mirror of
https://github.com/MarlinFirmware/Marlin.git
synced 2024-11-22 18:25:18 +00:00
📌 Fix, extend Index Rev03 Mobo (#23851)
Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
This commit is contained in:
GatCode
Scott Lahteine
parent
c6f4b38877
commit
7dae720de5
@ -2183,9 +2183,9 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
|
||||
* Test Sensor & Heater pin combos.
|
||||
* Pins and Sensor IDs must be set for each heater
|
||||
*/
|
||||
#if !ANY_PIN(TEMP_0, TEMP_0_CS)
|
||||
#if HAS_EXTRUDERS && !ANY_PIN(TEMP_0, TEMP_0_CS)
|
||||
#error "TEMP_0_PIN or TEMP_0_CS_PIN not defined for this board."
|
||||
#elif !HAS_HEATER_0 && EXTRUDERS
|
||||
#elif HAS_EXTRUDERS && !HAS_HEATER_0
|
||||
#error "HEATER_0_PIN not defined for this board."
|
||||
#elif TEMP_SENSOR_0_IS_MAX_TC && !PIN_EXISTS(TEMP_0_CS)
|
||||
#error "TEMP_SENSOR_0 MAX thermocouple requires TEMP_0_CS_PIN."
|
||||
|
||||
@ -60,12 +60,12 @@
|
||||
|
||||
// None of these require limit switches by default, so we leave these commented
|
||||
// here for your reference.
|
||||
// #define I_MIN_PIN PA8
|
||||
// #define I_MAX_PIN PA8
|
||||
// #define J_MIN_PIN PD13
|
||||
// #define J_MAX_PIN PD13
|
||||
// #define K_MIN_PIN PC9
|
||||
// #define K_MAX_PIN PC9
|
||||
//#define I_MIN_PIN PA8
|
||||
//#define I_MAX_PIN PA8
|
||||
//#define J_MIN_PIN PD13
|
||||
//#define J_MAX_PIN PD13
|
||||
//#define K_MIN_PIN PC9
|
||||
//#define K_MAX_PIN PC9
|
||||
|
||||
//
|
||||
// Steppers
|
||||
@ -73,47 +73,81 @@
|
||||
#define X_STEP_PIN PB15
|
||||
#define X_DIR_PIN PB14
|
||||
#define X_ENABLE_PIN PD9
|
||||
#define X_SERIAL_TX_PIN PD8
|
||||
#define X_SERIAL_RX_PIN PD8
|
||||
|
||||
#define Y_STEP_PIN PE15
|
||||
#define Y_DIR_PIN PE14
|
||||
#define Y_ENABLE_PIN PB13
|
||||
#define Y_SERIAL_TX_PIN PB12
|
||||
#define Y_SERIAL_RX_PIN PB12
|
||||
|
||||
#define Z_STEP_PIN PE7
|
||||
#define Z_DIR_PIN PB1
|
||||
#define Z_ENABLE_PIN PE9
|
||||
#define Z_SERIAL_TX_PIN PE8
|
||||
#define Z_SERIAL_RX_PIN PE8
|
||||
|
||||
#define I_STEP_PIN PC4
|
||||
#define I_DIR_PIN PA4
|
||||
#define I_ENABLE_PIN PB0
|
||||
#define I_SERIAL_TX_PIN PC5
|
||||
#define I_SERIAL_RX_PIN PC5
|
||||
|
||||
#define J_STEP_PIN PE11
|
||||
#define J_DIR_PIN PE10
|
||||
#define J_ENABLE_PIN PE13
|
||||
#define J_SERIAL_TX_PIN PE12
|
||||
#define J_SERIAL_RX_PIN PE12
|
||||
#define K_SERIAL_TX_PIN PA2
|
||||
#define K_SERIAL_RX_PIN PA2
|
||||
|
||||
#define K_STEP_PIN PD6
|
||||
#define K_DIR_PIN PD7
|
||||
#define K_ENABLE_PIN PA3
|
||||
|
||||
// Reduce baud rate to improve software serial reliability
|
||||
#define TMC_BAUD_RATE 19200
|
||||
#if HAS_TMC_SPI
|
||||
/**
|
||||
* Make sure to configure the jumpers on the back side of the Mobo according to
|
||||
* this diagram: https://github.com/MarlinFirmware/Marlin/pull/23851
|
||||
*/
|
||||
#error "SPI drivers require a custom jumper configuration, see comment above! Comment out this line to continue."
