bubnikv
26747d7236
Definition of 8 pins on the Einsy 0.4 board connected to pin headers
...
to be monitored by an 8 channel logic analyzer, for example the Saleae.
2018-01-12 20:18:20 +01:00
bubnikv
db985065ff
WRITE_NC macro for non-critical (non-synchronized) access to
...
slow ports. The WRITE macro stores the CPU bits on the stack first,
then locks the interupts, reads the port, sets a bit, writes the port
and then finally reverts the CPU bits. The WRITE_NC does not lock
the interrupts, therefore it may only be used where it cannot
be interrupted.
2018-01-12 20:15:59 +01:00
PavelSindler
1fbed53200
initial
2018-01-12 20:01:22 +01:00
Robert Pelnar
0f46fa0c37
blocking messages in settings/tune menu (PFW104)
...
switch normal/stealth (PFW110)
2018-01-12 19:54:32 +01:00
PavelSindler
a4be2af538
commit nr updated
2018-01-11 17:51:30 +01:00
PavelSindler
f5ed12817d
Merge pull request #388 from PavelSindler/first_layer_saving
...
Live adjust Z saving using timeout
2018-01-11 17:49:40 +01:00
PavelSindler
5c1db284b0
remove setting live adjust status in setup function
2018-01-11 17:48:58 +01:00
PavelSindler
97bd56d560
Merge pull request #386 from PavelSindler/selftest_swapped_fans
...
manual check for swapped fans
2018-01-11 17:45:23 +01:00
bubnikv
cfae8f859d
Merge branch 'MK3' into fw_versions
2018-01-11 16:58:47 +01:00
PavelSindler
087532085f
development fw versions has initial message for warning
2018-01-11 15:50:26 +01:00
PavelSindler
cc20da62a8
whitespace
2018-01-10 23:31:06 +01:00
PavelSindler
c185b46eb2
live adjust Z saving using timeout
2018-01-10 23:28:41 +01:00
Robert Pelnar
0d269261e4
PFW-110 - load filament - beep when loading finished.
2018-01-10 18:50:16 +01:00
PavelSindler
c79d960cb5
manual check for swapped fans
2018-01-10 16:40:06 +01:00
XPila
6ff7641d97
Merge pull request #385 from XPila/MK3
...
Build 143f
2018-01-09 20:01:56 +01:00
Robert Pelnar
43010b30b4
Build 143f
...
Crashdetection improoved, blocking temperature ISR fixed, limits for silent mode adjusted.
2018-01-09 19:54:07 +01:00
PavelSindler
858945d949
thermal runaway: reset cmd queue to ensure that heater/bed temp will be always set to zero
2018-01-09 13:35:12 +01:00
PavelSindler
75efc71527
temp runaway for heatbed enabled in config
2018-01-08 16:15:50 +01:00
PavelSindler
b53197fdd1
Fixed error messages for print fan and extruder fan (were swapped)
2018-01-08 12:07:45 +01:00
Robert Pelnar
0a2087c1cb
build 143e
...
Linear advance disabled
Max feedrate reduced to 200mm/s
Silent max accel reduced to 984mm/s^2
some debug logs removed, tmc_init - log message fixed
2018-01-04 18:08:22 +01:00
Robert Pelnar
8a5ba89a9c
Missing serial characters debuging
...
disabled fan ISR
disabled fsensor ISR
disabled linear advance
build 143b
2018-01-02 20:55:33 +01:00
Robert Pelnar
c6e77f55f6
checkrx in stepper returned back
...
build 143a
2017-12-30 02:55:22 +01:00
Robert Pelnar
568f03c46e
build 143
2017-12-29 23:49:11 +01:00
Michal Průša
8d1f2afbf2
build number change
...
just 141r -> 142
2017-12-29 20:22:45 +01:00
Michal Průša
0920b62d80
build number change
2017-12-29 20:21:06 +01:00
Michal Průša
734639c1da
Unload filament tweak
...
unload filament now has longer and faster slow retract.
2017-12-29 17:53:12 +01:00
Phil Dubach
7fb1234855
Turn off bed heater after temp calibration
...
After finishing the temperature calibration, turn off the bed heater
right away, before waiting for the user to acknowledge completion.
2017-12-28 23:47:27 -08:00
Robert Pelnar
e3c006dbe9
Serial communication uses port0 or port1, not both, removed some suspected code.
