Robert Pelnar
0685439e36
Cmd queue modification. Added CMDHDRSIZE=2, each command readed from SD is preceded by one byte variable containing original length.
2017-09-12 19:20:41 +02:00
Robert Pelnar
d9cdb1da60
Ambient thermistor - table and conversion function, extruder motor changed back to 200steps type, extruder resolution changed to 32usteps.
2017-09-06 16:04:50 +02:00
Robert Pelnar
8ec316773f
PINDA thermistor and ambient thermistor.
2017-09-05 14:02:35 +02:00
Robert Pelnar
f563618b1c
PINDA thermistor + extruder current adjust.
2017-08-30 21:56:48 +02:00
Robert Pelnar
1e705198e0
LCD backlight brightnes pwm control and lcd blinking.
2017-08-21 17:23:30 +02:00
Robert Pelnar
d63045fdb3
TMC2130 stallguard improovment - axis load monitoring, autocalibrate Z.
2017-08-21 13:06:17 +02:00
Robert Pelnar
683784c4c7
PAT9125 I2C, hardware SG homing
...
separate pin configuration file for each board
changed board codes:
RAMBO =100, MiniRambo1.0 =200, MiniRambo1.3 = 203, Einy03 =303, Einy04 =304
2017-08-17 15:23:34 +02:00
XPila
a41a836ef0
Merge branch 'MK3' into MK3
2017-07-12 17:54:41 +02:00
Robert Pelnar
cd48d5b4ff
TMC2130 stallguard SW homing improvement - steps delta instead of delay (loop count), new function tmc2130_home_restart, always enable endstops durring homing.
2017-07-12 17:36:50 +02:00
michalprusa
281ae26a5e
Merge branch 'MK3' into MK3-michal
2017-07-07 10:43:39 +02:00
michalprusa
e6c7a29693
filament sensor tweaked for 400 step motor.
...
On/OFF switch for filament sensor
2017-07-07 10:42:36 +02:00
XPila
76477edf63
Merge pull request #20 from XPila/MK3
...
SG homing - fixed bug - set sg_homing_delay to zero before move.
2017-07-07 07:47:07 +02:00
Robert Pelnar
21974ae07a
SG homing - fixed bug - set sg_homing_delay to zero before move.
2017-07-07 07:45:36 +02:00
michalprusa
52554d72c4
PAT9125 finally able to turn off
2017-07-07 07:34:35 +02:00
michalprusa
7ffa42f43a
PAT9125 init result print
2017-07-07 05:41:41 +02:00
michalprusa
ea17fa56d7
Merge remote-tracking branch 'origin/MK3-michal' into MK3-michal
...
# Conflicts:
# Firmware/ultralcd.cpp
2017-07-07 05:00:23 +02:00
XPila
82c1fc978b
Merge branch 'MK3' into MK3-michal
2017-07-07 04:51:01 +02:00
michalprusa
e23f34339e
Power panic improved by turning off Z steppers
...
Dubug outputs for filament and fan rotation sensors moved to special menu Support->Extruder info
XYZ calibration debug now available only while not printing
2017-07-07 04:50:00 +02:00
XPila
c1f6646d08
Merge pull request #16 from XPila/MK3
...
pat9125 filament sensor
2017-07-07 04:46:45 +02:00
Robert Pelnar
ec7678a25f
pat9125 filament sensor
...
sg homing - bug fix + homing multiple axes simultanously (AXIS_MASK)
2017-07-07 04:45:09 +02:00
michalprusa
87ff9db76e
Merge remote-tracking branch 'origin/MK3' into MK3-michal
2017-07-07 02:12:18 +02:00
michalprusa
06fe85e9ee
Linear Advance
2017-07-07 01:58:02 +02:00
PavelSindler
2ea8e11eea
power panic: extrusion to stabilize pressure, waiting for temperature in homing position
2017-07-06 23:01:59 +02:00
PavelSindler
e521831245
status message during print recovery
2017-07-06 19:31:18 +02:00
PavelSindler
c9d7b65c02
updated z recovery in power panic, added test to main menu
2017-07-06 19:09:06 +02:00
PavelSindler
21f068b37a
changed Z axis recovery in power panic
2017-07-06 17:09:35 +02:00
PavelSindler
8ceca8b9c6
power panic - fixed z axis recovery
2017-07-06 15:52:38 +02:00
XPila
78f7923ab2
Merge pull request #10 from XPila/MK3
...
