SCK -# : Yellow is MOSI -# : Green is MISO -# : Brown is RST -# : Black is ground -# Use the -b flag to set the SPI clock rate eg -b 3750000 is the fastest I could get -# a 16MHz Atmega1280 to program reliably. The 232H is conveniently 5V tolerant. -programmer - id = "C232HM"; - desc = "FT232H based module from FTDI and Glyn.com.au"; - type = "avrftdi"; - usbvid = 0x0403; -# Note: This PID is reserved for generic 232H devices and -# should be programmed into the EEPROM - usbpid = 0x6014; - usbdev = "A"; - usbvendor = ""; - usbproduct = ""; - usbsn = ""; -#ISP-signals - sck = 0; - mosi = 1; - miso = 2; - reset = 3; -; +# # C232HM module from FTDI and Glyn.com.au. +# # : Orange is SCK +# # : Yellow is MOSI +# # : Green is MISO +# # : Brown is RST +# # : Black is ground +# # Use the -b flag to set the SPI clock rate eg -b 3750000 is the fastest I could get +# # a 16MHz Atmega1280 to program reliably. The 232H is conveniently 5V tolerant. +# programmer +# id = "C232HM"; +# desc = "FT232H based module from FTDI and Glyn.com.au"; +# type = "avrftdi"; +# usbvid = 0x0403; +# # Note: This PID is reserved for generic 232H devices and +# # should be programmed into the EEPROM +# usbpid = 0x6014; +# usbdev = "A"; +# usbvendor = ""; +# usbproduct = ""; +# usbsn = ""; +# #ISP-signals +# sck = 0; +# mosi = 1; +# miso = 2; +# reset = 3; +# ; -# On the adapter you can read "O-Link". On the PCB is printed "OpenJTAG v3.1" -# You can find it as "OpenJTAG ARM JTAG USB" in the internet. -# (But there are also several projects called Open JTAG, eg. -# http://www.openjtag.org, which are completely different.) -# http://www.100ask.net/shop/english.html (website seems to be outdated) -# http://item.taobao.com/item.htm?id=1559277013 -# http://www.micro4you.com/store/openjtag-arm-jtag-usb.html (schematics!) -# some other sources which call it O-Link -# http://www.andahammer.com/olink/ -# http://www.developmentboard.net/31-o-link-debugger.html -# http://armwerks.com/catalog/o-link-debugger-copy/ -# or just have a look at ebay ... -# It is basically the same entry as jtagkey with different usb ids. -programmer parent "jtagkey" - id = "o-link"; - desc = "O-Link, OpenJTAG from www.100ask.net"; - usbvid = 0x1457; - usbpid = 0x5118; - usbvendor = "www.100ask.net"; - usbproduct = "USB<=>JTAG&RS232"; -; +# # On the adapter you can read "O-Link". On the PCB is printed "OpenJTAG v3.1" +# # You can find it as "OpenJTAG ARM JTAG USB" in the internet. +# # (But there are also several projects called Open JTAG, eg. +# # http://www.openjtag.org, which are completely different.) +# # http://www.100ask.net/shop/english.html (website seems to be outdated) +# # http://item.taobao.com/item.htm?id=1559277013 +# # http://www.micro4you.com/store/openjtag-arm-jtag-usb.html (schematics!) +# # some other sources which call it O-Link +# # http://www.andahammer.com/olink/ +# # http://www.developmentboard.net/31-o-link-debugger.html +# # http://armwerks.com/catalog/o-link-debugger-copy/ +# # or just have a look at ebay ... +# # It is basically the same entry as jtagkey with different usb ids. +# programmer parent "jtagkey" +# id = "o-link"; +# desc = "O-Link, OpenJTAG from www.100ask.net"; +# usbvid = 