| .. |
|
ExtrusionPath
|
Remove XXX from dependencies
|
2012-04-16 14:03:36 +02:00 |
|
Fill
|
Remove Rectilinear2 infill
|
2012-04-16 14:06:52 +02:00 |
|
Format
|
Remove XXX from dependencies
|
2012-04-16 14:03:36 +02:00 |
|
Geometry
|
Bugfix: some holes were filled. #291
|
2012-04-02 11:40:12 +02:00 |
|
GUI
|
Don't ask for confirmation (and reset values) when duplicate is set to 'no'. #311
|
2012-04-14 15:37:28 +02:00 |
|
TriangleMesh
|
New slicing algorithm based on a topological approach rather than numeric. It should be much more robust
|
2012-02-18 20:36:14 +01:00 |
|
Config.pm
|
Rename $Slic3r::resolution to $Slic3r::scaling_factor
|
2012-04-16 14:05:38 +02:00 |
|
ExPolygon.pm
|
Rename $Slic3r::resolution to $Slic3r::scaling_factor
|
2012-04-16 14:05:38 +02:00 |
|
Extruder.pm
|
Increase the flow rate for support material
|
2012-04-16 14:18:07 +02:00 |
|
ExtrusionLoop.pm
|
Remove XXX from dependencies
|
2012-04-16 14:03:36 +02:00 |
|
ExtrusionPath.pm
|
Rename $Slic3r::resolution to $Slic3r::scaling_factor
|
2012-04-16 14:05:38 +02:00 |
|
Fill.pm
|
Remove Rectilinear2 infill
|
2012-04-16 14:06:52 +02:00 |
|
Geometry.pm
|
Rename $Slic3r::resolution to $Slic3r::scaling_factor
|
2012-04-16 14:05:38 +02:00 |
|
GUI.pm
|
New icon
|
2012-04-07 20:45:59 +02:00 |
|
Layer.pm
|
Rename $Slic3r::resolution to $Slic3r::scaling_factor
|
2012-04-16 14:05:38 +02:00 |
|
Line.pm
|
Huge speed Boost (pun intended). Also fixes a problem where infill was escaping perimeters sometimes (#305).
|
2012-04-09 11:04:32 +02:00 |
|
Perimeter.pm
|
Remove XXX from dependencies
|
2012-04-16 14:03:36 +02:00 |
|
Point.pm
|
Honeycomb infill. #300
|
2012-04-16 11:55:14 +02:00 |
|
Polygon.pm
|
Rename $Slic3r::resolution to $Slic3r::scaling_factor
|
2012-04-16 14:05:38 +02:00 |
|
Polyline.pm
|
Remove XXX from dependencies
|
2012-04-16 14:03:36 +02:00 |
|
Print.pm
|
Rename $Slic3r::resolution to $Slic3r::scaling_factor
|
2012-04-16 14:05:38 +02:00 |
|
Skein.pm
|
Remove XXX from dependencies
|
2012-04-16 14:03:36 +02:00 |
|
Surface.pm
|
Bugfix: bad syntax in last commit. #202
|
2012-02-13 18:02:54 +01:00 |
|
SVG.pm
|
Rename $Slic3r::resolution to $Slic3r::scaling_factor
|
2012-04-16 14:05:38 +02:00 |
|
TriangleMesh.pm
|
Remove XXX from dependencies
|
2012-04-16 14:03:36 +02:00 |
