MarlinFirmware/Marlin/src/pins/pins_RAMPS_SMART.h

/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */

/**
 * Arduino Due with RAMPS-SMART pin assignments
 *
 * Applies to the following boards:
 *
 *  RAMPS_SMART_EFB (Hotend, Fan, Bed)
 *  RAMPS_SMART_EEB (Hotend0, Hotend1, Bed)
 *  RAMPS_SMART_EFF (Hotend, Fan0, Fan1)
 *  RAMPS_SMART_EEF (Hotend0, Hotend1, Fan)
 *  RAMPS_SMART_SF  (Spindle, Controller Fan)
 *
 *  Differences between
 *  RAMPS_14 | RAMPS-SMART
 *      NONE | D16 (Additional AUX-3 pin(AUX3_2PIN), shares the same pin with AUX4_18PIN)
 *      NONE | D17 (Additional AUX-3 pin(AUX3_1PIN), shares the same pin with AUX4_17PIN)
 *        D0 | NONE
 *        D1 | NONE
 *    A3/D57 | NONE
 *    A4/D58 | NONE
 *    A5/D59 | A3/D57
 *    A9/D63 | A4/D58
 *   A10/D64 | A5/D59
 *   A11/D65 | D66
 *   A12/D66 | D67
 *       A13 | A9
 *       A14 | A10
 *       A15 | A11
 *
 *
 * REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER works fine connected to AUX-4 with
 * Smart Adapter, but requires removing the AUX3 pin header on the adapter to fit.
 * To use the SD card reader, wire its pins to AUX-3 (and use Software SPI).
 *
 * To use Hardware SPI for SD, the SDSS pin must be set to 52 instead of 53.
 * Hardware SPI also requires additional wiring because the board doesn't pass
 * the 6-pin SPI header from the DUE board.
 * (Search the web for "Arduino DUE Board Pinout" to see the correct header.)
 */

#ifndef __SAM3X8E__
  #error "Oops! Select 'Arduino Due' in 'Tools > Board.'"
#endif

#define BOARD_NAME "RAMPS-SMART"

#define IS_RAMPS_SMART
#include "pins_RAMPS.h"

// I2C EEPROM with 4K of space
#define I2C_EEPROM
#define E2END 0xFFF

#define RESET_PIN          42   // Resets the board if the jumper is attached

//
// Temperature Sensors
//
#undef TEMP_0_PIN
#define TEMP_0_PIN          9   // Analog Input

#undef TEMP_1_PIN
#define TEMP_1_PIN         10   // Analog Input

#undef TEMP_BED_PIN
#define TEMP_BED_PIN       11   // Analog Input

// SPI for Max6675 or Max31855 Thermocouple
#undef MAX6675_SS_PIN
#if DISABLED(SDSUPPORT)
  #define MAX6675_SS_PIN   67   // Do not use pin 53 if there is even the remote possibility of using Display/SD card
#else
  #define MAX6675_SS_PIN   67   // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
#endif

//
// LCD / Controller
//
// Support for AZSMZ 12864 LCD with SD Card 3D printer smart controller control panel
#if ENABLED(AZSMZ_12864)
  #define BEEPER_PIN       66   // Smart RAMPS 1.42 pinout diagram on RepRap WIKI erroneously says this should be pin 65
  #define DOGLCD_A0        59
  #define DOGLCD_CS        44
  #define BTN_EN1          58
  #define BTN_EN2          40
  #define BTN_ENC          67   // Smart RAMPS 1.42 pinout diagram on RepRap WIKI erroneously says this should be pin 66
  #define SD_DETECT_PIN    49   // Pin 49 for display sd interface, 72 for easy adapter board
  #define KILL_PIN         42
#endif