MarlinFirmware/Marlin/src/pins/pins_AZTEEG_X3.h

/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */

/**
 * AZTEEG_X3 Arduino Mega with RAMPS v1.4 pin assignments
 */

#ifndef __AVR_ATmega2560__
  #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"
#endif

#if HOTENDS > 2 || E_STEPPERS > 2
  #error "Azteeg X3 supports up to 2 hotends / E-steppers. Comment out this line to continue."
#endif

#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT)
  #define CASE_LIGHT_PIN    6   // Define before RAMPS pins include
#endif
#define BOARD_NAME "Azteeg X3"

//
// Servos
//
#define SERVO0_PIN         44   // SERVO1 port
#define SERVO1_PIN         55   // SERVO2 port

#include "pins_RAMPS_13.h"

//
// LCD / Controller
//
#undef STAT_LED_RED_PIN
#undef STAT_LED_BLUE_PIN

#if ANY(VIKI2, miniVIKI)

  #undef DOGLCD_A0
  #undef DOGLCD_CS
  #undef BTN_ENC
  #define DOGLCD_A0         31
  #define DOGLCD_CS         32
  #define BTN_ENC           12

  #define STAT_LED_RED_PIN  64
  #define STAT_LED_BLUE_PIN 63

#else

  #define STAT_LED_RED_PIN   6
  #define STAT_LED_BLUE_PIN 11

#endif

//
// Misc
//
#if ENABLED(CASE_LIGHT_ENABLE) && PIN_EXISTS(CASE_LIGHT, STAT_LED_RED) && STAT_LED_RED_PIN == CASE_LIGHT_PIN
  #undef STAT_LED_RED_PIN
#endif

//
// M3/M4/M5 - Spindle/Laser Control
//
#undef SPINDLE_LASER_PWM_PIN    // Definitions in pins_RAMPS.h are no good with the AzteegX3 board
#undef SPINDLE_LASER_ENA_PIN
#undef SPINDLE_DIR_PIN

#if ENABLED(SPINDLE_LASER_ENABLE)
  #undef SDA                       // use EXP3 header
  #undef SCL
  #if SERVO0_PIN == 7
    #undef SERVO0_PIN
    #define SERVO0_PIN     11
  #endif
  #define SPINDLE_LASER_PWM_PIN     7   // MUST BE HARDWARE PWM
  #define SPINDLE_LASER_ENA_PIN    20   // Pin should have a pullup!
  #define SPINDLE_DIR_PIN          21
#endif
Further cleanup of comments, partial Doxygen-style Following up on #3231 2016-03-25 06:19:46 +00:00			`/**`
Added gplv3 header to all Marlin files 2016-03-24 18:01:20 +00:00			`* Marlin 3D Printer Firmware`
Update copyright in headers 2019-02-12 21:06:53 +00:00			`* Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]`
Added gplv3 header to all Marlin files 2016-03-24 18:01:20 +00:00			`*`
			`* Based on Sprinter and grbl.`
			`* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm`
			`*`
			`* This program is free software: you can redistribute it and/or modify`
			`* it under the terms of the GNU General Public License as published by`
			`* the Free Software Foundation, either version 3 of the License, or`
			`* (at your option) any later version.`
			`*`
			`* This program is distributed in the hope that it will be useful,`
			`* but WITHOUT ANY WARRANTY; without even the implied warranty of`
			`* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the`
			`* GNU General Public License for more details.`
			`*`
			`* You should have received a copy of the GNU General Public License`
			`* along with this program. If not, see <http://www.gnu.org/licenses/>.`
			`*`
			`*/`

Azteeg X3 overrides too 2015-02-20 01:28:38 +00:00			`/**`
Base RAMPS-like boards on RAMPS 1.4 2016-02-29 07:13:50 +00:00			`* AZTEEG_X3 Arduino Mega with RAMPS v1.4 pin assignments`
Azteeg X3 overrides too 2015-02-20 01:28:38 +00:00			`*/`

