# Copyright (C) 2018 THE Slic3rPE'S COPYRIGHT HOLDER # This file is distributed under the same license as the Slic3rPE package. # Oleksandra Iushchenko , 2018. # msgid "" msgstr "" "Project-Id-Version: SLIC3R PE VERSION\n" "Report-Msgid-Bugs-To: \n" "POT-Creation-Date: 2018-02-13 17:18+0100\n" "PO-Revision-Date: 2018-02-15 18:17+0100\n" "Last-Translator: Oleksandra Iushchenko \n" "Language-Team: \n" "MIME-Version: 1.0\n" "Content-Type: text/plain; charset=UTF-8\n" "Content-Transfer-Encoding: 8bit\n" "X-Generator: Poedit 2.0.6\n" "Plural-Forms: nplurals=2; plural=(n != 1);\n" "Language: en_US\n" "X-Poedit-KeywordsList: _L\n" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:50 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1188 msgid "Size" msgstr "Size" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:51 msgid "Size in X and Y of the rectangular plate." msgstr "Size in X and Y of the rectangular plate." #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:57 msgid "Origin" msgstr "Origin" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:58 msgid "" "Distance of the 0,0 G-code coordinate from the front left corner of the " "rectangle." msgstr "" "Distance of the 0,0 G-code coordinate from the front left corner of the " "rectangle." #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:65 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:133 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:204 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:215 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:329 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:340 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:359 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:438 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:783 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:803 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:862 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:880 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:898 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1046 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1054 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1096 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1105 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1115 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1123 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1131 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1217 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1423 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1493 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1529 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1706 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1713 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1720 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1729 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1739 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1749 msgid "mm" msgstr "mm" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:66 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:435 msgid "Diameter" msgstr "Diameter" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:67 msgid "" "Diameter of the print bed. It is assumed that origin (0,0) is located in the " "center." msgstr "" "Diameter of the print bed. It is assumed that origin (0,0) is located in the " "center." #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:965 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:312 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:704 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:960 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1274 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1447 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1473 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:432 msgid "Extruders" msgstr "Extruders" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:966 msgid "Number of extruders of the printer." msgstr "Number of extruders of the printer." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:30 msgid "Avoid crossing perimeters" msgstr "Avoid crossing perimeters" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:31 msgid "" "Optimize travel moves in order to minimize the crossing of perimeters. This " "is mostly useful with Bowden extruders which suffer from oozing. This " "feature slows down both the print and the G-code generation." msgstr "" "Optimize travel moves in order to minimize the crossing of perimeters. This " "is mostly useful with Bowden extruders which suffer from oozing. This " "feature slows down both the print and the G-code generation." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:38 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:939 msgid "Bed shape" msgstr "Bed shape" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:42 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1574 msgid "Other layers" msgstr "Other layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:43 msgid "" "Bed temperature for layers after the first one. Set this to zero to disable " "bed temperature control commands in the output." msgstr "" "Bed temperature for layers after the first one. Set this to zero to disable " "bed temperature control commands in the output." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:46 msgid "Bed temperature" msgstr "Bed temperature" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:52 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1131 msgid "Before layer change G-code" msgstr "Before layer change G-code" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:53 msgid "" "This custom code is inserted at every layer change, right before the Z move. " "Note that you can use placeholder variables for all Slic3r settings as well " "as [layer_num] and [layer_z]." msgstr "" "This custom code is inserted at every layer change, right before the Z move. " "Note that you can use placeholder variables for all Slic3r settings as well " "as [layer_num] and [layer_z]." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:63 msgid "Between objects G-code" msgstr "Between objects G-code" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:64 msgid "" "This code is inserted between objects when using sequential printing. By " "default extruder and bed temperature are reset using non-wait command; " "however if M104, M109, M140 or M190 are detected in this custom code, Slic3r " "will not add temperature commands. Note that you can use placeholder " "variables for all Slic3r settings, so you can put a \"M109 " "S[first_layer_temperature]\" command wherever you want." msgstr "" "This code is inserted between objects when using sequential printing. By " "default extruder and bed temperature are reset using non-wait command; " "however if M104, M109, M140 or M190 are detected in this custom code, Slic3r " "will not add temperature commands. Note that you can use placeholder " "variables for all Slic3r settings, so you can put a \"M109 " "S[first_layer_temperature]\" command wherever you want." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:72 msgid "Bottom" msgstr "Bottom" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:73 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:243 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:294 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:302 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:606 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:764 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:780 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:943 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:991 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1154 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1585 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1641 msgid "Layers and Perimeters" msgstr "Layers and perimeters" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:74 msgid "Number of solid layers to generate on bottom surfaces." msgstr "Number of solid layers to generate on bottom surfaces." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:76 msgid "Bottom solid layers" msgstr "Bottom solid layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:81 msgid "Bridge" msgstr "Bridge" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:82 msgid "" "This is the acceleration your printer will use for bridges. Set zero to " "disable acceleration control for bridges." msgstr "" "This is the acceleration your printer will use for bridges. Set zero to " "disable acceleration control for bridges." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:84 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:178 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:578 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:686 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:954 msgid "mm/s\\u00B2" msgstr "mm/s\\u00B2" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:90 msgid "Bridging angle" msgstr "Bridging angle" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:91 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:251 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:492 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:506 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:544 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:683 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:693 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:711 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:729 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:748 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1265 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1282 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:347 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:348 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:664 msgid "Infill" msgstr "Infill" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:92 msgid "" "Bridging angle override. If left to zero, the bridging angle will be " "calculated automatically. Otherwise the provided angle will be used for all " "bridges. Use 180\\u00B0 for zero angle." msgstr "" "Bridging angle override. If left to zero, the bridging angle will be " "calculated automatically. Otherwise the provided angle will be used for all " "bridges. Use 180\\u00B0 for zero angle." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:95 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:496 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1172 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1183 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1403 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1559 msgid "\\u00B0" msgstr "\\u00B0" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:101 msgid "Bridges fan speed" msgstr "Bridges fan speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:102 msgid "This fan speed is enforced during all bridges and overhangs." msgstr "This fan speed is enforced during all bridges and overhangs." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:103 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:508 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:791 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:852 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1062 msgid "%" msgstr "%" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:110 msgid "Bridge flow ratio" msgstr "Bridge flow ratio" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:111 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:212 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:738 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1735 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:343 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:357 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:450 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:453 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:830 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1112 msgid "Advanced" msgstr "Advanced" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:112 msgid "" "This factor affects the amount of plastic for bridging. You can decrease it " "slightly to pull the extrudates and prevent sagging, although default " "settings are usually good and you should experiment with cooling (use a fan) " "before tweaking this." msgstr "" "This factor affects the amount of plastic for bridging. You can decrease it " "slightly to pull the extrudates and prevent sagging, although default " "settings are usually good and you should experiment with cooling (use a fan) " "before tweaking this." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:121 msgid "Bridges" msgstr "Bridges" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:122 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:282 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:637 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:749 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:981 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1203 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1253 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1304 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1627 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:399 msgid "Speed" msgstr "Speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:123 msgid "Speed for printing bridges." msgstr "Speed for printing bridges." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:124 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:640 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:751 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:813 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:870 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:983 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1139 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1148 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1538 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1651 msgid "mm/s" msgstr "mm/s" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:131 msgid "Brim width" msgstr "Brim width" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:132 msgid "" "Horizontal width of the brim that will be printed around each object on the " "first layer." msgstr "" "Horizontal width of the brim that will be printed around each object on the " "first layer." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:139 msgid "Clip multi-part objects" msgstr "Clip multi-part objects" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:140 msgid "" "When printing multi-material objects, this settings will make slic3r to clip " "the overlapping object parts one by the other (2nd part will be clipped by " "the 1st, 3rd part will be clipped by the 1st and 2nd etc)." msgstr "" "When printing multi-material objects, this settings will make slic3r to clip " "the overlapping object parts one by the other (2nd part will be clipped by " "the 1st, 3rd part will be clipped by the 1st and 2nd etc)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:147 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:510 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:868 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1673 msgid "Compatible printers" msgstr "Compatible printers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:151 msgid "Compatible printers condition" msgstr "Compatible printers condition" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:152 msgid "" "A boolean expression using the configuration values of an active printer " "profile. If this expression evaluates to true, this profile is considered " "compatible with the active printer profile." msgstr "" "A boolean expression using the configuration values of an active printer " "profile. If this expression evaluates to true, this profile is considered " "compatible with the active printer profile." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:158 msgid "Complete individual objects" msgstr "Complete individual objects" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:159 msgid "" "When printing multiple objects or copies, this feature will complete each " "object before moving onto next one (and starting it from its bottom layer). " "This feature is useful to avoid the risk of ruined prints. Slic3r should " "warn and prevent you from extruder collisions, but beware." msgstr "" "When printing multiple objects or copies, this feature will complete each " "object before moving onto next one (and starting it from its bottom layer). " "This feature is useful to avoid the risk of ruined prints. Slic3r should " "warn and prevent you from extruder collisions, but beware." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:167 msgid "Enable auto cooling" msgstr "Enable auto cooling" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:168 msgid "" "This flag enables the automatic cooling logic that adjusts print speed and " "fan speed according to layer printing time." msgstr "" "This flag enables the automatic cooling logic that adjusts print speed and " "fan speed according to layer printing time." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:174 #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:293 msgid "Default" msgstr "Default" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:175 msgid "" "This is the acceleration your printer will be reset to after the role-" "specific acceleration values are used (perimeter/infill). Set zero to " "prevent resetting acceleration at all." msgstr "" "This is the acceleration your printer will be reset to after the role-" "specific acceleration values are used (perimeter/infill). Set zero to " "prevent resetting acceleration at all." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:184 msgid "Disable fan for the first" msgstr "Disable fan for the first" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:185 msgid "" "You can set this to a positive value to disable fan at all during the first " "layers, so that it does not make adhesion worse." msgstr "" "You can set this to a positive value to disable fan at all during the first " "layers, so that it does not make adhesion worse." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:187 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:696 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1035 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1226 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1287 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1439 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1484 msgid "layers" msgstr "layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:194 msgid "Don't support bridges" msgstr "Don't support bridges" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:195 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1032 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1382 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1389 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1401 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1411 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1419 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1434 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1455 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1466 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1482 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1491 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1500 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1511 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1527 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1535 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1536 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1545 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1553 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1567 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:375 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:376 msgid "Support material" msgstr "Support material" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:196 msgid "" "Experimental option for preventing support material from being generated " "under bridged areas." msgstr "" "Experimental option for preventing support material from being generated " "under bridged areas." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:202 msgid "Distance between copies" msgstr "Distance between copies" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:203 msgid "Distance used for the auto-arrange feature of the plater." msgstr "Distance used for the auto-arrange feature of the plater." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:211 msgid "Elefant foot compensation" msgstr "Elefant foot compensation" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:213 msgid "" "The first layer will be shrunk in the XY plane by the configured value to " "compensate for the 1st layer squish aka an Elefant Foot effect." msgstr "" "The first layer will be shrunk in the XY plane by the configured value to " "compensate for the 1st layer squish aka an Elefant Foot effect." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:221 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:231 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:852 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1125 msgid "End G-code" msgstr "End G-code" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:222 msgid "" "This end procedure is inserted at the end of the output file. Note that you " "can use placeholder variables for all Slic3r settings." msgstr "" "This end procedure is inserted at the end of the output file. Note that you " "can use placeholder variables for all Slic3r settings." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:232 msgid "" "This end procedure is inserted at the end of the output file, before the " "printer end gcode. Note that you can use placeholder variables for all " "Slic3r settings. If you have multiple extruders, the gcode is processed in " "extruder order." msgstr "" "This end procedure is inserted at the end of the output file, before the " "printer end gcode. Note that you can use placeholder variables for all " "Slic3r settings. If you have multiple extruders, the gcode is processed in " "extruder order." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:242 msgid "Ensure vertical shell thickness" msgstr "Ensure vertical shell thickness" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:244 msgid "" "Add solid infill near sloping surfaces to guarantee the vertical shell " "thickness (top+bottom solid layers)." msgstr "" "Add solid infill near sloping surfaces to guarantee the vertical shell " "thickness (top+bottom solid layers)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:250 msgid "Top/bottom fill pattern" msgstr "Top/bottom fill pattern" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:252 msgid "" "Fill pattern for top/bottom infill. This only affects the external visible " "layer, and not its adjacent solid shells." msgstr "" "Fill pattern for top/bottom infill. This only affects the external visible " "layer, and not its adjacent solid shells." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:271 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:281 msgid "External perimeters" msgstr "External perimeters" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:272 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:381 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:594 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:712 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:969 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1294 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1456 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1616 msgid "Extrusion Width" msgstr "Extrusion width" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:273 msgid "" "Set this to a non-zero value to set a manual extrusion width for external " "perimeters. If left zero, default extrusion width will be used if set, " "otherwise 1.125 x nozzle diameter will be used. If expressed as percentage " "(for example 200%), it will be computed over layer height." msgstr "" "Set this to a non-zero value to set a manual extrusion width for external " "perimeters. If left zero, default extrusion width will be used if set, " "otherwise 1.125 x nozzle diameter will be used. If expressed as percentage " "(for example 200%), it will be computed over layer height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:276 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:599 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:717 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:974 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1298 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1460 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1621 msgid "mm or % (leave 0 for default)" msgstr "mm or % (leave 0 for default)" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:283 msgid "" "This separate setting will affect the speed of external perimeters (the " "visible ones). If expressed as percentage (for example: 80%) it will be " "calculated on the perimeters speed setting above. Set to zero for auto." msgstr "" "This separate setting will affect the speed of external perimeters (the " "visible ones). If expressed as percentage (for example: 80%) it will be " "calculated on the perimeters speed setting above. Set to zero for auto." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:286 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:621 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1257 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1308 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1503 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1633 msgid "mm/s or %" msgstr "mm/s or %" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:293 msgid "External perimeters first" msgstr "External perimeters first" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:295 msgid "" "Print contour perimeters from the outermost one to the innermost one instead " "of the default inverse order." msgstr "" "Print contour perimeters from the outermost one to the innermost one instead " "of the default inverse order." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:301 msgid "Extra perimeters if needed" msgstr "Extra perimeters if needed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:303 #, c-format msgid "" "Add more perimeters when needed for avoiding gaps in sloping walls. Slic3r " "keeps adding perimeters, until more than 70% of the loop immediately above " "is supported." msgstr "" "Add more perimeters when needed for avoiding gaps in sloping walls. Slic3r " "keeps adding perimeters, until more than 70% of the loop immediately above " "is supported." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:311 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:794 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1231 msgid "Extruder" msgstr "Extruder" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:313 msgid "" "The extruder to use (unless more specific extruder settings are specified). " "This value overrides perimeter and infill extruders, but not the support " "extruders." msgstr "" "The extruder to use (unless more specific extruder settings are specified). " "This value overrides perimeter and infill extruders, but not the support " "extruders." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:324 msgid "Height" msgstr "Height" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:325 msgid "" "Set this to the vertical distance between your nozzle tip and (usually) the " "X carriage rods. In other words, this is the height of the clearance " "cylinder around your extruder, and it represents the maximum depth the " "extruder can peek before colliding with other printed objects." msgstr "" "Set this to the vertical distance between your nozzle tip and (usually) the " "X carriage rods. In other words, this is the height of the clearance " "cylinder around your extruder, and it represents the maximum depth the " "extruder can peek before colliding with other printed objects." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:335 msgid "Radius" msgstr "Radius" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:336 msgid "" "Set this to the clearance radius around your extruder. If the extruder is " "not centered, choose the largest value for safety. This setting is used to " "check for collisions and to display the graphical preview in the plater." msgstr "" "Set this to the clearance radius around your extruder. If the extruder is " "not centered, choose the largest value for safety. This setting is used to " "check for collisions and to display the graphical preview in the plater." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:346 msgid "Extruder Color" msgstr "Extruder Color" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:347 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:410 msgid "This is only used in the Slic3r interface as a visual help." msgstr "This is only used in the Slic3r interface as a visual help." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:354 msgid "Extruder offset" msgstr "Extruders offset" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:355 msgid "" "If your firmware doesn't handle the extruder displacement you need the G-" "code to take it into account. This option lets you specify the displacement " "of each extruder with respect to the first one. It expects positive " "coordinates (they will be subtracted from the XY coordinate)." msgstr "" "If your firmware doesn't handle the extruder displacement you need the G-" "code to take it into account. This option lets you specify the displacement " "of each extruder with respect to the first one. It expects positive " "coordinates (they will be subtracted from the XY coordinate)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:364 msgid "Extrusion axis" msgstr "Extrusion axis" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:365 msgid "" "Use this option to set the axis letter associated to your printer's extruder " "(usually E but some printers use A)." msgstr "" "Use this option to set the axis letter associated to your printer's extruder " "(usually E but some printers use A)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:371 msgid "Extrusion multiplier" msgstr "Extrusion multiplier" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:372 msgid "" "This factor changes the amount of flow proportionally. You may need to tweak " "this setting to get nice surface finish and correct single wall widths. " "Usual values are between 0.9 and 1.1. If you think you need to change this " "more, check filament diameter and your firmware E steps." msgstr "" "This factor changes the amount of flow proportionally. You may need to tweak " "this setting to get nice surface finish and correct single wall widths. " "Usual values are between 0.9 and 1.1. If you think you need to change this " "more, check filament diameter and your firmware E steps." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:380 msgid "Default extrusion width" msgstr "Default extrusion width" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:382 msgid "" "Set this to a non-zero value to allow a manual extrusion width. If left to " "zero, Slic3r derives extrusion widths from the nozzle diameter (see the " "tooltips for perimeter extrusion width, infill extrusion width etc). If " "expressed as percentage (for example: 230%), it will be computed over layer " "height." msgstr "" "Set this to a non-zero value to allow a manual extrusion width. If left to " "zero, Slic3r derives extrusion widths from the nozzle diameter (see the " "tooltips for perimeter extrusion width, infill extrusion width etc). If " "expressed as percentage (for example: 230%), it will be computed over layer " "height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:386 msgid "mm or % (leave 0 for auto)" msgstr "mm or % (leave 0 for auto)" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:391 msgid "Keep fan always on" msgstr "Keep fan always on" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:392 msgid "" "If this is enabled, fan will never be disabled and will be kept running at " "least at its minimum speed. Useful for PLA, harmful for ABS." msgstr "" "If this is enabled, fan will never be disabled and will be kept running at " "least at its minimum speed. Useful for PLA, harmful for ABS." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:398 msgid "Enable fan if layer print time is below" msgstr "Enable fan if layer print time is below" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:399 msgid "" "If layer print time is estimated below this number of seconds, fan will be " "enabled and its speed will be calculated by interpolating the minimum and " "maximum speeds." msgstr "" "If layer print time is estimated below this number of seconds, fan will be " "enabled and its speed will be calculated by interpolating the minimum and " "maximum speeds." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:401 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1244 msgid "approximate seconds" msgstr "approximate seconds" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:409 msgid "Color" msgstr "Color" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:416 msgid "Filament notes" msgstr "Filament notes" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:417 msgid "You can put your notes regarding the filament here." msgstr "You can put your notes regarding the filament here." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:425 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:819 msgid "Max volumetric speed" msgstr "Max volumetric speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:426 msgid "" "Maximum volumetric speed allowed for this filament. Limits the maximum " "volumetric speed of a print to the minimum of print and filament volumetric " "speed. Set to zero for no limit." msgstr "" "Maximum volumetric speed allowed for this filament. Limits the maximum " "volumetric speed of a print to the minimum of print and filament volumetric " "speed. Set to zero for no limit." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:429 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:822 msgid "mm\\u00B3/s" msgstr "mm\\u00B3/s" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:436 msgid "" "Enter your filament diameter here. Good precision is required, so use a " "caliper and do multiple measurements along the filament, then compute the " "average." msgstr "" "Enter your filament diameter here. Good precision is required, so use a " "caliper and do multiple measurements along the filament, then compute the " "average." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:444 msgid "Density" msgstr "Density" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:445 msgid "" "Enter your filament density here. This is only for statistical information. " "A decent way is to weigh a known length of filament and compute the ratio of " "the length to volume. Better is to calculate the volume directly through " "displacement." msgstr "" "Enter your filament density here. This is only for statistical information. " "A decent way is to weigh a known length of filament and compute the ratio of " "the length to volume. Better is to calculate the volume directly through " "displacement." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:448 msgid "g/cm\\u00B3" msgstr "g/cm\\u00B3" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:454 msgid "Filament type" msgstr "Filament type" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:455 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1004 msgid "" "If you want to process the output G-code through custom scripts, just list " "their absolute paths here. Separate multiple scripts with a semicolon. " "Scripts will be passed the absolute path to the G-code file as the first " "argument, and they can access the Slic3r config settings by reading " "environment variables." msgstr "" "If you want to process the output G-code through custom scripts, just list " "their absolute paths here. Separate multiple scripts with a semicolon. " "Scripts will be passed the absolute path to the G-code file as the first " "argument, and they can access the Slic3r config settings by reading " "environment variables." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:474 msgid "Soluble material" msgstr "Soluble material" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:475 msgid "Soluble material is most likely used for a soluble support." msgstr "Soluble material is most likely used for a soluble support." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:480 msgid "Cost" msgstr "Cost" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:481 msgid "" "Enter your filament cost per kg here. This is only for statistical " "information." msgstr "" "Enter your filament cost per kg here. This is only for statistical " "information." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:482 msgid "money/kg" msgstr "money/kg" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:491 msgid "Fill angle" msgstr "Fill angle" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:493 msgid "" "Default base angle for infill orientation. Cross-hatching will be applied to " "this. Bridges will be infilled using the best direction Slic3r can detect, " "so this setting does not affect them." msgstr "" "Default base angle for infill orientation. Cross-hatching will be applied to " "this. Bridges will be infilled using the best direction Slic3r can detect, " "so this setting does not affect them." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:505 msgid "Fill density" msgstr "Fill density" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:507 #, c-format msgid "Density of internal infill, expressed in the range 0% - 100%." msgstr "Density of internal infill, expressed in the range 0% - 100%." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:543 msgid "Fill pattern" msgstr "Fill pattern" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:545 msgid "Fill pattern for general low-density infill." msgstr "Fill pattern for general low-density infill." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:575 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:584 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:593 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:627 msgid "First layer" msgstr "First layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:576 msgid "" "This is the acceleration your printer will use for first layer. Set zero to " "disable acceleration control for first layer." msgstr "" "This is the acceleration your printer will use for first layer. Set zero to " "disable acceleration control for first layer." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:585 msgid "" "Heated build plate temperature for the first layer. Set this to zero to " "disable bed temperature control commands in the output." msgstr "" "Heated build plate temperature for the first layer. Set this to zero to " "disable bed temperature control commands in the output." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:595 msgid "" "Set this to a non-zero value to set a manual extrusion width for first " "layer. You can use this to force fatter extrudates for better adhesion. If " "expressed as percentage (for example 120%) it will be computed over first " "layer height. If set to zero, it will use the default extrusion width." msgstr "" "Set this to a non-zero value to set a manual extrusion width for first " "layer. You can use this to force fatter extrudates for better adhesion. If " "expressed as percentage (for example 120%) it will be computed over first " "layer height. If set to zero, it will use the default extrusion width." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:605 msgid "First layer height" msgstr "First layer height" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:607 msgid "" "When printing with very low layer heights, you might still want to print a " "thicker bottom layer to improve adhesion and tolerance for non perfect build " "plates. This can be expressed as an absolute value or as a percentage (for " "example: 150%) over the default layer height." msgstr "" "When printing with very low layer heights, you might still want to print a " "thicker bottom layer to improve adhesion and tolerance for non perfect build " "plates. This can be expressed as an absolute value or as a percentage (for " "example: 150%) over the default layer height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:611 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:742 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1392 msgid "mm or %" msgstr "mm or %" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:617 msgid "First layer speed" msgstr "First layer speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:618 msgid "" "If expressed as absolute value in mm/s, this speed will be applied to all " "the print moves of the first layer, regardless of their type. If expressed " "as a percentage (for example: 40%) it will scale the default speeds." msgstr "" "If expressed as absolute value in mm/s, this speed will be applied to all " "the print moves of the first layer, regardless of their type. If expressed " "as a percentage (for example: 40%) it will scale the default speeds." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:628 msgid "" "Extruder temperature for first layer. If you want to control temperature " "manually during print, set this to zero to disable temperature control " "commands in the output file." msgstr "" "Extruder temperature for first layer. If you want to control temperature " "manually during print, set this to zero to disable temperature control " "commands in the output file." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:636 msgid "Gap fill" msgstr "Gap fill" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:638 msgid "" "Speed for filling small gaps using short zigzag moves. Keep this reasonably " "low to avoid too much shaking and resonance issues. Set zero to disable gaps " "filling." msgstr "" "Speed for filling small gaps using short zigzag moves. Keep this reasonably " "low to avoid too much shaking and resonance issues. Set zero to disable gaps " "filling." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:646 msgid "Verbose G-code" msgstr "Verbose G-code" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:647 msgid "" "Enable this to get a commented G-code file, with each line explained by a " "descriptive text. If you print from SD card, the additional weight of the " "file could make your firmware slow down." msgstr "" "Enable this to get a commented G-code file, with each line explained by a " "descriptive text. If you print from SD card, the additional weight of the " "file could make your firmware slow down." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:654 msgid "G-code flavor" msgstr "G-code flavor" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:655 msgid "" "Some G/M-code commands, including temperature control and others, are not " "universal. Set this option to your printer's firmware to get a compatible " "output. The \"No extrusion\" flavor prevents Slic3r from exporting any " "extrusion value at all." msgstr "" "Some G/M-code commands, including temperature control and others, are not " "universal. Set this option to your printer's firmware to get a compatible " "output. The \"No extrusion\" flavor prevents Slic3r from exporting any " "extrusion value at all." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:684 msgid "" "This is the acceleration your printer will use for infill. Set zero to " "disable acceleration control for infill." msgstr "" "This is the acceleration your printer will use for infill. Set zero to " "disable acceleration control for infill." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:692 msgid "Combine infill every" msgstr "Combine infill every" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:694 msgid "" "This feature allows to combine infill and speed up your print by extruding " "thicker infill layers while preserving thin perimeters, thus accuracy." msgstr "" "This feature allows to combine infill and speed up your print by extruding " "thicker infill layers while preserving thin perimeters, thus accuracy." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:698 msgid "Combine infill every n layers" msgstr "Combine infill every n layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:703 msgid "Infill extruder" msgstr "Infill extruder" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:705 msgid "The extruder to use when printing infill." msgstr "The extruder to use when printing infill." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:713 msgid "" "Set this to a non-zero value to set a manual extrusion width for infill. If " "left zero, default extrusion width will be used if set, otherwise 1.125 x " "nozzle diameter will be used. You may want to use fatter extrudates to speed " "up the infill and make your parts stronger. If expressed as percentage (for " "example 90%) it will be computed over layer height." msgstr "" "Set this to a non-zero value to set a manual extrusion width for infill. If " "left zero, default extrusion width will be used if set, otherwise 1.125 x " "nozzle diameter will be used. You may want to use fatter extrudates to speed " "up the infill and make your parts stronger. If expressed as percentage (for " "example 90%) it will be computed over layer height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:722 msgid "Infill before perimeters" msgstr "Infill before perimeters" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:723 msgid "" "This option will switch the print order of perimeters and infill, making the " "latter first." msgstr "" "This option will switch the print order of perimeters and infill, making the " "latter first." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:728 msgid "Only infill where needed" msgstr "Only infill where needed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:730 msgid "" "This option will limit infill to the areas actually needed for supporting " "ceilings (it will act as internal support material). If enabled, slows down " "the G-code generation due to the multiple checks involved." msgstr "" "This option will limit infill to the areas actually needed for supporting " "ceilings (it will act as internal support material). If enabled, slows down " "the G-code generation due to the multiple checks involved." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:737 msgid "Infill/perimeters overlap" msgstr "Infill/perimeters overlap" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:739 msgid "" "This setting applies an additional overlap between infill and perimeters for " "better bonding. Theoretically this shouldn't be needed, but backlash might " "cause gaps. If expressed as percentage (example: 15%) it is calculated over " "perimeter extrusion width." msgstr "" "This setting applies an additional overlap between infill and perimeters for " "better bonding. Theoretically this shouldn't be needed, but backlash might " "cause gaps. If expressed as percentage (example: 15%) it is calculated over " "perimeter extrusion width." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:750 msgid "Speed for printing the internal fill. Set to zero for auto." msgstr "Speed for printing the internal fill. Set to zero for auto." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:759 msgid "Interface shells" msgstr "Interface shells" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:760 msgid "" "Force the generation of solid shells between adjacent materials/volumes. " "Useful for multi-extruder prints with translucent materials or manual " "soluble support material." msgstr "" "Force the generation of solid shells between adjacent materials/volumes. " "Useful for multi-extruder prints with translucent materials or manual " "soluble support material." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:768 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1137 msgid "After layer change G-code" msgstr "After layer change G-code" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:769 msgid "" "This custom code is inserted at every layer change, right after the Z move " "and before the extruder moves to the first layer point. Note that you can " "use placeholder variables for all Slic3r settings as well as [layer_num] and " "[layer_z]." msgstr "" "This custom code is inserted at every layer change, right after the Z move " "and before the extruder moves to the first layer point. Note that you can " "use placeholder variables for all Slic3r settings as well as [layer_num] and " "[layer_z]." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:779 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:315 msgid "Layer height" msgstr "Layer height" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:781 msgid "" "This setting controls the height (and thus the total number) of the slices/" "layers. Thinner layers give better accuracy but take more time to print." msgstr "" "This setting controls the height (and thus the total number) of the slices/" "layers. Thinner layers give better accuracy but take more time to print." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:789 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:798 msgid "Max" msgstr "Max" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:790 msgid "This setting represents the maximum speed of your fan." msgstr "This setting represents the maximum speed of your fan." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:799 #, c-format msgid "" "This is the highest printable layer height for this extruder, used to cap " "the variable layer height and support layer height. Maximum recommended " "layer height is 75% of the extrusion width to achieve reasonable inter-layer " "adhesion. If set to 0, layer height is limited to 75% of the nozzle diameter." msgstr "" "This is the highest printable layer height for this extruder, used to cap " "the variable layer height and support layer height. Maximum recommended " "layer height is 75% of the extrusion width to achieve reasonable inter-layer " "adhesion. If set to 0, layer height is limited to 75% of the nozzle diameter." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:809 msgid "Max print speed" msgstr "Max print speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:810 msgid "" "When setting other speed settings to 0 Slic3r will autocalculate the optimal " "speed in order to keep constant extruder pressure. This experimental setting " "is used to set the highest print speed you want to allow." msgstr "" "When setting other speed settings to 0 Slic3r will autocalculate the optimal " "speed in order to keep constant extruder pressure. This experimental setting " "is used to set the highest print speed you want to allow." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:820 msgid "" "This experimental setting is used to set the maximum volumetric speed your " "extruder supports." msgstr "" "This experimental setting is used to set the maximum volumetric speed your " "extruder supports." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:828 msgid "Max volumetric slope positive" msgstr "Max volumetric slope positive" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:829 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:840 msgid "" "This experimental setting is used to limit the speed of change in extrusion " "rate. A value of 1.8 mm\\u00B3/s\\u00B2 ensures, that a change from the " "extrusion rate of 1.8 mm\\u00B3/s (0.45mm extrusion width, 0.2mm extrusion " "height, feedrate 20 mm/s) to 5.4 mm\\u00B3/s (feedrate 60 mm/s) will take at " "least 2 seconds." msgstr "" "This experimental setting is used to limit the speed of change in extrusion " "rate. A value of 1.8 mm\\u00B3/s\\u00B2 ensures, that a change from the " "extrusion rate of 1.8 mm\\u00B3/s (0.45mm extrusion width, 0.2mm extrusion " "height, feedrate 20 mm/s) to 5.4 mm\\u00B3/s (feedrate 60 mm/s) will take at " "least 2 seconds." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:833 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:844 msgid "mm\\u00B3/s\\u00B2" msgstr "mm\\u00B3/s\\u00B2" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:839 msgid "Max volumetric slope negative" msgstr "Max volumetric slope negative" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:850 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:859 msgid "Min" msgstr "Min" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:851 msgid "This setting represents the minimum PWM your fan needs to work." msgstr "This setting represents the minimum PWM your fan needs to work." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:860 msgid "" "This is the lowest printable layer height for this extruder and limits the " "resolution for variable layer height. Typical values are between 0.05 mm and " "0.1 mm." msgstr "" "This is the lowest printable layer height for this extruder and limits the " "resolution for variable layer height. Typical values are between 0.05 mm and " "0.1 mm." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:868 msgid "Min print speed" msgstr "Min print speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:869 msgid "Slic3r will not scale speed down below this speed." msgstr "Slic3r will not scale speed down below this speed." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:876 msgid "Minimum extrusion length" msgstr "Minimum extrusion length" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:877 msgid "" "Generate no less than the number of skirt loops required to consume the " "specified amount of filament on the bottom layer. For multi-extruder " "machines, this minimum applies to each extruder." msgstr "" "Generate no less than the number of skirt loops required to consume the " "specified amount of filament on the bottom layer. For multi-extruder " "machines, this minimum applies to each extruder." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:886 msgid "Configuration notes" msgstr "Configuration notes" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:887 msgid "" "You can put here your personal notes. This text will be added to the G-code " "header comments." msgstr "" "You can put here your personal notes. This text will be added to the G-code " "header comments." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:896 msgid "Nozzle diameter" msgstr "Nozzle diameter" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:897 msgid "" "This is the diameter of your extruder nozzle (for example: 0.5, 0.35 etc.)" msgstr "" "This is the diameter of your extruder nozzle (for example: 0.5, 0.35 etc.)" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:903 msgid "API Key" msgstr "API Key" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:904 msgid "" "Slic3r can upload G-code files to OctoPrint. This field should contain the " "API Key required for authentication." msgstr "" "Slic3r can upload G-code files to OctoPrint. This field should contain the " "API Key required for authentication." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:910 msgid "Host or IP" msgstr "Host or IP" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:911 msgid "" "Slic3r can upload G-code files to OctoPrint. This field should contain the " "hostname or IP address of the OctoPrint instance." msgstr "" "Slic3r can upload G-code files to OctoPrint. This field should contain the " "hostname or IP address of the OctoPrint instance." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:917 msgid "Only retract when crossing perimeters" msgstr "Only retract when crossing perimeters" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:918 msgid "" "Disables retraction when the travel path does not exceed the upper layer's " "perimeters (and thus any ooze will be probably invisible)." msgstr "" "Disables retraction when the travel path does not exceed the upper layer's " "perimeters (and thus any ooze will be probably invisible)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:924 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1697 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:805 msgid "Enable" msgstr "Enable" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:925 msgid "" "This option will drop the temperature of the inactive extruders to prevent " "oozing. It will enable a tall skirt automatically and move extruders outside " "such skirt when changing temperatures." msgstr "" "This option will drop the temperature of the inactive extruders to prevent " "oozing. It will enable a tall skirt automatically and move extruders outside " "such skirt when changing temperatures." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:932 msgid "Output filename format" msgstr "Output filename format" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:933 msgid "" "You can use all configuration options as variables inside this template. For " "example: [layer_height], [fill_density] etc. You can also use [timestamp], " "[year], [month], [day], [hour], [minute], [second], [version], " "[input_filename], [input_filename_base]." msgstr "" "You can use all configuration options as variables inside this template. For " "example: [layer_height], [fill_density] etc. You can also use [timestamp], " "[year], [month], [day], [hour], [minute], [second], [version], " "[input_filename], [input_filename_base]." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:942 msgid "Detect bridging perimeters" msgstr "Detect bridging perimeters" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:944 msgid "" "Experimental option to adjust flow for overhangs (bridge flow will be used), " "to apply bridge speed to them and enable fan." msgstr "" "Experimental option to adjust flow for overhangs (bridge flow will be used), " "to apply bridge speed to them and enable fan." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:950 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:968 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:980 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:990 msgid "Perimeters" msgstr "Perimeters" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:951 msgid "" "This is the acceleration your printer will use for perimeters. A high value " "like 9000 usually gives good results if your hardware is up to the job. Set " "zero to disable acceleration control for perimeters." msgstr "" "This is the acceleration your printer will use for perimeters. A high value " "like 9000 usually gives good results if your hardware is up to the job. Set " "zero to disable acceleration control for perimeters." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:959 msgid "Perimeter extruder" msgstr "Perimeter extruder" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:961 msgid "" "The extruder to use when printing perimeters and brim. First extruder is 1." msgstr "" "The extruder to use when printing perimeters and brim. First extruder is 1." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:970 msgid "" "Set this to a non-zero value to set a manual extrusion width for perimeters. " "You may want to use thinner extrudates to get more accurate surfaces. If " "left zero, default extrusion width will be used if set, otherwise 1.125 x " "nozzle diameter will be used. If expressed as percentage (for example 200%) " "it will be computed over layer height." msgstr "" "Set this to a non-zero value to set a manual extrusion width for perimeters. " "You may want to use thinner extrudates to get more accurate surfaces. If " "left zero, default extrusion width will be used if set, otherwise 1.125 x " "nozzle diameter will be used. If expressed as percentage (for example 200%) " "it will be computed over layer height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:982 msgid "" "Speed for perimeters (contours, aka vertical shells). Set to zero for auto." msgstr "" "Speed for perimeters (contours, aka vertical shells). Set to zero for auto." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:992 msgid "" "This option sets the number of perimeters to generate for each layer. Note " "that Slic3r may increase this number automatically when it detects sloping " "surfaces which benefit from a higher number of perimeters if the Extra " "Perimeters option is enabled." msgstr "" "This option sets the number of perimeters to generate for each layer. Note " "that Slic3r may increase this number automatically when it detects sloping " "surfaces which benefit from a higher number of perimeters if the Extra " "Perimeters option is enabled." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:996 msgid "(minimum)" msgstr "(minimum)" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1003 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:495 msgid "Post-processing scripts" msgstr "Post-processing scripts" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1016 msgid "Printer notes" msgstr "Printer notes" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1017 msgid "You can put your notes regarding the printer here." msgstr "You can put your notes regarding the printer here." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1031 msgid "Raft layers" msgstr "Raft layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1033 msgid "" "The object will be raised by this number of layers, and support material " "will be generated under it." msgstr "" "The object will be raised by this number of layers, and support material " "will be generated under it." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1041 msgid "Resolution" msgstr "Resolution" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1042 msgid "" "Minimum detail resolution, used to simplify the input file for speeding up " "the slicing job and reducing memory usage. High-resolution models often " "carry more detail than printers can render. Set to zero to disable any " "simplification and use full resolution from input." msgstr "" "Minimum detail resolution, used to simplify the input file for speeding up " "the slicing job and reducing memory usage. High-resolution models often " "carry more detail than printers can render. Set to zero to disable any " "simplification and use full resolution from input." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1052 msgid "Minimum travel after retraction" msgstr "Minimum travel after retraction" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1053 msgid "" "Retraction is not triggered when travel moves are shorter than this length." msgstr "" "Retraction is not triggered when travel moves are shorter than this length." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1059 msgid "Retract amount before wipe" msgstr "Retract amount before wipe" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1060 msgid "" "With bowden extruders, it may be wise to do some amount of quick retract " "before doing the wipe movement." msgstr "" "With bowden extruders, it may be wise to do some amount of quick retract " "before doing the wipe movement." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1067 msgid "Retract on layer change" msgstr "Retract on layer change" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1068 msgid "This flag enforces a retraction whenever a Z move is done." msgstr "This flag enforces a retraction whenever a Z move is done." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1073 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1082 msgid "Length" msgstr "Length" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1074 msgid "Retraction Length" msgstr "Retraction Length" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1075 msgid "" "When retraction is triggered, filament is pulled back by the specified " "amount (the length is measured on raw filament, before it enters the " "extruder)." msgstr "" "When retraction is triggered, filament is pulled back by the specified " "amount (the length is measured on raw filament, before it enters the " "extruder)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1077 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1087 msgid "mm (zero to disable)" msgstr "mm (zero to disable)" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1083 msgid "Retraction Length (Toolchange)" msgstr "Retraction Length (Toolchange)" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1084 msgid "" "When retraction is triggered before changing tool, filament is pulled back " "by the specified amount (the length is measured on raw filament, before it " "enters the extruder)." msgstr "" "When retraction is triggered before changing tool, filament is pulled back " "by the specified amount (the length is measured on raw filament, before it " "enters the extruder)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1092 msgid "Lift Z" msgstr "Lift Z" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1093 msgid "" "If you set this to a positive value, Z is quickly raised every time a " "retraction is triggered. When using multiple extruders, only the setting for " "the first extruder will be considered." msgstr "" "If you set this to a positive value, Z is quickly raised every time a " "retraction is triggered. When using multiple extruders, only the setting for " "the first extruder will be considered." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1101 msgid "Above Z" msgstr "Above Z" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1102 msgid "Only lift Z above" msgstr "Only lift Z above" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1103 msgid "" "If you set this to a positive value, Z lift will only take place above the " "specified absolute Z. You can tune this setting for skipping lift on the " "first layers." msgstr "" "If you set this to a positive value, Z lift will only take place above the " "specified absolute Z. You can tune this setting for skipping lift on the " "first layers." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1110 msgid "Below Z" msgstr "Below Z" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1111 msgid "Only lift Z below" msgstr "Only lift Z below" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1112 msgid "" "If you set this to a positive value, Z lift will only take place below the " "specified absolute Z. You can tune this setting for limiting lift to the " "first layers." msgstr "" "If you set this to a positive value, Z lift will only take place below the " "specified absolute Z. You can tune this setting for limiting lift to the " "first layers." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1120 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1128 msgid "Extra length on restart" msgstr "Extra length on restart" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1121 msgid "" "When the retraction is compensated after the travel move, the extruder will " "push this additional amount of filament. This setting is rarely needed." msgstr "" "When the retraction is compensated after the travel move, the extruder will " "push this additional amount of filament. This setting is rarely needed." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1129 msgid "" "When the retraction is compensated after changing tool, the extruder will " "push this additional amount of filament." msgstr "" "When the retraction is compensated after changing tool, the extruder will " "push this additional amount of filament." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1136 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1137 msgid "Retraction Speed" msgstr "Retraction Speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1138 msgid "The speed for retractions (it only applies to the extruder motor)." msgstr "The speed for retractions (it only applies to the extruder motor)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1144 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1145 msgid "Deretraction Speed" msgstr "Deretraction Speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1146 msgid "" "The speed for loading of a filament into extruder after retraction (it only " "applies to the extruder motor). If left to zero, the retraction speed is " "used." msgstr "" "The speed for loading of a filament into extruder after retraction (it only " "applies to the extruder motor). If left to zero, the retraction speed is " "used." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1153 msgid "Seam position" msgstr "Seam position" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1155 msgid "Position of perimeters starting points." msgstr "Position of perimeters starting points." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1171 msgid "Direction" msgstr "Direction" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1173 msgid "Preferred direction of the seam" msgstr "Preferred direction of the seam" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1174 msgid "Seam preferred direction" msgstr "Seam preferred direction" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1182 msgid "Jitter" msgstr "Jitter" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1184 msgid "Seam preferred direction jitter" msgstr "Seam preferred direction jitter" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1185 msgid "Preferred direction of the seam - jitter" msgstr "Preferred direction of the seam - jitter" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1195 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:989 msgid "Serial port" msgstr "Serial port" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1196 msgid "USB/serial port for printer connection." msgstr "USB/serial port for printer connection." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1204 msgid "Serial port speed" msgstr "Serial port speed" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1205 msgid "Speed (baud) of USB/serial port for printer connection." msgstr "Speed (baud) of USB/serial port for printer connection." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1214 msgid "Distance from object" msgstr "Distance from object" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1215 msgid "" "Distance between skirt and object(s). Set this to zero to attach the skirt " "to the object(s) and get a brim for better adhesion." msgstr "" "Distance between skirt and object(s). Set this to zero to attach the skirt " "to the object(s) and get a brim for better adhesion." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1223 msgid "Skirt height" msgstr "Skirt height" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1224 msgid "" "Height of skirt expressed in layers. Set this to a tall value to use skirt " "as a shield against drafts." msgstr "" "Height of skirt expressed in layers. Set this to a tall value to use skirt " "as a shield against drafts." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1231 msgid "Loops (minimum)" msgstr "Loops (minimum)" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1232 msgid "Skirt Loops" msgstr "Skirt Loops" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1233 msgid "" "Number of loops for the skirt. If the Minimum Extrusion Length option is " "set, the number of loops might be greater than the one configured here. Set " "this to zero to disable skirt completely." msgstr "" "Number of loops for the skirt. If the Minimum Extrusion Length option is " "set, the number of loops might be greater than the one configured here. Set " "this to zero to disable skirt completely." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1241 msgid "Slow down if layer print time is below" msgstr "Slow down if layer print time is below" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1242 msgid "" "If layer print time is estimated below this number of seconds, print moves " "speed will be scaled down to extend duration to this value." msgstr "" "If layer print time is estimated below this number of seconds, print moves " "speed will be scaled down to extend duration to this value." