Add missing files

filament/Devil Design PLA @ 0.25 mm.ini

@@ -0,0 +1,57 @@
+# generated by PrusaSlicer 2.4.2+linux-x64-GTK3 on 2022-06-30 at 00:43:17 UTC
+bed_temperature = 60
+bridge_fan_speed = 100
+compatible_printers = 
+compatible_printers_condition = ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
+compatible_prints = 
+compatible_prints_condition = 
+cooling = 1
+disable_fan_first_layers = 1
+end_filament_gcode = "; Filament-specific end gcode"
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 100
+filament_colour = #FF8000
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 4
+filament_cost = 20.99
+filament_density = 1.24
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_volumetric_speed = 15
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ""
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_settings_id = ""
+filament_soluble = 0
+filament_spool_weight = 250
+filament_toolchange_delay = 0
+filament_type = PLA
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_vendor = Devil Design
+filament_wipe = nil
+first_layer_bed_temperature = 60
+first_layer_temperature = 230
+full_fan_speed_layer = 4
+inherits = Devil Design PLA
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 15
+slowdown_below_layer_time = 15
+start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.05{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0"
+temperature = 220

filament/Fiberlogy - Fiber Wood.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.3.3+linux-x64-GTK3 on 2021-12-15 at 18:20:12 UTC
+# generated by PrusaSlicer 2.4.2+linux-x64-GTK3 on 2022-07-06 at 10:13:36 UTC
 bed_temperature = 60
 bridge_fan_speed = 100
 compatible_printers = 
@@ -8,7 +8,7 @@ compatible_prints_condition =
 cooling = 1
 disable_fan_first_layers = 1
 end_filament_gcode = "; Filament-specific end gcode"
-extrusion_multiplier = 0.9
+extrusion_multiplier = 1
 fan_always_on = 1
 fan_below_layer_time = 100
 filament_colour = #B59B83
@@ -22,7 +22,7 @@ filament_diameter = 1.75
 filament_load_time = 0
 filament_loading_speed = 28
 filament_loading_speed_start = 3
-filament_max_volumetric_speed = 15
+filament_max_volumetric_speed = 40
 filament_minimal_purge_on_wipe_tower = 15
 filament_notes = ""
 filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
@@ -50,7 +50,7 @@ first_layer_temperature = 200
 full_fan_speed_layer = 4
 inherits = Prusa PLA
 max_fan_speed = 100
-min_fan_speed = 100
+min_fan_speed = 70
 min_print_speed = 25
 slowdown_below_layer_time = 15
 start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.05{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0"

print/DETAIL 0.20mm @MK3.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.4.0+linux-x64-GTK3 on 2022-05-12 at 12:32:56 UTC
+# generated by PrusaSlicer 2.4.2+linux-x64-GTK3 on 2022-05-15 at 09:01:20 UTC
 avoid_crossing_perimeters = 0
 avoid_crossing_perimeters_max_detour = 0
 bottom_fill_pattern = monotonic

