Prusa-Firmware/lang/po/Firmware_cs.po

# Translation of Prusa-Firmware into Czech.
#
msgid ""
msgstr ""
"MIME-Version: 1.0\n"
"Content-Type: text/plain; charset=UTF-8\n"
"Content-Transfer-Encoding: 8bit\n"
"Language: cs\n"
"Project-Id-Version: Prusa-Firmware\n"
"POT-Creation-Date: Wed 23 Feb 2022 01:52:15 PM CET\n"
"PO-Revision-Date: Wed 23 Feb 2022 01:52:15 PM CET\n"
"Language-Team: \n"
"X-Generator: Poedit 2.0.7\n"
"X-Poedit-SourceCharset: UTF-8\n"
"Last-Translator: \n"
"Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n"

# MSG_IR_03_OR_OLDER c=18
#: messages.c:166
msgid " 0.3 or older"
msgstr " 0.3 nebo starsi"

# MSG_FS_V_03_OR_OLDER c=18
#: Marlin_main.cpp:9887
msgid "FS v0.3 or older"
msgstr "FS 0.3 nebo starsi"

# MSG_IR_04_OR_NEWER c=18
#: messages.c:165
msgid " 0.4 or newer"
msgstr " 0.4 nebo novejsi"

# MSG_FS_V_04_OR_NEWER c=18
#: Marlin_main.cpp:9886
msgid "FS v0.4 or newer"
msgstr "FS 0.4 a novejsi"

# MSG_IR_UNKNOWN c=18
#: messages.c:167
msgid "unknown state"
msgstr "neznamy stav"

# MSG_MEASURED_OFFSET c=20
#: ultralcd.cpp:2903
msgid "[0;0] point offset"
msgstr "[0;0] odsazeni bodu"

# MSG_CRASH_DET_ONLY_IN_NORMAL c=20 r=4
#: 
msgid "Crash detection can\x0abe turned on only in\x0aNormal mode"
msgstr "Crash detekce muze\x0abyt zapnuta pouze v\x0aNormal modu"

# MSG_CRASH_DET_STEALTH_FORCE_OFF c=20 r=4
#: 
msgid "WARNING:\x0aCrash detection\x0adisabled in\x0aStealth mode"
msgstr "POZOR:\x0aCrash detekce\x0adeaktivovana ve\x0aStealth modu"

# MSG_BABYSTEPPING_Z c=15
#: ultralcd.cpp:3024
msgid "Adjusting Z:"
msgstr "Doladeni Z:"

# MSG_SELFTEST_CHECK_ALLCORRECT c=20
#: ultralcd.cpp:8393
msgid "All correct"
msgstr "Vse OK"

# MSG_WIZARD_DONE c=20 r=3
#: messages.c:120
msgid "All is done. Happy printing!"
msgstr "Vse je hotovo. Tisku zdar!"

# MSG_AMBIENT c=14
#: ultralcd.cpp:1717
msgid "Ambient"
msgstr "Okoli"

# MSG_AUTO c=6
#: messages.c:162
msgid "Auto"
msgstr ""

# MSG_PRESS c=20 r=2
#: ultralcd.cpp:2475
msgid "and press the knob"
msgstr "a stisknete tlacitko"

# MSG_CONFIRM_CARRIAGE_AT_THE_TOP c=20 r=2
#: ultralcd.cpp:3345
msgid "Are left and right Z~carriages all up?"
msgstr "Dojely oba Z voziky k~hornimu dorazu?"

# MSG_AUTO_HOME c=18
#: messages.c:11
msgid "Auto home"
msgstr ""

# MSG_AUTOLOAD_FILAMENT c=18
#: ultralcd.cpp:6635
msgid "AutoLoad filament"
msgstr "AutoZavedeni fil."

# MSG_AUTOLOADING_ONLY_IF_FSENS_ON c=20 r=4
#: ultralcd.cpp:4307
msgid "Autoloading filament available only when filament sensor is turned on..."
msgstr "Automaticke zavadeni filamentu je mozne pouze pri zapnutem filament senzoru..."

# MSG_AUTOLOADING_ENABLED c=20 r=4
#: ultralcd.cpp:2638
msgid "Autoloading filament is active, just press the knob and insert filament..."
msgstr "Automaticke zavadeni filamentu aktivni, stisknete tlacitko a vlozte filament..."

