82 lines
2.9 KiB
Perl
82 lines
2.9 KiB
Perl
use Test::More tests => 6;
|
|
use strict;
|
|
use warnings;
|
|
|
|
BEGIN {
|
|
use FindBin;
|
|
use lib "$FindBin::Bin/../lib";
|
|
use local::lib "$FindBin::Bin/../local-lib";
|
|
}
|
|
|
|
use List::Util qw(first sum);
|
|
use Slic3r;
|
|
use Slic3r::Geometry qw(scale PI);
|
|
use Slic3r::Test;
|
|
|
|
{
|
|
my $config = Slic3r::Config->new_from_defaults;
|
|
$config->set('skirts', 1);
|
|
$config->set('brim_width', 2);
|
|
$config->set('perimeters', 3);
|
|
$config->set('fill_density', 0.4);
|
|
$config->set('bottom_solid_layers', 1);
|
|
$config->set('first_layer_extrusion_width', 2);
|
|
$config->set('first_layer_height', '100%');
|
|
|
|
my $print = Slic3r::Test::init_print('20mm_cube', config => $config);
|
|
my @E_per_mm = ();
|
|
Slic3r::GCode::Reader->new->parse(my $gcode = Slic3r::Test::gcode($print), sub {
|
|
my ($self, $cmd, $args, $info) = @_;
|
|
|
|
if ($self->Z == $config->layer_height) { # only consider first layer
|
|
if ($info->{extruding} && $info->{dist_XY} > 0) {
|
|
push @E_per_mm, $info->{dist_E} / $info->{dist_XY};
|
|
}
|
|
}
|
|
});
|
|
my $E_per_mm_avg = sum(@E_per_mm) / @E_per_mm;
|
|
# allow some tolerance because solid rectilinear infill might be adjusted/stretched
|
|
ok !(defined first { abs($_ - $E_per_mm_avg) > 0.015 } @E_per_mm),
|
|
'first_layer_extrusion_width applies to everything on first layer';
|
|
}
|
|
|
|
{
|
|
my $config = Slic3r::Config->new_from_defaults;
|
|
$config->set('bridge_speed', 99);
|
|
$config->set('bridge_flow_ratio', 1);
|
|
$config->set('cooling', [ 0 ]); # to prevent speeds from being altered
|
|
$config->set('first_layer_speed', '100%'); # to prevent speeds from being altered
|
|
|
|
my $test = sub {
|
|
my $print = Slic3r::Test::init_print('overhang', config => $config);
|
|
my @E_per_mm = ();
|
|
Slic3r::GCode::Reader->new->parse(my $gcode = Slic3r::Test::gcode($print), sub {
|
|
my ($self, $cmd, $args, $info) = @_;
|
|
|
|
if ($info->{extruding} && $info->{dist_XY} > 0) {
|
|
if (($args->{F} // $self->F) == $config->bridge_speed*60) {
|
|
push @E_per_mm, $info->{dist_E} / $info->{dist_XY};
|
|
}
|
|
}
|
|
});
|
|
my $expected_mm3_per_mm = ($config->nozzle_diameter->[0]**2) * PI/4 * $config->bridge_flow_ratio;
|
|
my $expected_E_per_mm = $expected_mm3_per_mm / ((($config->filament_diameter->[0]/2)**2)*PI);
|
|
ok !(defined first { abs($_ - $expected_E_per_mm) > 0.01 } @E_per_mm),
|
|
'expected flow when using bridge_flow_ratio = ' . $config->bridge_flow_ratio;
|
|
};
|
|
|
|
$config->set('bridge_flow_ratio', 0.5);
|
|
$test->();
|
|
$config->set('bridge_flow_ratio', 2);
|
|
$test->();
|
|
$config->set('extrusion_width', 0.4);
|
|
$config->set('bridge_flow_ratio', 1);
|
|
$test->();
|
|
$config->set('bridge_flow_ratio', 0.5);
|
|
$test->();
|
|
$config->set('bridge_flow_ratio', 2);
|
|
$test->();
|
|
}
|
|
|
|
__END__
|