...
build 141
2017-12-29 00:06:47 +01:00
Michal Průša
f71f133e80
power panic polished
...
Retraction set correctly to have minimum missing line
Z motor current not lowered that drascialy
Extruder motor turning off instantly
Beeping added to the end
2017-12-28 23:26:06 +01:00
Michal Průša
f1c741d027
Filament autoloading improved and minor tweaks
...
Filament autoloading now acts like normal loading (Error message pops out if nozzle too cold, Printer asks if should extrude more when done loading)
Autoloading now unable to turn on when filament sensor is turned off or not responding
Color not right changed to color not correct to avoid slight confusion
2017-12-28 18:59:57 +01:00
Michal Průša
26255766f6
Translation fix
...
on -> zap
off -> vyp
2017-12-28 15:55:16 +01:00
Michal Průša
5e5588c72c
Text grooming
...
Added language mutations of error messages, menu items.
Synced wording of crash detection in messages.
rPi port -> RPi port.
Minor menu items alignment.
2017-12-28 15:45:52 +01:00
Robert Pelnar
bd58718d9d
dummy "ok" response
...
build 139 (RC4)
2017-12-28 02:45:05 +01:00
Robert Pelnar
e064133a04
Merge remote-tracking branch 'upstream/MK3' into MK3
...
# Please enter a commit message to explain why this merge is necessary,
# especially if it merges an updated upstream into a topic branch.
#
# Lines starting with '#' will be ignored, and an empty message aborts
# the commit.
2017-12-28 01:37:13 +01:00
Robert Pelnar
69d496e157
autoload filament menu (PFW-95, PFW-96)
2017-12-27 21:57:51 +01:00
Robert Pelnar
cbd7f033e8
crashdetection and mode menu (PFW-85, PFW-97)
2017-12-27 21:43:04 +01:00
Robert Pelnar
546314fda7
Removed debug messages from serial comunication (octoprint...).
...
build 137b
2017-12-27 20:29:24 +01:00
Robert Pelnar
f9d5619682
MINTEMP safety for ambient temperature < 18C
...
Silent mode acceleration limit lowered to 1000mm/s^2
2017-12-27 18:20:04 +01:00
Robert Pelnar
a09dee7aea
build 138 (RC3)
2017-12-23 03:44:47 +01:00
Robert Pelnar
23ed33fc21
disable crashdetection while usb printing
2017-12-23 03:42:19 +01:00
Robert Pelnar
8739b4a610
MINTEMP fix
2017-12-23 03:36:08 +01:00
Robert Pelnar
1a69c979bf
Increase Z current (PFW-90).
2017-12-23 01:01:57 +01:00
PavelSindler
8f7a50cfcd
Merge pull request #343 from PavelSindler/m110_fix
...
M110 fix
2017-12-23 00:04:11 +01:00
PavelSindler
e8477b525c
initial version of M110 fix (port from MK2)
2017-12-22 22:34:57 +01:00
XPila
257b8e9f59
Merge pull request #342 from XPila/MK3
...
Mk3 - RC3
2017-12-22 20:35:15 +01:00
Robert Pelnar
c4b045083c
Extrude mintemp increased to 190C
2017-12-22 20:34:24 +01:00
Robert Pelnar
7f05b9fd44
changed menu order (PFW 91)
2017-12-22 20:31:45 +01:00
Robert Pelnar
6abba7bfe9
filament autoload - better detection algorithm, autoload in M600 from menu
...
unload menu always visible
2017-12-22 20:14:26 +01:00
PavelSindler
7114772784
whitespace
2017-12-22 19:23:11 +01:00
PavelSindler
3aca1271ed
serial resend request always contains OK
2017-12-22 18:54:55 +01:00
PavelSindler
6f7a2ba263
Merge pull request #340 from PavelSindler/MK3_for_merging
...
removed some serial line error messages
2017-12-22 13:35:33 +01:00
PavelSindler
1917b6a1d7
removed some serial line error messages which caused that octoprint changed status
2017-12-22 13:27:04 +01:00
PavelSindler
33d715616f
Merge pull request #339 from PavelSindler/MK3_for_merging
...