print/DETAIL TEST 0.10mm @0.25 nozzle MK3.ini

@@ -0,0 +1,146 @@
+# generated by PrusaSlicer 2.4.2+linux-x64-GTK3 on 2022-07-01 at 09:26:56 UTC
+avoid_crossing_perimeters = 0
+avoid_crossing_perimeters_max_detour = 0
+bottom_fill_pattern = monotonic
+bottom_solid_layers = 7
+bottom_solid_min_thickness = 0.5
+bridge_acceleration = 500
+bridge_angle = 0
+bridge_flow_ratio = 1
+bridge_speed = 20
+brim_separation = 0.1
+brim_type = outer_only
+brim_width = 0
+clip_multipart_objects = 1
+compatible_printers = 
+compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.25
+complete_objects = 0
+default_acceleration = 1000
+dont_support_bridges = 0
+draft_shield = disabled
+elefant_foot_compensation = 0
+ensure_vertical_shell_thickness = 1
+external_perimeter_extrusion_width = 0.25
+external_perimeter_speed = 20
+external_perimeters_first = 0
+extra_perimeters = 0
+extruder_clearance_height = 20
+extruder_clearance_radius = 45
+extrusion_width = 0.25
+fill_angle = 45
+fill_density = 20%
+fill_pattern = grid
+first_layer_acceleration = 500
+first_layer_acceleration_over_raft = 0
+first_layer_extrusion_width = 0.3
+first_layer_height = 0.2
+first_layer_speed = 20
+first_layer_speed_over_raft = 30
+fuzzy_skin = none
+fuzzy_skin_point_dist = 0.8
+fuzzy_skin_thickness = 0.3
+gap_fill_enabled = 1
+gap_fill_speed = 20
+gcode_comments = 0
+gcode_label_objects = 1
+gcode_resolution = 0.0125
+gcode_substitutions = 
+infill_acceleration = 1000
+infill_anchor = 2.5
+infill_anchor_max = 12
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0.25
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 25%
+infill_speed = 20
+inherits = 0.10mm DETAIL @0.25 nozzle MK3
+interface_shells = 0
+ironing = 0
+ironing_flowrate = 15%
+ironing_spacing = 0.1
+ironing_speed = 15
+ironing_type = top
+layer_height = 0.1
+max_print_speed = 80
+max_volumetric_speed = 0
+min_skirt_length = 4
+mmu_segmented_region_max_width = 0
+notes = 
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}.gcode
+overhangs = 1
+perimeter_acceleration = 500
+perimeter_extruder = 1
+perimeter_extrusion_width = 0.25
+perimeter_speed = 20
+perimeters = 3
+post_process = 
+print_settings_id = 
+raft_contact_distance = 0.07
+raft_expansion = 1.5
+raft_first_layer_density = 90%
+raft_first_layer_expansion = 3
+raft_layers = 0
+resolution = 0
+seam_position = nearest
+single_extruder_multi_material_priming = 0
+skirt_distance = 2
+skirt_height = 3
+skirts = 1
+slice_closing_radius = 0.049
+slicing_mode = regular
+small_perimeter_speed = 15
+solid_infill_below_area = 0
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0.25
+solid_infill_speed = 20
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_auto = 1
+support_material_bottom_contact_distance = 0
+support_material_bottom_interface_layers = 0
+support_material_buildplate_only = 0
+support_material_closing_radius = 2
+support_material_contact_distance = 0.1
+support_material_enforce_layers = 0
+support_material_extruder = 0
+support_material_extrusion_width = 0.25
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 0
+support_material_interface_layers = 0
+support_material_interface_pattern = rectilinear
+support_material_interface_spacing = 0.15
+support_material_interface_speed = 80%
+support_material_pattern = rectilinear
+support_material_spacing = 1
+support_material_speed = 20
+support_material_style = grid
+support_material_synchronize_layers = 0
+support_material_threshold = 50
+support_material_with_sheath = 0
+support_material_xy_spacing = 150%
+thick_bridges = 0
+thin_walls = 0
+threads = 24
+top_fill_pattern = monotonic
+top_infill_extrusion_width = 0.25
+top_solid_infill_speed = 20
+top_solid_layers = 9
+top_solid_min_thickness = 0.7
+travel_speed = 180
+travel_speed_z = 12
+wipe_tower = 1
+wipe_tower_bridging = 6
+wipe_tower_brim_width = 2
+wipe_tower_no_sparse_layers = 0
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 60
+wipe_tower_x = 170
+wipe_tower_y = 125
+xy_size_compensation = 0

