Variant file for MK2 + cond. translation

Firmware/Configuration_prusa.h

@@ -6,22 +6,21 @@
 *------------------------------------*/
 
 // Printer revision
-#define PRINTER_TYPE PRINTER_MK25
+#define PRINTER_TYPE PRINTER_MK2
-#define FILAMENT_SIZE "1_75mm_MK25"
+#define FILAMENT_SIZE "1_75mm_MK2"
 #define NOZZLE_TYPE "E3Dv6full"
 
 // Developer flag
 #define DEVELOPER
 
 // Printer name
-#define CUSTOM_MENDEL_NAME "Prusa i3 MK2.5"
+#define CUSTOM_MENDEL_NAME "Prusa i3 MK2"
 
 // Electronics
 #define MOTHERBOARD BOARD_RAMBO_MINI_1_3
 
-#define HEATBED_V2
+// Prusa Single extruder multiple material suport
-#define STEEL_SHEET
+//#define SNMM
-#define TACH0PULLUP
 
 // Uncomment the below for the E3D PT100 temperature sensor (with or without PT100 Amplifier)
 //#define E3D_PT100_EXTRUDER_WITH_AMP
@@ -35,7 +34,12 @@
 *------------------------------------*/
 
 // Steps per unit {X,Y,Z,E}
-#define DEFAULT_AXIS_STEPS_PER_UNIT   {100,100,3200/8,133}
+#ifdef SNMM
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {100,100,3200/8,140}
+#else
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {100,100,3200/8,161.3}
+#endif
+
 
 // Endstop inverting
 const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
@@ -50,16 +54,17 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #define INVERT_E1_DIR true    // for direct drive extruder v9 set to true, for geared extruder set to false
 #define INVERT_E2_DIR true    // for direct drive extruder v9 set to true, for geared extruder set to false
 
+
 // Home position
 #define MANUAL_X_HOME_POS 0
 #define MANUAL_Y_HOME_POS -2.2
-#define MANUAL_Z_HOME_POS 0.2
+#define MANUAL_Z_HOME_POS 0.15
 
 // Travel limits after homing
 #define X_MAX_POS 250
 #define X_MIN_POS 0
 #define Y_MAX_POS 210
-#define Y_MIN_POS -4
+#define Y_MIN_POS -2.2
 #define Z_MAX_POS 210
 #define Z_MIN_POS 0.15
 
@@ -73,55 +78,19 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #define Z_PAUSE_LIFT 20
 
 #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
-#define HOMING_FEEDRATE {3000, 3000, 800, 0}  // set the homing speeds (mm/min) // 3000 is also valid for stallGuard homing. Valid range: 2200 - 3000
+#define HOMING_FEEDRATE {3000, 3000, 800, 0}  // set the homing speeds (mm/min)
 
-#define DEFAULT_MAX_FEEDRATE          {200, 200, 12, 120}      // (mm/sec)   max feedrate (M203)
+#define DEFAULT_MAX_FEEDRATE          {500, 500, 12, 120}    // (mm/sec)
-#define DEFAULT_MAX_ACCELERATION      {1000, 1000, 200, 5000}  // (mm/sec^2) max acceleration (M201)
+#define DEFAULT_MAX_ACCELERATION      {9000,9000,500,10000}    // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
+
+#define DEFAULT_ACCELERATION          1500    // X, Y, Z and E max acceleration in mm/s^2 for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  1500   // X, Y, Z and E max acceleration in mm/s^2 for retracts
 
 
-#define DEFAULT_ACCELERATION          1250   // X, Y, Z and E max acceleration in mm/s^2 for printing moves (M204S)
+#define MANUAL_FEEDRATE {3000, 3000, 1000, 100}   // set the speeds for manual moves (mm/min)
-#define DEFAULT_RETRACT_ACCELERATION  1250   // X, Y, Z and E max acceleration in mm/s^2 for retracts (M204T)
-
-#define MANUAL_FEEDRATE {2700, 2700, 1000, 100}   // set the speeds for manual moves (mm/min)
-
-//number of bytes from end of the file to start check
-#define END_FILE_SECTION 10000
 