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1252 msgid "Small perimeters" msgstr "Small perimeters" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1254 msgid "" "This separate setting will affect the speed of perimeters having radius <= " "6.5mm (usually holes). If expressed as percentage (for example: 80%) it will " "be calculated on the perimeters speed setting above. Set to zero for auto." msgstr "" "This separate setting will affect the speed of perimeters having radius <= " "6.5mm (usually holes). If expressed as percentage (for example: 80%) it will " "be calculated on the perimeters speed setting above. Set to zero for auto." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1264 msgid "Solid infill threshold area" msgstr "Solid infill threshold area" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1266 msgid "" "Force solid infill for regions having a smaller area than the specified " "threshold." msgstr "" "Force solid infill for regions having a smaller area than the specified " "threshold." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1267 msgid "mm\\u00B2" msgstr "mm\\u00B2" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1273 msgid "Solid infill extruder" msgstr "Solid infill extruder" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1275 msgid "The extruder to use when printing solid infill." msgstr "The extruder to use when printing solid infill." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1281 msgid "Solid infill every" msgstr "Solid infill every" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1283 msgid "" "This feature allows to force a solid layer every given number of layers. " "Zero to disable. You can set this to any value (for example 9999); Slic3r " "will automatically choose the maximum possible number of layers to combine " "according to nozzle diameter and layer height." msgstr "" "This feature allows to force a solid layer every given number of layers. " "Zero to disable. You can set this to any value (for example 9999); Slic3r " "will automatically choose the maximum possible number of layers to combine " "according to nozzle diameter and layer height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1293 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1303 msgid "Solid infill" msgstr "Solid infill" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1295 msgid "" "Set this to a non-zero value to set a manual extrusion width for infill for " "solid surfaces. If left zero, default extrusion width will be used if set, " "otherwise 1.125 x nozzle diameter will be used. If expressed as percentage " "(for example 90%) it will be computed over layer height." msgstr "" "Set this to a non-zero value to set a manual extrusion width for infill for " "solid surfaces. If left zero, default extrusion width will be used if set, " "otherwise 1.125 x nozzle diameter will be used. If expressed as percentage " "(for example 90%) it will be computed over layer height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1305 msgid "" "Speed for printing solid regions (top/bottom/internal horizontal shells). " "This can be expressed as a percentage (for example: 80%) over the default " "infill speed above. Set to zero for auto." msgstr "" "Speed for printing solid regions (top/bottom/internal horizontal shells). " "This can be expressed as a percentage (for example: 80%) over the default " "infill speed above. Set to zero for auto." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1316 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:331 msgid "Solid layers" msgstr "Solid layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1317 msgid "Number of solid layers to generate on top and bottom surfaces." msgstr "Number of solid layers to generate on top and bottom surfaces." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1324 msgid "Spiral vase" msgstr "Spiral vase" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1325 msgid "" "This feature will raise Z gradually while printing a single-walled object in " "order to remove any visible seam. This option requires a single perimeter, " "no infill, no top solid layers and no support material. You can still set " "any number of bottom solid layers as well as skirt/brim loops. It won't work " "when printing more than an object." msgstr "" "This feature will raise Z gradually while printing a single-walled object in " "order to remove any visible seam. This option requires a single perimeter, " "no infill, no top solid layers and no support material. You can still set " "any number of bottom solid layers as well as skirt/brim loops. It won't work " "when printing more than an object." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1334 msgid "Temperature variation" msgstr "Temperature variation" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1335 msgid "" "Temperature difference to be applied when an extruder is not active. Enables " "a full-height \"sacrificial\" skirt on which the nozzles are periodically " "wiped." msgstr "" "Temperature difference to be applied when an extruder is not active. Enables " "a full-height \"sacrificial\" skirt on which the nozzles are periodically " "wiped." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1344 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1359 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:846 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1119 msgid "Start G-code" msgstr "Start G-code" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1345 msgid "" "This start procedure is inserted at the beginning, after bed has reached the " "target temperature and extruder just started heating, and before extruder " "has finished heating. If Slic3r detects M104 or M190 in your custom codes, " "such commands will not be prepended automatically so you're free to " "customize the order of heating commands and other custom actions. Note that " "you can use placeholder variables for all Slic3r settings, so you can put a " "\"M109 S[first_layer_temperature]\" command wherever you want." msgstr "" "This start procedure is inserted at the beginning, after bed has reached the " "target temperature and extruder just started heating, and before extruder " "has finished heating. If Slic3r detects M104 or M190 in your custom codes, " "such commands will not be prepended automatically so you're free to " "customize the order of heating commands and other custom actions. Note that " "you can use placeholder variables for all Slic3r settings, so you can put a " "\"M109 S[first_layer_temperature]\" command wherever you want." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1360 msgid "" "This start procedure is inserted at the beginning, after any printer start " "gcode. This is used to override settings for a specific filament. If Slic3r " "detects M104, M109, M140 or M190 in your custom codes, such commands will " "not be prepended automatically so you're free to customize the order of " "heating commands and other custom actions. Note that you can use placeholder " "variables for all Slic3r settings, so you can put a \"M109 " "S[first_layer_temperature]\" command wherever you want. If you have multiple " "extruders, the gcode is processed in extruder order." msgstr "" "This start procedure is inserted at the beginning, after any printer start " "gcode. This is used to override settings for a specific filament. If Slic3r " "detects M104, M109, M140 or M190 in your custom codes, such commands will " "not be prepended automatically so you're free to customize the order of " "heating commands and other custom actions. Note that you can use placeholder " "variables for all Slic3r settings, so you can put a \"M109 " "S[first_layer_temperature]\" command wherever you want. If you have multiple " "extruders, the gcode is processed in extruder order." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1375 msgid "Single Extruder Multi Material" msgstr "Single Extruder Multi Material" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1376 msgid "The printer multiplexes filaments into a single hot end." msgstr "The printer multiplexes filaments into a single hot end." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1381 msgid "Generate support material" msgstr "Generate support material" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1383 msgid "Enable support material generation." msgstr "Enable support material generation." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1388 msgid "XY separation between an object and its support" msgstr "XY separation between an object and its support" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1390 msgid "" "XY separation between an object and its support. If expressed as percentage " "(for example 50%), it will be calculated over external perimeter width." msgstr "" "XY separation between an object and its support. If expressed as percentage " "(for example 50%), it will be calculated over external perimeter width." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1400 msgid "Pattern angle" msgstr "Pattern angle" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1402 msgid "" "Use this setting to rotate the support material pattern on the horizontal " "plane." msgstr "" "Use this setting to rotate the support material pattern on the horizontal " "plane." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1410 msgid "Support on build plate only" msgstr "Support on build plate only" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1412 msgid "" "Only create support if it lies on a build plate. Don't create support on a " "print." msgstr "" "Only create support if it lies on a build plate. Don't create support on a " "print." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1418 msgid "Contact Z distance" msgstr "Contact Z distance" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1420 msgid "" "The vertical distance between object and support material interface. Setting " "this to 0 will also prevent Slic3r from using bridge flow and speed for the " "first object layer." msgstr "" "The vertical distance between object and support material interface. Setting " "this to 0 will also prevent Slic3r from using bridge flow and speed for the " "first object layer." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1433 msgid "Enforce support for the first" msgstr "Enforce support for the first" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1435 msgid "" "Generate support material for the specified number of layers counting from " "bottom, regardless of whether normal support material is enabled or not and " "regardless of any angle threshold. This is useful for getting more adhesion " "of objects having a very thin or poor footprint on the build plate." msgstr "" "Generate support material for the specified number of layers counting from " "bottom, regardless of whether normal support material is enabled or not and " "regardless of any angle threshold. This is useful for getting more adhesion " "of objects having a very thin or poor footprint on the build plate." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1441 msgid "Enforce support for the first n layers" msgstr "Enforce support for the first n layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1446 msgid "Support material/raft/skirt extruder" msgstr "Support material/raft/skirt extruder" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1448 msgid "" "The extruder to use when printing support material, raft and skirt (1+, 0 to " "use the current extruder to minimize tool changes)." msgstr "" "The extruder to use when printing support material, raft and skirt (1+, 0 to " "use the current extruder to minimize tool changes)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1457 msgid "" "Set this to a non-zero value to set a manual extrusion width for support " "material. If left zero, default extrusion width will be used if set, " "otherwise nozzle diameter will be used. If expressed as percentage (for " "example 90%) it will be computed over layer height." msgstr "" "Set this to a non-zero value to set a manual extrusion width for support " "material. If left zero, default extrusion width will be used if set, " "otherwise nozzle diameter will be used. If expressed as percentage (for " "example 90%) it will be computed over layer height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1465 msgid "Interface loops" msgstr "Interface loops" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1467 msgid "" "Cover the top contact layer of the supports with loops. Disabled by default." msgstr "" "Cover the top contact layer of the supports with loops. Disabled by default." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1472 msgid "Support material/raft interface extruder" msgstr "Support material/raft interface extruder" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1474 msgid "" "The extruder to use when printing support material interface (1+, 0 to use " "the current extruder to minimize tool changes). This affects raft too." msgstr "" "The extruder to use when printing support material interface (1+, 0 to use " "the current extruder to minimize tool changes). This affects raft too." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1481 msgid "Interface layers" msgstr "Interface layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1483 msgid "" "Number of interface layers to insert between the object(s) and support " "material." msgstr "" "Number of interface layers to insert between the object(s) and support " "material." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1490 msgid "Interface pattern spacing" msgstr "Interface pattern spacing" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1492 msgid "Spacing between interface lines. Set zero to get a solid interface." msgstr "Spacing between interface lines. Set zero to get a solid interface." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1499 msgid "Support material interface" msgstr "Support material interface" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1501 msgid "" "Speed for printing support material interface layers. If expressed as " "percentage (for example 50%) it will be calculated over support material " "speed." msgstr "" "Speed for printing support material interface layers. If expressed as " "percentage (for example 50%) it will be calculated over support material " "speed." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1510 msgid "Pattern" msgstr "Pattern" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1512 msgid "Pattern used to generate support material." msgstr "Pattern used to generate support material." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1526 msgid "Pattern spacing" msgstr "Pattern spacing" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1528 msgid "Spacing between support material lines." msgstr "Spacing between support material lines." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1537 msgid "Speed for printing support material." msgstr "Speed for printing support material." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1544 msgid "Synchronize with object layers" msgstr "Synchronize with object layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1546 msgid "" "Synchronize support layers with the object print layers. This is useful with " "multi-material printers, where the extruder switch is expensive." msgstr "" "Synchronize support layers with the object print layers. This is useful with " "multi-material printers, where the extruder switch is expensive." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1552 msgid "Overhang threshold" msgstr "Overhang threshold" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1554 msgid "" "Support material will not be generated for overhangs whose slope angle " "(90\\u00B0 = vertical) is above the given threshold. In other words, this " "value represent the most horizontal slope (measured from the horizontal " "plane) that you can print without support material. Set to zero for " "automatic detection (recommended)." msgstr "" "Support material will not be generated for overhangs whose slope angle " "(90\\u00B0 = vertical) is above the given threshold. In other words, this " "value represent the most horizontal slope (measured from the horizontal " "plane) that you can print without support material. Set to zero for " "automatic detection (recommended)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1566 msgid "With sheath around the support" msgstr "With sheath around the support" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1568 msgid "" "Add a sheath (a single perimeter line) around the base support. This makes " "the support more reliable, but also more difficult to remove." msgstr "" "Add a sheath (a single perimeter line) around the base support. This makes " "the support more reliable, but also more difficult to remove." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1575 msgid "" "Extruder temperature for layers after the first one. Set this to zero to " "disable temperature control commands in the output." msgstr "" "Extruder temperature for layers after the first one. Set this to zero to " "disable temperature control commands in the output." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1578 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:793 msgid "Temperature" msgstr "Temperature" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1584 msgid "Detect thin walls" msgstr "Detect thin walls" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1586 msgid "" "Detect single-width walls (parts where two extrusions don't fit and we need " "to collapse them into a single trace)." msgstr "" "Detect single-width walls (parts where two extrusions don't fit and we need " "to collapse them into a single trace)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1592 msgid "Threads" msgstr "Threads" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1593 msgid "" "Threads are used to parallelize long-running tasks. Optimal threads number " "is slightly above the number of available cores/processors." msgstr "" "Threads are used to parallelize long-running tasks. Optimal threads number " "is slightly above the number of available cores/processors." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1604 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1143 msgid "Tool change G-code" msgstr "Tool change G-code" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1605 msgid "" "This custom code is inserted right before every extruder change. Note that " "you can use placeholder variables for all Slic3r settings as well as " "[previous_extruder] and [next_extruder]." msgstr "" "This custom code is inserted right before every extruder change. Note that " "you can use placeholder variables for all Slic3r settings as well as " "[previous_extruder] and [next_extruder]." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1615 #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1626 msgid "Top solid infill" msgstr "Top solid infill" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1617 msgid "" "Set this to a non-zero value to set a manual extrusion width for infill for " "top surfaces. You may want to use thinner extrudates to fill all narrow " "regions and get a smoother finish. If left zero, default extrusion width " "will be used if set, otherwise nozzle diameter will be used. If expressed as " "percentage (for example 90%) it will be computed over layer height." msgstr "" "Set this to a non-zero value to set a manual extrusion width for infill for " "top surfaces. You may want to use thinner extrudates to fill all narrow " "regions and get a smoother finish. If left zero, default extrusion width " "will be used if set, otherwise nozzle diameter will be used. If expressed as " "percentage (for example 90%) it will be computed over layer height." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1628 msgid "" "Speed for printing top solid layers (it only applies to the uppermost " "external layers and not to their internal solid layers). You may want to " "slow down this to get a nicer surface finish. This can be expressed as a " "percentage (for example: 80%) over the solid infill speed above. Set to zero " "for auto." msgstr "" "Speed for printing top solid layers (it only applies to the uppermost " "external layers and not to their internal solid layers). You may want to " "slow down this to get a nicer surface finish. This can be expressed as a " "percentage (for example: 80%) over the solid infill speed above. Set to zero " "for auto." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1640 msgid "Top" msgstr "Top" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1642 msgid "Number of solid layers to generate on top surfaces." msgstr "Number of solid layers to generate on top surfaces." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1644 msgid "Top solid layers" msgstr "Top solid layers" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1649 msgid "Travel" msgstr "Travel" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1650 msgid "Speed for travel moves (jumps between distant extrusion points)." msgstr "Speed for travel moves (jumps between distant extrusion points)." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1658 msgid "Use firmware retraction" msgstr "Use firmware retraction" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1659 msgid "" "This experimental setting uses G10 and G11 commands to have the firmware " "handle the retraction. This is only supported in recent Marlin." msgstr "" "This experimental setting uses G10 and G11 commands to have the firmware " "handle the retraction. This is only supported in recent Marlin." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1665 msgid "Use relative E distances" msgstr "Use relative E distances" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1666 msgid "" "If your firmware requires relative E values, check this, otherwise leave it " "unchecked. Most firmwares use absolute values." msgstr "" "If your firmware requires relative E values, check this, otherwise leave it " "unchecked. Most firmwares use absolute values." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1672 msgid "Use volumetric E" msgstr "Use volumetric E" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1673 msgid "" "This experimental setting uses outputs the E values in cubic millimeters " "instead of linear millimeters. If your firmware doesn't already know " "filament diameter(s), you can put commands like 'M200 D[filament_diameter_0] " "T0' in your start G-code in order to turn volumetric mode on and use the " "filament diameter associated to the filament selected in Slic3r. This is " "only supported in recent Marlin." msgstr "" "This experimental setting uses outputs the E values in cubic millimeters " "instead of linear millimeters. If your firmware doesn't already know " "filament diameter(s), you can put commands like 'M200 D[filament_diameter_0] " "T0' in your start G-code in order to turn volumetric mode on and use the " "filament diameter associated to the filament selected in Slic3r. This is " "only supported in recent Marlin." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1683 msgid "Enable variable layer height feature" msgstr "Enable variable layer height feature" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1684 msgid "" "Some printers or printer setups may have difficulties printing with a " "variable layer height. Enabled by default." msgstr "" "Some printers or printer setups may have difficulties printing with a " "variable layer height. Enabled by default." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1690 msgid "Wipe while retracting" msgstr "Wipe while retracting" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1691 msgid "" "This flag will move the nozzle while retracting to minimize the possible " "blob on leaky extruders." msgstr "" "This flag will move the nozzle while retracting to minimize the possible " "blob on leaky extruders." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1698 msgid "" "Multi material printers may need to prime or purge extruders on tool " "changes. Extrude the excess material into the wipe tower." msgstr "" "Multi material printers may need to prime or purge extruders on tool " "changes. Extrude the excess material into the wipe tower." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1704 msgid "Position X" msgstr "Position X" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1705 msgid "X coordinate of the left front corner of a wipe tower" msgstr "X coordinate of the left front corner of a wipe tower" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1711 msgid "Position Y" msgstr "Position Y" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1712 msgid "Y coordinate of the left front corner of a wipe tower" msgstr "Y coordinate of the left front corner of a wipe tower" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1718 msgid "Width" msgstr "Width" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1719 msgid "Width of a wipe tower" msgstr "Width of a wipe tower" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1725 msgid "Per color change depth" msgstr "Per color change depth" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1726 msgid "" "Depth of a wipe color per color change. For N colors, there will be maximum " "(N-1) tool switches performed, therefore the total depth of the wipe tower " "will be (N-1) times this value." msgstr "" "Depth of a wipe color per color change. For N colors, there will be maximum " "(N-1) tool switches performed, therefore the total depth of the wipe tower " "will be (N-1) times this value." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1734 msgid "XY Size Compensation" msgstr "XY Size Compensation" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1736 msgid "" "The object will be grown/shrunk in the XY plane by the configured value " "(negative = inwards, positive = outwards). This might be useful for fine-" "tuning hole sizes." msgstr "" "The object will be grown/shrunk in the XY plane by the configured value " "(negative = inwards, positive = outwards). This might be useful for fine-" "tuning hole sizes." #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1744 msgid "Z offset" msgstr "Z offset" #: C:\src\Slic3r\xs\src\libslic3r\PrintConfig.cpp:1745 msgid "" "This value will be added (or subtracted) from all the Z coordinates in the " "output G-code. It is used to compensate for bad Z endstop position: for " "example, if your endstop zero actually leaves the nozzle 0.3mm far from the " "print bed, set this to -0.3 (or fix your endstop)." msgstr "" "This value will be added (or subtracted) from all the Z coordinates in the " "output G-code. It is used to compensate for bad Z endstop position: for " "example, if your endstop zero actually leaves the nozzle 0.3mm far from the " "print bed, set this to -0.3 (or fix your endstop)." #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:39 msgid "Shape" msgstr "Shape" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:46 msgid "Rectangular" msgstr "Rectangular" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:62 msgid "Circular" msgstr "Circular" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:75 msgid "Load shape from STL..." msgstr "Load shape from STL..." #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:120 msgid "Settings" msgstr "Settings" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:298 msgid "Choose a file to import bed shape from (STL/OBJ/AMF/PRUSA):" msgstr "Choose a file to import bed shape from (STL/OBJ/AMF/PRUSA):" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:315 msgid "Error! " msgstr "Error! " #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:324 msgid "The selected file contains no geometry." msgstr "The selected file contains no geometry." #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:328 msgid "" "The selected file contains several disjoint areas. This is not supported." msgstr "" "The selected file contains several disjoint areas. This is not supported." #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.hpp:42 msgid "Bed Shape" msgstr "Bed Shape" #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:468 msgid "Error" msgstr "Error" #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:473 msgid "Notice" msgstr "Notice" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:50 msgid "Save current " msgstr "Save current " #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:51 msgid "Delete this preset" msgstr "Delete this preset" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:330 msgid "Horizontal shells" msgstr "Horizontal shells" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:336 msgid "Quality (slower slicing)" msgstr "Quality (slower slicing)" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:353 msgid "Reducing printing time" msgstr "Reducing printing time" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:365 msgid "Skirt and brim" msgstr "Skirt and brim" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:381 msgid "Raft" msgstr "Raft" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:412 msgid "Speed for non-print moves" msgstr "Speed for