pią, 31 gru 2021, 13:30:40 CET

filament/Devil Design PLA_.ini

@@ -0,0 +1,57 @@
+# generated by PrusaSlicer 2.4.0+linux-x64-GTK3 on 2021-12-29 at 20:52:58 UTC
+bed_temperature = 60
+bridge_fan_speed = 100
+compatible_printers = 
+compatible_printers_condition = 
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 1
+end_filament_gcode = "; Filament-specific end gcode"
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 100
+filament_colour = #FF8000
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 20.99
+filament_density = 1.24
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 15
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_spool_weight = 250
+filament_toolchange_delay = 0
+filament_type = PLA
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = Devil Design
+filament_wipe = nil
+first_layer_bed_temperature = 60
+first_layer_temperature = 215
+full_fan_speed_layer = 4
+inherits = Devil Design PLA
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 15
+slowdown_below_layer_time = 15
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.05{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0"
+temperature = 210

printer/Original Prusa i3 MK3S & MK3S+ MMU2S_.ini

@@ -0,0 +1,78 @@
+# generated by PrusaSlicer 2.4.0+linux-x64-GTK3 on 2021-12-30 at 10:50:50 UTC
+bed_custom_model = 
+bed_custom_texture = 
+bed_shape = 0x0,250x0,250x210,0x210
+before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n
+between_objects_gcode = 
+color_change_gcode = M600\nG1 E0.4 F1500 ; prime after color change
+cooling_tube_length = 20
+cooling_tube_retraction = 40
+default_filament_profile = "Prusament PLA @MMU2"
+default_print_profile = 0.15mm QUALITY @MK3
+deretract_speed = 0,0,0,0,0
+end_gcode = ; Lift print head a bit\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} ; Move print head up\n{if has_wipe_tower}\nG1 E-15 F3000\n{else}\nG1 X0 Y210 F7200\nG1 E2 F5000\nG1 E2 F5500\nG1 E2 F6000\nG1 E-15 F5800\nG1 E-20 F5500\nG1 E10 F3000\nG1 E-10 F3100\nG1 E10 F3150\nG1 E-10 F3250\nG1 E10 F3300\n{endif}\n\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\n\n; Unload filament\nM702 C\n\nG4 ; wait\nM221 S100 ; reset flow\nM900 K0 ; reset LA\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3|SOLUBLE|@0.25 nozzle MK3).*/}M907 E538 ; reset extruder motor current{endif}\nM104 S0 ; turn off temperature\nG1 X0 Y210 F3000 ; home X axis\nM84 ; disable motors\n
+extra_loading_move = -25
+extruder_colour = #FF8000;#DB5182;#3EC0FF;#FF4F4F;#000000
+extruder_offset = 0x0,0x0,0x0,0x0,0x0
+gcode_flavor = marlin
+high_current_on_filament_swap = 0
+host_type = octoprint
+inherits = Original Prusa i3 MK3S & MK3S+ MMU2S
+layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
+machine_limits_usage = emit_to_gcode
+machine_max_acceleration_e = 8000,8000
+machine_max_acceleration_extruding = 1250,1250
+machine_max_acceleration_retracting = 1250,1250
+machine_max_acceleration_travel = 1500,1250
+machine_max_acceleration_x = 1000,960
+machine_max_acceleration_y = 1000,960
+machine_max_acceleration_z = 200,200
+machine_max_feedrate_e = 120,120
+machine_max_feedrate_x = 200,100
+machine_max_feedrate_y = 200,100
+machine_max_feedrate_z = 12,12
+machine_max_jerk_e = 4.5,4.5
+machine_max_jerk_x = 8,8
+machine_max_jerk_y = 8,8
+machine_max_jerk_z = 0.4,0.4
+machine_min_extruding_rate = 0,0
+machine_min_travel_rate = 0,0
+max_layer_height = 0.25,0.25,0.25,0.25,0.25
+max_print_height = 210
+min_layer_height = 0.07,0.07,0.07,0.07,0.07
+nozzle_diameter = 0.4,0.4,0.4,0.4,0.4
+parking_pos_retraction = 85
+pause_print_gcode = M601
+print_host = 
+printer_model = MK3SMMU2S
+printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK3\n
+printer_settings_id = 
+printer_technology = FFF
+printer_variant = 0.4
+printer_vendor = 
+printhost_apikey = 
+printhost_cafile = 
+remaining_times = 1
+retract_before_travel = 1,1,1,1,1
+retract_before_wipe = 0%,0%,0%,0%,0%
+retract_layer_change = 1,1,1,1,1
+retract_length = 0.8,0.8,0.8,0.8,0.8
+retract_length_toolchange = 0,0,0,0,0
+retract_lift = 0.4,0.4,0.4,0.4,0.4
+retract_lift_above = 0,0,0,0,0
+retract_lift_below = 209,209,209,209,209
+retract_restart_extra = 0,0,0,0,0
+retract_restart_extra_toolchange = 0,0,0,0,0
+retract_speed = 35,35,35,35,35
+silent_mode = 1
+single_extruder_multi_material = 1
+start_gcode = M862.3 P "[printer_model]" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.10.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n; Send the filament type to the MMU2.0 unit.\n; E stands for extruder number, F stands for filament type (0: default; 1:flex; 2: PVA)\nM403 E0 F{"" + ((filament_type[0]=="FLEX") ? 1 : ((filament_type[0]=="PVA") ? 2 : 0))}\nM403 E1 F{"" + ((filament_type[1]=="FLEX") ? 1 : ((filament_type[1]=="PVA") ? 2 : 0))}\nM403 E2 F{"" + ((filament_type[2]=="FLEX") ? 1 : ((filament_type[2]=="PVA") ? 2 : 0))}\nM403 E3 F{"" + ((filament_type[3]=="FLEX") ? 1 : ((filament_type[3]=="PVA") ? 2 : 0))}\nM403 E4 F{"" + ((filament_type[4]=="FLEX") ? 1 : ((filament_type[4]=="PVA") ? 2 : 0))}\n\n{if not has_single_extruder_multi_material_priming}\n;go outside print area\nG1 Y-3 F1000\nG1 Z0.4 F1000\n; select extruder\nT[initial_tool]\n; initial load\nG1 X55 E29 F1073\nG1 X5 E29 F1800\nG1 X55 E8 F2000\nG1 Z0.3 F1000\nG92 E0\nG1 X240 E25 F2200\nG1 Y-2 F1000\nG1 X55 E25 F1400\nG1 Z0.2 F1000\nG1 X5 E4 F1000\nG92 E0\n{endif}\n\nM221 S{if layer_height<0.075}100{else}95{endif}\nG92 E0\n\n; Don't change E values below. Excessive value can damage the printer.\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3|SOLUBLE).*/}M907 E430 ; set extruder motor current{endif}\n{if print_settings_id=~/.*(SPEED @MK3|DRAFT @MK3).*/}M907 E538 ; set extruder motor current{endif}
+template_custom_gcode = 
+thumbnails = 
+toolchange_gcode = 
+use_firmware_retraction = 0
+use_relative_e_distances = 1
+use_volumetric_e = 0
+variable_layer_height = 1
+wipe = 1,1,1,1,1
+z_offset = 0

