Options on command line now override config. Also, "feed rate" was renamed to "speed" everywhere. #77

README.markdown

@@ -100,17 +100,17 @@ The author is Alessandro Ranellucci (me).
       Filament options:
         --filament-diameter Diameter in mm of your raw filament (default: 3)
         --extrusion-multiplier
-                            Change this to alter the amount of plastic extruded. There should be 
+                            Change this to alter the amount of plastic extruded. There should be
                             very little need to change this value, which is only useful to 
                             compensate for filament packing (default: 1)
         --temperature       Extrusion temperature, set 0 to disable (default: 200)
         
       Speed options:
-        --print-feed-rate   Speed of print moves in mm/sec (default: 60)
+        --travel-speed      Speed of non-print moves in mm/sec (default: 130)
-        --travel-feed-rate  Speed of non-print moves in mm/sec (default: 130)
+        --perimeter-speed   Speed of print moves for perimeters in mm/sec (default: 30)
-        --perimeter-feed-rate
+        --infill-speed      Speed of print moves in mm/sec (default: 60)
-                            Speed of print moves for perimeters in mm/sec (default: 60)
+        --solid-infill-speed Speed of print moves for solid surfaces in mm/sec (default: 60)
-        --bridge-feed-rate  Speed of bridge print moves in mm/sec (default: 60)
+        --bridge-speed      Speed of bridge print moves in mm/sec (default: 60)
         --bottom-layer-speed-ratio
                             Factor to increase/decrease speeds on bottom 
                             layer by (default: 0.3)

lib/Slic3r.pm

@@ -48,11 +48,11 @@ our $extrusion_multiplier = 1;
 our $temperature        = 200;
 
 # speed options
-our $travel_feed_rate           = 130;  # mm/sec
+our $travel_speed           = 130;  # mm/sec
-our $perimeter_feed_rate        = 30;   # mm/sec
+our $perimeter_speed        = 30;   # mm/sec
-our $infill_feed_rate           = 60;   # mm/sec
+our $infill_speed           = 60;   # mm/sec
-our $solid_infill_feed_rate     = 60;   # mm/sec
+our $solid_infill_speed     = 60;   # mm/sec
-our $bridge_feed_rate           = 60;   # mm/sec
+our $bridge_speed           = 60;   # mm/sec
 our $bottom_layer_speed_ratio   = 0.3;
 
 # accuracy options

lib/Slic3r/Config.pm

@@ -10,119 +10,158 @@ our $Options = {
     # printer options
     'nozzle_diameter' => {
         label   => 'Nozzle diameter',
+        cli     => 'nozzle-diameter=f',
         type    => 'f',
     },
     'print_center' => {
         label   => 'Print center',
+        cli     => 'print-center=s',
         type    => 'point',
         serialize   => sub { join ',', @{$_[0]} },
         deserialize => sub { [ split /,/, $_[0] ] },
     },
     'use_relative_e_distances' => {
         label   => 'Use relative E distances',
+        cli     => 'use-relative-e-distances',
         type    => 'bool',
     },
     'no_extrusion' => {
         label   => 'No extrusion',
+        cli     => 'no-extrusion',
         type    => 'bool',
     },
     'z_offset' => {
         label   => 'Z offset',
+        cli     => 'z-offset=f',
         type    => 'f',
     },
+    'gcode_arcs' => {
+        label   => 'Use native GCODE arcs',
+        cli     => 'gcode-arcs',
+        type    => 'bool',
+    },
+    'g0' => {
+        label   => 'Use g0 for travel moves',
+        cli     => 'g0',
+        type    => 'bool',
+    },
     
     # filament options
     'filament_diameter' => {
         label   => 'Diameter (mm)',
+        cli     => 'filament-diameter=f',
         type    => 'f',
     },
     'extrusion_multiplier' => {
         label   => 'Extrusion multiplier',
+        cli     => 'extrusion-multiplier=f',
         type    => 'f',
         aliases => [qw(filament_packing_density)],
     },
     'temperature' => {
         label   => 'Temperature (°C)',
+        cli     => 'temperature=i',
         type    => 'i',
     },
     