 #define Z_AXIS_ALWAYS_ON 1
 
-
-//#define DEBUG_BUILD
-#ifdef DEBUG_BUILD
-//#define _NO_ASM
-#define DEBUG_DCODES //D codes
-#define DEBUG_STACK_MONITOR        //Stack monitor in stepper ISR
-//#define DEBUG_FSENSOR_LOG          //Reports fsensor status to serial
-//#define DEBUG_CRASHDET_COUNTERS  //Display crash-detection counters on LCD
-//#define DEBUG_RESUME_PRINT       //Resume/save print debug enable 
-//#define DEBUG_UVLO_AUTOMATIC_RECOVER // Power panic automatic recovery debug output 
-//#define DEBUG_DISABLE_XMINLIMIT  //x min limit ignored
-//#define DEBUG_DISABLE_XMAXLIMIT  //x max limit ignored
-//#define DEBUG_DISABLE_YMINLIMIT  //y min limit ignored
-//#define DEBUG_DISABLE_YMAXLIMIT  //y max limit ignored
-//#define DEBUG_DISABLE_ZMINLIMIT  //z min limit ignored
-//#define DEBUG_DISABLE_ZMAXLIMIT  //z max limit ignored
-//#define DEBUG_DISABLE_STARTMSGS //no startup messages 
-//#define DEBUG_DISABLE_MINTEMP   //mintemp error ignored
-//#define DEBUG_DISABLE_SWLIMITS  //sw limits ignored
-//#define DEBUG_DISABLE_LCD_STATUS_LINE  //empty four lcd line
-//#define DEBUG_DISABLE_PREVENT_EXTRUDER //cold extrusion and long extrusion allowed
-//#define DEBUG_DISABLE_PRUSA_STATISTICS //disable prusa_statistics() mesages
-//#define DEBUG_XSTEP_DUP_PIN 21   //duplicate x-step output to pin 21 (SCL on P3)
-//#define DEBUG_YSTEP_DUP_PIN 21   //duplicate y-step output to pin 21 (SCL on P3)
-//#define DEBUG_BLINK_ACTIVE
-//#define DEBUG_DISABLE_FANCHECK     //disable fan check (no ISR INT7, check disabled)
-//#define DEBUG_DISABLE_FSENSORCHECK //disable fsensor check (no ISR INT7, check disabled)
-//#define DEBUG_DUMP_TO_2ND_SERIAL   //dump received characters to 2nd serial line
-//#define DEBUG_STEPPER_TIMER_MISSED // Stop on stepper timer overflow, beep and display a message.
-//#define PLANNER_DIAGNOSTICS // Show the planner queue status on printer display.
-#endif /* DEBUG_BUILD */
-
-
 /*------------------------------------
 EXTRUDER SETTINGS
 *------------------------------------*/
@@ -140,7 +109,7 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #endif
 #define HEATER_1_MAXTEMP 305
 #define HEATER_2_MAXTEMP 305
-#define BED_MAXTEMP 125
+#define BED_MAXTEMP 150
 
 #if defined(E3D_PT100_EXTRUDER_WITH_AMP) || defined(E3D_PT100_EXTRUDER_NO_AMP)
 // Define PID constants for extruder with PT100
@@ -149,16 +118,13 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #define  DEFAULT_Kd 73.76
 #else
 // Define PID constants for extruder
-//#define  DEFAULT_Kp 40.925
+#define  DEFAULT_Kp 40.925
-//#define  DEFAULT_Ki 4.875
+#define  DEFAULT_Ki 4.875
-//#define  DEFAULT_Kd 86.085
+#define  DEFAULT_Kd 86.085
-#define  DEFAULT_Kp 16.13
-#define  DEFAULT_Ki 1.1625
-#define  DEFAULT_Kd 56.23
 #endif
 
