3DPrinting/Prusa-Firmware
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
6,219 Commits 3 Branches 78 Tags 40 MiB
new-main
Commit Graph

262 Commits

Author SHA1 Message Date
3d-gussner
12f4102272 Group PINDA defines 2020-12-23 21:00:02 +01:00
3d-gussner
4b510fef0a Add PINDA_TEMP_COMP variable to enable SuperPINDA toggle menu/function 2020-12-23 20:59:08 +01:00
3d-gussner
a97587f373 Changed PINDA_MINTEMP having own value 
Prevent bad readings/issues if someone changes the bed thermistor that is "better" with lower min values and creates a custom firmware.
The firmware will now be in the range of the PINDAv2 thermistor independant from the bed thermistor (which may change and need adjustments)
 2020-12-23 20:58:44 +01:00
3d-gussner
62c36f718b Add SuperPINDA support for MK2.5/S 
- Changed DETECT_SUPERPINDA to SUPERPINDA_SUPPORT as on miniRAMo the thermistor readings below 30°C
  aren't accurate egnough to determine if SUPERPINDA is connected or not
- Add LCD toggle menu Settings -> HW Setup -> SuperPINDA [Yes/No] to overwrite SuperPINDA detection
  - If EEPROM_PINDA_TEMP_COMPENSTATION is empty = 0xff then detect SuperPINDA by checking thermistor
  - If EEPROM_PINDA_TEMP_COMPENSTAION is 0 then forec enable for temperature compensation menues and functions
  - If EEPROM_PINDA_TEMP_COMPENSATION is 1 then force disable for temperature compensation menues and functions
 2020-12-23 20:56:50 +01:00
Yuri D'Elia
a60ed81a35 Implement MIN/MAX AMBIENT safety checks 
Take advantage of the NTC thermistor found on the Einsy as an additional
safety measure, following the steps of the other MIN/MAXTEMP errors.

Introduce two configurable params AMBIENT_MINTEMP and AMBIENT_MAXTEMP
in the variant defines and set them for the MK3/MK3S to -30/+100
respectively.

AMBIENT_MINTEMP is primarily intended to catch a defective board
thermistor (to ensure MAXTEMP would be properly triggered) and thus the
trigger temperature is set just above the sensing limit and well below
the operating range.

AMBIENT_MAXTEMP is set at 100C, which is instead 20C above the maximum
recommended operating temperature of the Einsy. The NTC thermistor is
located just above the main power connector on the bottom of the board,
and could also help in detecting a faulty connection which can result in
rapid overheating of the contacts.

As for MAXTEMP, we cut power to the heaters, print fan and motors to
reduce power draw. Resume is not possible except by resetting the
printer, since the user is highly advised to inspect the board for
problems before attempting to continue.
 2020-08-01 17:38:10 +02:00
Yuri D'Elia
1181beffb1 Enable DEDGE stepping on supported variants 2020-06-24 17:58:43 +02:00
Marek Bel
bdf53387b1 Disable temperature compensation and temperature calibration menu if superPINDA is detected. 
Even though functionality was added, 20B of flash memory has been saved.
 2020-06-16 00:19:06 +02:00
D.R.racer
fe72ba7a9d Add PC-blend preheat preset 2020-06-03 17:45:55 +02:00
Alex Voinea
751f810dd7
ALTFAN implementation (#2692) 
* ALTFAN implementation