SPINDLE/LASER pins changes 2017-04-07 18:52:21 +00:00			`#ifndef __AVR_ATmega2560__`
Extend pins errors to include the processor 2018-11-09 03:57:15 +00:00			`#error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"`
SPINDLE/LASER pins changes 2017-04-07 18:52:21 +00:00			`#endif`

Patch pins files hotends/e-steppers sanity check 2017-04-06 22:15:09 +00:00			`#if HOTENDS > 2 \|\| E_STEPPERS > 2`
			`#error "Azteeg X3 supports up to 2 hotends / E-steppers. Comment out this line to continue."`
Consolidate setting of RAMPS High Voltage PWM outputs 2016-07-29 23:13:19 +00:00			`#endif`

Apply spacing in pins files 2018-03-28 17:51:59 +00:00			`#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT)`
			`#define CASE_LIGHT_PIN 6 // Define before RAMPS pins include`
SPINDLE/LASER pins changes 2017-04-07 18:52:21 +00:00			`#endif`
Fix case light logic on Azteeg_X3 boards. 2017-06-01 17:33:24 +00:00			`#define BOARD_NAME "Azteeg X3"`
SPINDLE/LASER pins changes 2017-04-07 18:52:21 +00:00
Follow-up the PR #5087 (Fixed SERVO pins on Azteeg X3), etc ・Add header ・Adjust spacing 2016-10-26 21:46:03 +00:00			`//`
			`// Servos`
			`//`
Apply spacing in pins files 2018-03-28 17:51:59 +00:00			`#define SERVO0_PIN 44 // SERVO1 port`
			`#define SERVO1_PIN 55 // SERVO2 port`
Fixed SERVO pins on Azteeg X3 2016-10-25 21:11:26 +00:00
Use limit switch overrides 2019-06-06 02:32:10 +00:00			`#include "pins_RAMPS_13.h"`

Follow-up the PR #4955, etc ・More ANALOG NUMBERING to Analog Input ・Add comment header to all the section of all the pins files ・Sort sections as follows: 1. Some special definitions (USBCON, LARGE_FLASH, etc) 2. Servos 3. Limit Switches 4. Z Probe 5. Steppers 6. Temperature Sensors 7. Heaters / Fans 8. Misc. Functions 9. LCD / Controller ・Move MAX6675_SS into "Temperature Sensors" section ・Adjust spacing 2016-10-08 20:27:04 +00:00			`//`
			`// LCD / Controller`
			`//`
Modernize configs 2017-10-09 21:18:10 +00:00			`#undef STAT_LED_RED_PIN`
			`#undef STAT_LED_BLUE_PIN`