|
||||
|
||||
// Not required for this board. Fails to compile otherwise.
|
||||
// PD0 is not connected on this board.
|
||||
#define TEMP_0_PIN PD0
|
||||
#if AXIS_HAS_SPI(X)
|
||||
#define X_CS_PIN PD8
|
||||
#endif
|
||||
#if AXIS_HAS_SPI(Y)
|
||||
#define Y_CS_PIN PB12
|
||||
#endif
|
||||
#if AXIS_HAS_SPI(Z)
|
||||
#define Z_CS_PIN PE8
|
||||
#endif
|
||||
#if AXIS_HAS_SPI(I)
|
||||
#define I_CS_PIN PC5
|
||||
#endif
|
||||
#if AXIS_HAS_SPI(J)
|
||||
#define J_CS_PIN PE12
|
||||
#endif
|
||||
#if AXIS_HAS_SPI(K)
|
||||
#define K_CS_PIN PA2
|
||||
#endif
|
||||
|
||||
// General use mosfets, useful for things like pumps and solenoids
|
||||
#elif HAS_TMC_UART
|
||||
|
||||
#define X_SERIAL_TX_PIN PD8
|
||||
#define X_SERIAL_RX_PIN X_SERIAL_TX_PIN
|
||||
|
||||
#define Y_SERIAL_TX_PIN PB12
|
||||
#define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN
|
||||
|
||||
#define Z_SERIAL_TX_PIN PE8
|
||||
#define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN
|
||||
|
||||
#define I_SERIAL_TX_PIN PC5
|
||||
#define I_SERIAL_RX_PIN I_SERIAL_TX_PIN
|
||||
|
||||
#define J_SERIAL_TX_PIN PE12
|
||||
#define J_SERIAL_RX_PIN J_SERIAL_TX_PIN
|
||||
|
||||
#define K_SERIAL_TX_PIN PA2
|
||||
#define K_SERIAL_RX_PIN K_SERIAL_TX_PIN
|
||||
|
||||
// Reduce baud rate to improve software serial reliability
|
||||
#define TMC_BAUD_RATE 19200
|
||||
|
||||
#endif
|
||||
|
||||
//
|
||||
// Heaters / Fans
|
||||
//
|
||||
#define FAN_PIN PE2
|
||||
#define FAN1_PIN PE3
|
||||
#define FAN2_PIN PE4
|
||||
@ -121,16 +155,26 @@
|
||||
|
||||
#define FAN_SOFT_PWM_REQUIRED
|
||||
|
||||
// Neopixel Rings
|
||||
//
|
||||
// Neopixel
|
||||
//
|
||||
#define NEOPIXEL_PIN PC7
|
||||
#define NEOPIXEL2_PIN PC8
|
||||
|
||||
//
|
||||
// SPI
|
||||
//
|
||||
#define MISO_PIN PB4
|
||||
#define MOSI_PIN PB5
|
||||
#define SCK_PIN PB3
|
||||
|
||||
#define TMC_SW_MISO MISO_PIN
|
||||
#define TMC_SW_MOSI MOSI_PIN
|
||||
#define TMC_SW_SCK SCK_PIN
|
||||
|
||||
//
|
||||
// I2C
|
||||
//
|
||||
#define I2C_SDA_PIN PB7
|
||||
#define I2C_SCL_PIN PB6
|
||||
|
||||
|
||||
Loading…
Reference in New Issue
Block a user