0x1457; +# usbpid = 0x5118; +# usbvendor = "www.100ask.net"; +# usbproduct = "USB<=>JTAG&RS232"; +# ; -# http://wiki.openmoko.org/wiki/Debug_Board_v3 -programmer - id = "openmoko"; - desc = "Openmoko debug board (v3)"; - type = "avrftdi"; - usbvid = 0x1457; - usbpid = 0x5118; - usbdev = "A"; - usbvendor = ""; - usbproduct = ""; - usbsn = ""; - reset = 3; # TMS 7 - sck = 0; # TCK 9 - mosi = 1; # TDI 5 - miso = 2; # TDO 13 -; +# # http://wiki.openmoko.org/wiki/Debug_Board_v3 +# programmer +# id = "openmoko"; +# desc = "Openmoko debug board (v3)"; +# type = "avrftdi"; +# usbvid = 0x1457; +# usbpid = 0x5118; +# usbdev = "A"; +# usbvendor = ""; +# usbproduct = ""; +# usbsn = ""; +# reset = 3; # TMS 7 +# sck = 0; # TCK 9 +# mosi = 1; # TDI 5 +# miso = 2; # TDO 13 +# ; -# Only Rev. A boards. -# Schematic and user manual: http://www.cs.put.poznan.pl/wswitala/download/pdf/811EVBK.pdf -programmer - id = "lm3s811"; - desc = "Luminary Micro LM3S811 Eval Board (Rev. A)"; - type = "avrftdi"; - connection_type = usb; - usbvid = 0x0403; - usbpid = 0xbcd9; - usbvendor = "LMI"; - usbproduct = "LM3S811 Evaluation Board"; - usbdev = "A"; - usbsn = ""; -#ISP-signals - lower ACBUS-Nibble (default) - reset = 3; - sck = 0; - mosi = 1; - miso = 2; -# Enable correct buffers - buff = 7; -; +# # Only Rev. A boards. +# # Schematic and user manual: http://www.cs.put.poznan.pl/wswitala/download/pdf/811EVBK.pdf +# programmer +# id = "lm3s811"; +# desc = "Luminary Micro LM3S811 Eval Board (Rev. A)"; +# type = "avrftdi"; +# connection_type = usb; +# usbvid = 0x0403; +# usbpid = 0xbcd9; +# usbvendor = "LMI"; +# usbproduct = "LM3S811 Evaluation Board"; +# usbdev = "A"; +# usbsn = ""; +# #ISP-signals - lower ACBUS-Nibble (default) +# reset = 3; +# sck = 0; +# mosi = 1; +# miso = 2; +# # Enable correct buffers +# buff = 7; +# ; -# submitted as bug #46020 -programmer - id = "tumpa"; - desc = "TIAO USB Multi-Protocol Adapter"; - type = "avrftdi"; - connection_type = usb; - usbvid = 0x0403; - usbpid = 0x8A98; - usbdev = "A"; - usbvendor = "TIAO"; - usbproduct = ""; - usbsn = ""; - sck = 0; # TCK 9 - mosi = 1; # TDI 5 - miso = 2; # TDO 13 - reset = 3; # TMS 7 -; +# # submitted as bug #46020 +# programmer +# id = "tumpa"; +# desc = "TIAO USB Multi-Protocol Adapter"; +# type = "avrftdi"; +# connection_type = usb; +# usbvid = 0x0403; +# usbpid = 0x8A98; +# usbdev = "A"; +# usbvendor = "TIAO"; +# usbproduct = ""; +# usbsn = ""; +# sck = 0; # TCK 9 +# mosi = 1; # TDI 5 +# miso = 2; # TDO 13 +# reset = 3; # TMS 7 +# ; programmer id = "avrisp"; @@ -618,16 +618,16 @@ programmer connection_type = serial; ; -programmer - id = "avrispmkII"; - desc = "Atmel AVR ISP mkII"; - type = "stk500v2"; - connection_type = usb; -; +# programmer +# id = "avrispmkII"; +# desc = "Atmel AVR ISP mkII"; +# type = "stk500v2"; +# connection_type = usb; +# ; -programmer parent "avrispmkII" - id = "avrisp2"; -; +# programmer parent "avrispmkII" +# id = "avrisp2"; +# ; programmer id = "buspirate"; @@ -696,26 +696,26 @@ programmer connection_type = serial; ; -programmer - id = "stk600"; - desc = "Atmel STK600"; - type = "stk600"; - connection_type = usb; -; +# programmer +# id = "stk600"; +# desc = "Atmel STK600"; +# type = "stk600"; +# connection_type = usb; +# ; -programmer - id = "stk600pp"; - desc = "Atmel STK600 in parallel programming mode"; - type = "stk600pp"; - connection_type = usb; -; +# programmer +# id = "stk600pp"; +# desc = "Atmel STK600 in parallel programming mode"; +# type = "stk600pp"; +# connection_type = usb; +# ; -programmer - id = "stk600hvsp"; - desc = "Atmel STK600 in high-voltage serial programming mode"; - type = "stk600hvsp"; - connection_type = usb; -; +# programmer +# id = "stk600hvsp"; +# desc = "Atmel STK600 in high-voltage serial programming mode"; +# type = "stk600hvsp"; +# connection_type = usb; +# ; programmer id = "avr910"; @@ -724,155 +724,155 @@ programmer connection_type = serial; ; -programmer - id = "ft245r"; - desc = "FT245R Synchronous BitBang"; - type = "ftdi_syncbb"; - connection_type = usb; - miso = 1; # D1 - sck = 0; # D0 - mosi = 2; # D2 - reset = 4; # D4 -; +# programmer +# id = "ft245r"; +# desc = "FT245R Synchronous BitBang"; +# type = "ftdi_syncbb"; +# connection_type = usb; +# miso = 1; # D1 +# sck = 0; # D0 +# mosi = 2; # D2 +# reset = 4; # D4 +# ; -programmer - id = "ft232r"; - desc = "FT232R Synchronous BitBang"; - type = "ftdi_syncbb"; - connection_type = usb; - miso = 1; # RxD - sck = 0; # TxD - mosi = 2; # RTS - reset = 4; # DTR -; +# programmer +# id = "ft232r"; +# desc = "FT232R Synchronous BitBang"; +# type = "ftdi_syncbb"; +# connection_type = usb; +# miso = 1; # RxD +# sck = 0; # TxD +# mosi = 2; # RTS +# reset = 4; # DTR +# ; -# see http://www.bitwizard.nl/wiki/index.php/FTDI_ATmega -programmer - id = "bwmega"; - desc = "BitWizard ftdi_atmega builtin programmer"; - type = "ftdi_syncbb"; - connection_type = usb; - miso = 5; # DSR - sck = 6; # DCD - mosi = 3; # CTS - reset = 7; # RI -; +# # see http://www.bitwizard.nl/wiki/index.php/FTDI_ATmega +# programmer +# id = "bwmega"; +# desc = "BitWizard ftdi_atmega builtin programmer"; +# type = "ftdi_syncbb"; +# connection_type = usb; +# miso = 5; # DSR +# sck = 6; # DCD +# mosi = 3; # CTS +# reset = 7; # RI +# ; -# see http://www.geocities.jp/arduino_diecimila/bootloader/index_en.html -# Note: pins are numbered from 1! -programmer - id = "arduino-ft232r"; - desc = "Arduino: FT232R connected to ISP"; - type = "ftdi_syncbb"; - connection_type = usb; - miso = 3; # CTS X3(1) - sck = 5; # DSR X3(2) - mosi = 6; # DCD X3(3) - reset = 7; # RI X3(4) -; +# # see http://www.geocities.jp/arduino_diecimila/bootloader/index_en.html +# # Note: pins are numbered from 1! +# programmer +# id = "arduino-ft232r"; +# desc = "Arduino: FT232R connected to ISP"; +# type = "ftdi_syncbb"; +# connection_type = usb; +# miso = 3; # CTS X3(1) +# sck = 5; # DSR X3(2) +# mosi = 6; # DCD X3(3) +# reset = 7; # RI X3(4) +# ; -# website mentioned above uses this id -programmer parent "arduino-ft232r" - id = "diecimila"; - desc = "alias for arduino-ft232r"; -; +# # website mentioned above uses this id +# programmer parent "arduino-ft232r" +# id = "diecimila"; +# desc = "alias for arduino-ft232r"; +# ; -# There is a ATmega328P kit PCB called "uncompatino". -# This board allows ISP via its on-board FT232R. -# This is designed like Arduino Duemilanove but has no standard ICPS header. -# Its 4 pairs of pins are