 // Extrude mintemp
-#define EXTRUDE_MINTEMP 180
+#define EXTRUDE_MINTEMP 130
 
 // Extruder cooling fans
 #define EXTRUDER_0_AUTO_FAN_PIN   8
@@ -168,24 +134,17 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #define EXTRUDER_AUTO_FAN_SPEED   255  // == full speed
 
 
-#define PAT9125 //!< Filament sensor
+#ifdef SNMM
-#define FANCHECK
+//#define BOWDEN_LENGTH	408
-//#define WATCHDOG
+#define BOWDEN_LENGTH 433 //default total length for filament fast loading part; max length for extrusion is 465 mm!; this length can be adjusted in service menu
-#define SAFETYTIMER
+#define FIL_LOAD_LENGTH 102 //length for loading filament into the nozzle
+#define FIL_COOLING 10 //length for cooling moves
+#define E_MOTOR_LOW_CURRENT 350 // current for PRUSAY code
+#define E_MOTOR_HIGH_CURRENT 700 //current for unloading filament, stop print, PRUSAY ramming
+#endif //SNMM
 
+//#define DIS //for measuring bed heigth and PINDa detection heigth relative to auto home point, experimental function
 
-/*------------------------------------
- LOAD/UNLOAD FILAMENT SETTINGS
- *------------------------------------*/
-
-// Load filament commands
-#define LOAD_FILAMENT_0 "M83"
-#define LOAD_FILAMENT_1 "G1 E70 F400"
-#define LOAD_FILAMENT_2 "G1 E40 F100"
-
-// Unload filament commands
-#define UNLOAD_FILAMENT_0 "M83"
-#define UNLOAD_FILAMENT_1 "G1 E-80 F7000"
 
 /*------------------------------------
 CHANGE FILAMENT SETTINGS
@@ -206,8 +165,7 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 
 #define FILAMENTCHANGE_XYFEED 50
 #define FILAMENTCHANGE_EFEED 20
-//#define FILAMENTCHANGE_RFEED 400
+#define FILAMENTCHANGE_RFEED 400
-#define FILAMENTCHANGE_RFEED 7000 / 60
 #define FILAMENTCHANGE_EXFEED 2
 #define FILAMENTCHANGE_ZFEED 15
 
@@ -222,6 +180,7 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 
 #ifdef FILAMENT_RUNOUT_SUPPORT
 #define FILAMENT_RUNOUT_SENSOR 1
+#define FILAMENT_RUNOUT_SCRIPT "M600"
 #endif
 
 // temperature runaway
@@ -248,13 +207,6 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #define Z_HIGH_POWER 200
 #endif
 
-/*------------------------------------
- PAT9125 SETTINGS
- *------------------------------------*/
-
-#define PAT9125_XRES			0
-#define PAT9125_YRES			255
-
 /*------------------------------------
 BED SETTINGS
 *------------------------------------*/
@@ -282,7 +234,7 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #define MESH_HOME_Z_SEARCH 5 //Z lift for homing, mesh bed leveling etc.
 
 #define X_PROBE_OFFSET_FROM_EXTRUDER 23     // Z probe to nozzle X offset: -left  +right
-#define Y_PROBE_OFFSET_FROM_EXTRUDER 5     // Z probe to nozzle Y offset: -front +behind
+#define Y_PROBE_OFFSET_FROM_EXTRUDER 9     // Z probe to nozzle Y offset: -front +behind
 #define Z_PROBE_OFFSET_FROM_EXTRUDER -0.4  // Z probe to nozzle Z offset: -below (always!)
 #endif
 
@@ -345,7 +297,7 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #define FARM_PREHEAT_FAN_SPEED 0
 
 #define PLA_PREHEAT_HOTEND_TEMP 215
-#define PLA_PREHEAT_HPB_TEMP 60
+#define PLA_PREHEAT_HPB_TEMP 55
 #define PLA_PREHEAT_FAN_SPEED 0  
 