Changed jerks, disabled oversampling, debug code, commands for seting…
2017-07-06 13:07:37 +02:00
Robert Pelnar
2b24e9ceb3
Changed jerks, disabled oversampling, debug code, commands for seting pwm_ampl and pwm_grad (M917, M918), changed configuration files
2017-07-06 13:06:07 +02:00
XPila
458dfa80f6
Merge branch 'MK3' into MK3
2017-07-06 12:55:30 +02:00
PavelSindler
16fffed52d
current feedrate and fan speed stored to eeprom in power panic, number of blocks (linear movements) in planner serve for counting SD card recover position, print fan speed error limit prolonged to 15s
2017-07-05 15:04:43 +02:00
PavelSindler
2c102f8580
fixed SD card restore position (power panic)
2017-07-05 09:16:33 +02:00
PavelSindler
ef7a302626
power panic: Z axis is lowered in position where print starts (is recovered)
2017-07-04 20:58:44 +02:00
Andre Sklenar
9e3d608ba0
Merge branch 'MK3' of github.com:prusa3d/Prusa-Firmware-DEV into MK3
2017-07-04 16:25:53 +02:00
Andre Sklenar
5ab57ab2ad
Init LCD ASAP for a nice UX
2017-07-04 16:25:30 +02:00
Robert Pelnar
b8025e63e6
DEBUG defines, variant files for MK3
2017-07-04 16:23:28 +02:00
PavelSindler
a8678cb2fd
recover print
2017-07-04 11:31:39 +02:00
PavelSindler
d05e62813a
Merge remote-tracking branch 'upstream/MK3' into MK3
...
sync with upstream
2017-07-03 14:08:39 +02:00
PavelSindler
4ae5751d95
added debug messages for serial
2017-07-03 14:08:27 +02:00
Robert Pelnar
176c32de91
TMC2130 stallguard homing - sg_thrs_x and sg_thrs_y - command M916, lcd_silent_mode_set_tune
2017-07-03 10:39:56 +02:00
Robert Pelnar
e09f0c64c7
TMC2130 tuning, silent/high power mode
2017-07-03 07:43:50 +02:00
Robert Pelnar
c4307c7373
TMC2130 tunning, overtemp
2017-07-03 00:11:42 +02:00
PavelSindler
17074e1d25
saving/restoring filename and current position in bytes to eeprom, UVLO changed
2017-07-02 21:01:23 +02:00
PavelSindler
db12119b68
position saving and restoring in UVLO
2017-07-02 00:11:21 +02:00
PavelSindler
ae0c64248f
sync with upstream
2017-07-01 19:29:57 +02:00
PavelSindler
c4be651d2b
uvlo initial version
2017-07-01 18:51:02 +02:00
Robert Pelnar
f6a8e1df9d
TMC2130 + software SG homing + LF lineendings + tmc2130 debug M-Codes
...
M910 - tmc2130_init
M911 - set holding currents
M912 - set running currents
M913 - print currents
2017-07-01 12:39:16 +02:00
PavelSindler
43d696659f
3.0.12-RC2 sync
2017-06-29 18:35:43 +02:00
PavelSindler
0578ea527e
fan speed check initial version, selftest updated
2017-06-28 14:24:45 +02:00
michalprusa
6f3c28c4a7
Filament sensor PAT9125 implemented
2017-06-17 20:40:22 +02:00