shorted to enable ftdi_syncbb. -# http://akizukidenshi.com/catalog/g/gP-07487/ -# http://akizukidenshi.com/download/ds/akizuki/k6096_manual_20130816.pdf -programmer - id = "uncompatino"; - desc = "uncompatino with all pairs of pins shorted"; - type = "ftdi_syncbb"; - connection_type = usb; - miso = 3; # cts - sck = 5; # dsr - mosi = 6; # dcd - reset = 7; # ri -; +# # There is a ATmega328P kit PCB called "uncompatino". +# # This board allows ISP via its on-board FT232R. +# # This is designed like Arduino Duemilanove but has no standard ICPS header. +# # Its 4 pairs of pins are shorted to enable ftdi_syncbb. +# # http://akizukidenshi.com/catalog/g/gP-07487/ +# # http://akizukidenshi.com/download/ds/akizuki/k6096_manual_20130816.pdf +# programmer +# id = "uncompatino"; +# desc = "uncompatino with all pairs of pins shorted"; +# type = "ftdi_syncbb"; +# connection_type = usb; +# miso = 3; # cts +# sck = 5; # dsr +# mosi = 6; # dcd +# reset = 7; # ri +# ; -# FTDI USB to serial cable TTL-232R-5V with a custom adapter for ICSP -# http://www.ftdichip.com/Products/Cables/USBTTLSerial.htm -# http://www.ftdichip.com/Support/Documents/DataSheets/Cables/DS_TTL-232R_CABLES.pdf -# For ICSP pinout see for example http://www.atmel.com/images/doc2562.pdf -# (Figure 1. ISP6PIN header pinout and Table 1. Connections required for ISP ...) -# TTL-232R GND 1 Black -> ICPS GND (pin 6) -# TTL-232R CTS 2 Brown -> ICPS MOSI (pin 4) -# TTL-232R VCC 3 Red -> ICPS VCC (pin 2) -# TTL-232R TXD 4 Orange -> ICPS RESET (pin 5) -# TTL-232R RXD 5 Yellow -> ICPS SCK (pin 3) -# TTL-232R RTS 6 Green -> ICPS MISO (pin 1) -# Except for VCC and GND, you can connect arbitual pairs as long as -# the following table is adjusted. -programmer - id = "ttl232r"; - desc = "FTDI TTL232R-5V with ICSP adapter"; - type = "ftdi_syncbb"; - connection_type = usb; - miso = 2; # rts - sck = 1; # rxd - mosi = 3; # cts - reset = 0; # txd -; +# # FTDI USB to serial cable TTL-232R-5V with a custom adapter for ICSP +# # http://www.ftdichip.com/Products/Cables/USBTTLSerial.htm +# # http://www.ftdichip.com/Support/Documents/DataSheets/Cables/DS_TTL-232R_CABLES.pdf +# # For ICSP pinout see for example http://www.atmel.com/images/doc2562.pdf +# # (Figure 1. ISP6PIN header pinout and Table 1. Connections required for ISP ...) +# # TTL-232R GND 1 Black -> ICPS GND (pin 6) +# # TTL-232R CTS 2 Brown -> ICPS MOSI (pin 4) +# # TTL-232R VCC 3 Red -> ICPS VCC (pin 2) +# # TTL-232R TXD 4 Orange -> ICPS RESET (pin 5) +# # TTL-232R RXD 5 Yellow -> ICPS SCK (pin 3) +# # TTL-232R RTS 6 Green -> ICPS MISO (pin 1) +# # Except for VCC and GND, you can connect arbitual pairs as long as +# # the following table is adjusted. +# programmer +# id = "ttl232r"; +# desc = "FTDI TTL232R-5V with ICSP adapter"; +# type = "ftdi_syncbb"; +# connection_type = usb; +# miso = 2; # rts +# sck = 1; # rxd +# mosi = 3; # cts +# reset = 0; # txd +# ; -programmer - id = "usbasp"; - desc = "USBasp, http://www.fischl.de/usbasp/"; - type = "usbasp"; - connection_type = usb; - usbvid = 0x16C0; # VOTI - usbpid = 0x05DC; # Obdev's free shared PID - usbvendor = "www.fischl.de"; - usbproduct = "USBasp"; +# programmer +# id = "usbasp"; +# desc = "USBasp, http://www.fischl.de/usbasp/"; +# type = "usbasp"; +# connection_type = usb; +# usbvid = 0x16C0; # VOTI +# usbpid = 0x05DC; # Obdev's free shared PID +# usbvendor = "www.fischl.de"; +# usbproduct = "USBasp"; - # following variants are autodetected for id "usbasp" +# # following variants are autodetected for id "usbasp" - # original usbasp from fischl.de - # see above "usbasp" +# # original usbasp from fischl.de +# # see above "usbasp" - # old usbasp from fischl.de - #usbvid = 0x03EB; # ATMEL - #usbpid = 0xC7B4; # (unoffical) USBasp - #usbvendor = "www.fischl.de"; - #usbproduct = "USBasp"; +# # old usbasp from fischl.de +# #usbvid = 0x03EB; # ATMEL +# #usbpid = 0xC7B4; # (unoffical) USBasp +# #usbvendor = "www.fischl.de"; +# #usbproduct = "USBasp"; - # NIBObee (only if -P nibobee is given on command line) - # see below "nibobee" -; +# # NIBObee (only if -P nibobee is given on command line) +# # see below "nibobee" +# ; -programmer - id = "nibobee"; - desc = "NIBObee"; - type = "usbasp"; - connection_type = usb; - usbvid = 0x16C0; # VOTI - usbpid = 0x092F; # NIBObee PID - usbvendor = "www.nicai-systems.com"; - usbproduct = "NIBObee"; -; +# programmer +# id = "nibobee"; +# desc = "NIBObee"; +# type = "usbasp"; +# connection_type = usb; +# usbvid = 0x16C0; # VOTI +# usbpid = 0x092F; # NIBObee PID +# usbvendor = "www.nicai-systems.com"; +# usbproduct = "NIBObee"; +# ; -programmer - id = "usbasp-clone"; - desc = "Any usbasp clone with correct VID/PID"; - type = "usbasp"; - connection_type = usb; - usbvid = 0x16C0; # VOTI - usbpid = 0x05DC; # Obdev's free shared PID - #usbvendor = ""; - #usbproduct = ""; -; +# programmer +# id = "usbasp-clone"; +# desc = "Any usbasp clone with correct VID/PID"; +# type = "usbasp"; +# connection_type = usb; +# usbvid = 0x16C0; # VOTI +# usbpid = 0x05DC; # Obdev's free shared PID +# #usbvendor = ""; +# #usbproduct = ""; +# ; -programmer - id = "usbtiny"; - desc = "USBtiny simple USB programmer, http://www.ladyada.net/make/usbtinyisp/"; - type = "usbtiny"; - connection_type = usb; - usbvid = 0x1781; - usbpid = 0x0c9f; -; +# programmer +# id = "usbtiny"; +# desc = "USBtiny simple USB programmer, http://www.ladyada.net/make/usbtinyisp/"; +# type = "usbtiny"; +# connection_type = usb; +# usbvid = 0x1781; +# usbpid = 0x0c9f; +# ; programmer id = "butterfly"; @@ -907,240 +907,240 @@ programmer parent "mkbutterfly" id = "butterfly_mk"; ; -programmer - id = "jtagmkI"; - desc = "Atmel JTAG ICE (mkI)"; - baudrate = 115200; # default is 115200 - type = "jtagmki"; - connection_type = serial; -; +# programmer +# id = "jtagmkI"; +# desc = "Atmel JTAG ICE (mkI)"; +# baudrate = 115200; # default is 115200 +# type = "jtagmki"; +# connection_type = serial; +# ; -# easier to type -programmer parent "jtagmkI" - id = "jtag1"; -; +# # easier to type +# programmer parent "jtagmkI" +# id = "jtag1"; +# ; -# easier to type -programmer parent "jtag1" - id = "jtag1slow"; - baudrate = 19200; -; +# # easier to type +# programmer parent "jtag1" +# id = "jtag1slow"; +# baudrate = 19200; +# ; -# The JTAG ICE mkII has both, serial and USB connectivity. As it is -# mostly used through USB these days (AVR Studio 5 only supporting it -# that way), we make connection_type = usb