Luc Van Daele
0e4b6b373d
[1.1.x] G33 magic numbers ( #8173 )
...
* [1.1.x] G33 magic numbers
* oops
* comments
* oops
* warning
* better comment section
* remarks
* extra grids
2017-11-03 03:35:53 -05:00
Scott Lahteine
193a0e9273
pid_autotune parity with 2.0.x
2017-11-03 03:26:47 -05:00
Rowan Meara
39cc36d3f1
[1.1.x] M303 thermal runaway protection ( #8209 )
...
* Added M303 thermal runaway protection
Currently, thermal runaway protection is not available during M303.
Therefore, if someone plugs the thermistors in incorrectly and goes to
autotune their printer, the printer temperature could runaway and damage
could occur.
* Replace removed line, clarifying its logic
2017-11-03 03:16:39 -05:00
Scott Lahteine
87d3a1ae4d
Merge pull request #8228 from tcm0116/1.0.x-dual_stepper
...
[1.1.x] Fix automatic stepper assignment for X/Y/Z dual stepper drivers
2017-11-03 03:08:43 -05:00
AnHardt
dcd7949544
Fix watchdog in WATCHDOG_RESET_MANUAL mode AVR
2017-11-03 04:45:13 +01:00
Thomas Moore
277eb16d67
Fix automatic stepper assignment for X/Y/Z dual stepper drivers
2017-11-02 18:50:25 -05:00
jmdearras
c9980c0a5c
Restore MKS_GEN_L
...
Removed by accident, I presume, when the file was cleaned up
2017-11-02 12:14:54 -04:00
jmdearras
3e9504d306
Fix case light "off" function ( #8205 )
...
* Fix case light "off" function
It would only turn the light off if brightness was 255
* Update Marlin_main.cpp
2017-11-01 21:17:23 -05:00
Scott Lahteine
4bf0e15653
Allow asterisks in G-Code commands
...
Addressing #6655
2017-10-31 21:14:56 -05:00
Scott Lahteine
f02ca2a9a3
Organize boards.h by architecture
2017-10-31 16:12:07 -05:00
Scott Lahteine
4fb3ce4739
Support for SilverGate Board
2017-10-31 15:26:27 -05:00
Scott Lahteine
db6de76acb
Only show custom bootscreen once
2017-10-31 01:52:35 -05:00
GMagician
15be1cb9a9
[1.1.x] Fix NO_MOTION_BEFORE_HOMING unwanted behaviour ( #8177 )
...
* [1.1.x] Fix NO_MOTION_BEFORE_HOMING unwanted behaviour
NO_MOTION_BEFORE_HOMING should prevent XYZ movements only when homing is not done.
E axes should be allowed
* Update Marlin_main.cpp
* Update Marlin_main.cpp
* Update Marlin_main.cpp
2017-10-30 22:50:50 -05:00
Scott Lahteine
893092ff7f
Kinematic clamp_to_software_endstops
2017-10-30 16:24:45 -05:00
Scott Lahteine
8b7c1e9cec
Fix for MAX_VFAT_ENTRIES sanity check
2017-10-30 16:24:45 -05:00
Scott Lahteine
393ceb28fc
The plural of 'axis' is 'axes'
2017-10-30 14:49:51 -05:00
Scott Lahteine
d9cb7be444
Merge pull request #8160 from thinkyhead/bf1_fixup_sd_reprint
...
[1.1.x] Simplify SD_REPRINT_LAST_SELECTED_FILE
2017-10-29 23:57:44 -05:00
Scott Lahteine
5837f067cf
Tweak to QUICK_HOME comment
2017-10-29 23:50:02 -05:00
Scott Lahteine
5e5a177934
No hacks needed for SD_REPRINT_LAST_SELECTED_FILE
2017-10-29 22:44:03 -05:00
Scott Lahteine
0b5b03d9dc
Tweak for soft endstops
2017-10-29 20:16:22 -05:00
Scott Lahteine
9288d80613
Merge pull request #8156 from thinkyhead/bf1_anet_10_servo
...
[1.1.x] Define a default SERVO0_PIN for Anet 1.0
2017-10-29 19:53:49 -05:00
Scott Lahteine
6698db29de
Update LCD draw condition
2017-10-29 19:17:32 -05:00
Scott Lahteine
25e86a520d
Merge pull request #8114 from thinkyhead/bf1_print_sd_file_again
...
[1.1.x] Cleanup for SD Print Again
2017-10-29 19:09:34 -05:00
Scott Lahteine
b0e282a74b
Cleanups for SD_REPRINT_LAST_SELECTED_FILE
2017-10-29 19:02:17 -05:00
Scott Lahteine
46ed54cd8e
Include time scale in some planner vars
2017-10-29 18:48:14 -05:00
Scott Lahteine
9c870baf84
Add a hidden 8s watchdog option for easier debugging
2017-10-29 18:34:57 -05:00
Scott Lahteine
471c2b5d5c
Provide a default SERVO0_PIN for Anet 1.0
2017-10-29 18:34:57 -05:00
Scott Lahteine
e792c2b234
Followup to #8123 - to match 2.0.x changes
2017-10-29 05:39:44 -05:00
Scott Lahteine
daa85f71e1
Merge pull request #8123 from thinkyhead/bf1_dual_xyz_endstops
...
