2016-07-22 13:28:01 +00:00
# ifndef CONFIGURATION_ADV_H
# define CONFIGURATION_ADV_H
//===========================================================================
//=============================Thermal Settings ============================
//===========================================================================
# ifdef BED_LIMIT_SWITCHING
# define BED_HYSTERESIS 2 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
# endif
# define BED_CHECK_INTERVAL 5000 //ms between checks in bang-bang control
# ifdef PIDTEMP
// this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated.
2021-05-30 12:24:47 +00:00
// #define PID_ADD_EXTRUSION_RATE
2016-07-22 13:28:01 +00:00
# ifdef PID_ADD_EXTRUSION_RATE
# define DEFAULT_Kc (1) //heating power=Kc*(e_speed)
# endif
# endif
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
//The maximum buffered steps/sec of the extruder motor are called "se".
//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
// you exit the value by any M109 without F*
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
// on an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
//#define AUTOTEMP
# ifdef AUTOTEMP
# define AUTOTEMP_OLDWEIGHT 0.98
# endif
//Show Temperature ADC value
//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
//#define SHOW_TEMP_ADC_VALUES
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
//#define EXTRUDER_RUNOUT_PREVENT
# define EXTRUDER_RUNOUT_MINTEMP 190
# define EXTRUDER_RUNOUT_SECONDS 30.
# define EXTRUDER_RUNOUT_ESTEPS 14. //mm filament
# define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed
# define EXTRUDER_RUNOUT_EXTRUDE 100
//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
# define TEMP_SENSOR_AD595_OFFSET 0.0
# define TEMP_SENSOR_AD595_GAIN 1.0
//This is for controlling a fan to cool down the stepper drivers
//it will turn on when any driver is enabled
//and turn off after the set amount of seconds from last driver being disabled again
# define CONTROLLERFAN_PIN -1 //Pin used for the fan to cool controller (-1 to disable)
# define CONTROLLERFAN_SECS 60 //How many seconds, after all motors were disabled, the fan should run
# define CONTROLLERFAN_SPEED 255 // == full speed
// When first starting the main fan, run it at full speed for the
// given number of milliseconds. This gets the fan spinning reliably
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
2017-09-21 13:20:02 +00:00
# define FAN_KICKSTART_TIME 800
2016-07-22 13:28:01 +00:00
2020-07-23 14:28:25 +00:00
/**
2021-01-19 08:01:46 +00:00
* Auto - report all at once with M155 S < seconds > C [ bitmask ] with single timer
*
* bit 0 = Auto - report temperatures
* bit 1 = Auto - report fans
* bit 2 = Auto - report position
* bit 3 = free
* bit 4 = free
* bit 5 = free
* bit 6 = free
* bit 7 = free
*/
2021-01-22 11:26:29 +00:00
# define AUTO_REPORT
2016-07-22 13:28:01 +00:00
//===========================================================================
//=============================Mechanical Settings===========================
//===========================================================================
# define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
//// AUTOSET LOCATIONS OF LIMIT SWITCHES
//// Added by ZetaPhoenix 09-15-2012
# ifdef MANUAL_HOME_POSITIONS // Use manual limit switch locations
# define X_HOME_POS MANUAL_X_HOME_POS
# define Y_HOME_POS MANUAL_Y_HOME_POS
# define Z_HOME_POS MANUAL_Z_HOME_POS
# else //Set min/max homing switch positions based upon homing direction and min/max travel limits
//X axis
# if X_HOME_DIR == -1
# ifdef BED_CENTER_AT_0_0
# define X_HOME_POS X_MAX_LENGTH * -0.5
# else
# define X_HOME_POS X_MIN_POS
# endif //BED_CENTER_AT_0_0
# else
# ifdef BED_CENTER_AT_0_0
# define X_HOME_POS X_MAX_LENGTH * 0.5
# else
# define X_HOME_POS X_MAX_POS
# endif //BED_CENTER_AT_0_0
# endif //X_HOME_DIR == -1
//Y axis
# if Y_HOME_DIR == -1
# ifdef BED_CENTER_AT_0_0
# define Y_HOME_POS Y_MAX_LENGTH * -0.5
# else
# define Y_HOME_POS Y_MIN_POS
# endif //BED_CENTER_AT_0_0
# else
# ifdef BED_CENTER_AT_0_0
# define Y_HOME_POS Y_MAX_LENGTH * 0.5
# else
# define Y_HOME_POS Y_MAX_POS
# endif //BED_CENTER_AT_0_0
# endif //Y_HOME_DIR == -1
// Z axis
# if Z_HOME_DIR == -1 //BED_CENTER_AT_0_0 not used
# define Z_HOME_POS Z_MIN_POS
# else
# define Z_HOME_POS Z_MAX_POS
# endif //Z_HOME_DIR == -1
# endif //End auto min/max positions
//END AUTOSET LOCATIONS OF LIMIT SWITCHES -ZP
// A single Z stepper driver is usually used to drive 2 stepper motors.