the default. Users are -# still free to use a serial port with the -P option. +# # The JTAG ICE mkII has both, serial and USB connectivity. As it is +# # mostly used through USB these days (AVR Studio 5 only supporting it +# # that way), we make connection_type = usb the default. Users are +# # still free to use a serial port with the -P option. -programmer - id = "jtagmkII"; - desc = "Atmel JTAG ICE mkII"; - baudrate = 19200; # default is 19200 - type = "jtagmkii"; - connection_type = usb; -; +# programmer +# id = "jtagmkII"; +# desc = "Atmel JTAG ICE mkII"; +# baudrate = 19200; # default is 19200 +# type = "jtagmkii"; +# connection_type = usb; +# ; -# easier to type -programmer parent "jtagmkII" - id = "jtag2slow"; -; +# # easier to type +# programmer parent "jtagmkII" +# id = "jtag2slow"; +# ; -# JTAG ICE mkII @ 115200 Bd -programmer parent "jtag2slow" - id = "jtag2fast"; - baudrate = 115200; -; +# # JTAG ICE mkII @ 115200 Bd +# programmer parent "jtag2slow" +# id = "jtag2fast"; +# baudrate = 115200; +# ; -# make the fast one the default, people will love that -programmer parent "jtag2fast" - id = "jtag2"; -; +# # make the fast one the default, people will love that +# programmer parent "jtag2fast" +# id = "jtag2"; +# ; -# JTAG ICE mkII in ISP mode -programmer - id = "jtag2isp"; - desc = "Atmel JTAG ICE mkII in ISP mode"; - baudrate = 115200; - type = "jtagmkii_isp"; - connection_type = usb; -; +# # JTAG ICE mkII in ISP mode +# programmer +# id = "jtag2isp"; +# desc = "Atmel JTAG ICE mkII in ISP mode"; +# baudrate = 115200; +# type = "jtagmkii_isp"; +# connection_type = usb; +# ; -# JTAG ICE mkII in debugWire mode -programmer - id = "jtag2dw"; - desc = "Atmel JTAG ICE mkII in debugWire mode"; - baudrate = 115200; - type = "jtagmkii_dw"; - connection_type = usb; -; +# # JTAG ICE mkII in debugWire mode +# programmer +# id = "jtag2dw"; +# desc = "Atmel JTAG ICE mkII in debugWire mode"; +# baudrate = 115200; +# type = "jtagmkii_dw"; +# connection_type = usb; +# ; -# JTAG ICE mkII in AVR32 mode -programmer - id = "jtagmkII_avr32"; - desc = "Atmel JTAG ICE mkII im AVR32 mode"; - baudrate = 115200; - type = "jtagmkii_avr32"; - connection_type = usb; -; +# # JTAG ICE mkII in AVR32 mode +# programmer +# id = "jtagmkII_avr32"; +# desc = "Atmel JTAG ICE mkII im AVR32 mode"; +# baudrate = 115200; +# type = "jtagmkii_avr32"; +# connection_type = usb; +# ; -# JTAG ICE mkII in AVR32 mode -programmer - id = "jtag2avr32"; - desc = "Atmel JTAG ICE mkII im AVR32 mode"; - baudrate = 115200; - type = "jtagmkii_avr32"; - connection_type = usb; -; +# # JTAG ICE mkII in AVR32 mode +# programmer +# id = "jtag2avr32"; +# desc = "Atmel JTAG ICE mkII im AVR32 mode"; +# baudrate = 115200; +# type = "jtagmkii_avr32"; +# connection_type = usb; +# ; -# JTAG ICE mkII in PDI mode -programmer - id = "jtag2pdi"; - desc = "Atmel JTAG ICE mkII PDI mode"; - baudrate = 115200; - type = "jtagmkii_pdi"; - connection_type = usb; -; +# # JTAG ICE mkII in PDI mode +# programmer +# id = "jtag2pdi"; +# desc = "Atmel JTAG ICE mkII PDI mode"; +# baudrate = 115200; +# type = "jtagmkii_pdi"; +# connection_type = usb; +# ; -# AVR Dragon in JTAG mode -programmer - id = "dragon_jtag"; - desc = "Atmel