print/PRINT 1.00mm @1.4 nozzle.ini

@@ -0,0 +1,146 @@
+# generated by PrusaSlicer 2.4.2+linux-x64-GTK3 on 2022-07-05 at 20:34:54 UTC
+avoid_crossing_perimeters = 0
+avoid_crossing_perimeters_max_detour = 0
+bottom_fill_pattern = monotonic
+bottom_solid_layers = 3
+bottom_solid_min_thickness = 0.8
+bridge_acceleration = 1000
+bridge_angle = 0
+bridge_flow_ratio = 0.9
+bridge_speed = 22
+brim_separation = 0.1
+brim_type = outer_only
+brim_width = 0
+clip_multipart_objects = 1
+compatible_printers = 
+compatible_printers_condition = printer_model=~/(MK3|MK2.5).*/ and nozzle_diameter[0]==1.4 and num_extruders==1
+complete_objects = 0
+default_acceleration = 1000
+dont_support_bridges = 0
+draft_shield = disabled
+elefant_foot_compensation = 0.2
+ensure_vertical_shell_thickness = 1
+external_perimeter_extrusion_width = 1.5
+external_perimeter_speed = 20
+external_perimeters_first = 0
+extra_perimeters = 0
+extruder_clearance_height = 20
+extruder_clearance_radius = 45
+extrusion_width = 1.5
+fill_angle = 45
+fill_density = 10%
+fill_pattern = gyroid
+first_layer_acceleration = 800
+first_layer_acceleration_over_raft = 0
+first_layer_extrusion_width = 1.5
+first_layer_height = 0.3
+first_layer_speed = 20
+first_layer_speed_over_raft = 30
+fuzzy_skin = none
+fuzzy_skin_point_dist = 0.8
+fuzzy_skin_thickness = 0.3
+gap_fill_enabled = 1
+gap_fill_speed = 25
+gcode_comments = 0
+gcode_label_objects = 1
+gcode_resolution = 0.0125
+gcode_substitutions = 
+infill_acceleration = 1000
+infill_anchor = 2.5
+infill_anchor_max = 20
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 1.5
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 30%
+infill_speed = 35
+inherits = 0.40mm QUALITY @0.8 nozzle
+interface_shells = 0
+ironing = 0
+ironing_flowrate = 15%
+ironing_spacing = 0.1
+ironing_speed = 15
+ironing_type = top
+layer_height = 1
+max_print_speed = 50
+max_volumetric_speed = 0
+min_skirt_length = 4
+mmu_segmented_region_max_width = 0
+notes = 
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}.gcode
+overhangs = 0
+perimeter_acceleration = 800
+perimeter_extruder = 1
+perimeter_extrusion_width = 1.5
+perimeter_speed = 30
+perimeters = 2
+post_process = 
+print_settings_id = 
+raft_contact_distance = 0.2
+raft_expansion = 1.5
+raft_first_layer_density = 90%
+raft_first_layer_expansion = 3
+raft_layers = 0
+resolution = 0
+seam_position = rear
+single_extruder_multi_material_priming = 0
+skirt_distance = 3
+skirt_height = 2
+skirts = 1
+slice_closing_radius = 0.049
+slicing_mode = regular
+small_perimeter_speed = 20
+solid_infill_below_area = 0
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 1.5
+solid_infill_speed = 35
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_auto = 1
+support_material_bottom_contact_distance = 0
+support_material_bottom_interface_layers = 0
+support_material_buildplate_only = 0
+support_material_closing_radius = 2
+support_material_contact_distance = 0.25
+support_material_enforce_layers = 0
+support_material_extruder = 0
+support_material_extrusion_width = 0.7
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 0
+support_material_interface_layers = 2
+support_material_interface_pattern = rectilinear
+support_material_interface_spacing = 0.4
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 35
+support_material_style = grid
+support_material_synchronize_layers = 0
+support_material_threshold = 50
+support_material_with_sheath = 0
+support_material_xy_spacing = 80%
+thick_bridges = 1
+thin_walls = 0
+threads = 24
+top_fill_pattern = monotonic
+top_infill_extrusion_width = 1.4
+top_solid_infill_speed = 30
+top_solid_layers = 3
+top_solid_min_thickness = 1.2
+travel_speed = 180
+travel_speed_z = 12
+wipe_tower = 1
+wipe_tower_bridging = 10
+wipe_tower_brim_width = 2
+wipe_tower_no_sparse_layers = 0
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 60
+wipe_tower_x = 170
+wipe_tower_y = 140
+xy_size_compensation = 0