Extended condition macros (#13419) Allow `ENABLED`, `DISABLED`, `PIN_EXISTS`, and `BUTTON_EXISTS` to take multiple arguments. Also add: - Alias `ANY(...)` for `!DISABLED(...)` - Alias `ANY_PIN(...)` for `PIN_EXISTS(a) \|\| PIN_EXISTS(b) ...` - Alias `EITHER(A,B)` for `ANY(...)` - Alias `ALL(...)` and `BOTH(A,B)` for `ENABLED(...)` - `NONE(...)` for `DISABLED(...)` 2019-03-17 04:43:06 +00:00			`#if ANY(VIKI2, miniVIKI)`
Overridable Options - Part 4 (PR#2556) Apply `ENABLED` / `DISABLED` / `HAS_SERVOS` macros to pins files. 2015-07-31 05:11:19 +00:00
Support for VIKI2 in RAMPS and derivatives 2016-06-29 01:11:32 +00:00			`#undef DOGLCD_A0`
			`#undef DOGLCD_CS`
			`#undef BTN_ENC`
In for a penny, in for a pound 2015-07-31 14:36:20 +00:00			`#define DOGLCD_A0 31`
			`#define DOGLCD_CS 32`
Support for VIKI2 in RAMPS and derivatives 2016-06-29 01:11:32 +00:00			`#define BTN_ENC 12`
In for a penny, in for a pound 2015-07-31 14:36:20 +00:00
Always define status LED pins 2016-09-24 21:26:41 +00:00			`#define STAT_LED_RED_PIN 64`
			`#define STAT_LED_BLUE_PIN 63`
Overridable Options - Part 4 (PR#2556) Apply `ENABLED` / `DISABLED` / `HAS_SERVOS` macros to pins files. 2015-07-31 05:11:19 +00:00
Always define status LED pins 2016-09-24 21:26:41 +00:00			`#else`
Overridable Options - Part 4 (PR#2556) Apply `ENABLED` / `DISABLED` / `HAS_SERVOS` macros to pins files. 2015-07-31 05:11:19 +00:00
Always define status LED pins 2016-09-24 21:26:41 +00:00			`#define STAT_LED_RED_PIN 6`
			`#define STAT_LED_BLUE_PIN 11`
Overridable Options - Part 4 (PR#2556) Apply `ENABLED` / `DISABLED` / `HAS_SERVOS` macros to pins files. 2015-07-31 05:11:19 +00:00
Azteeg X3 overrides too 2015-02-20 01:28:38 +00:00			`#endif`
SPINDLE/LASER pins changes 2017-04-07 18:52:21 +00:00
			`//`
			`// Misc`
			`//`
Extended condition macros (#13419) Allow `ENABLED`, `DISABLED`, `PIN_EXISTS`, and `BUTTON_EXISTS` to take multiple arguments. Also add: - Alias `ANY(...)` for `!DISABLED(...)` - Alias `ANY_PIN(...)` for `PIN_EXISTS(a) \|\| PIN_EXISTS(b) ...` - Alias `EITHER(A,B)` for `ANY(...)` - Alias `ALL(...)` and `BOTH(A,B)` for `ENABLED(...)` - `NONE(...)` for `DISABLED(...)` 2019-03-17 04:43:06 +00:00			`#if ENABLED(CASE_LIGHT_ENABLE) && PIN_EXISTS(CASE_LIGHT, STAT_LED_RED) && STAT_LED_RED_PIN == CASE_LIGHT_PIN`
SPINDLE/LASER pins changes 2017-04-07 18:52:21 +00:00			`#undef STAT_LED_RED_PIN`
			`#endif`

			`//`
			`// M3/M4/M5 - Spindle/Laser Control`
			`//`
			`#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are no good with the AzteegX3 board`
SPINDLE_LASER_ENABLE => SPINDLE_LASER_ENA 2019-04-08 22:52:33 +00:00			`#undef SPINDLE_LASER_ENA_PIN`
SPINDLE/LASER pins changes 2017-04-07 18:52:21 +00:00			`#undef SPINDLE_DIR_PIN`

			`#if ENABLED(SPINDLE_LASER_ENABLE)`
			`#undef SDA // use EXP3 header`
			`#undef SCL`
			`#if SERVO0_PIN == 7`
			`#undef SERVO0_PIN`
Apply spacing in pins files 2018-03-28 17:51:59 +00:00			`#define SERVO0_PIN 11`
Fix case light logic on Azteeg_X3 boards. 2017-06-01 17:33:24 +00:00			`#endif`
Apply spacing in pins files 2018-03-28 17:51:59 +00:00			`#define SPINDLE_LASER_PWM_PIN 7 // MUST BE HARDWARE PWM`
SPINDLE_LASER_ENABLE => SPINDLE_LASER_ENA 2019-04-08 22:52:33 +00:00			`#define SPINDLE_LASER_ENA_PIN 20 // Pin should have a pullup!`
SPINDLE/LASER pins changes 2017-04-07 18:52:21 +00:00			`#define SPINDLE_DIR_PIN 21`
			`#endif`