2024.07.20 18:19

filament/Fiberlogy FiberFlex 40D @all.ini

@@ -0,0 +1,75 @@
+# generated by PrusaSlicer 2.7.4+linux-x64-GTK3 on 2024-07-20 at 15:51:12 UTC
+bed_temperature = 60
+bridge_fan_speed = 75
+compatible_printers = 
+compatible_printers_condition = 
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 5
+enable_dynamic_fan_speeds = 0
+end_filament_gcode = "; Filament-specific end gcode"
+extrusion_multiplier = 1.1
+fan_always_on = 1
+fan_below_layer_time = 100
+filament_colour = #008000
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 39.41
+filament_density = 1.16
+filament_deretract_speed = 20
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 4
+filament_minimal_purge_on_wipe_tower = 15
+filament_multitool_ramming = 0
+filament_multitool_ramming_flow = 10
+filament_multitool_ramming_volume = 10
+filament_notes = ""
+filament_purge_multiplier = 100%
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = 2
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = 2.2
+filament_retract_length_toolchange = nil
+filament_retract_lift = 0
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_restart_extra_toolchange = nil
+filament_retract_speed = 60
+filament_settings_id = ""
+filament_soluble = 0
+filament_spool_weight = 330
+filament_stamping_distance = 0
+filament_stamping_loading_speed = 20
+filament_toolchange_delay = 0
+filament_travel_lift_before_obstacle = nil
+filament_travel_max_lift = 0.6
+filament_travel_ramping_lift = nil
+filament_travel_slope = nil
+filament_type = FLEX
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = Fiberlogy
+filament_wipe = 0
+first_layer_bed_temperature = 60
+first_layer_temperature = 220
+full_fan_speed_layer = 5
+idle_temperature = 70
+inherits = Fiberlogy FiberFlex 40D @MK4
+max_fan_speed = 75
+min_fan_speed = 25
+min_print_speed = 15
+overhang_fan_speed_0 = 0
+overhang_fan_speed_1 = 0
+overhang_fan_speed_2 = 0
+overhang_fan_speed_3 = 0
+slowdown_below_layer_time = 15
+start_filament_gcode = "M900 K0 ; Filament gcode\n\nM142 S36 ; set heatbreak target temp"
+temperature = 220

printer/Original Prusa MK4 0.4 nozzle - text over things.ini

@@ -0,0 +1,86 @@
+# generated by PrusaSlicer 2.7.4+linux-x64-GTK3 on 2024-07-20 at 13:54:43 UTC
+autoemit_temperature_commands = 1
+bed_custom_model = 
+bed_custom_texture = 
+bed_shape = 0x0,250x0,250x210,0x210
+before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n
+between_objects_gcode = 
+binary_gcode = 1
+color_change_gcode = M600\nG1 E0.3 F1500 ; prime after color change
+cooling_tube_length = 5
+cooling_tube_retraction = 91.5
+default_filament_profile = "Prusament PLA @PG"
+default_print_profile = 0.20mm QUALITY @MK4 0.4
+deretract_speed = 25
+end_gcode = M17 ; enable steppers\\nM862.3 P "[printer_model]" ; printer model check\\nM862.1 P[nozzle_diameter] ; nozzle diameter check\\nM555 X{(min(print_bed_max[0], first_layer_print_min[0] + 32) - 32)} Y{(max(0, first_layer_print_min[1]) - 4)} W{((min(print_bed_max[0], max(first_layer_print_min[0] + 32, first_layer_print_max[0])))) - ((min(print_bed_max[0], first_layer_print_min[0] + 32) - 32))} H{((first_layer_print_max[1])) - ((max(0, first_layer_print_min[1]) - 4))}\\n\\nG90 ; use absolute coordinates\\nM83 ; extruder relative mode\\n\\nM140 S[first_layer_bed_temperature] ; set bed temp\\n{if filament_type[initial_tool]=="PC" or filament_type[initial_tool]=="NYLON"}\\nM104 