// Uncomment this define to utilize a separate stepper driver for each Z axis motor.
// Only a few motherboards support this, like RAMPS, which have dual extruder support (the 2nd, often unused, extruder driver is used
// to control the 2nd Z axis stepper motor). The pins are currently only defined for a RAMPS motherboards.
// On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
//#define Z_DUAL_STEPPER_DRIVERS
# ifdef Z_DUAL_STEPPER_DRIVERS
# undef EXTRUDERS
# define EXTRUDERS 1
# endif
// Same again but for Y Axis.
//#define Y_DUAL_STEPPER_DRIVERS
// Define if the two Y drives need to rotate in opposite directions
2018-06-10 14:04:32 +00:00
# define INVERT_Y2_VS_Y_DIR 1
2016-07-22 13:28:01 +00:00
# ifdef Y_DUAL_STEPPER_DRIVERS
# undef EXTRUDERS
# define EXTRUDERS 1
# endif
# if defined (Z_DUAL_STEPPER_DRIVERS) && defined (Y_DUAL_STEPPER_DRIVERS)
# error "You cannot have dual drivers for both Y and Z"
# endif
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
# define X_HOME_RETRACT_MM 5
# define Y_HOME_RETRACT_MM 5
# define Z_HOME_RETRACT_MM 2
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
# define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step). Toshiba steppers are 4x slower, but Prusa3D does not use those.
//By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
2018-06-10 14:04:32 +00:00
# define INVERT_X_STEP_PIN 0
# define INVERT_Y_STEP_PIN 0
# define INVERT_Z_STEP_PIN 0
# define INVERT_E_STEP_PIN 0
2016-07-22 13:28:01 +00:00
//default stepper release if idle
# define DEFAULT_STEPPER_DEACTIVE_TIME 60
# define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
# define DEFAULT_MINTRAVELFEEDRATE 0.0
// Feedrates for manual moves along X, Y, Z, E from panel
//Comment to disable setting feedrate multiplier via encoder
2018-07-16 00:13:52 +00:00
# define ULTIPANEL_FEEDMULTIPLY
2016-07-22 13:28:01 +00:00
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
# define DEFAULT_MINSEGMENTTIME 20000
// If defined the movements slow down when the look ahead buffer is only half full
# define SLOWDOWN
// MS1 MS2 Stepper Driver Microstepping mode table
# define MICROSTEP1 LOW,LOW
# define MICROSTEP2 HIGH,LOW
# define MICROSTEP4 LOW,HIGH
# define MICROSTEP8 HIGH,HIGH
# define MICROSTEP16 HIGH,HIGH
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
# define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
//===========================================================================
//=============================Additional Features===========================
//===========================================================================
//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
# define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
2018-06-10 14:04:32 +00:00
# define SD_FINISHED_STEPPERRELEASE 1 //if sd support and the file is finished: disable steppers?
2016-07-22 13:28:01 +00:00
# define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
# define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
// if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
// using:
//#define MENU_ADDAUTOSTART
2017-12-06 16:48:16 +00:00
/**
* Sort SD file listings in alphabetical order .
*
* With this option enabled , items on SD cards will be sorted
* by name for easier navigation .
*
* By default . . .
*
* - Use the slowest - but safest - method for sorting .
* - Folders are sorted to the top .
* - The sort key is statically allocated .
* - No added G - code ( M34 ) support .
* - 40 item sorting limit . ( Items after the first 40 are unsorted . )
*
* SD sorting uses static allocation ( as set by SDSORT_LIMIT ) , allowing the
* compiler to calculate the worst - case usage and throw an error if the SRAM
* limit is exceeded .
*/
# define SDCARD_SORT_ALPHA //Alphabetical sorting of SD files menu
// SD Card Sorting options
# ifdef SDCARD_SORT_ALPHA
# define SD_SORT_TIME 0
# define SD_SORT_ALPHA 1
# define SD_SORT_NONE 2
2021-02-26 07:18:59 +00:00
// #define SHELLSORT
2019-11-27 09:03:34 +00:00
// #define SORTING_DUMP
2017-12-06 16:48:16 +00:00
2017-12-11 10:30:49 +00:00
# define SDSORT_LIMIT 100 // Maximum number of sorted items (10-256).
# define FOLDER_SORTING -1 // -1=above 0=none 1=below
2017-12-06 16:48:16 +00:00
# endif
# if defined(SDCARD_SORT_ALPHA)
2021-02-03 17:18:13 +00:00
# define HAS_FOLDER_SORTING (FOLDER_SORTING)
2017-12-06 16:48:16 +00:00
# endif
2022-02-10 15:42:02 +00:00
// Enabe this option to get a pretty message whenever the endstop gets hit (as in the position at which the endstop got triggered)
//#define VERBOSE_CHECK_HIT_ENDSTOPS
2016-07-22 13:28:01 +00:00
// Enable the option to stop SD printing when hitting and endstops, needs to be enabled from the LCD menu when this option is enabled.