setup function
2017-12-21 13:42:22 +01:00
PavelSindler
71bb4022dc
setup function
2017-12-21 13:40:16 +01:00
Robert Pelnar
3ddbac6056
LCD_PWM removed (will be solved other way)
2017-12-21 01:00:49 +01:00
PavelSindler
f227952c0b
Merge branch 'MK3' into MK3
2017-12-21 00:07:01 +01:00
PavelSindler
b8fd058749
selftest fix
2017-12-21 00:03:41 +01:00
PavelSindler
17d9bb205a
selftest tests filament sensor, selftest messages have language variants
2017-12-20 23:40:18 +01:00
Robert Pelnar
eba2924fdd
Remove load/unload menu when autoload enabled
2017-12-20 22:55:11 +01:00
Robert Pelnar
a3a0e70eeb
Fsensor autoload enabled menu and eeprom variable
2017-12-20 22:29:41 +01:00
Robert Pelnar
c88938e813
Fixed blocked lcd buttons
...
build = 137y
2017-12-20 21:33:07 +01:00
Robert Pelnar
25dd6dd673
new module adc (analog2digital)
...
temperature.cpp - adc sampling state machine removed
new dcode D9 (adc read/write + simulator)
temporarily DEBUG_DISABLE_STARTMSGS because UI blocked
SILENT_MAX_FEEDRATE reduced to 172mm/s
hexfile removed
build number 137x
2017-12-20 13:42:20 +01:00
PavelSindler
a9d5af4a07
Wizard: dont ask if color is clear and dont use automatic filament load; multiscreen messages update
2017-12-20 13:33:45 +01:00
PavelSindler
525d022841
whitespace
2017-12-18 19:17:39 +01:00
PavelSindler
31add2e69f
removed 4 bytes from maiden eeprom check as these could be set earlier to 0 by lcd_status_screen function
2017-12-18 19:15:36 +01:00
XPila
9639b58f4d
Merge pull request #329 from XPila/MK3
...
Meassuring voltages (pwr, bed), voltages menu
2017-12-15 18:42:59 +01:00
Robert Pelnar
01654e7145
Meassuring voltages (pwr, bed), voltages menu
2017-12-15 18:33:35 +01:00
PavelSindler
ecbb5cf54b
selftest fix
2017-12-15 17:54:52 +01:00
XPila
dd1eddb1cb
Merge pull request #327 from XPila/MK3
...
Removed SG software homming
2017-12-15 14:13:00 +01:00
Robert Pelnar
c6e10fb903
Removed SG software homming
...
After Calibration Z enabled minstop (SG and PINDA)
TMC2130 code simplification
2017-12-15 14:10:20 +01:00
PavelSindler
3c95bea693
threshold changed
2017-12-15 14:07:12 +01:00
PavelSindler
5daf53f35b
version changed
2017-12-15 11:55:37 +01:00
PavelSindler
893f34fd85
watchdog reset
2017-12-14 20:28:07 +01:00
PavelSindler
011ebb3675
selftest is checking if fans are swapped, host keepalive messages added
2017-12-14 19:36:32 +01:00
Robert Pelnar
7304579ca5
build 135
2017-12-13 23:19:51 +01:00
Robert Pelnar
ca55cf74e2
Merge remote-tracking branch 'upstream/MK3' into MK3
...
# Please enter a commit message to explain why this merge is necessary,
# especially if it merges an updated upstream into a topic branch.
#
# Lines starting with '#' will be ignored, and an empty message aborts
# the commit.
2017-12-13 22:58:34 +01:00
Robert Pelnar
66e279b41c
Autoload filament - fsensor error couter reset when switched.
2017-12-13 18:12:05 +01:00
Robert Pelnar
356bc403b1
Automatic filament load when printer idle and preheated
2017-12-13 17:39:32 +01:00
Robert Pelnar
cdeb835b5d
Failstat couters initialization
...
build number = 131
2017-12-12 23:37:31 +01:00
XPila
bbd8dc3191
Merge pull request #315 from XPila/MK3
...
new ambient thermistor table
2017-12-12 22:51:02 +01:00
Robert Pelnar
7e00248060
new ambient thermistor table
...
MINTEMP_MINAMBIENT
2017-12-12 22:49:47 +01:00
PavelSindler
00a029ac7f
bed maxtemp = 125
2017-12-12 21:28:14 +01:00
PavelSindler
fde0efc75c
power panic for absolute E coordinates: initial version
2017-12-12 21:20:59 +01:00
PavelSindler
c1416cbb33
Merge pull request #312 from PavelSindler/wizard
...