print/QUALITY 0.30mm @1.4 nozzle.ini

@@ -0,0 +1,146 @@
+# generated by PrusaSlicer 2.4.2+linux-x64-GTK3 on 2022-07-06 at 07:55:13 UTC
+avoid_crossing_perimeters = 1
+avoid_crossing_perimeters_max_detour = 0
+bottom_fill_pattern = monotonic
+bottom_solid_layers = 3
+bottom_solid_min_thickness = 0.8
+bridge_acceleration = 1000
+bridge_angle = 0
+bridge_flow_ratio = 0.9
+bridge_speed = 22
+brim_separation = 0.1
+brim_type = outer_only
+brim_width = 0
+clip_multipart_objects = 1
+compatible_printers = 
+compatible_printers_condition = printer_model=~/(MK3|MK2.5).*/ and nozzle_diameter[0]==1.4 and num_extruders==1
+complete_objects = 0
+default_acceleration = 1000
+dont_support_bridges = 0
+draft_shield = disabled
+elefant_foot_compensation = 0.2
+ensure_vertical_shell_thickness = 1
+external_perimeter_extrusion_width = 1.5
+external_perimeter_speed = 25
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 45
+extrusion_width = 1.5
+fill_angle = 45
+fill_density = 15%
+fill_pattern = gyroid
+first_layer_acceleration = 800
+first_layer_acceleration_over_raft = 0
+first_layer_extrusion_width = 1.5
+first_layer_height = 0.3
+first_layer_speed = 20
+first_layer_speed_over_raft = 30
+fuzzy_skin = none
+fuzzy_skin_point_dist = 0.8
+fuzzy_skin_thickness = 0.3
+gap_fill_enabled = 1
+gap_fill_speed = 30
+gcode_comments = 0
+gcode_label_objects = 1
+gcode_resolution = 0.0125
+gcode_substitutions = 
+infill_acceleration = 1000
+infill_anchor = 2.5
+infill_anchor_max = 20
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 1.5
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 30%
+infill_speed = 50
+inherits = 0.40mm QUALITY @0.8 nozzle
+interface_shells = 0
+ironing = 0
+ironing_flowrate = 15%
+ironing_spacing = 0.1
+ironing_speed = 15
+ironing_type = top
+layer_height = 0.3
+max_print_speed = 50
+max_volumetric_speed = 0
+min_skirt_length = 4
+mmu_segmented_region_max_width = 0
+notes = 
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}.gcode
+overhangs = 1
+perimeter_acceleration = 800
+perimeter_extruder = 1
+perimeter_extrusion_width = 1.5
+perimeter_speed = 35
+perimeters = 2
+post_process = 
+print_settings_id = 
+raft_contact_distance = 0.2
+raft_expansion = 1.5
+raft_first_layer_density = 90%
+raft_first_layer_expansion = 3
+raft_layers = 0
+resolution = 0
+seam_position = nearest
+single_extruder_multi_material_priming = 0
+skirt_distance = 3
+skirt_height = 2
+skirts = 1
+slice_closing_radius = 0.049
+slicing_mode = regular
+small_perimeter_speed = 25
+solid_infill_below_area = 0
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 1.5
+solid_infill_speed = 45
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_auto = 1
+support_material_bottom_contact_distance = 0
+support_material_bottom_interface_layers = 0
+support_material_buildplate_only = 0
+support_material_closing_radius = 2
+support_material_contact_distance = 0.25
+support_material_enforce_layers = 0
+support_material_extruder = 0
+support_material_extrusion_width = 0.7
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 0
+support_material_interface_layers = 2
+support_material_interface_pattern = rectilinear
+support_material_interface_spacing = 0.4
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 40
+support_material_style = grid
+support_material_synchronize_layers = 0
+support_material_threshold = 50
+support_material_with_sheath = 0
+support_material_xy_spacing = 80%
+thick_bridges = 1
+thin_walls = 1
+threads = 24
+top_fill_pattern = monotonic
+top_infill_extrusion_width = 1.4
+top_solid_infill_speed = 35
+top_solid_layers = 4
+top_solid_min_thickness = 1.2
+travel_speed = 180
+travel_speed_z = 12
+wipe_tower = 1
+wipe_tower_bridging = 10
+wipe_tower_brim_width = 2
+wipe_tower_no_sparse_layers = 0
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 60
+wipe_tower_x = 170
+wipe_tower_y = 140
+xy_size_compensation = 0

print/QUALITY 0.40mm @1.0 nozzle.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.4.0+linux-x64-GTK3 on 2022-05-06 at 20:10:26 UTC
+# generated by PrusaSlicer 2.4.2+linux-x64-GTK3 on 2022-05-09 at 22:10:04 UTC
 avoid_crossing_perimeters = 0
 avoid_crossing_perimeters_max_detour = 0
 bottom_fill_pattern = monotonic
@@ -28,7 +28,7 @@ extruder_clearance_height = 20
 extruder_clearance_radius = 45
 extrusion_width = 1.1
 fill_angle = 45
-fill_density = 0%
+fill_density = 10%
 fill_pattern = gyroid
 first_layer_acceleration = 800
 first_layer_acceleration_over_raft = 0
@@ -44,6 +44,7 @@ gap_fill_speed = 30
 gcode_comments = 0
 gcode_label_objects = 1
 gcode_resolution = 0.0125
+gcode_substitutions = 
 infill_acceleration = 1000
 infill_anchor = 2.5
 infill_anchor_max = 20

