Update

filament/Fiberlogy Easy PCTG.ini

@@ -0,0 +1,75 @@
+# generated by PrusaSlicer 2.7.3 on 2024-04-05 at 07:39:17 UTC
+bed_temperature = 100
+bridge_fan_speed = 60
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*MK4.*/ and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 5
+enable_dynamic_fan_speeds = 0
+end_filament_gcode = "; Filament-specific end gcode"
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 20
+filament_colour = #FF8000
+filament_cooling_final_speed = 1
+filament_cooling_initial_speed = 2
+filament_cooling_moves = 1
+filament_cost = 20
+filament_density = 1.27
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 15
+filament_loading_speed = 14
+filament_loading_speed_start = 19
+filament_max_volumetric_speed = 10
+filament_minimal_purge_on_wipe_tower = 35
+filament_multitool_ramming = 0
+filament_multitool_ramming_flow = 10
+filament_multitool_ramming_volume = 10
+filament_notes = ""
+filament_purge_multiplier = 100%
+filament_ramming_parameters = "120 140 4.70968 4.74194 4.77419 4.80645 4.83871 4.87097 4.90323 5 5.25806 5.67742 6.29032 7.06452 7.83871 8.3871| 0.05 4.72901 0.45 4.73545 0.95 4.83226 1.45 4.88067 1.95 5.05483 2.45 5.93553 2.95 7.53556 3.45 8.6323 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = 0%
+filament_retract_layer_change = nil
+filament_retract_length = 1
+filament_retract_length_toolchange = nil
+filament_retract_lift = 0.15
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_restart_extra_toolchange = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_spool_weight = 330
+filament_stamping_distance = 0
+filament_stamping_loading_speed = 20
+filament_toolchange_delay = 0
+filament_travel_lift_before_obstacle = nil
+filament_travel_max_lift = nil
+filament_travel_ramping_lift = nil
+filament_travel_slope = nil
+filament_type = PETG
+filament_unload_time = 12
+filament_unloading_speed = 20
+filament_unloading_speed_start = 120
+filament_vendor = Fiberlogy
+filament_wipe = nil
+first_layer_bed_temperature = 100
+first_layer_temperature = 250
+full_fan_speed_layer = 5
+idle_temperature = 70
+inherits = Fiberlogy Easy PET-G @PG
+max_fan_speed = 25
+min_fan_speed = 0
+min_print_speed = 15
+overhang_fan_speed_0 = 0
+overhang_fan_speed_1 = 0
+overhang_fan_speed_2 = 0
+overhang_fan_speed_3 = 0
+slowdown_below_layer_time = 9
+start_filament_gcode = "M900 K{if nozzle_diameter[0]==0.4}0.07{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.09{elsif nozzle_diameter[0]==0.35}0.08{elsif nozzle_diameter[0]==0.6}0.04{elsif nozzle_diameter[0]==0.5}0.05{elsif nozzle_diameter[0]==0.8}0.02{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS).*/}\nM572 S{if nozzle_diameter[0]==0.4}0.055{elsif nozzle_diameter[0]==0.5}0.042{elsif nozzle_diameter[0]==0.6}0.032{elsif nozzle_diameter[0]==0.8}0.018{elsif nozzle_diameter[0]==0.25}0.18{elsif nozzle_diameter[0]==0.3}0.1{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S36 ; set heatbreak target temp"
+temperature = 250