* Use CRITICAL_SECTION macros

* Use uint16_t instead of unsigned int

* Add forgotten CRITICAL_SECTION

* Documentation
 2020-06-01 17:58:15 +02:00
DRracer
a10b7f3963
Merge pull request #2470 from leptun/MK3_Adjusted_mintemp 
Adjusted hotend, bed and Ambient mintemp values
 2020-02-07 08:54:50 +01:00
Yuri D'Elia
eb2ca78167 Rewrite uvlo handling for accurate Z re/positioning 
- In both uvlo_ and uvlo_tiny, calculate Z usteps properly and adjust
  the Z position to a true fullstep before disabling the motor. This
  avoids shifs during recovery.
- In uvlo_tiny, instead of moving up indefinitely, adjust Z just
  once using the smallest move possible (new def UVLO_TINY_Z_AXIS_SHIFT)
- Perform all the uvlo/recovery processing in physical coordinates
  and MBL off: there should be no automatic Z movement!
- Disable heaters in both handlers to conserve more power.
- Add timing information to uvlo_tiny too.
- During recovery, to switch between physical and logical positioning
  introduce a new "PRUSA MBL" gcode as most of the procedure is
  enqueued, and no existing gcode was available.
 2020-01-26 17:46:50 +01:00
Alex Voinea
e6ba9e633c
Adjusted hotend, bed and Ambient mintemp values 2020-01-21 14:50:53 +02:00
DRracer
4c74866864
Merge pull request #1933 from prusa3d/enable_cutter 
Enable MMU cutter.
 2020-01-09 13:47:44 +01:00
Yuri D'Elia
19589f02f1 Remove an unused define 2019-12-04 17:22:21 +01:00
Alex Voinea
779423f0e7
Move hardcoded values to variants 2019-11-29 15:06:54 +02:00
DRracer
521c5eb8ef
Merge pull request #2141 from mkbel/preheat_menu 
Unify preheat menu, add ASA material
 2019-09-12 14:25:38 +02:00
Marek Bel
0fda4e5594 Merge branch 'cut_last_try' into enable_cutter 2019-09-10 18:37:09 +02:00
DRracer
898e85e69f
Merge pull request #2038 from Eriobis/MK3 
Add a threshold distance to Z calibration
 2019-09-10 16:20:24 +02:00
MRprusa3d
7cc9fe2e4f
Update 1_75mm_MK3S-EINSy10a-E3Dv6full.h 2019-09-09 02:20:39 +02:00
MRprusa3d
70de4d58f6
Update 1_75mm_MK3-EINSy10a-E3Dv6full.h 2019-09-09 02:20:14 +02:00
MRprusa3d
fb561b15ad
Update 1_75mm_MK25S-RAMBo13a-E3Dv6full.h 2019-09-09 02:19:52 +02:00
MRprusa3d
325e4a3403
Update 1_75mm_MK25S-RAMBo10a-E3Dv6full.h 2019-09-09 02:19:27 +02:00
MRprusa3d
0b50b2295c
Update 1_75mm_MK25-RAMBo13a-E3Dv6full.h 2019-09-09 02:18:54 +02:00
MRprusa3d
e581263bf1
Update 1_75mm_MK25-RAMBo10a-E3Dv6full.h 2019-09-09 02:18:22 +02:00
MRprusa3d
ca6937edaf
Update 1_75mm_MK2-RAMBo13a-E3Dv6full.h 2019-09-09 02:17:42 +02:00
MRprusa3d
a9a3d9d084
Update 1_75mm_MK2-RAMBo10a-E3Dv6full.h 2019-09-09 02:17:00 +02:00
Marek Bel
3da43ae8c2 Do not port print fan preheat speed preset, as it was never used. And it was broken until recently fixed when adding ASA profile. 2019-08-26 21:14:07 +02:00
Marek Bel
eb68bb9b43 Add ASA preheat. 2019-08-15 17:46:29 +02:00
Marek Bel
469ca6e184 Merge commit 'refs/tags/v3.8.0-RC1^{}' into enable_cutter 2019-08-15 14:48:28 +02:00
Simon Benoit
49d2866b48 Add threshold distance to Z calibration 
Add missing if statement
 2019-07-30 19:43:07 -04:00
Marek Bel
f9e32c4bf4 Re-enable linearity correction for MK3. 2019-07-23 19:22:54 +02:00
DRracer
8b806f692e
Merge pull request #1664 from MRprusa3d/PFW-811 
"disable_z()" for Delta PSU
 2019-07-16 16:46:34 +02:00
Marek Bel
4e7de776cd Disable TMC2130 linarity correction for MK3 to save FLASH to enable compilation. Add symlink /Firmware/variants/printers.h to .gitignore. 2019-07-10 17:07:00 +02:00
MRprusa3d
8229a45187 pre-production version ;-) 2019-07-09 12:16:51 +02:00
MRprusa3d
