config bundles, project files (3MFs, AMFs). When loading these files,
the caller may decide whether to substitute some of the configuration
values the current PrusaSlicer version does not understand with
some reasonable default value, and whether to report it. If substitution
is disabled, an exception is being thrown as before this commit.
If substitution is enabled, list of substitutions is returned by the
API to be presented to the user. This allows us to introduce for example
new firmware flavor key in PrusaSlicer 2.4 while letting PrusaSlicer
2.3.2 to fall back to some default and to report it to the user.
As a preparation for PrusaSlicer 2.4.0, the new firmware_flavor
"marlinfirmware" (signifying Marlin 2.0 and newer) that is not
supported by 2.3.2 yet will default to "marlin" (signifying legacy
Marlin).
When slicing from command line, substutions are performed by default
and reported into the console, however substitutions may be either
disabled or made silent with the new "config-compatibility" command
line option.
Substitute enums and bools only. Allow booleans to be parsed as
true: "1", "enabled", "on" case insensitive
false: "0", "disabled", "off" case insensitive
This will allow us in the future for example to switch the draft_shield
boolean to an enum with the following values: "disabled" / "enabled" / "limited".
Added "enum_bitmask.hpp" - support for type safe sets of options.
See for example PresetBundle::load_configbundle(...
LoadConfigBundleAttributes flags) for an example of intended usage.
WIP: GUI for reporting the list of config substitutions needs to be
implemented by @YuSanka.
Cherry-pick of 2e55898d78
Fix of an extremely slow bridging calculation, caused by an extremely
slow bridged area detection function, of which the results were never used.
Fixes "slicing fails or takes too long #5974"
This is a fix of a bug, which was in Slic3r forever, where raw slices
were not cached, but recalculated from classified regions, where
merging the regions did not produce the original contour reliably.
Fixes [2.3.0-beta2] Odd bad slicing related to infill (?) percentage #5407
(non-spiral vase layers) were being closed.
Fixes Bad slicing in vase mode (unexpected bridge and solid infill layers) #3326
Fixes Model with holes in the base does not slice properly in "Vase Mode" #5359
1) New algorithm for connecting along the perimeters is now applied
to Honeycomb, Hilbert and similar planar filling curves.
2) The old expensive path chaining is not applied if the new algorithm
to connect along the perimeter lines is called afterwards.
Refactored Arrange interface: remove the union based BedShapeHint, replace it with proper function overloads
WARN: this commit is only intermediate, it does not compile.
collisions against already printed objects: Rotation of an object
was not being taken into account.
Fixes#2450 PrusaSlicer 2.0 Sequential printing vs rotate object
Fixes#3585 Always Sequential Printing Error (Regardless of setting, placement or object size)
Fixed some collisions in sequential print just after arrangement by
making the validation using a slightly lower extruder radius value
than the arrangement.
Refactored PrintObject coordinate system so that the PrintObject's
coordinate system is always centered in respect to its ModelObject's
geometries. This refactoring may improve path planning a bit and
it may lower the requirements on bits representing Clipper coordinates
by 1 bit.
DynamicPrintConfig::full_print_config()
new cheaper constructors of DynamicConfig / DynamicPrintConfig from ConfigBase
Unit tests: ported test_model from upstream Slic3r, thanks @lordofhyphens
Unit tests refactored to use less autos and initializer lists for readibility,
DynamicPrintConfig is handled by value, not by shared pointer.
Layer newly remembers bounding boxes of slices,
the bounding boxes are used by G-code generator & newly the support
generator.
Slices are stored as ExPolygons, not ExPolygonCollection.