print/QUALITY - 0.20mm.ini

@@ -1,4 +1,6 @@
-# generated by PrusaSlicer 2.5.0+linux-x64-GTK3 on 2023-01-06 at 00:14:19 UTC
+# generated by PrusaSlicer 2.7.3 on 2024-04-05 at 07:41:27 UTC
+arc_fitting = disabled
+avoid_crossing_curled_overhangs = 0
 avoid_crossing_perimeters = 0
 avoid_crossing_perimeters_max_detour = 0
 bottom_fill_pattern = monotonic
@@ -11,7 +13,6 @@ bridge_speed = 25
 brim_separation = 0.1
 brim_type = outer_only
 brim_width = 0
-clip_multipart_objects = 1
 compatible_printers = 
 compatible_printers_condition = nozzle_diameter[0]==0.4
 complete_objects = 0
@@ -19,11 +20,13 @@ default_acceleration = 1000
 dont_support_bridges = 0
 draft_shield = disabled
 elefant_foot_compensation = 0.2
-ensure_vertical_shell_thickness = 1
+enable_dynamic_overhang_speeds = 0
+external_perimeter_acceleration = 0
 external_perimeter_extrusion_width = 0.45
 external_perimeter_speed = 25
 external_perimeters_first = 0
 extra_perimeters = 0
+extra_perimeters_on_overhangs = 0
 extruder_clearance_height = 20
 extruder_clearance_radius = 45
 extrusion_width = 0.45
@@ -42,7 +45,7 @@ fuzzy_skin_thickness = 0.3
 gap_fill_enabled = 1
 gap_fill_speed = 40
 gcode_comments = 1
-gcode_label_objects = 1
+gcode_label_objects = octoprint
 gcode_resolution = 0.0125
 gcode_substitutions = 
 infill_acceleration = 1000
@@ -52,7 +55,6 @@ infill_every_layers = 1
 infill_extruder = 1
 infill_extrusion_width = 0.45
 infill_first = 0
-infill_only_where_needed = 0
 infill_overlap = 25%
 infill_speed = 80
 inherits = 0.20mm QUALITY @MK3
@@ -70,11 +72,16 @@ max_volumetric_speed = 0
 min_bead_width = 85%
 min_feature_size = 25%
 min_skirt_length = 4
+mmu_segmented_region_interlocking_depth = 0
 mmu_segmented_region_max_width = 0
 notes = 
 only_retract_when_crossing_perimeters = 0
 ooze_prevention = 0
 output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}.gcode
+overhang_speed_0 = 15
+overhang_speed_1 = 15
+overhang_speed_2 = 20
+overhang_speed_3 = 25
 overhangs = 1
 perimeter_acceleration = 800
 perimeter_extruder = 1
@@ -94,16 +101,18 @@ seam_position = aligned
 single_extruder_multi_material_priming = 0
 skirt_distance = 2
 skirt_height = 3
-skirts = 1
+skirts = 0
 slice_closing_radius = 0.049
 slicing_mode = regular
 small_perimeter_speed = 25
+solid_infill_acceleration = 0
 solid_infill_below_area = 0
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
 solid_infill_extrusion_width = 0.45
 solid_infill_speed = 80
 spiral_vase = 0
+staggered_inner_seams = 0
 standby_temperature_delta = -5
 support_material = 0
 support_material_angle = 0
@@ -130,14 +139,23 @@ support_material_synchronize_layers = 0
 support_material_threshold = 15
 support_material_with_sheath = 0
 support_material_xy_spacing = 60%
+support_tree_angle = 40
+support_tree_angle_slow = 25
+support_tree_branch_diameter = 2
+support_tree_branch_diameter_angle = 5
+support_tree_branch_diameter_double_wall = 3
+support_tree_branch_distance = 1
+support_tree_tip_diameter = 0.8
+support_tree_top_rate = 15%
 thick_bridges = 0
 thin_walls = 1
-threads = 24
 top_fill_pattern = monotonic
 top_infill_extrusion_width = 0.4
+top_solid_infill_acceleration = 0
 top_solid_infill_speed = 40
 top_solid_layers = 5
 top_solid_min_thickness = 0.7
+travel_acceleration = 0
 travel_speed = 180
 travel_speed_z = 12
 wall_distribution_count = 1
@@ -145,8 +163,13 @@ wall_transition_angle = 10
 wall_transition_filter_deviation = 25%
 wall_transition_length = 0.4
 wipe_tower = 1
+wipe_tower_acceleration = 0
 wipe_tower_bridging = 10
 wipe_tower_brim_width = 2
+wipe_tower_cone_angle = 0
+wipe_tower_extra_flow = 100%
+wipe_tower_extra_spacing = 100%
+wipe_tower_extruder = 0
 wipe_tower_no_sparse_layers = 0
 wipe_tower_rotation_angle = 0
 wipe_tower_width = 60