[1.1.x] Dual endstops XYZ
2017-10-29 04:36:09 -05:00
Rowan Meara
9850ba0cbd
[1.1.x] Fix M303 thermal protection #8103 ( #8126 )
...
* Fixed M303 thermal protection
The temperature sanity checking logic was not being applied during M303
(pid autotuning) because instead of setting a target temperature, it
directly manipulated the pwm values. When PIDTEMP/PIDTEMPBED is
enabled, PWM values rather than the target temperature determine whether
the heater is on. I changed this to look directly at the PWM amount
when pid is enabled.
* Turn off heaters on M303 error
Currently, PID autotuning stops if it overshoots the temperature by 20C
or if if the temperature does not change for 20 minutes and it times
out. I added calls to disable the heaters in these scenarios.
* Removed unnecessary if statement.
Added changes suggested by GMagician.
* Update temperature.cpp
* Update temperature.cpp
* Update temperature.cpp
2017-10-29 04:34:47 -05:00
Scott Lahteine
318c419f77
Implement support for Dual X and Y endstops
2017-10-29 03:49:45 -05:00
Scott Lahteine
7e1232269a
Add Dual Steppers / Endstops to configs
2017-10-29 03:49:45 -05:00
Scott Lahteine
62d52d62dc
Cleanup for DIGIPOTS settings
2017-10-29 03:49:32 -05:00
LVD-AC
77cf42588f
(1.1.x) serious bug G33
2017-10-29 00:22:55 +02:00
Scott Lahteine
a979c428ee
Revert default BABYSTEP_MULTIPLICATOR to 1
2017-10-27 19:42:51 -05:00
jmdearras
6920769a9a
Added MKS GEN L board ( #8088 )
...
[1.1.x] Add MKS GEN L board
2017-10-27 02:13:41 -05:00
Scott Lahteine
410aa0716d
Concise SD_REPRINT_LAST_SELECTED_FILE description
2017-10-27 00:10:04 -05:00
Scott Lahteine
445a7f65cd
Clean up trailing whitespace
2017-10-27 00:02:35 -05:00
Luc Van Daele
e64cfb13b8
(1.1.x) auto tune calibration parameters ( #8031 )
...
* auto tune calibration parameters
* solve warnings
* Tweaks to formatting
* review Thinkyhead
* Error
2017-10-26 23:49:20 -05:00
Scott Lahteine
2296d98845
Tweak neopixel self-test
2017-10-26 22:46:11 -05:00
Scott Lahteine
9aac3d8773
Add some Polish translations
...
Thanks @SCiunczyk
2017-10-26 22:44:23 -05:00
Scott Lahteine
6569b9ba56
Fix FWRETRACT logic, apply common sense
2017-10-26 22:36:41 -05:00
Bob-the-Kuhn
7ab9abe4ef
Merge pull request #8107 from Bob-the-Kuhn/1.1.x-reduced-font-fix
...
(bug fix) 1.1.x - save 1400 bytes of FLASH by using reduced font for some languages
2017-10-26 16:09:52 -05:00
Bob-the-Kuhn
3357170b18
give this language an unique name
2017-10-26 15:48:00 -05:00
Roxy-3D
2e746f2b8b
Initial conflict resolution of SD_REPRINT_LAST_SELECTED_FILE ( #8104 )
...
* Initial conflict resolution
All previous items resolved:
- Use of ELAPSED() on timer code
- Switch to use of defer_return_to_status=true as much as possible
- Update & Clean Up of Max7219 routines
* Resolve non-SD case in ultralcd.cpp
2017-10-26 11:44:55 -05:00
Bob-the-Kuhn
594c075377
1.1.x - save 1400 bytes of FLASH by using reduced font for some languages ( #8095 )
...
* use reduced sized font for some languages
* Fit Portuguese language files to existing scheme
* Rename language_pl-DOGM.h to language_pl_utf8.h
* Rename language_pl_utf8.h to language_pl-DOGM.h
* Update dogm_font_data_ISO10646_1.h
* Update dogm_font_data_ISO10646_1.h
2017-10-25 18:32:38 -05:00
Scott Lahteine
8bb1e91afd
More specific M100 description
2017-10-25 16:11:09 -05:00
Scott Lahteine
a12d1b21b5
Merge pull request #8048 from madmo/mks-mini-gt2560
...
[1.1.x] Add MKS MINI 12864 support to GT2560
2017-10-25 01:13:07 -05:00
Scott Lahteine
5bed2f351a
Fix spacing, use single instances of similar pins
2017-10-24 19:12:40 -05:00
Scott Lahteine
ec9d7b639d
Encourage users to re-examine their configs
2017-10-24 18:33:31 -05:00
