mirror of
https://github.com/pgrondek/prusa-slicer-profiles.git
synced 2024-11-22 20:33:44 +00:00
76 lines
3.1 KiB
INI
76 lines
3.1 KiB
INI
# generated by PrusaSlicer 2.7.3 on 2024-04-05 at 07:39:17 UTC
|
|
bed_temperature = 100
|
|
bridge_fan_speed = 60
|
|
compatible_printers =
|
|
compatible_printers_condition = printer_notes=~/.*MK4.*/ and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 5
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode"
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #FF8000
|
|
filament_cooling_final_speed = 1
|
|
filament_cooling_initial_speed = 2
|
|
filament_cooling_moves = 1
|
|
filament_cost = 20
|
|
filament_density = 1.27
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 15
|
|
filament_loading_speed = 14
|
|
filament_loading_speed_start = 19
|
|
filament_max_volumetric_speed = 10
|
|
filament_minimal_purge_on_wipe_tower = 35
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_purge_multiplier = 100%
|
|
filament_ramming_parameters = "120 140 4.70968 4.74194 4.77419 4.80645 4.83871 4.87097 4.90323 5 5.25806 5.67742 6.29032 7.06452 7.83871 8.3871| 0.05 4.72901 0.45 4.73545 0.95 4.83226 1.45 4.88067 1.95 5.05483 2.45 5.93553 2.95 7.53556 3.45 8.6323 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = 0%
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = 1
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = 0.15
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 330
|
|
filament_stamping_distance = 0
|
|
filament_stamping_loading_speed = 20
|
|
filament_toolchange_delay = 0
|
|
filament_travel_lift_before_obstacle = nil
|
|
filament_travel_max_lift = nil
|
|
filament_travel_ramping_lift = nil
|
|
filament_travel_slope = nil
|
|
filament_type = PETG
|
|
filament_unload_time = 12
|
|
filament_unloading_speed = 20
|
|
filament_unloading_speed_start = 120
|
|
filament_vendor = Fiberlogy
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 100
|
|
first_layer_temperature = 250
|
|
full_fan_speed_layer = 5
|
|
idle_temperature = 70
|
|
inherits = Fiberlogy Easy PET-G @PG
|
|
max_fan_speed = 25
|
|
min_fan_speed = 0
|
|
min_print_speed = 15
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 9
|
|
start_filament_gcode = "M900 K{if nozzle_diameter[0]==0.4}0.07{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.09{elsif nozzle_diameter[0]==0.35}0.08{elsif nozzle_diameter[0]==0.6}0.04{elsif nozzle_diameter[0]==0.5}0.05{elsif nozzle_diameter[0]==0.8}0.02{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS).*/}\nM572 S{if nozzle_diameter[0]==0.4}0.055{elsif nozzle_diameter[0]==0.5}0.042{elsif nozzle_diameter[0]==0.6}0.032{elsif nozzle_diameter[0]==0.8}0.018{elsif nozzle_diameter[0]==0.25}0.18{elsif nozzle_diameter[0]==0.3}0.1{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S36 ; set heatbreak target temp"
|
|
temperature = 250
|