printer/Original Prusa MINI & MINI+ Input Shaper (SuperSpeed).ini

@@ -1,17 +1,18 @@
-# generated by PrusaSlicer 2.6.1+linux-x64-GTK3 on 2023-09-18 at 22:15:39 UTC
+# generated by PrusaSlicer 2.7.4 on 2024-04-10 at 22:59:14 UTC
 autoemit_temperature_commands = 1
 bed_custom_model = 
 bed_custom_texture = 
 bed_shape = 0x0,180x0,180x180,0x180
 before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\nM201 X{interpolate_table(extruded_weight_total, (0,4000), (1000,1700), (10000,1700))} Y{interpolate_table(extruded_weight_total, (0,4000), (1000,1700), (10000,1700))}\n{if ! spiral_vase}M74 W[extruded_weight_total]{endif}\n
 between_objects_gcode = 
+binary_gcode = 1
 color_change_gcode = M600
 cooling_tube_length = 5
 cooling_tube_retraction = 91.5
 default_filament_profile = "Prusament PLA @MINIIS"
 default_print_profile = 0.20mm SPEED @MINIIS
 deretract_speed = 40
-end_gcode = G1 E-1 F2100 ; retract\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F720 ; Move print head up{endif}\nG1 X178 Y178 F4200 ; park print head\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, max_print_height)} F720 ; Move print head further up{endif}\nG4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nM221 S100 ; reset flow\nM572 S0 ; reset PA\nM569 S1 X Y ; reset to stealthchop for X Y\nM84 ; disable motors\n; max_layer_z = [max_layer_z]
+end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F720 ; Move print head up{endif}\nG1 X170 Y170 F4200 ; park print head\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+50, max_print_height)} F720 ; Move print head further up{endif}\nG4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nM221 S100 ; reset flow\nM572 S0 ; reset PA\nM569 S1 X Y ; reset to stealthchop for X Y\nM84 ; disable motors\n; max_layer_z = [max_layer_z]
 extra_loading_move = -2
 extruder_colour = ""
 extruder_offset = 0x0
@@ -41,6 +42,7 @@ machine_min_travel_rate = 0
 max_layer_height = 0.25
 max_print_height = 180
 min_layer_height = 0.07
+multimaterial_purging = 140
 nozzle_diameter = 0.4
 parking_pos_retraction = 92
 pause_print_gcode = M601
@@ -67,11 +69,15 @@ retract_restart_extra_toolchange = 0
 retract_speed = 70
 silent_mode = 0
 single_extruder_multi_material = 0
-start_gcode = M862.3 P "MINI" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM862.5 P2 ; g-code level check\nM862.6 P"Input shaper" ; FW feature check\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S170 ; set extruder temp for bed leveling\nM140 S[first_layer_bed_temperature] ; set bed temp\nM109 R170 ; wait for bed leveling temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM569 S1 X Y ; set stealthchop for X Y\nM204 T1250 ; set travel acceleration\nG28 ; home all without mesh bed level\nG29 ; mesh bed leveling \nM104 S[first_layer_temperature] ; set extruder temp\nG92 E0\nG1 Y-2 X179 F2400\nG1 Z3 F720\nM109 S[first_layer_temperature] ; wait for extruder temp\n\n; intro line\nG1 X170 F1000\nG1 Z0.2 F720\nG1 X110 E8 F900\nG1 X40 E10 F700\nG92 E0\n\nM569 S0 X Y ; set spreadcycle for X Y\nM204 T[machine_max_acceleration_travel] ; restore travel acceleration\nM572 W0.06 ; set smooth time\nM221 S95 ; set flow\n
+start_gcode = M862.3 P "MINI" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM862.5 P2 ; g-code level check\nM862.6 P"Input shaper" ; FW feature check\nM115 U5.1.2+13478\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S170 ; set extruder temp for bed leveling\nM140 S[first_layer_bed_temperature] ; set bed temp\nM109 R170 ; wait for bed leveling temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM569 S1 X Y ; set stealthchop for X Y\nM204 T1250 ; set travel acceleration\nG28 ; home all without mesh bed level\nG29 ; mesh bed leveling \nM104 S[first_layer_temperature] ; set extruder temp\nG92 E0\n\nG1 X0 Y-2 Z3 F2400\n\nM109 S[first_layer_temperature] ; wait for extruder temp\n\n; intro line\nG1 X10 Z0.2 F1000\nG1 X70 E8 F900\nG1 X140 E10 F700\nG92 E0\n\nM569 S0 X Y ; set spreadcycle for X Y\nM204 T[machine_max_acceleration_travel] ; restore travel acceleration\nM572 W0.06 ; set smooth time\nM221 S95 ; set flow\n
 template_custom_gcode = 
-thumbnails = 16x16,220x124,200x240
+thumbnails = 16x16/QOI, 220x124/QOI, 200x240/QOI, 640x480/PNG
 thumbnails_format = QOI
 toolchange_gcode = 
+travel_lift_before_obstacle = 0
+travel_max_lift = 0
+travel_ramping_lift = 0
+travel_slope = 0
 use_firmware_retraction = 0
 use_relative_e_distances = 1
 use_volumetric_e = 0