 #define ABS_PREHEAT_HOTEND_TEMP 255
@@ -360,11 +312,11 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #define PP_PREHEAT_HPB_TEMP 100
 #define PP_PREHEAT_FAN_SPEED 0 
 
-#define PET_PREHEAT_HOTEND_TEMP 230
+#define PET_PREHEAT_HOTEND_TEMP 240
-#define PET_PREHEAT_HPB_TEMP 85
+#define PET_PREHEAT_HPB_TEMP 90
 #define PET_PREHEAT_FAN_SPEED 0 
 
-#define FLEX_PREHEAT_HOTEND_TEMP 240
+#define FLEX_PREHEAT_HOTEND_TEMP 230
 #define FLEX_PREHEAT_HPB_TEMP 50
 #define FLEX_PREHEAT_FAN_SPEED 0 
 
@@ -425,7 +377,6 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #else
 #define TEMP_SENSOR_BED 1
 #endif
-#define TEMP_SENSOR_PINDA 1
 
 #define STACK_GUARD_TEST_VALUE 0xA2A2
 
@@ -438,13 +389,9 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #define Z_BABYSTEP_MIN -3999
 #define Z_BABYSTEP_MAX 0
 
-#define PINDA_PREHEAT_X 20
-#define PINDA_PREHEAT_Y 60
-#define PINDA_PREHEAT_Z 0.15
-/*
 #define PINDA_PREHEAT_X 70
 #define PINDA_PREHEAT_Y -3
-#define PINDA_PREHEAT_Z 1*/
+#define PINDA_PREHEAT_Z 1
 #define PINDA_HEAT_T 120 //time in s
 
 #define PINDA_MIN_T 50
@@ -455,21 +402,26 @@ const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 #define PING_TIME_LONG 600 //10 min; used when length of commands buffer > 0 to avoid false triggering when dealing with long gcodes
 #define PING_ALLERT_PERIOD 60 //time in s
 
+#define NC_TIME 10 //time in s for periodic important status messages sending which needs reponse from monitoring
+#define NC_BUTTON_LONG_PRESS 15 //time in s
+
 #define LONG_PRESS_TIME 1000 //time in ms for button long press 
 #define BUTTON_BLANKING_TIME 200 //time in ms for blanking after button release
 
 #define DEFAULT_PID_TEMP 210
 
-#define MIN_PRINT_FAN_SPEED 75
-
 #ifdef SNMM
 #define DEFAULT_RETRACTION 4 //used for PINDA temp calibration and pause print
 #else
 #define DEFAULT_RETRACTION 1 //used for PINDA temp calibration and pause print
 #endif
 
+#define END_FILE_SECTION 10000 //number of bytes from end of file used for checking if file is complete
+
 #define M600_TIMEOUT 600  //seconds
 
+#ifndef SNMM
 #define SUPPORT_VERBOSITY
+#endif
 
 #endif //__CONFIGURATION_PRUSA_H

Firmware/ultralcd.cpp

@@ -5624,12 +5624,14 @@ static void lcd_tune_menu()
 #endif
 
 #ifndef DEBUG_DISABLE_FSENSORCHECK
+#ifdef PAT9125
 	if (FSensorStateMenu == 0) {
 		MENU_ITEM(function, MSG_FSENSOR_OFF, lcd_fsensor_state_set);
 	}
 	else {
 		MENU_ITEM(function, MSG_FSENSOR_ON, lcd_fsensor_state_set);
 	}
+#endif //PAT9125
 #endif //DEBUG_DISABLE_FSENSORCHECK
 
 #ifdef TMC2130

Firmware/variants/1_75mm_MK2-RAMBo13a-E3Dv6full.h

@@ -6,6 +6,7 @@ GENERAL SETTINGS
 *------------------------------------*/
 
 // Printer revision
+#define PRINTER_TYPE PRINTER_MK2
 #define FILAMENT_SIZE "1_75mm_MK2"
 #define NOZZLE_TYPE "E3Dv6full"