//#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
// Babystepping enables the user to control the axis in tiny amounts, independently from the normal printing process
// it can e.g. be used to change z-positions in the print startup phase in real-time
// does not respect endstops!
# define BABYSTEPPING
# ifdef BABYSTEPPING
# define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
2018-06-10 14:04:32 +00:00
# define BABYSTEP_INVERT_Z 0 //1 for inverse movements in Z
2016-07-22 13:28:01 +00:00
# define BABYSTEP_Z_MULTIPLICATOR 2 //faster z movements
# ifdef COREXY
# error BABYSTEPPING not implemented for COREXY yet.
# endif
# endif
2017-07-06 23:58:02 +00:00
/**
2019-03-17 18:49:21 +00:00
* Linear Pressure Control v1 .5
*
* Assumption : advance [ steps ] = k * ( delta velocity [ steps / s ] )
* K = 0 means advance disabled .
*
2019-05-26 15:14:06 +00:00
* NOTE : K values for LIN_ADVANCE 1.5 differs from earlier versions !
2019-03-17 18:49:21 +00:00
*
* Set K around 0.22 for 3 mm PLA Direct Drive with ~ 6.5 cm between the drive gear and heatbreak .
* Larger K values will be needed for flexible filament and greater distances .
* If this algorithm produces a higher speed offset than the extruder can handle ( compared to E jerk )
* print acceleration will be reduced during the affected moves to keep within the limit .
*
* See http : //marlinfw.org/docs/features/lin_advance.html for full instructions.
* Mention @ Sebastianv650 on GitHub to alert the author of any issues .
*/
2018-02-02 21:56:13 +00:00
# define LIN_ADVANCE
2017-07-06 23:58:02 +00:00
# ifdef LIN_ADVANCE
2020-04-28 15:24:03 +00:00
# define LA_K_DEF 0 // Default K factor (Unit: mm compression per 1mm/s extruder speed)
# define LA_K_MAX 10 // Maximum acceptable K factor (exclusive, see notes in planner.cpp:plan_buffer_line)
# define LA_LA10_MIN LA_K_MAX // Lin. Advance 1.0 threshold value (inclusive)
2020-07-20 10:42:28 +00:00
//#define LA_FLOWADJ // Adjust LA along with flow/M221 for uniform width
2020-04-28 15:24:03 +00:00
//#define LA_NOCOMPAT // Disable Linear Advance 1.0 compatibility
//#define LA_LIVE_K // Allow adjusting K in the Tune menu
//#define LA_DEBUG // If enabled, this will generate debug information output over USB.
//#define LA_DEBUG_LOGIC // @wavexx: setup logic channels for isr debugging
2017-07-06 23:58:02 +00:00
# endif
2016-07-22 13:28:01 +00:00
// Arc interpretation settings:
# define MM_PER_ARC_SEGMENT 1
# define N_ARC_CORRECTION 25
const unsigned int dropsegments = 5 ; //everything with less than this number of steps will be ignored as move and joined with the next movement
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
// be commented out otherwise
# define SDCARDDETECTINVERTED
2018-07-16 00:13:52 +00:00
# undef SDCARDDETECTINVERTED
2016-07-22 13:28:01 +00:00
// Power Signal Control Definitions
// By default use ATX definition
# ifndef POWER_SUPPLY
# define POWER_SUPPLY 1
# endif
// 1 = ATX
# if (POWER_SUPPLY == 1)
# define PS_ON_AWAKE LOW
# define PS_ON_ASLEEP HIGH
# endif
// 2 = X-Box 360 203W
# if (POWER_SUPPLY == 2)
# define PS_ON_AWAKE HIGH
# define PS_ON_ASLEEP LOW
# endif
// Control heater 0 and heater 1 in parallel.
//#define HEATERS_PARALLEL
2021-02-10 15:18:47 +00:00
//LCD status clock interval timer to switch between
// remaining print time
// and time to change/pause/interaction
2021-02-12 10:29:47 +00:00
# define CLOCK_INTERVAL_TIME 5
2021-02-10 15:18:47 +00:00
2016-07-22 13:28:01 +00:00
//===========================================================================
//=============================Buffers ============================
//===========================================================================
// The number of linear motions that can be in the plan at any give time.