printer/Tevo Tarantula.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.3.3+linux-x64-GTK3 on 2021-08-27 at 21:41:25 UTC
+# generated by PrusaSlicer 2.4.0+linux-x64-GTK3 on 2021-12-31 at 12:23:27 UTC
 bed_custom_model = 
 bed_custom_texture = 
 bed_shape = 0x0,200x0,200x200,0x200
@@ -14,7 +14,7 @@ end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; dis
 extra_loading_move = -2
 extruder_colour = ""
 extruder_offset = 0x0
-gcode_flavor = marlin
+gcode_flavor = marlin2
 high_current_on_filament_swap = 0
 host_type = octoprint
 inherits = 
@@ -23,6 +23,7 @@ machine_limits_usage = emit_to_gcode
 machine_max_acceleration_e = 10000,5000
 machine_max_acceleration_extruding = 1500,1250
 machine_max_acceleration_retracting = 1500,1250
+machine_max_acceleration_travel = 1500,1250
 machine_max_acceleration_x = 9000,1000
 machine_max_acceleration_y = 9000,1000
 machine_max_acceleration_z = 500,200
@@ -65,7 +66,7 @@ retract_restart_extra_toolchange = 0
 retract_speed = 40
 silent_mode = 1
 single_extruder_multi_material = 0
-start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
+start_gcode = M16 "Tevo Tarantula"\nG28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
 template_custom_gcode = 
 thumbnails = 
 toolchange_gcode =