Wizard: force high power mode during xyz cal. and selftest; wizard for assembled printer
2017-12-12 20:24:15 +01:00
PavelSindler
82dffb688a
force high power mode during xyz cal. and selftest
2017-12-12 20:21:09 +01:00
PavelSindler
997c8de161
shipping prep. reset sets wizard flag, shipping prep wizard improvements
2017-12-12 19:17:37 +01:00
PavelSindler
5b314d0829
second serial active address in eeprom redefined
2017-12-12 17:18:06 +01:00
PavelSindler
f8e3c76315
merging new changes from upstream/MK3
2017-12-12 17:14:48 +01:00
XPila
86418eed2d
Merge pull request #311 from XPila/MK3
...
Ambient thermistor - new table (PFW-71)
2017-12-12 15:46:16 +01:00
Robert Pelnar
0271da3c67
Ambient thermistor - new table (PFW-71)
...
Crashdetection disable durring print (PI3M3-42)
Stealth mode - better limit values (PI3M3-5)
2017-12-12 15:44:42 +01:00
PavelSindler
1ef5543a2a
dont sort files when print is finished
2017-12-12 15:26:48 +01:00
PavelSindler
a724c2664c
menus updated, set lcd_commands_step = 0;
2017-12-12 14:25:13 +01:00
PavelSindler
9ef5570fa3
menus accessable during first layer calibration updated
2017-12-12 13:41:31 +01:00
PavelSindler
d29a95bd65
if first layer calibration is active set SD_PRINTING to true
2017-12-12 11:41:54 +01:00
Robert Pelnar
7204e91ec6
Filament sensor not responding - (PFW-41)
...
build number = 130
2017-12-11 18:17:25 +01:00
Robert Pelnar
124a3e6da8
Stealth mode limits + END_FILE_SECTION=10000
2017-12-11 16:17:36 +01:00
PavelSindler
20de899d25
Merge branch 'MK3' into sort_files
2017-12-11 11:50:47 +01:00
PavelSindler
c9f95628d0
changed version
2017-12-11 11:49:40 +01:00
PavelSindler
13a17f9fd4
dont sort files when changing sort type in settings menu
2017-12-11 11:45:20 +01:00
PavelSindler
1c61f2f29c
First working version
2017-12-11 11:30:49 +01:00
Robert Pelnar
c708f63803
build 128
2017-12-11 00:01:47 +01:00
Robert Pelnar
b76758b7b6
Ram status - heap and stack monitor.
2017-12-10 23:45:46 +01:00
Robert Pelnar
e8b2043d03
Stack monitor in stepper ISR
2017-12-10 20:38:09 +01:00
PavelSindler
26135ea227
all sd sort files: initial version; sorting type switch not added to SD card menu itself
2017-12-10 11:08:50 +01:00
Robert Pelnar
9dba7dcd1f
DISABLE_M42_M226 = +56 bytes RAM (because of stack overflow)
...
build 127
2017-12-09 19:31:27 +01:00
Robert Pelnar
995801c967
Silent mode limits
...
+ cannot compile "END_FILE_SECTION"
2017-12-09 14:41:50 +01:00
Robert Pelnar
82f5a79527
bug fix (cannot compile) - ultralcd.cpp - conversion from (const char*)
2017-12-08 19:22:02 +01:00
PavelSindler
00945cf7c3
version changed
2017-12-08 16:59:45 +01:00
PavelSindler
868aacc7d5
turn on second serial line from settings menu
2017-12-08 16:56:06 +01:00
PavelSindler
07aa7a3803
support two serial lines at the same time
2017-12-07 19:14:17 +01:00
PavelSindler
d0b6b19373
save filename to eeprom first, then check if file is complete
2017-12-07 17:16:23 +01:00
PavelSindler
b5ad41b8af
build number
2017-12-06 18:28:08 +01:00
PavelSindler
2cbd1f7894
fix: added saving filename to eeprom which was removed by accident
2017-12-06 18:13:54 +01:00
PavelSindler
071873b38a
init; last merged file: Marlin_main.cpp
2017-12-06 17:48:16 +01:00
PavelSindler
40b7a5c82f
build number changed
2017-12-06 14:59:26 +01:00
PavelSindler
44218a1b53
incomplete file check ported from MK2: initial version
2017-12-06 14:55:53 +01:00
XPila
443dc53145
Merge pull request #292 from XPila/MK3
...