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
# if defined SDSUPPORT
# define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
# else
# define BLOCK_BUFFER_SIZE 16 // maximize block buffer
# endif
//The ASCII buffer for receiving from the serial:
# define MAX_CMD_SIZE 96
# define BUFSIZE 4
2017-09-21 15:50:39 +00:00
// The command header contains the following values:
// 1st byte: the command source (CMDBUFFER_CURRENT_TYPE_USB, CMDBUFFER_CURRENT_TYPE_SDCARD, CMDBUFFER_CURRENT_TYPE_UI or CMDBUFFER_CURRENT_TYPE_CHAINED)
// 2nd and 3rd byte (LSB first) contains a 16bit length of a command including its preceding comments.
# define CMDHDRSIZE 3
2016-07-22 13:28:01 +00:00
// Firmware based and LCD controlled retract
// M207 and M208 can be used to define parameters for the retraction.
// The retraction can be called by the slicer using G10 and G11
// until then, intended retractions can be detected by moves that only extrude and the direction.
// the moves are than replaced by the firmware controlled ones.
# define FWRETRACT //ONLY PARTIALLY TESTED
# ifdef FWRETRACT
# define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
# define RETRACT_LENGTH 3 //default retract length (positive mm)
# define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change
# define RETRACT_FEEDRATE 45 //default feedrate for retracting (mm/s)
# define RETRACT_ZLIFT 0 //default retract Z-lift
# define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering)
# define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change)
# define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
# endif
//adds support for experimental filament exchange support M600; requires display
# ifdef FILAMENTCHANGEENABLE
# ifdef EXTRUDER_RUNOUT_PREVENT
# error EXTRUDER_RUNOUT_PREVENT currently incompatible with FILAMENTCHANGE
# endif
# endif
2020-09-11 13:11:28 +00:00
/**
* Include capabilities in M115 output
*/
2020-09-11 15:48:44 +00:00
# define EXTENDED_CAPABILITIES_REPORT
2020-09-11 13:11:28 +00:00
2021-03-11 14:00:49 +00:00
/**
* Enable M120 / M121 G - code commands
*
*/
//#define M120_M121_ENABLED //Be careful enabling and using these G-code commands.
2016-07-22 13:28:01 +00:00
//===========================================================================
//============================= Define Defines ============================
//===========================================================================
# if EXTRUDERS > 1 && defined HEATERS_PARALLEL
# error "You cannot use HEATERS_PARALLEL if EXTRUDERS > 1"
# endif
# if TEMP_SENSOR_0 > 0
# define THERMISTORHEATER_0 TEMP_SENSOR_0
# define HEATER_0_USES_THERMISTOR
# endif
# if TEMP_SENSOR_1 > 0
# define THERMISTORHEATER_1 TEMP_SENSOR_1
# define HEATER_1_USES_THERMISTOR
# endif
# if TEMP_SENSOR_2 > 0
# define THERMISTORHEATER_2 TEMP_SENSOR_2
# define HEATER_2_USES_THERMISTOR
# endif
# if TEMP_SENSOR_BED > 0
# define THERMISTORBED TEMP_SENSOR_BED
# define BED_USES_THERMISTOR
# endif
2017-09-06 14:04:50 +00:00
# if TEMP_SENSOR_PINDA > 0
# define THERMISTORPINDA TEMP_SENSOR_PINDA
# endif
# if TEMP_SENSOR_AMBIENT > 0
# define THERMISTORAMBIENT TEMP_SENSOR_AMBIENT
# endif
2016-07-22 13:28:01 +00:00
# if TEMP_SENSOR_0 == -1
# define HEATER_0_USES_AD595
# endif
# if TEMP_SENSOR_1 == -1
# define HEATER_1_USES_AD595
# endif
# if TEMP_SENSOR_2 == -1
# define HEATER_2_USES_AD595
# endif
# if TEMP_SENSOR_BED == -1
# define BED_USES_AD595
# endif
# if TEMP_SENSOR_0 == -2
# define HEATER_0_USES_MAX6675
# endif
# if TEMP_SENSOR_0 == 0
# undef HEATER_0_MINTEMP
# undef HEATER_0_MAXTEMP
# endif
# if TEMP_SENSOR_1 == 0
# undef HEATER_1_MINTEMP
# undef HEATER_1_MAXTEMP
# endif
# if TEMP_SENSOR_2 == 0
# undef HEATER_2_MINTEMP
# undef HEATER_2_MAXTEMP
# endif
# if TEMP_SENSOR_BED == 0
# undef BED_MINTEMP
# undef BED_MAXTEMP
# endif
2020-06-08 01:14:49 +00:00
# if TEMP_SENSOR_AMBIENT == 0
# undef AMBIENT_MINTEMP
# undef AMBIENT_MAXTEMP
# endif
2016-07-22 13:28:01 +00:00
# endif //__CONFIGURATION_ADV_H