print/QUALITY 0.40mm @1.4 nozzle.ini

@@ -0,0 +1,146 @@
+# generated by PrusaSlicer 2.4.2+linux-x64-GTK3 on 2022-06-24 at 12:25:07 UTC
+avoid_crossing_perimeters = 0
+avoid_crossing_perimeters_max_detour = 0
+bottom_fill_pattern = monotonic
+bottom_solid_layers = 3
+bottom_solid_min_thickness = 0.8
+bridge_acceleration = 1000
+bridge_angle = 0
+bridge_flow_ratio = 0.9
+bridge_speed = 22
+brim_separation = 0.1
+brim_type = outer_only
+brim_width = 0
+clip_multipart_objects = 1
+compatible_printers = 
+compatible_printers_condition = printer_model=~/(MK3|MK2.5).*/ and nozzle_diameter[0]==1.4 and num_extruders==1
+complete_objects = 0
+default_acceleration = 1000
+dont_support_bridges = 0
+draft_shield = disabled
+elefant_foot_compensation = 0.2
+ensure_vertical_shell_thickness = 1
+external_perimeter_extrusion_width = 1.5
+external_perimeter_speed = 25
+external_perimeters_first = 0
+extra_perimeters = 0
+extruder_clearance_height = 20
+extruder_clearance_radius = 45
+extrusion_width = 1.5
+fill_angle = 45
+fill_density = 10%
+fill_pattern = gyroid
+first_layer_acceleration = 800
+first_layer_acceleration_over_raft = 0
+first_layer_extrusion_width = 1.5
+first_layer_height = 0.3
+first_layer_speed = 20
+first_layer_speed_over_raft = 30
+fuzzy_skin = none
+fuzzy_skin_point_dist = 0.8
+fuzzy_skin_thickness = 0.3
+gap_fill_enabled = 1
+gap_fill_speed = 30
+gcode_comments = 0
+gcode_label_objects = 1
+gcode_resolution = 0.0125
+gcode_substitutions = 
+infill_acceleration = 1000
+infill_anchor = 2.5
+infill_anchor_max = 20
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 1.5
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 30%
+infill_speed = 50
+inherits = 0.40mm QUALITY @0.8 nozzle
+interface_shells = 0
+ironing = 0
+ironing_flowrate = 15%
+ironing_spacing = 0.1
+ironing_speed = 15
+ironing_type = top
+layer_height = 0.4
+max_print_speed = 50
+max_volumetric_speed = 0
+min_skirt_length = 4
+mmu_segmented_region_max_width = 0
+notes = 
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}.gcode
+overhangs = 0
+perimeter_acceleration = 800
+perimeter_extruder = 1
+perimeter_extrusion_width = 1.5
+perimeter_speed = 35
+perimeters = 2
+post_process = 
+print_settings_id = 
+raft_contact_distance = 0.2
+raft_expansion = 1.5
+raft_first_layer_density = 90%
+raft_first_layer_expansion = 3
+raft_layers = 0
+resolution = 0
+seam_position = nearest
+single_extruder_multi_material_priming = 0
+skirt_distance = 3
+skirt_height = 2
+skirts = 1
+slice_closing_radius = 0.049
+slicing_mode = regular
+small_perimeter_speed = 25
+solid_infill_below_area = 0
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 1.5
+solid_infill_speed = 45
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_auto = 1
+support_material_bottom_contact_distance = 0
+support_material_bottom_interface_layers = 0
+support_material_buildplate_only = 0
+support_material_closing_radius = 2
+support_material_contact_distance = 0.25
+support_material_enforce_layers = 0
+support_material_extruder = 0
+support_material_extrusion_width = 0.7
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 0
+support_material_interface_layers = 2
+support_material_interface_pattern = rectilinear
+support_material_interface_spacing = 0.4
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 40
+support_material_style = grid
+support_material_synchronize_layers = 0
+support_material_threshold = 50
+support_material_with_sheath = 0
+support_material_xy_spacing = 80%
+thick_bridges = 1
+thin_walls = 0
+threads = 24
+top_fill_pattern = monotonic
+top_infill_extrusion_width = 1.4
+top_solid_infill_speed = 35
+top_solid_layers = 4
+top_solid_min_thickness = 1.2
+travel_speed = 180
+travel_speed_z = 12
+wipe_tower = 1
+wipe_tower_bridging = 10
+wipe_tower_brim_width = 2
+wipe_tower_no_sparse_layers = 0
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 60
+wipe_tower_x = 170
+wipe_tower_y = 140
+xy_size_compensation = 0