printer/Voron_v2_350_afterburner 0.4n.ini

@@ -0,0 +1,86 @@
+# generated by PrusaSlicer 2.7.4 on 2024-04-19 at 08:59:28 UTC
+autoemit_temperature_commands = 0
+bed_custom_model = 
+bed_custom_texture = 
+bed_shape = 0x0,350x0,350x350,0x350
+before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0
+between_objects_gcode = 
+binary_gcode = 0
+color_change_gcode = M600
+cooling_tube_length = 5
+cooling_tube_retraction = 91.5
+default_filament_profile = "Basic PLA @VORON"
+default_print_profile = 0.15mm 0.4nozzle
+deretract_speed = 30
+end_gcode = print_end    ;end script from macro
+extra_loading_move = -2
+extruder_colour = #FFE3CA
+extruder_offset = 0x0
+gcode_flavor = klipper
+high_current_on_filament_swap = 0
+host_type = prusalink
+inherits = 
+layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]\nTIMELAPSE_TAKE_FRAME
+machine_limits_usage = time_estimate_only
+machine_max_acceleration_e = 10000
+machine_max_acceleration_extruding = 10000
+machine_max_acceleration_retracting = 10000
+machine_max_acceleration_travel = 1500,1250
+machine_max_acceleration_x = 15000
+machine_max_acceleration_y = 15000
+machine_max_acceleration_z = 600
+machine_max_feedrate_e = 120
+machine_max_feedrate_x = 500
+machine_max_feedrate_y = 500
+machine_max_feedrate_z = 12
+machine_max_jerk_e = 2.5
+machine_max_jerk_x = 10
+machine_max_jerk_y = 10
+machine_max_jerk_z = 0.2
+machine_min_extruding_rate = 0
+machine_min_travel_rate = 0
+max_layer_height = 0.3
+max_print_height = 330
+min_layer_height = 0.0375
+multimaterial_purging = 140
+nozzle_diameter = 0.4
+parking_pos_retraction = 92
+pause_print_gcode = M601
+print_host = 
+printer_model = Voron_v2_350_afterburner
+printer_notes = Unoffical profile.\nE3DV6
+printer_settings_id = 
+printer_technology = FFF
+printer_variant = 0.4
+printer_vendor = 
+printhost_apikey = 
+printhost_cafile = 
+remaining_times = 0
+retract_before_travel = 3
+retract_before_wipe = 0%
+retract_layer_change = 0
+retract_length = 0.4
+retract_length_toolchange = 10
+retract_lift = 0.4
+retract_lift_above = 0.2
+retract_lift_below = 500
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 50
+silent_mode = 0
+single_extruder_multi_material = 0
+start_gcode = print_start EXTRUDER=[first_layer_temperature[initial_tool]] BED=[first_layer_bed_temperature]\n; DISABLE_MESH=1
+template_custom_gcode = 
+thumbnails = 64x64/PNG, 400x300/PNG
+thumbnails_format = PNG
+toolchange_gcode = 
+travel_lift_before_obstacle = 0
+travel_max_lift = 0
+travel_ramping_lift = 0
+travel_slope = 0
+use_firmware_retraction = 0
+use_relative_e_distances = 1
+use_volumetric_e = 0
+variable_layer_height = 1
+wipe = 0
+z_offset = 0