     # speed options
-    'travel_feed_rate' => {
+    'travel_speed' => {
         label   => 'Travel (mm/s)',
+        cli     => 'travel-speed=i',
         type    => 'f',
+        aliases => [qw(travel_feed_rate)],
     },
-    'perimeter_feed_rate' => {
+    'perimeter_speed' => {
         label   => 'Perimeters (mm/s)',
+        cli     => 'perimeter-speed=i',
         type    => 'f',
+        aliases => [qw(perimeter_feed_rate)],
     },
-    'infill_feed_rate' => {
+    'infill_speed' => {
         label   => 'Infill (mm/s)',
+        cli     => 'infill-speed=i',
         type    => 'f',
-        aliases => [qw(print_feed_rate)],
+        aliases => [qw(print_feed_rate infill_feed_rate)],
     },
-    'solid_infill_feed_rate' => {
+    'solid_infill_speed' => {
         label   => 'Solid infill (mm/s)',
+        cli     => 'solid-infill-speed=i',
         type    => 'f',
+        aliases => [qw(solid_infill_feed_rate)],
     },
-    'bridge_feed_rate' => {
+    'bridge_speed' => {
         label   => 'Bridges (mm/s)',
+        cli     => 'bridge-speed=i',
         type    => 'f',
+        aliases => [qw(bridge_feed_rate)],
     },
     'bottom_layer_speed_ratio' => {
         label   => 'Bottom layer speed ratio',
+        cli     => 'bottom-layer-speed-ratio=f',
         type    => 'f',
     },
     
     # accuracy options
     'layer_height' => {
         label   => 'Layer height (mm)',
+        cli     => 'layer-height=f',
         type    => 'f',
     },
     'extrusion_width_ratio' => {
         label   => 'Extrusion width (ratio over layer height; leave zero to calculate automatically)',
+        cli     => 'extrusion-width-ratio=f',
         type    => 'f',
     },
     'first_layer_height_ratio' => {
         label   => 'First layer height ratio',
+        cli     => 'first-layer-height-ratio=f',
         type    => 'f',
     },
     'infill_every_layers' => {
         label   => 'Infill every N layers',
+        cli     => 'infill-every-layers=i',
         type    => 'i',
     },
     
     # print options
     'perimeters' => {
         label   => 'Perimeters',
+        cli     => 'perimeters=i',
         type    => 'i',
         aliases => [qw(perimeter_offsets)],
     },
     'solid_layers' => {
         label   => 'Solid layers',
+        cli     => 'solid-layers=i',
         type    => 'i',
     },
     'fill_pattern' => {
         label   => 'Fill pattern',
+        cli     => 'fill-pattern=s',
         type    => 'select',
         values  => [qw(rectilinear line concentric hilbertcurve archimedeanchords octagramspiral)],
         labels  => [qw(rectilinear line concentric), 'hilbertcurve (slow)', 'archimedeanchords (slow)', 'octagramspiral (slow)'],
     },
     'solid_fill_pattern' => {
         label   => 'Solid fill pattern',
+        cli     => 'solid-fill-pattern=s',
         type    => 'select',
         values  => [qw(rectilinear concentric hilbertcurve archimedeanchords octagramspiral)],
         labels  => [qw(rectilinear concentric), 'hilbertcurve (slow)', 'archimedeanchords (slow)', 'octagramspiral (slow)'],
     },
     'fill_density' => {
         label   => 'Fill density',
+        cli     => 'fill-density=f',
         type    => 'f',
     },
     'fill_angle' => {
         label   => 'Fill angle (°)',
+        cli     => 'fill-angle=i',
         type    => 'i',
     },
     'start_gcode' => {
         label   => 'Start GCODE',
+        cli     => 'start-gcode=s',
         type    => 's',
         multiline => 1,
         width   => 350,
@@ -132,6 +171,7 @@ our $Options = {
     },
     'end_gcode' => {
         label   => 'End GCODE',
+        cli     => 'end-gcode=s',
         type    => 's',
         multiline => 1,
         width   => 350,
@@ -143,60 +183,73 @@ our $Options = {
     # retraction options
     'retract_length' => {
         label   => 'Length (mm)',
+        cli     => 'retract-length=f',
         type    => 'f',
     },
     'retract_speed' => {
         label   => 'Speed (mm/s)',
+        cli     => 'retract-speed=i',
         type    => 'i',
     },
     'retract_restart_extra' => {
         label   => 'Extra length on restart (mm)',
+        cli     => 'retract-restart-extra=f',
         type    => 'f',
     },
     'retract_before_travel' => {
         label   => 'Minimum travel after retraction (mm)',
+        cli     => 'retract-before-travel=f',
         type    => 'f',
     },
     'retract_lift' => {
         label   => 'Lift Z (mm)',
+        cli     => 'retract-lift=f',
         type    => 'f',
     },
     