print/TEST 1.20mm @1.4 nozzle.ini

@@ -0,0 +1,146 @@
+# generated by PrusaSlicer 2.4.2+linux-x64-GTK3 on 2022-07-02 at 16:47:21 UTC
+avoid_crossing_perimeters = 0
+avoid_crossing_perimeters_max_detour = 0
+bottom_fill_pattern = monotonic
+bottom_solid_layers = 3
+bottom_solid_min_thickness = 0.8
+bridge_acceleration = 1000
+bridge_angle = 0
+bridge_flow_ratio = 0.9
+bridge_speed = 20
+brim_separation = 0.1
+brim_type = outer_only
+brim_width = 0
+clip_multipart_objects = 1
+compatible_printers = 
+compatible_printers_condition = printer_model=~/(MK3|MK2.5).*/ and nozzle_diameter[0]==1.4 and num_extruders==1
+complete_objects = 0
+default_acceleration = 1000
+dont_support_bridges = 0
+draft_shield = disabled
+elefant_foot_compensation = 0.2
+ensure_vertical_shell_thickness = 1
+external_perimeter_extrusion_width = 1.5
+external_perimeter_speed = 15
+external_perimeters_first = 0
+extra_perimeters = 0
+extruder_clearance_height = 20
+extruder_clearance_radius = 45
+extrusion_width = 1.5
+fill_angle = 45
+fill_density = 10%
+fill_pattern = gyroid
+first_layer_acceleration = 800
+first_layer_acceleration_over_raft = 0
+first_layer_extrusion_width = 1.5
+first_layer_height = 0.3
+first_layer_speed = 20
+first_layer_speed_over_raft = 30
+fuzzy_skin = none
+fuzzy_skin_point_dist = 0.8
+fuzzy_skin_thickness = 0.3
+gap_fill_enabled = 1
+gap_fill_speed = 20
+gcode_comments = 0
+gcode_label_objects = 1
+gcode_resolution = 0.0125
+gcode_substitutions = 
+infill_acceleration = 1000
+infill_anchor = 2.5
+infill_anchor_max = 20
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 1.5
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 30%
+infill_speed = 22
+inherits = 0.40mm QUALITY @0.8 nozzle
+interface_shells = 0
+ironing = 0
+ironing_flowrate = 15%
+ironing_spacing = 0.1
+ironing_speed = 15
+ironing_type = top
+layer_height = 1.2
+max_print_speed = 50
+max_volumetric_speed = 0
+min_skirt_length = 4
+mmu_segmented_region_max_width = 0
+notes = 
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}.gcode
+overhangs = 0
+perimeter_acceleration = 800
+perimeter_extruder = 1
+perimeter_extrusion_width = 1.5
+perimeter_speed = 22
+perimeters = 2
+post_process = 
+print_settings_id = 
+raft_contact_distance = 0.2
+raft_expansion = 1.5
+raft_first_layer_density = 90%
+raft_first_layer_expansion = 3
+raft_layers = 0
+resolution = 0
+seam_position = nearest
+single_extruder_multi_material_priming = 0
+skirt_distance = 3
+skirt_height = 2
+skirts = 1
+slice_closing_radius = 0.049
+slicing_mode = regular
+small_perimeter_speed = 15
+solid_infill_below_area = 0
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 1.5
+solid_infill_speed = 22
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_auto = 1
+support_material_bottom_contact_distance = 0
+support_material_bottom_interface_layers = 0
+support_material_buildplate_only = 0
+support_material_closing_radius = 2
+support_material_contact_distance = 0.25
+support_material_enforce_layers = 0
+support_material_extruder = 0
+support_material_extrusion_width = 0.7
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 0
+support_material_interface_layers = 2
+support_material_interface_pattern = rectilinear
+support_material_interface_spacing = 0.4
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 22
+support_material_style = grid
+support_material_synchronize_layers = 0
+support_material_threshold = 50
+support_material_with_sheath = 0
+support_material_xy_spacing = 80%
+thick_bridges = 1
+thin_walls = 0
+threads = 24
+top_fill_pattern = monotonic
+top_infill_extrusion_width = 1.4
+top_solid_infill_speed = 20
+top_solid_layers = 4
+top_solid_min_thickness = 1.2
+travel_speed = 180
+travel_speed_z = 12
+wipe_tower = 1
+wipe_tower_bridging = 10
+wipe_tower_brim_width = 2
+wipe_tower_no_sparse_layers = 0
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 60
+wipe_tower_x = 170
+wipe_tower_y = 140
+xy_size_compensation = 0

