bubnikv
41f50b246c
Inlined Surface::any_internal_contains / any_bottom_contains
2017-07-10 13:15:36 +02:00
bubnikv
ed2ee2f6f3
Merged support_fills with support_interface_fills.
...
When extruding supports, the support is interleaved with interface
if possible (when extruded with the same extruder).
Otherwise the base is extruded first.
2017-04-07 17:37:30 +02:00
bubnikv
39679f9518
Missed this one at the last check-in.
2016-11-20 12:59:29 +01:00
bubnikv
79f5a16536
Reverted the perimeter generator to not save the perimeter areas.
...
These could be calculated from the fill areas if needed.
On the other side, the non-classified (non-split) fill areas are stored
now for use in the "ensure vertical wall thickness" feature,
also the non-split fill areas are re-used when recalculating the infills.
This is safer than trying to stitch the fill region together from the
classified fragments.
Modified the "ensure vertical wall thickness" feature to use the non-split
fill areas instead of perimeter areas for the calculation
of non-supported regions. This is cheaper as the fill areas contain
roughly half the edges.
2016-11-17 23:22:59 +01:00
bubnikv
95ede7c4b8
Rewrote Fill2.pm to C++, deleted Perl infills for good.
...
Removed dependency on Perl Math::PlanePath module.
Fixed compilation with Visual Studio and SLIC3R_DEBUG: Visual Studio older than 2015 does not support the prinf type specifier %zu. Use %Iu instead.
C++11 move semantics enabled.
2016-11-02 10:47:00 +01:00
bubnikv
e0d1aa8a1a
Collect the perimeter surfaces when generating perimeters.
...
The perimeter surfaces are later used for performing infill
below overhangs and to maintan configured vertical wall thickness
at sloping surfaces.
2016-09-26 13:44:23 +02:00
Alessandro Ranellucci
4913e90e10
Remove any Perl related code from libslic3r
2015-12-08 00:39:54 +01:00
Alessandro Ranellucci
4f8a18bbad
Ported Layer::maker_perimeters() to XS
2015-12-02 19:32:57 +01:00
Alessandro Ranellucci
9fcec10737
Finished porting LayerRegion to C++
2015-10-26 23:24:46 +01:00
Alessandro Ranellucci
6ac79e3ed6
Ported make_perimeters() to C++
2015-07-23 16:27:21 +02:00
Alessandro Ranellucci
3e739b87da
Finished porting Slic3r::GCode to XS (speed boost!)
2015-07-02 20:24:16 +02:00
Alessandro Ranellucci
801f629fdc
Ported Slic3r::GCode storage to XS
2015-07-01 21:47:17 +02:00
Alessandro Ranellucci
be2f46ca68
Ported Layer::merge_slices() to XS
2015-04-16 20:44:55 +02:00
Alessandro Ranellucci
bb3bf28e59
Ported prepare_fill_surfaces() to XS/C++
2015-02-01 12:43:58 +01:00
Alessandro Ranellucci
8791f5a493
Cleanup of some method signatures and of XS return types
2015-01-19 18:53:04 +01:00
Alessandro Ranellucci
9f0283f808
Minor issue when dealing with files with empty layers at bottom. #2553
2015-01-18 12:35:05 +01:00
Alessandro Ranellucci
2562070232
Refactored the travel/retract/avoid_crossing_perimeters logic. Several edge cases are now handled correctly. #2498
2015-01-06 14:52:03 +01:00
Alessandro Ranellucci
7e82159620
Fixed one more case where only_retract_when_crossing_perimeters didn't apply. #2498
2015-01-06 11:29:34 +01:00
Alessandro Ranellucci
5a0f4eac8d
One more retraction optimization
2014-12-25 11:37:54 +01:00
Alessandro Ranellucci
93507bfd49
Bugfix: only_retract_when_crossing_perimeters was not correctly applied on bottom layer when no bottom solid layers were printed
2014-12-22 11:46:16 +01:00
Alessandro Ranellucci
c8596c5c58
Limit "Only retract when crossing perimeters" so that retraction is triggered also when crossing the boundaries of a single region. #2298
2014-12-09 01:08:58 +01:00
Alessandro Ranellucci
5deadc8f12
Refactoring: removed _islands members in Slic3r::GCode
2014-11-23 20:03:16 +01:00
Alessandro Ranellucci
b69caff93c
Ported LayerRegion::make_slices() to XS
2014-11-09 16:24:07 +01:00
Alessandro Ranellucci
6adc3477c9
Moved C++ code into new libslic3r directory
2014-08-03 19:42:29 +02:00
Alessandro Ranellucci
7ff13c063f
Port PrintRegion::flow() and LayerRegion.flow() to XS
2014-08-03 19:17:23 +02:00
Alessandro Ranellucci
380dd8adfc
Ported some methods to XS
2014-08-03 18:41:09 +02:00
Alessandro Ranellucci
5c54acf9ac
Use ->ptr() for CoolingBuffer too
2014-06-10 16:17:34 +02:00
Y. Sapir
07dd799967
Fix inherited Layer::Support id and object accessors.
2014-05-25 00:50:49 +03:00
Y. Sapir
b8b8c746d9
Make clear_regions and delete_region methods private (both Print & Layer), and remove from XSP.
2014-05-25 00:11:17 +03:00
Y. Sapir
22b05cb187
Make read-only constructor parameters - private.
2014-05-24 23:50:45 +03:00
Y. Sapir
8da0bded1d
Move Print object storage to C++. (along with its subobjects)
2014-05-24 23:50:29 +03:00
