mirror of
https://github.com/pgrondek/prusa-slicer-profiles.git
synced 2024-11-22 20:33:44 +00:00
58 lines
2.0 KiB
INI
58 lines
2.0 KiB
INI
# generated by PrusaSlicer 2.3.3+linux-x64-GTK3 on 2021-08-29 at 21:17:02 UTC
|
|
bed_temperature = 90
|
|
bridge_fan_speed = 50
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 3
|
|
end_filament_gcode = "; Filament-specific end gcode"
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #FF7800
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 80
|
|
filament_density = 1.27
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 8
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_notes = "List of manufacturers tested with standard PET print settings:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladec PETG"
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = 1
|
|
filament_retract_lift = 0.2
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 0
|
|
filament_toolchange_delay = 0
|
|
filament_type = PETG
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 85
|
|
first_layer_temperature = 230
|
|
full_fan_speed_layer = 5
|
|
inherits =
|
|
max_fan_speed = 50
|
|
min_fan_speed = 30
|
|
min_print_speed = 15
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{elsif nozzle_diameter[0]==0.6}24{else}45{endif} ; Filament gcode"
|
|
temperature = 230
|