non-print moves" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:415 msgid "Modifiers" msgstr "Modifiers" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:418 msgid "Acceleration control (advanced)" msgstr "Acceleration control (advanced)" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:425 msgid "Autospeed (advanced)" msgstr "Autospeed (advanced)" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:431 msgid "Multiple Extruders" msgstr "Multiple Extruders" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:439 msgid "Ooze prevention" msgstr "Ooze prevention" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:464 msgid "Overlap" msgstr "Overlap" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:467 msgid "Flow" msgstr "Flow" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:470 msgid "Other" msgstr "Other" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:477 msgid "Output options" msgstr "Output options" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:478 msgid "Sequential printing" msgstr "Sequential printing" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:501 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:502 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:858 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:859 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1155 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1156 msgid "Notes" msgstr "Notes" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:508 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:866 msgid "Dependencies" msgstr "Dependencies" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:509 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:867 msgid "Profile dependencies" msgstr "Profile dependencies" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:799 msgid "Bed" msgstr "Bed" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:804 msgid "Cooling" msgstr "Cooling" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:816 msgid "Fan settings" msgstr "Fan settings" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:835 msgid "Print speed override" msgstr "Print speed override" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:845 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1118 msgid "Custom G-code" msgstr "Custom G-code" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:936 msgid "General" msgstr "General" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:937 msgid "Size and coordinates" msgstr "Size and coordinates" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:941 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1642 msgid "Set" msgstr "Set" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:961 msgid "Capabilities" msgstr "Capabilities" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1003 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1071 msgid "Test" msgstr "Test" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1016 msgid "Connection to printer works correctly." msgstr "Connection to printer works correctly." #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1016 msgid "Success!" msgstr "Success!" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1019 msgid "Connection failed." msgstr "Connection failed." #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1031 msgid "OctoPrint upload" msgstr "OctoPrint upload" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1034 msgid "Browse" msgstr "Browse" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1046 msgid "Button BROWSE was clicked!" msgstr "Button BROWSE was clicked!" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1081 msgid "Button TEST was clicked!" msgstr "Button TEST was clicked!" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1109 msgid "Firmware" msgstr "Firmware" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1191 msgid "Layer height limits" msgstr "Layer height limits" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1196 msgid "Position (for multi-extruder printers)" msgstr "Position (for multi-extruder printers)" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1215 msgid "" "Retraction when tool is disabled (advanced settings for multi-extruder " "setups)" msgstr "" "Retraction when tool is disabled (advanced settings for multi-extruder " "setups)" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1219 msgid "Preview" msgstr "Preview" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1310 msgid "" "The Wipe option is not available when using the Firmware Retraction mode.\n" "\n" "Shall I disable it in order to enable Firmware Retraction?" msgstr "" "The Wipe option is not available when using the Firmware Retraction mode.\n" "\n" "Shall I disable it in order to enable Firmware Retraction?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1558 msgid "The supplied name is empty. It can't be saved." msgstr "The supplied name is empty. It can't be saved." #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1569 msgid "Something is wrong. It can't be saved." msgstr "Something is wrong. It can't be saved." #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1586 msgid "remove" msgstr "remove" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1586 msgid "delete" msgstr "delete" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1587 msgid "Are you sure you want to " msgstr "Are you sure you want to " #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1587 msgid " the selected preset?" msgstr " the selected preset?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1588 msgid "Remove" msgstr "Remove" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1588 msgid "Delete" msgstr "Delete" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1589 msgid " Preset" msgstr " Preset" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1641 msgid "All" msgstr "All" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1672 msgid "Select the printers this profile is compatible with." msgstr "Select the printers this profile is compatible with." #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1756 msgid "Save " msgstr "Save " #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1756 msgid " as:" msgstr " as:" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1790 msgid "" "The supplied name is not valid; the following characters are not allowed:" msgstr "" "The supplied name is not valid; the following characters are not allowed:" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1793 msgid "The supplied name is not available." msgstr "The supplied name is not available." #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.hpp:182 msgid "Print Settings" msgstr "Print Settings" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.hpp:202 msgid "Filament Settings" msgstr "Filament Settings" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.hpp:248 msgid "Save preset" msgstr "Save preset" #: c:\src\Slic3r\xs\src\slic3r\GUI\Field.cpp:35 msgid "default" msgstr "default" #: c:\src\Slic3r\xs\src\slic3r\GUI\BedShapeDialog.cpp:71 msgid "Custom" msgstr "Custom" #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:212 msgid "Array of language names and identifiers should have the same size." msgstr "Array of language names and identifiers should have the same size." #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:223 msgid "Select the language" msgstr "Select the language" #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:223 msgid "Language" msgstr "Language" #: c:\src\Slic3r\xs\src\slic3r\GUI\GUI.cpp:321 msgid "Change Application Language" msgstr "Change Application Language" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:314 msgid "Layers and perimeters" msgstr "Layers and perimeters" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:319 msgid "Vertical shells" msgstr "Vertical shells" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:366 msgid "Skirt" msgstr "Skirt" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:372 msgid "Brim" msgstr "Brim" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:385 msgid "Options for support material and raft" msgstr "Options for support material and raft" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:400 msgid "Speed for print moves" msgstr "Speed for print moves" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:443 msgid "Wipe tower" msgstr "Wipe tower" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:454 msgid "Extrusion width" msgstr "Extrusion width" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:480 msgid "Extruder clearance (mm)" msgstr "Extruder clearance (mm)" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:489 msgid "Output file" msgstr "Output file" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:534 #, c-format msgid "" "The Spiral Vase mode requires:\n" "- one perimeter\n" "- no top solid layers\n" "- 0% fill density\n" "- no support material\n" "- no ensure_vertical_shell_thickness\n" "\n" "Shall I adjust those settings in order to enable Spiral Vase?" msgstr "" "The Spiral Vase mode requires:\n" "- one perimeter\n" "- no top solid layers\n" "- 0% fill density\n" "- no support material\n" "- no ensure_vertical_shell_thickness\n" "\n" "Shall I adjust those settings in order to enable Spiral Vase?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:541 msgid "Spiral Vase" msgstr "Spiral Vase" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:560 msgid "" "The Wipe Tower currently supports only:\n" "- first layer height 0.2mm\n" "- layer height from 0.15mm to 0.35mm\n" "\n" "Shall I adjust those settings in order to enable the Wipe Tower?" msgstr "" "The Wipe Tower currently supports only:\n" "- first layer height 0.2mm\n" "- layer height from 0.15mm to 0.35mm\n" "\n" "Shall I adjust those settings in order to enable the Wipe Tower?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:564 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:585 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:602 msgid "Wipe Tower" msgstr "Wipe tower" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:581 msgid "" "The Wipe Tower currently supports the non-soluble supports only\n" "if they are printed with the current extruder without triggering a tool " "change.\n" "(both support_material_extruder and support_material_interface_extruder need " "to be set to 0).\n" "\n" "Shall I adjust those settings in order to enable the Wipe Tower?" msgstr "" "The Wipe Tower currently supports the non-soluble supports only\n" "if they are printed with the current extruder without triggering a tool " "change.\n" "(both support_material_extruder and support_material_interface_extruder need " "to be set to 0).\n" "\n" "Shall I adjust those settings in order to enable the Wipe Tower?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:599 msgid "" "For the Wipe Tower to work with the soluble supports, the support layers\n" "need to be synchronized with the object layers.\n" "\n" "Shall I synchronize support layers in order to enable the Wipe Tower?" msgstr "" "For the Wipe Tower to work with the soluble supports, the support layers\n" "need to be synchronized with the object layers.\n" "\n" "Shall I synchronize support layers in order to enable the Wipe Tower?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:617 msgid "" "Supports work better, if the following feature is enabled:\n" "- Detect bridging perimeters\n" "\n" "Shall I adjust those settings for supports?" msgstr "" "Supports work better, if the following feature is enabled:\n" "- Detect bridging perimeters\n" "\n" "Shall I adjust those settings for supports?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:620 msgid "Support Generator" msgstr "Support Generator" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:662 msgid "The " msgstr "The " #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:662 #, c-format msgid "" " infill pattern is not supposed to work at 100% density.\n" "\n" "Shall I switch to rectilinear fill pattern?" msgstr "" " infill pattern is not supposed to work at 100% density.\n" "\n" "Shall I switch to rectilinear fill pattern?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:785 #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:786 msgid "Filament" msgstr "Filament" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:817 msgid "Fan speed" msgstr "Fan speed" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:825 msgid "Cooling thresholds" msgstr "Cooling thresholds" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:831 msgid "Filament properties" msgstr "Filament properties" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:988 msgid "USB/Serial connection" msgstr "USB/Serial connection" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:994 msgid "Rescan serial ports" msgstr "Rescan serial ports" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1149 msgid "Between objects G-code (for sequential printing)" msgstr "Between objects G-code (for sequential printing)" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1185 msgid "Extruder " msgstr "Extruder " #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1199 msgid "Retraction" msgstr "Retraction" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1202 msgid "Only lift Z" msgstr "Only lift Z" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1312 msgid "Firmware Retraction" msgstr "Firmware Retraction" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1467 msgid "Default " msgstr "Default " #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1467 msgid " preset" msgstr " preset" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1468 msgid " preset\n" msgstr " preset\n" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1486 msgid "" "\n" "\n" "is not compatible with printer\n" msgstr "" "\n" "\n" "is not compatible with printer\n" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1486 msgid "" "\n" "\n" "and it has the following unsaved changes:" msgstr "" "\n" "\n" "and it has the following unsaved changes:" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1487 msgid "" "\n" "\n" "has the following unsaved changes:" msgstr "" "\n" "\n" "has the following unsaved changes:" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1489 msgid "" "\n" "\n" "Discard changes and continue anyway?" msgstr "" "\n" "\n" "Discard changes and continue anyway?" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.cpp:1490 msgid "Unsaved Changes" msgstr "Unsaved Changes" #: c:\src\Slic3r\xs\src\slic3r\GUI\Tab.hpp:228 msgid "Printer Settings" msgstr "Printer Settings"