     # skirt options
     'skirts' => {
         label   => 'Loops',
+        cli     => 'skirts=i',
         type    => 'i',
     },
     'skirt_distance' => {
         label   => 'Distance from object (mm)',
+        cli     => 'skirt-distance=i',
         type    => 'i',
     },
     'skirt_height' => {
         label   => 'Skirt height (layers)',
+        cli     => 'skirt-height=i',
         type    => 'i',
     },
     
     # transform options
     'scale' => {
         label   => 'Scale',
+        cli     => 'scale=f',
         type    => 'f',
     },
     'rotate' => {
         label   => 'Rotate (°)',
+        cli     => 'rotate=i',
         type    => 'i',
     },
     'duplicate_x' => {
         label   => 'Copies along X',
+        cli     => 'duplicate-x=i',
         type    => 'i',
         aliases => [qw(multiply_x)],
     },
     'duplicate_y' => {
         label   => 'Copies along Y',
+        cli     => 'duplicate-y=i',
         type    => 'i',
         aliases => [qw(multiply_y)],
     },
     'duplicate_distance' => {
         label   => 'Distance between copies',
+        cli     => 'duplicate-distance=i',
         type    => 'i',
         aliases => [qw(multiply_distance)],
     },
@@ -260,7 +313,7 @@ sub validate_cli {
                 die "Invalid value for --${_}-gcode: file does not exist"
                     if !-e $opt->{$_."_gcode"};
                 open my $fh, "<", $opt->{$_."_gcode"};
-                set($_."_gcode", do { local $/; <$fh> });
+                $opt->{$_."_gcode"} = do { local $/; <$fh> };
                 close $fh;
             }
         }
@@ -361,8 +414,8 @@ sub validate {
         if $Slic3r::skirt_height < 1;
     
     # legacy with existing config files
-    $Slic3r::bridge_feed_rate ||= $Slic3r::infill_feed_rate;
+    $Slic3r::bridge_speed ||= $Slic3r::infill_speed;
-    $Slic3r::solid_infill_feed_rate ||= $Slic3r::infill_feed_rate;
+    $Slic3r::solid_infill_speed ||= $Slic3r::infill_speed;
 }
 
 1;

lib/Slic3r/Extruder.pm

@@ -16,25 +16,25 @@ has 'last_f'             => (is => 'rw', default => sub {0});
 has 'dec'                => (is => 'ro', default => sub { 3 } );
 
 # calculate speeds
-has 'travel_feed_rate' => (
+has 'travel_speed' => (
     is      => 'ro',
-    default => sub { $Slic3r::travel_feed_rate * 60 },  # mm/min
+    default => sub { $Slic3r::travel_speed * 60 },  # mm/min
 );
-has 'perimeter_feed_rate' => (
+has 'perimeter_speed' => (
     is      => 'ro',
-    default => sub { $Slic3r::perimeter_feed_rate * 60 },  # mm/min
+    default => sub { $Slic3r::perimeter_speed * 60 },  # mm/min
 );
-has 'infill_feed_rate' => (
+has 'infill_speed' => (
     is      => 'ro',
-    default => sub { $Slic3r::infill_feed_rate * 60 },  # mm/min
+    default => sub { $Slic3r::infill_speed * 60 },  # mm/min
 );
-has 'solid_infill_feed_rate' => (
+has 'solid_infill_speed' => (
     is      => 'ro',
-    default => sub { $Slic3r::solid_infill_feed_rate * 60 },  # mm/min
+    default => sub { $Slic3r::solid_infill_speed * 60 },  # mm/min
 );
-has 'bridge_feed_rate' => (
+has 'bridge_speed' => (
     is      => 'ro',
-    default => sub { $Slic3r::bridge_feed_rate * 60 },  # mm/min
+    default => sub { $Slic3r::bridge_speed * 60 },  # mm/min
 );
 has 'retract_speed' => (
     is      => 'ro',
@@ -122,10 +122,10 @@ sub extrude {
     