AVR Dragon in JTAG mode"; - baudrate = 115200; - type = "dragon_jtag"; - connection_type = usb; -; +# # AVR Dragon in JTAG mode +# programmer +# id = "dragon_jtag"; +# desc = "Atmel AVR Dragon in JTAG mode"; +# baudrate = 115200; +# type = "dragon_jtag"; +# connection_type = usb; +# ; -# AVR Dragon in ISP mode -programmer - id = "dragon_isp"; - desc = "Atmel AVR Dragon in ISP mode"; - baudrate = 115200; - type = "dragon_isp"; - connection_type = usb; -; +# # AVR Dragon in ISP mode +# programmer +# id = "dragon_isp"; +# desc = "Atmel AVR Dragon in ISP mode"; +# baudrate = 115200; +# type = "dragon_isp"; +# connection_type = usb; +# ; -# AVR Dragon in PP mode -programmer - id = "dragon_pp"; - desc = "Atmel AVR Dragon in PP mode"; - baudrate = 115200; - type = "dragon_pp"; - connection_type = usb; -; +# # AVR Dragon in PP mode +# programmer +# id = "dragon_pp"; +# desc = "Atmel AVR Dragon in PP mode"; +# baudrate = 115200; +# type = "dragon_pp"; +# connection_type = usb; +# ; -# AVR Dragon in HVSP mode -programmer - id = "dragon_hvsp"; - desc = "Atmel AVR Dragon in HVSP mode"; - baudrate = 115200; - type = "dragon_hvsp"; - connection_type = usb; -; +# # AVR Dragon in HVSP mode +# programmer +# id = "dragon_hvsp"; +# desc = "Atmel AVR Dragon in HVSP mode"; +# baudrate = 115200; +# type = "dragon_hvsp"; +# connection_type = usb; +# ; -# AVR Dragon in debugWire mode -programmer - id = "dragon_dw"; - desc = "Atmel AVR Dragon in debugWire mode"; - baudrate = 115200; - type = "dragon_dw"; - connection_type = usb; -; +# # AVR Dragon in debugWire mode +# programmer +# id = "dragon_dw"; +# desc = "Atmel AVR Dragon in debugWire mode"; +# baudrate = 115200; +# type = "dragon_dw"; +# connection_type = usb; +# ; -# AVR Dragon in PDI mode -programmer - id = "dragon_pdi"; - desc = "Atmel AVR Dragon in PDI mode"; - baudrate = 115200; - type = "dragon_pdi"; - connection_type = usb; -; +# # AVR Dragon in PDI mode +# programmer +# id = "dragon_pdi"; +# desc = "Atmel AVR Dragon in PDI mode"; +# baudrate = 115200; +# type = "dragon_pdi"; +# connection_type = usb; +# ; -programmer - id = "jtag3"; - desc = "Atmel AVR JTAGICE3 in JTAG mode"; - type = "jtagice3"; - connection_type = usb; - usbpid = 0x2110, 0x2140; -; +# programmer +# id = "jtag3"; +# desc = "Atmel AVR JTAGICE3 in JTAG mode"; +# type = "jtagice3"; +# connection_type = usb; +# usbpid = 0x2110, 0x2140; +# ; -programmer - id = "jtag3pdi"; - desc = "Atmel AVR JTAGICE3 in PDI mode"; - type = "jtagice3_pdi"; - connection_type = usb; - usbpid = 0x2110, 0x2140; -; +# programmer +# id = "jtag3pdi"; +# desc = "Atmel AVR JTAGICE3 in PDI mode"; +# type = "jtagice3_pdi"; +# connection_type = usb; +# usbpid = 0x2110, 0x2140; +# ; -programmer - id = "jtag3dw"; - desc = "Atmel AVR JTAGICE3 in debugWIRE mode"; - type = "jtagice3_dw"; - connection_type = usb; - usbpid = 0x2110, 0x2140; -; +# programmer +# id = "jtag3dw"; +# desc = "Atmel AVR JTAGICE3 in debugWIRE mode"; +# type = "jtagice3_dw"; +# connection_type = usb; +# usbpid = 0x2110, 0x2140; +# ; -programmer - id = "jtag3isp"; - desc = "Atmel AVR JTAGICE3 in ISP mode"; - type = "jtagice3_isp"; - connection_type = usb; - usbpid = 0x2110, 0x2140; -; +# programmer +# id = "jtag3isp"; +# desc = "Atmel AVR JTAGICE3 in ISP mode"; +# type = "jtagice3_isp"; +# connection_type = usb; +# usbpid = 0x2110, 0x2140; +# ; -programmer - id = "xplainedpro"; - desc = "Atmel AVR XplainedPro in JTAG mode"; - type = "jtagice3"; - connection_type = usb; - usbpid = 0x2111; -; +# programmer +# id = "xplainedpro"; +# desc = "Atmel AVR XplainedPro in JTAG mode"; +# type = "jtagice3"; +# connection_type = usb; +# usbpid = 0x2111; +# ; -programmer - id = "xplainedmini"; - desc = "Atmel AVR XplainedMini in ISP mode"; - type = "jtagice3_isp"; - connection_type = usb; - usbpid = 0x2145; -; +# programmer +# id = "xplainedmini"; +# desc = "Atmel AVR XplainedMini in ISP mode"; +# type = "jtagice3_isp"; +# connection_type = usb; +# usbpid = 0x2145; +# ; -programmer - id = "xplainedmini_dw"; - desc = "Atmel AVR XplainedMini in debugWIRE mode"; - type = "jtagice3_dw"; - connection_type = usb; - usbpid = 0x2145; -; +# programmer +# id = "xplainedmini_dw"; +# desc = "Atmel AVR XplainedMini in debugWIRE mode"; +# type = "jtagice3_dw"; +# connection_type = usb; +# usbpid = 0x2145; +# ; -programmer - id = "atmelice"; - desc = "Atmel-ICE (ARM/AVR) in JTAG mode"; - type = "jtagice3"; - connection_type = usb; - usbpid = 0x2141; -; +# programmer +# id = "atmelice"; +# desc = "Atmel-ICE (ARM/AVR) in JTAG mode"; +# type = "jtagice3"; +# connection_type = usb; +# usbpid = 0x2141; +# ; -programmer - id = "atmelice_pdi"; - desc = "Atmel-ICE (ARM/AVR) in PDI mode"; - type = "jtagice3_pdi"; - connection_type = usb; - usbpid = 0x2141; -; +# programmer +# id = "atmelice_pdi"; +# desc = "Atmel-ICE (ARM/AVR) in PDI mode"; +# type = "jtagice3_pdi"; +# connection_type = usb; +# usbpid = 0x2141; +# ; -programmer - id = "atmelice_dw"; - desc = "Atmel-ICE (ARM/AVR) in debugWIRE mode"; - type = "jtagice3_dw"; - connection_type = usb; - usbpid = 0x2141; -; +# programmer +# id = "atmelice_dw"; +# desc = "Atmel-ICE (ARM/AVR) in debugWIRE mode"; +# type = "jtagice3_dw"; +# connection_type = usb; +# usbpid = 0x2141; +# ; -programmer - id = "atmelice_isp"; - desc = "Atmel-ICE (ARM/AVR) in ISP mode"; - type = "jtagice3_isp"; - connection_type = usb; - usbpid = 0x2141; -; +# programmer +# id = "atmelice_isp"; +# desc = "Atmel-ICE (ARM/AVR) in ISP mode"; +# type = "jtagice3_isp"; +# connection_type = usb; +# usbpid = 0x2141; +# ; programmer @@ -1150,26 +1150,26 @@ programmer connection_type = serial; ; -programmer - id = "pickit2"; - desc = "MicroChip's PICkit2 Programmer"; - type = "pickit2"; - connection_type = usb; -; +# programmer +# id = "pickit2"; +# desc = "MicroChip's PICkit2 Programmer"; +# type = "pickit2"; +# connection_type = usb; +# ; -programmer - id = "flip1"; - desc = "FLIP USB DFU protocol version 1 (doc7618)"; - type = "flip1"; - connection_type = usb; -; +# programmer +# id = "flip1"; +# desc = "FLIP USB DFU protocol version 1 (doc7618)"; +# type = "flip1"; +# connection_type = usb; +# ; -programmer - id = "flip2"; - desc = "FLIP USB DFU protocol version 2 (AVR4023)"; - type = "flip2"; - connection_type = usb; -; +# programmer +# id = "flip2"; +# desc = "FLIP USB DFU protocol version 2 (AVR4023)"; +# type = "flip2"; +# connection_type = usb; +# ; # Parallel port programmers.