4db4f19128 'variant files' update ;-((( 2019-07-03 18:14:48 +02:00
MRprusa3d
7e3cb98a1f & MK3S 2019-07-03 17:50:41 +02:00
MRprusa3d
a3a7f3106e print parameters checking 2019-07-03 17:21:11 +02:00
Marek Bel
181c42fa62 Merge remote-tracking branch 'prusa3d/MK3' into enable_cutter 2019-06-18 20:03:41 +02:00
MRprusa3d
b7d3766ae2
Merge branch 'MK3' into PFW-790 2019-06-12 17:32:13 +02:00
Marek Bel
00da4640e2 Document. 2019-05-30 23:29:33 +02:00
Marek Běl
efa8e6e6ba
Merge pull request #1658 from Harpalyke/save-ustep-res-with-M500 
Allow save of uStep resolution with M500
 2019-05-13 17:08:34 +02:00
Marek Bel
a9d6ae296b Enable watchdog for all variants. 2019-05-10 16:30:08 +02:00
Robert Pelnar
18dec75b56 MK2.5 - watchdog enabled + test (command "D-1") 2019-04-29 13:19:59 +02:00
Marek Bel
469aa10097 Enable MMU cutter. 2019-03-29 07:27:29 +01:00
MRprusa3d
632781c4a2 "disable_z()" for Delta PSU 2019-03-21 00:45:15 +01:00
Harpalyke
0f21ccee3c Adding the microstepping resolution for all axis to the eprom config which is persisted during M500 for Mk3 and Mk3S 2019-03-19 21:39:59 +00:00
MRprusa3d
7d98177716 farmMode updates 2019-03-19 19:48:40 +01:00
PavelSindler
c05561d6b1
Merge pull request #1607 from PavelSindler/7x7 
7x7 mbl and switching mmu modes
 2019-03-15 19:55:15 +01:00
PavelSindler
0ca52216f3 Revert "variants update" 
This reverts commit c3a95ab79b.
 2019-03-15 13:14:32 +01:00
Marek Bel
ffe45bdef3 Disable mmu filament cutter feature. 2019-03-15 03:38:37 +01:00
PavelSindler
9e0e4198c5 Mesh by 3d-gussner, fixed difference between mbl points coordinates and coordinates used in planner for corrections, mbl settings menu update 2019-03-14 01:52:44 +01:00
PavelSindler
c3a95ab79b variants update 2019-03-12 11:57:35 +01:00
PavelSindler
f0cc313fed debug gcodes (fans, bed analysis) moved to Dcodes, HOST_KEEPALIVE_FEATURE simplified 2019-03-06 19:56:48 +01:00
PavelSindler
7f92d73a40 MMU_STEALTH_MODE -> MMU_FORCE_STEALTH_MODE; activate_stealth_mode() function update 2019-03-04 17:04:22 +01:00
PavelSindler
26cab2911f mmu stealth mode 2019-02-22 16:30:54 +01:00
PavelSindler
a220c97f94 Revert "variant files" 
This reverts commit 850d3316b6.
 2019-02-06 16:19:30 +01:00
PavelSindler
850d3316b6 variant files 2019-02-06 15:18:12 +01:00
PavelSindler
5324181bf7 maximum bed level correction value enlarged from 50um to 100um and is now used in menus and mesh bed leveling itself 2019-02-03 20:56:14 +01:00
PavelSindler
60acdd23c5 variants 2019-01-28 21:12:38 +01:00
PavelSindler
8f039263d5 variant files and version 2019-01-28 17:14:24 +01:00
PavelSindler
7e3a1c7d45 merge changes from upstream 2019-01-25 17:57:24 +01:00
MRprusa3d
46e2bdaf62 Merge remote-tracking branch 'public_remote/MK3' into PFW-556 2019-01-24 19:39:34 +01:00
PavelSindler
e0c1e4a02d version which should on all printer versions: autoload, selftest, filament detection, filament sensors initialization, filament menus 2019-01-24 01:12:30 +01:00
MRprusa3d
867182c266 minTemp 
more user-proof solution
 2019-01-23 18:50:13 +01:00
PavelSindler
54f8f4eb4d
Merge pull request #1460 from MRprusa3d/PFW-723 
Pfw 723
 2019-01-23 14:12:19 +01:00
MRprusa3d
d7ac459da7 PID / manage_heater 
build-warnings elimination
 2019-01-20 01:23:15 +01:00
Marek Bel
052ae323f8 Merge branch 'MK3' into prusa3d-DEV_MK3 2019-01-15 16:58:36 +01:00
PavelSindler
3ab1daf722 MMU_DEBUG temporarily enabled 2018-12-21 23:17:32 +01:00
PavelSindler
688d4a8a82 missing defines in variant files 2018-12-21 21:05:54 +01:00
PavelSindler
3c64bad1cb initial version which works on old and new hw, initial version of idler sensor detection 2018-12-21 17:12:16 +01:00