     # extrude arc or line
     $self->print_feed_rate(
-        $path->role =~ /^(perimeter|skirt)$/o   ? $self->perimeter_feed_rate
+        $path->role =~ /^(perimeter|skirt)$/o   ? $self->perimeter_speed
-            : $path->role eq 'fill'             ? $self->infill_feed_rate
+            : $path->role eq 'fill'             ? $self->infill_speed
-            : $path->role eq 'solid-fill'       ? $self->solid_infill_feed_rate
+            : $path->role eq 'solid-fill'       ? $self->solid_infill_speed
-            : $path->role eq 'bridge'           ? $self->bridge_feed_rate
+            : $path->role eq 'bridge'           ? $self->bridge_speed
             : die "Unknown role: " . $path->role
     );
     if ($path->isa('Slic3r::ExtrusionPath::Arc')) {
@@ -268,7 +268,7 @@ sub _Gx {
         : 1;
     
     # determine speed
-    my $speed = ($e ? $self->print_feed_rate : $self->travel_feed_rate) * $speed_multiplier;
+    my $speed = ($e ? $self->print_feed_rate : $self->travel_speed) * $speed_multiplier;
     
     # output speed if it's different from last one used
     # (goal: reduce gcode size)

lib/Slic3r/GUI/SkeinPanel.pm

@@ -25,11 +25,11 @@ sub new {
         },
         print_speed => {
             title => 'Print speed',
-            options => [qw(perimeter_feed_rate infill_feed_rate solid_infill_feed_rate bridge_feed_rate)],
+            options => [qw(perimeter_speed infill_speed solid_infill_speed bridge_speed)],
         },
         speed => {
             title => 'Other speed settings',
-            options => [qw(travel_feed_rate bottom_layer_speed_ratio)],
+            options => [qw(travel_speed bottom_layer_speed_ratio)],
         },
         accuracy => {
             title => 'Accuracy',

slic3r.pl

@@ -11,76 +11,29 @@ BEGIN {
 use Getopt::Long;
 use Slic3r;
 use XXX;
-
 $|++;
-our %opt;
-GetOptions(
-    'help'                  => sub { usage() },
 
-    'debug'                 => \$Slic3r::debug,
+my %opt = ();
-    'o|output=s'            => \$opt{output},
+my %cli_options = ();
-    'close-after-slicing'   => \$opt{close_after_slicing},
+{
+    my %options = (
+        'help'                  => sub { usage() },
+        
+        'debug'                 => \$Slic3r::debug,
+        'o|output=s'            => \$opt{output},
+        'close-after-slicing'   => \$opt{close_after_slicing},
+        
+        'save=s'                => \$opt{save},
+        'load=s'                => \$opt{load},
+    );
+    foreach my $opt_key (keys %$Slic3r::Config::Options) {
+        my $opt = $Slic3r::Config::Options->{$opt_key};
+        $options{ $opt->{cli} } = \$cli_options{$opt_key}
+            if $opt->{cli};
+    }
     