Automatic filament load in M600
2017-12-05 18:38:23 +01:00
Robert Pelnar
58f8fdb51b
Automatic filament load in M600
2017-12-05 18:37:03 +01:00
PavelSindler
bc0278c6e1
build number changed
2017-12-05 17:13:07 +01:00
PavelSindler
d7db407f32
xyz cal.: add delay_keep_alive messages to reset watchdog (LS optimization method takes more than 4s in some cases)
2017-12-05 13:16:59 +01:00
PavelSindler
22065e4877
merging from dev/MK3
2017-12-02 21:56:39 +01:00
Robert Pelnar
0de584c213
bugfix UVLO - extruder position from stepper
2017-11-29 02:08:15 +01:00
Robert Pelnar
a56b0ccaf8
bugfix - Filament sensor enable from menu
2017-11-29 00:15:45 +01:00
Robert Pelnar
9413eca52c
UVLO recover E absolute mode
...
build number 119
2017-11-28 23:41:58 +01:00
Robert Pelnar
13f1684a4c
build 118
2017-11-28 22:53:51 +01:00
XPila
1da1eaea01
Merge pull request #117 from PavelSindler/m600
...
M600: wait for user before unloading filament
2017-11-28 22:45:57 +01:00
Robert Pelnar
1863819e39
pat9125 reinit when fsensor enabled from menu.
2017-11-28 22:44:58 +01:00
PavelSindler
020a7ec257
unload filament can be repeated
2017-11-28 19:04:43 +01:00
PavelSindler
059c255a35
changed build version to b117
2017-11-28 18:31:38 +01:00
PavelSindler
c0112f05e1
M600: wait for user before unloading filament
2017-11-28 18:28:53 +01:00
PavelSindler
2cf7f54e5f
changed build
2017-11-27 20:29:47 +01:00
PavelSindler
3f7be78997
translation to Czech language added
2017-11-27 18:54:44 +01:00
PavelSindler
bd748bc986
EINY -> EINSY
2017-11-27 18:47:48 +01:00
PavelSindler
211725c946
dont show temp cal message, dont save uvlo flag to eeprom if printing from USB
2017-11-27 18:30:16 +01:00
PavelSindler
ddc8587bbd
Merge pull request #112 from PavelSindler/menu_corrections
...
Menu corrections, translation to Czech language
2017-11-27 18:00:31 +01:00
PavelSindler
ce3f14e1c0
tune menu updated
2017-11-27 17:55:32 +01:00
PavelSindler
67a2e0a706
settings menu updated
2017-11-27 17:01:01 +01:00
PavelSindler
f075711e64
corrected menus
2017-11-27 16:37:46 +01:00
PavelSindler
7c6d63ffb5
pla preheat temp. changed, temp calibration on/off moved to settings menu
2017-11-27 16:21:54 +01:00
PavelSindler
044ed951cb
translations to czech language and menu corrections: initial version
2017-11-27 16:06:34 +01:00
Robert Pelnar
7c8de94778
filament unload - initial
...
lower currents for power panic
2017-11-27 15:54:36 +01:00
Robert Pelnar
533418d63e
opravene nezadouci resetovani watchdogem
...
powerpanic Z shift = 0.64mm (misto 1.92mm)
teplotni kompenzace default = ON
2017-11-27 14:43:56 +01:00
Robert Pelnar
25c16cc835
Extrudser info, merge upstream (powerpanic fix)
...
build number = 114
2017-11-27 07:44:12 +01:00
XPila
60930beb52
Merge pull request #108 from PavelSindler/power_panic
...
Power panic works with folders
2017-11-27 07:27:17 +01:00
Robert Pelnar
1113124bde
PINDA calibration and precalibrated characteristics.
2017-11-27 07:09:53 +01:00
PavelSindler
d9f44eb16b
unused code commented
2017-11-27 06:36:41 +01:00
PavelSindler
bd59e11660
removed serial print
2017-11-27 06:22:32 +01:00
PavelSindler
42b533b5d8
first working version
2017-11-27 06:20:51 +01:00
XPila
3b892e16d8
Merge branch 'MK3' into MK3
2017-11-27 04:49:23 +01:00
Robert Pelnar
4dae6f871e
Sg load meassurement durring self test - 'Belt status'
2017-11-27 04:46:58 +01:00