PavelSindler
29ecd4ec7a duplicit T-codes execution improved, E-stepper movements when waiting for ok from mmu, continue loading function improved, eeprom: fail stats for mmu 2018-12-12 22:32:47 +01:00
PavelSindler
e52e53d1eb send continue loading commands periodically if initial load fails 2018-12-12 13:54:17 +01:00
Robert Pelnar
35378769fd MMU - idler sensor 2018-12-06 19:19:50 +01:00
Robert Pelnar
6157c3ab32 New filament sensor 2018-12-06 15:41:53 +01:00
MRprusa3d
83a9f75abe minTemp 
correct minTemp detection @ MK2.5 & MK3
 2018-11-28 23:43:16 +01:00
PavelSindler
32da5bc039 progress bar time counted from feedrate and E - distance 2018-11-12 19:55:53 +01:00
Robert Pelnar
9a68501039 MK2 variants compilable 2018-11-06 14:17:43 +01:00
PavelSindler
908fffc19a
Merge pull request #1306 from PavelSindler/fsensor_q 
filament quality measurements disabled
 2018-11-05 19:14:34 +01:00
PavelSindler
89ad02ac8c filament quality measurements disabled 2018-11-05 18:37:36 +01:00
Robert Pelnar
d6b5f5a1c7 PFW643 - removed M910-M918, implemented M907 2018-11-05 16:15:27 +01:00
PavelSindler
96ce324b7c load to nozzle improved, unified feedrate and E-distance for final feed used in load filament function, M600 etc. 2018-11-01 16:29:09 +01:00
PavelSindler
d005005e22 Merge remote-tracking branch 'upstream/3_4_2' into 3_4_2_branch_merging 2018-10-22 20:33:38 +02:00
PavelSindler
bc247ca02c MK2.5 sw reset at setup function 2018-10-19 17:54:48 +02:00
PavelSindler
b8f92fdfa9 MK2.5 printers set mmu to stealth mode (using Mx code), required mmu2 buildnr can be different for MK2.5 and MK3 printers 2018-10-18 02:44:16 +02:00
mkbel
0d9b502937
Merge pull request #1246 from PavelSindler/variants_max 
MK3: default max feedrate for x and y changed to 100mm/s
 2018-10-10 16:46:34 +02:00
PavelSindler
bbd4f70f41
Merge pull request #1221 from XPila/MK3 
Update fsensor in Manage_inactivity instead of main loop.
 2018-10-10 13:12:12 +02:00
PavelSindler
809ae5a5f0 default max feedrate for x and y changed to 100mm/s 2018-10-09 20:03:28 +02:00
Robert Pelnar
9960c80bf7 Additional check always with enabled oq_meassure 
+ variant files
 2018-10-04 16:12:41 +02:00
MRprusa3d
0184f06dcf preHeatError 
correction of preHeatError detection
 2018-09-27 04:23:00 +02:00
PavelSindler
1bb9e9ed92 MMU_DEBUG 2018-09-10 20:39:28 +02:00
PavelSindler
d96b0d5f32 linearity correction define added (menu readded) 2018-08-30 11:28:12 +02:00
PavelSindler
5769b758ee max feedrate for stealth mode reduced to 100mm/s (because of loudness) 2018-08-26 16:50:28 +02:00
Robert Pelnar
71f1a1f6db MMU - communication, check after start, code cleaning 2018-08-07 20:37:59 +02:00
Robert Pelnar
d378575a68 SNMM_V2 - default retraction declared as variable 2018-08-02 17:07:09 +02:00
PavelSindler
40da6deef8 timeouts used when getting response from mmu, M600 improvements, no filament sensor in variants file 2018-07-31 19:00:42 +02:00
PavelSindler
4fb27866f4
Merge pull request #972 from PavelSindler/end_file_section 
End file section for searching M84 in gcode file enlarged
 2018-07-26 19:59:37 +02:00
PavelSindler
5bc40aff85
Merge pull request #975 from XPila/MK3-new_lang 
EEPROM dump (code D3)
 2018-07-26 19:59:09 +02:00
PavelSindler
5bda19b9f7 config for mmu updated 2018-07-26 14:59:49 +02:00
Robert Pelnar
691e7a24ed EEPROM dump (code D3) 2018-07-26 13:20:35 +02:00
PavelSindler
da82062d41 End file section for searching M84 in gcode file were enlarged (compatibility with mmu Slic3r) 2018-07-25 18:26:22 +02:00