print/WOOD 0.30mm @1.4 nozzle.ini

@@ -0,0 +1,146 @@
+# generated by PrusaSlicer 2.4.2+linux-x64-GTK3 on 2022-07-06 at 10:01:58 UTC
+avoid_crossing_perimeters = 1
+avoid_crossing_perimeters_max_detour = 0
+bottom_fill_pattern = monotonic
+bottom_solid_layers = 3
+bottom_solid_min_thickness = 0.8
+bridge_acceleration = 1000
+bridge_angle = 0
+bridge_flow_ratio = 0.9
+bridge_speed = 40
+brim_separation = 0.1
+brim_type = outer_only
+brim_width = 0
+clip_multipart_objects = 1
+compatible_printers = 
+compatible_printers_condition = printer_model=~/(MK3|MK2.5).*/ and nozzle_diameter[0]==1.4 and num_extruders==1
+complete_objects = 0
+default_acceleration = 1000
+dont_support_bridges = 0
+draft_shield = disabled
+elefant_foot_compensation = 0.2
+ensure_vertical_shell_thickness = 1
+external_perimeter_extrusion_width = 1.5
+external_perimeter_speed = 70%
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 45
+extrusion_width = 1.5
+fill_angle = 45
+fill_density = 0%
+fill_pattern = gyroid
+first_layer_acceleration = 800
+first_layer_acceleration_over_raft = 0
+first_layer_extrusion_width = 1.5
+first_layer_height = 0.3
+first_layer_speed = 35
+first_layer_speed_over_raft = 30
+fuzzy_skin = none
+fuzzy_skin_point_dist = 0.8
+fuzzy_skin_thickness = 0.3
+gap_fill_enabled = 1
+gap_fill_speed = 40
+gcode_comments = 0
+gcode_label_objects = 1
+gcode_resolution = 0.0125
+gcode_substitutions = 
+infill_acceleration = 1000
+infill_anchor = 2.5
+infill_anchor_max = 20
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 1.5
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 30%
+infill_speed = 50
+inherits = 0.40mm QUALITY @0.8 nozzle
+interface_shells = 0
+ironing = 0
+ironing_flowrate = 15%
+ironing_spacing = 0.1
+ironing_speed = 15
+ironing_type = top
+layer_height = 0.3
+max_print_speed = 100
+max_volumetric_speed = 40
+min_skirt_length = 4
+mmu_segmented_region_max_width = 0
+notes = 
+only_retract_when_crossing_perimeters = 0
+ooze_prevention = 0
+output_filename_format = {input_filename_base}_{nozzle_diameter[0]}n_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}.gcode
+overhangs = 1
+perimeter_acceleration = 800
+perimeter_extruder = 1
+perimeter_extrusion_width = 1.5
+perimeter_speed = 50
+perimeters = 2
+post_process = 
+print_settings_id = 
+raft_contact_distance = 0.2
+raft_expansion = 1.5
+raft_first_layer_density = 90%
+raft_first_layer_expansion = 3
+raft_layers = 0
+resolution = 0
+seam_position = nearest
+single_extruder_multi_material_priming = 0
+skirt_distance = 3
+skirt_height = 2
+skirts = 1
+slice_closing_radius = 0.049
+slicing_mode = close_holes
+small_perimeter_speed = 70%
+solid_infill_below_area = 0
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 1.5
+solid_infill_speed = 90%
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_auto = 1
+support_material_bottom_contact_distance = 0
+support_material_bottom_interface_layers = 0
+support_material_buildplate_only = 0
+support_material_closing_radius = 2
+support_material_contact_distance = 0.25
+support_material_enforce_layers = 0
+support_material_extruder = 0
+support_material_extrusion_width = 0.7
+support_material_interface_contact_loops = 0
+support_material_interface_extruder = 0
+support_material_interface_layers = 2
+support_material_interface_pattern = rectilinear
+support_material_interface_spacing = 0.4
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 40
+support_material_style = grid
+support_material_synchronize_layers = 0
+support_material_threshold = 50
+support_material_with_sheath = 0
+support_material_xy_spacing = 80%
+thick_bridges = 1
+thin_walls = 1
+threads = 24
+top_fill_pattern = monotonic
+top_infill_extrusion_width = 1.4
+top_solid_infill_speed = 70%
+top_solid_layers = 4
+top_solid_min_thickness = 1.2
+travel_speed = 180
+travel_speed_z = 12
+wipe_tower = 1
+wipe_tower_bridging = 10
+wipe_tower_brim_width = 2
+wipe_tower_no_sparse_layers = 0
+wipe_tower_rotation_angle = 0
+wipe_tower_width = 60
+wipe_tower_x = 170
+wipe_tower_y = 140
+xy_size_compensation = 0

