diff --git a/src/libslic3r/GCode/WipeTower.cpp b/src/libslic3r/GCode/WipeTower.cpp
index 6f09f034f..da4c6aa6e 100644
--- a/src/libslic3r/GCode/WipeTower.cpp
+++ b/src/libslic3r/GCode/WipeTower.cpp
@@ -947,11 +947,16 @@ void WipeTower::toolchange_Unload(
               .travel(old_x, writer.y()) // in case previous move was shortened to limit feedrate*/
               .resume_preview();
     }
-    if (new_temperature != 0 && (new_temperature != m_old_temperature || m_is_first_layer) ) { 	// Set the extruder temperature, but don't wait.
-        // If the required temperature is the same as last time, don't emit the M104 again (if user adjusted the value, it would be reset)
-        // However, always change temperatures on the first layer (this is to avoid issues with priming lines turned off).
-		writer.set_extruder_temp(new_temperature, false);
-        m_old_temperature = new_temperature;
+    // Wipe tower should only change temperature with single extruder MM. Otherwise, all temperatures should
+    // be already set and there is no need to change anything. Also, the temperature could be changed
+    // for wrong extruder.
+    if (m_semm) {
+        if (new_temperature != 0 && (new_temperature != m_old_temperature || m_is_first_layer) ) { 	// Set the extruder temperature, but don't wait.
+            // If the required temperature is the same as last time, don't emit the M104 again (if user adjusted the value, it would be reset)
+            // However, always change temperatures on the first layer (this is to avoid issues with priming lines turned off).
+            writer.set_extruder_temp(new_temperature, false);
+            m_old_temperature = new_temperature;
+        }
     }
 
     // Cooling:
@@ -1002,6 +1007,10 @@ void WipeTower::toolchange_Change(
     writer.append("[end_filament_gcode]\n");
     writer.append("[toolchange_gcode]\n");
 
+    // Travel to where we assume we are. Custom toolchange or some special T code handling (parking extruder etc)
+    // gcode could have left the extruder somewhere, we cannot just start extruding.
+    writer.append(std::string("G1 X") + std::to_string(writer.x()) +  " Y" + std::to_string(writer.y()) +  "\n");
+
     // The toolchange Tn command will be inserted later, only in case that the user does
     // not provide a custom toolchange gcode.
 	writer.set_tool(new_tool); // This outputs nothing, the writer just needs to know the tool has changed.
diff --git a/src/libslic3r/Print.cpp b/src/libslic3r/Print.cpp
index 71529cff1..796215781 100644
--- a/src/libslic3r/Print.cpp
+++ b/src/libslic3r/Print.cpp
@@ -1189,6 +1189,8 @@ std::string Print::validate() const
             return L("The Wipe Tower is currently only supported for the Marlin, RepRap/Sprinter and Repetier G-code flavors.");
         if (! m_config.use_relative_e_distances)
             return L("The Wipe Tower is currently only supported with the relative extruder addressing (use_relative_e_distances=1).");
+        if (m_config.ooze_prevention)
+            return L("Ooze prevention is currently not supported with the wipe tower enabled.");
         
         if (m_objects.size() > 1) {
             bool                                has_custom_layering = false;