S{first_layer_temperature[initial_tool]-25} ; set extruder temp for bed leveling\\nM109 R{first_layer_temperature[initial_tool]-25} ; wait for temp\\n{elsif filament_type[initial_tool]=="FLEX"}\\nM104 S210 ; set extruder temp for bed leveling\\nM109 R210 ; wait for temp\\n{else}\\nM104 S170 ; set extruder temp for bed leveling\\nM109 R170 ; wait for temp\\n{endif}\\n\\nM84 E ; turn off E motor\\n\\nG28 ; home all without mesh bed level\\n\\n; probe to clean the nozzle\\nG1 X{(min(print_bed_max[0], first_layer_print_min[0] + 32) - 32)+32} Y{((first_layer_print_min[1]) - 4)} Z{5} F4800\\n\\nM302 S160 ; lower cold extrusion limit to 160C\\n\\n{if filament_type[initial_tool]=="FLEX"}\\nG1 E-4 F2400 ; retraction\\n{else}\\nG1 E-2 F2400 ; retraction\\n{endif}\\n\\nM84 E ; turn off E motor\\n\\nG29 P9 X{(min(print_bed_max[0], first_layer_print_min[0] + 32) - 32)} Y{(max(0, first_layer_print_min[1]) - 4)} W{32} H{4}\\n\\n{if first_layer_bed_temperature[initial_tool]<=60}M106 S100{endif}\\n\\nG0 X{(min(print_bed_max[0], first_layer_print_min[0] + 32) - 32)} Y{(max(0, first_layer_print_min[1]) - 4)} Z{40} F10000\\n\\nM190 S[first_layer_bed_temperature] ; wait for bed temp\\n\\nM107\\n\\n;\\n; MBL\\n;\\nM84 E ; turn off E motor\\nG29 ; mesh bed leveling\\nM104 S[first_layer_temperature] ; set extruder temp\\nG0 X{(min(print_bed_max[0], first_layer_print_min[0] + 32) - 32)} Y{(max(0, first_layer_print_min[1]) - 4) + 4 - 4.5} Z{30} F4800\\n\\nM109 S[first_layer_temperature] ; wait for extruder temp\\nG1 Z0.2 F720\\nG92 E0\\n\\nM569 S0 E ; set spreadcycle mode for extruder\\n\\n;\\n; Extrude purge line\\n;\\n{if filament_type[initial_tool]=="FLEX"}\\nG1 E4 F2400 ; deretraction\\n{else}\\nG1 E2 F2400 ; deretraction\\n{endif}\\n\\n; move right\\nG1 X{(min(print_bed_max[0], first_layer_print_min[0] + 32) - 32) + 32} E{32 * 0.15} F1000\\n; move down\\nG1 Y{(max(0, first_layer_print_min[1]) - 4) + 4 - 4.5 - 1.5} E{1.5 * 0.15} F1000\\n; move left\\nG1 X{(min(print_bed_max[0], first_layer_print_min[0] + 32) - 32)} E{32 * 0.30} F800\\n\\nG92 E0\\nM221 S100 ; set flow to 100%
+extra_loading_move = -2
+extruder_colour = ""
+extruder_offset = 0x0
+gcode_flavor = marlin2
+high_current_on_filament_swap = 0
+host_type = prusalink
+inherits = Original Prusa MK4 0.4 nozzle
+layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
+machine_limits_usage = emit_to_gcode
+machine_max_acceleration_e = 2500,2500
+machine_max_acceleration_extruding = 2000,2000
+machine_max_acceleration_retracting = 1200,1200
+machine_max_acceleration_travel = 2000,2000
+machine_max_acceleration_x = 2500,2500
+machine_max_acceleration_y = 2500,2500
+machine_max_acceleration_z = 200,200
+machine_max_feedrate_e = 100,100
+machine_max_feedrate_x = 200,160
+machine_max_feedrate_y = 200,160
+machine_max_feedrate_z = 40,40
+machine_max_jerk_e = 10,10
+machine_max_jerk_x = 8,8
+machine_max_jerk_y = 8,8
+machine_max_jerk_z = 2,2
+machine_min_extruding_rate = 0
+machine_min_travel_rate = 0
+max_layer_height = 0.3
+max_print_height = 220
+min_layer_height = 0.07
+multimaterial_purging = 140
+nozzle_diameter = 0.4
+parking_pos_retraction = 92
+pause_print_gcode = M601
+print_host = 
+printer_model = MK4
+printer_notes = Do not remove the keywords below.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK4\nPG
+printer_settings_id = 
+printer_technology = FFF
+printer_variant = 0.4
+printer_vendor = 
+printhost_apikey = 