printer/Original Prusa i3 MK3S & MK3S+ 1.4 nozzle.ini

@@ -0,0 +1,78 @@
+# generated by PrusaSlicer 2.4.2+linux-x64-GTK3 on 2022-07-02 at 16:49:07 UTC
+bed_custom_model = 
+bed_custom_texture = 
+bed_shape = 0x0,250x0,250x210,0x210
+before_layer_gcode = ;BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n
+between_objects_gcode = 
+color_change_gcode = M600\nG1 E0.6 F1500 ; prime after color change
+cooling_tube_length = 5
+cooling_tube_retraction = 91.5
+default_filament_profile = "Prusament PLA @0.8 nozzle"
+default_print_profile = 0.40mm QUALITY @0.8 nozzle
+deretract_speed = 0
+end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nG1 X0 Y200 F3600 ; park\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+49, max_print_height)} F720 ; Move print head further up{endif}\nG4 ; wait\nM221 S100 ; reset flow\nM900 K0 ; reset LA\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3|@0.25 nozzle MK3).*/}M907 E538 ; reset extruder motor current{endif}\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nM84 ; disable motors
+extra_loading_move = -2
+extruder_colour = ""
+extruder_offset = 0x0
+gcode_flavor = marlin
+high_current_on_filament_swap = 0
+host_type = octoprint
+inherits = Original Prusa i3 MK3S & MK3S+ 0.8 nozzle
+layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
+machine_limits_usage = emit_to_gcode
+machine_max_acceleration_e = 5000,5000
+machine_max_acceleration_extruding = 1250,1250
+machine_max_acceleration_retracting = 1250,1250
+machine_max_acceleration_travel = 1500,1250
+machine_max_acceleration_x = 1000,960
+machine_max_acceleration_y = 1000,960
+machine_max_acceleration_z = 200,200
+machine_max_feedrate_e = 120,120
+machine_max_feedrate_x = 200,100
+machine_max_feedrate_y = 200,100
+machine_max_feedrate_z = 12,12
+machine_max_jerk_e = 4.5,4.5
+machine_max_jerk_x = 8,8
+machine_max_jerk_y = 8,8
+machine_max_jerk_z = 0.4,0.4
+machine_min_extruding_rate = 0,0
+machine_min_travel_rate = 0,0
+max_layer_height = 0.6
+max_print_height = 210
+min_layer_height = 0.2
+nozzle_diameter = 1.4
+parking_pos_retraction = 92
+pause_print_gcode = M601
+print_host = 
+printer_model = MK3S
+printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK3\n
+printer_settings_id = 
+printer_technology = FFF
+printer_variant = 0.8
+printer_vendor = 
+printhost_apikey = 
+printhost_cafile = 
+remaining_times = 1
+retract_before_travel = 1
+retract_before_wipe = 0%
+retract_layer_change = 1
+retract_length = 1
+retract_length_toolchange = 4
+retract_lift = 2
+retract_lift_above = 0
+retract_lift_below = 209
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 35
+silent_mode = 1
+single_extruder_multi_material = 0
+start_gcode = M862.3 P "[printer_model]" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Z0.2 F720\nG1 Y-3 F1000 ; go outside print area\nG92 E0\nG1 X60 E9 F1000 ; intro line\nG1 X100 E12.5 F1000 ; intro line\nG92 E0\nM221 S95
+template_custom_gcode = 
+thumbnails = 160x120
+toolchange_gcode = 
+use_firmware_retraction = 0
+use_relative_e_distances = 1
+use_volumetric_e = 0
+variable_layer_height = 1
+wipe = 1
+z_offset = 0