-    'save=s'                    => \$opt{save},
+    GetOptions(%options) or usage(1);
-    'load=s'                    => \$opt{load},
+}
-    
-    # printer options
-    'nozzle-diameter=f'         => \$Slic3r::nozzle_diameter,
-    'print-center=s'            => \$Slic3r::print_center,
-    'use-relative-e-distances'  => \$Slic3r::use_relative_e_distances,
-    'no-extrusion'              => \$Slic3r::no_extrusion,
-    'z-offset=f'                => \$Slic3r::z_offset,
-    'gcode-arcs'                => \$Slic3r::gcode_arcs,
-    'g0'                        => \$Slic3r::g0,
-    
-    # filament options
-    'filament-diameter=f'           => \$Slic3r::filament_diameter,
-    'extrusion-multiplier=f'        => \$Slic3r::extrusion_multiplier,
-    'temperature=i'                 => \$Slic3r::temperature,
-    
-    # speed options
-    'travel-feed-rate=i'            => \$Slic3r::travel_feed_rate,
-    'perimeter-feed-rate=i'         => \$Slic3r::perimeter_feed_rate,
-    'infill-feed-rate=i'            => \$Slic3r::infill_feed_rate,
-    'solid-infill-feed-rate=i'      => \$Slic3r::solid_infill_feed_rate,
-    'bridge-feed-rate=i'            => \$Slic3r::bridge_feed_rate,
-    'bottom-layer-speed-ratio=f'    => \$Slic3r::bottom_layer_speed_ratio,
-    
-    # accuracy options
-    'layer-height=f'                => \$Slic3r::layer_height,
-    'extrusion-width-ratio=f'       => \$Slic3r::extrusion_width_ratio,
-    'first-layer-height-ratio=f'    => \$Slic3r::first_layer_height_ratio,
-    'infill-every-layers=i'         => \$Slic3r::infill_every_layers,
-    
-    # print options
-    'perimeters=i'          => \$Slic3r::perimeters,
-    'solid-layers=i'        => \$Slic3r::solid_layers,
-    'fill-pattern=s'        => \$Slic3r::fill_pattern,
-    'solid-fill-pattern=s'  => \$Slic3r::solid_fill_pattern,
-    'fill-density=f'        => \$Slic3r::fill_density,
-    'fill-angle=i'          => \$Slic3r::fill_angle,
-    'start-gcode=s'         => \$opt{start_gcode},
-    'end-gcode=s'           => \$opt{end_gcode},
-    
-    # retraction options
-    'retract-length=f'          => \$Slic3r::retract_length,
-    'retract-speed=i'           => \$Slic3r::retract_speed,
-    'retract-restart-extra=f'   => \$Slic3r::retract_restart_extra,
-    'retract-before-travel=f'   => \$Slic3r::retract_before_travel,
-    'retract-lift=f'            => \$Slic3r::retract_lift,
-    
-    # skirt options
-    'skirts=i'              => \$Slic3r::skirts,
-    'skirt-distance=i'      => \$Slic3r::skirt_distance,
-    'skirt-height=i'        => \$Slic3r::skirt_height,
-    
-    # transform options
-    'scale=f'               => \$Slic3r::scale,
-    'rotate=i'              => \$Slic3r::rotate,
-    'duplicate-x=i'         => \$Slic3r::duplicate_x,
-    'duplicate-y=i'         => \$Slic3r::duplicate_y,
-    'duplicate-distance=i'  => \$Slic3r::duplicate_distance,
-) or usage(1);
 
 # load configuration
 if ($opt{load}) {
@@ -89,7 +42,11 @@ if ($opt{load}) {
 }
 
 # validate command line options
-Slic3r::Config->validate_cli(\%opt);
+Slic3r::Config->validate_cli(\%cli_options);
+
+# apply command line options
+Slic3r::Config->set($_ => $cli_options{$_})
+    for grep defined $cli_options{$_}, keys %cli_options;
 
 # validate configuration
 Slic3r::Config->validate;
@@ -155,13 +112,11 @@ Usage: slic3r.pl [ OPTIONS ] file.stl
     --temperature       Extrusion temperature, set 0 to disable (default: $Slic3r::temperature)
     
   Speed options:
-    --travel-feed-rate  Speed of non-print moves in mm/sec (default: $Slic3r::travel_feed_rate)
+    --travel-speed      Speed of non-print moves in mm/sec (default: $Slic3r::travel_speed)
-    --perimeter-feed-rate
+    --perimeter-speed   Speed of print moves for perimeters in mm/sec (default: $Slic3r::perimeter_speed)
-                        Speed of print moves for perimeters in mm/sec (default: $Slic3r::perimeter_feed_rate)
+    --infill-speed      Speed of print moves in mm/sec (default: $Slic3r::infill_speed)
-    --infill-feed-rate  Speed of print moves in mm/sec (default: $Slic3r::infill_feed_rate)
+    --solid-infill-speed Speed of print moves for solid surfaces in mm/sec (default: $Slic3r::solid_infill_speed)
-    --solid-infill-feed-rate
+    --bridge-speed      Speed of bridge print moves in mm/sec (default: $Slic3r::bridge_speed)
-                        Speed of print moves for solid surfaces in mm/sec (default: $Slic3r::solid_infill_feed_rate)
-    --bridge-feed-rate  Speed of bridge print moves in mm/sec (default: $Slic3r::bridge_feed_rate)
     --bottom-layer-speed-ratio
                         Factor to increase/decrease speeds on bottom 
                         layer by (default: $Slic3r::bottom_layer_speed_ratio)