+printhost_cafile = 
+remaining_times = 1
+retract_before_travel = 1.5
+retract_before_wipe = 80%
+retract_layer_change = 1
+retract_length = 0.8
+retract_length_toolchange = 0
+retract_lift = 0.2
+retract_lift_above = 0
+retract_lift_below = 219
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 35
+silent_mode = 1
+single_extruder_multi_material = 0
+start_gcode = M17 ; enable steppers\nM862.3 P "[printer_model]" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM555 X{(min(print_bed_max[0], first_layer_print_min[0] + 32) - 32)} Y{(max(0, first_layer_print_min[1]) - 4)} W{((min(print_bed_max[0], max(first_layer_print_min[0] + 32, first_layer_print_max[0])))) - ((min(print_bed_max[0], first_layer_print_min[0] + 32) - 32))} H{((first_layer_print_max[1])) - ((max(0, first_layer_print_min[1]) - 4))}\n\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\n\nM140 S[first_layer_bed_temperature] ; set bed temp\n{if filament_type[initial_tool]=="PC" or filament_type[initial_tool]=="NYLON"}\nM104 S{first_layer_temperature[initial_tool]-25} ; set extruder temp for bed leveling\nM109 R{first_layer_temperature[initial_tool]-25} ; wait for temp\n{elsif filament_type[initial_tool]=="FLEX"}\nM104 S210 ; set extruder temp for bed leveling\nM109 R210 ; wait for temp\n{else}\nM104 S170 ; set extruder temp for bed leveling\nM109 R170 ; wait for temp\n{endif}\n\nM84 E ; turn off E motor\n\nG28 ; home all without mesh bed level\n\n; probe to clean the nozzle\nG1 X{(min(print_bed_max[0], first_layer_print_min[0] + 32) - 32)+32} Y{((first_layer_print_min[1]) - 4)} Z{5} F4800\n\nM302 S160 ; lower cold extrusion limit to 160C\n\n{if filament_type[initial_tool]=="FLEX"}\nG1 E-4 F2400 ; retraction\n{else}\nG1 E-2 F2400 ; retraction\n{endif}\n\nM84 E ; turn off E motor\n\nG29 P9 X{(min(print_bed_max[0], first_layer_print_min[0] + 32) - 32)} Y{(max(0, first_layer_print_min[1]) - 4)} W{32} H{4}\n\n{if first_layer_bed_temperature[initial_tool]<=60}M106 S100{endif}\n\nG0 X{(min(print_bed_max[0], first_layer_print_min[0] + 32) - 32)} Y{(max(0, first_layer_print_min[1]) - 4)} Z{40} F10000\n\nM190 S[first_layer_bed_temperature] ; wait for bed temp\n\nM107\n\n;\n; MBL\n;\nM84 E ; turn off E motor\nG29 ; mesh bed leveling\nM104 S[first_layer_temperature] ; set extruder temp\nG0 X{(min(print_bed_max[0], first_layer_print_min[0] + 32) - 32)} Y{(max(0, first_layer_print_min[1]) - 4) + 4 - 4.5} Z{30} F4800\n\nM109 S[first_layer_temperature] ; wait for extruder temp\nG1 Z0.2 F720\nG92 E0\n\nM569 S0 E ; set spreadcycle mode for extruder\n\n;\n; Extrude purge line\n;\n{if filament_type[initial_tool]=="FLEX"}\nG1 E4 F2400 ; deretraction\n{else}\nG1 E2 F2400 ; deretraction\n{endif}\n\n; move right\nG1 X{(min(print_bed_max[0], first_layer_print_min[0] + 32) - 32) + 32} E{32 * 0.15} F1000\n; move down\nG1 Y{(max(0, first_layer_print_min[1]) - 4) + 4 - 4.5 - 1.5} E{1.5 * 0.15} F1000\n; move left\nG1 X{(min(print_bed_max[0], first_layer_print_min[0] + 32) - 32)} E{32 * 0.30} F800\n\nG92 E0\nM221 S100 ; set flow to 100%
+template_custom_gcode = 
+thumbnails = 16x16/QOI, 313x173/QOI, 440x240/QOI, 480x240/QOI, 640x480/PNG
+thumbnails_format = PNG
+toolchange_gcode = 
+travel_lift_before_obstacle = 0
+travel_max_lift = 1.5
+travel_ramping_lift = 1
+travel_slope = 1
+use_firmware_retraction = 0
+use_relative_e_distances = 1
+use_volumetric_e = 0
+variable_layer_height = 1
+wipe = 1
+z_offset = 0