# MSG_SELFTEST_AXIS_LENGTH c=20
#: ultralcd.cpp:8076
msgid "Axis length"
msgstr "Delka osy"

# MSG_SELFTEST_AXIS c=16
#: ultralcd.cpp:8077
msgid "Axis"
msgstr "Osa"

# MSG_SELFTEST_BEDHEATER c=20
#: ultralcd.cpp:8034
msgid "Bed/Heater"
msgstr "Podlozka/Topeni"

# MSG_BED_DONE c=20
#: messages.c:15
msgid "Bed done"
msgstr "Bed OK."

# MSG_BED_HEATING c=20
#: messages.c:16
msgid "Bed Heating"
msgstr "Zahrivani bedu"

# MSG_BED_CORRECTION_MENU c=18
#: ultralcd.cpp:5780
msgid "Bed level correct"
msgstr "Korekce podlozky"

# MSG_BELTTEST c=18
#: ultralcd.cpp:5760
msgid "Belt test"
msgstr "Test remenu"

# MSG_BED_LEVELING_FAILED_POINT_LOW c=20 r=6
#: messages.c:17
msgid "Bed leveling failed. Sensor didn't trigger. Debris on nozzle? Waiting for reset."
msgstr "Kalibrace Z selhala. Sensor nesepnul. Znecistena tryska? Cekam na reset."

# MSG_BRIGHT c=6
#: messages.c:160
msgid "Bright"
msgstr "Jasny"

# MSG_BRIGHTNESS c=18
#: messages.c:156
msgid "Brightness"
msgstr "Podsviceni"

# MSG_BED c=13
#: messages.c:14
msgid "Bed"
msgstr "Podlozka"

# MSG_BELT_STATUS c=18
#: messages.c:19
msgid "Belt status"
msgstr "Stav remenu"

# MSG_RECOVER_PRINT c=20 r=2
#: messages.c:84
msgid "Blackout occurred. Recover print?"
msgstr "Detekovan vypadek proudu.Obnovit tisk?"

# MSG_CALIBRATING_HOME c=20
#: ultralcd.cpp:8395
msgid "Calibrating home"
msgstr "Kalibruji vychozi p."

# MSG_CALIBRATE_BED c=18
#: ultralcd.cpp:5769
msgid "Calibrate XYZ"
msgstr "Kalibrace XYZ"

# MSG_HOMEYZ c=18
#: messages.c:54
msgid "Calibrate Z"
msgstr "Kalibrovat Z"

# MSG_CANCEL2 c=10
#: messages.c:20
msgid ">Cancel"
msgstr ">Zrusit"

# MSG_MOVE_CARRIAGE_TO_THE_TOP c=20 r=8
#: ultralcd.cpp:3308
msgid "Calibrating XYZ. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
msgstr "Kalibrace XYZ. Otacenim tlacitka posunte Z osu az k~hornimu dorazu. Potvrdte tlacitkem."

# MSG_CALIBRATE_Z_AUTO c=20 r=2
#: messages.c:21
msgid "Calibrating Z"
msgstr "Kalibruji Z"

# MSG_MOVE_CARRIAGE_TO_THE_TOP_Z c=20 r=8
#: ultralcd.cpp:3308
msgid "Calibrating Z. Rotate the knob to move the Z carriage up to the end stoppers. Click when done."
msgstr "Kalibrace Z. Otacenim tlacitka posunte Z osu az k~hornimu dorazu. Potvrdte tlacitkem."

# MSG_HOMEYZ_DONE c=20
#: ultralcd.cpp:656
msgid "Calibration done"
msgstr "Kalibrace OK"

# MSG_MENU_CALIBRATION c=18
#: messages.c:70
msgid "Calibration"
msgstr "Kalibrace"

# MSG_SD_REMOVED c=20
#: ultralcd.cpp:8842
msgid "Card removed"
msgstr "Karta vyjmuta"

# MSG_CHECKING_FILE c=17
#: ultralcd.cpp:8483
msgid "Checking file"
msgstr "Kontroluji soubor"

# MSG_NOT_COLOR c=19
#: ultralcd.cpp:2555
msgid "Color not correct"
msgstr "Barva neni cista"

# MSG_COOLDOWN c=18
#: messages.c:27
msgid "Cooldown"
msgstr "Zchladit"

# MSG_COPY_SEL_LANG c=20 r=3
#: ultralcd.cpp:4425
msgid "Copy selected language?"
msgstr "Kopirovat vybrany jazyk?"

# MSG_CRASHDETECT c=13
#: messages.c:30
msgid "Crash det."
msgstr "Det. narazu"

# MSG_CHOOSE_FIL_1ST_LAYERCAL c=20 r=7
#: ultralcd.cpp:4824
msgid "Select a filament for the First Layer Calibration and select it in the on-screen menu."
msgstr "Zvolte filament pro kalibraci prvni vrstvy z nasledujiciho menu"

# MSG_CRASH_DETECTED c=20
#: messages.c:29
msgid "Crash detected."
msgstr "Detekovan naraz."

# MSG_CRASH_RESUME c=20 r=3
#: Marlin_main.cpp:651
msgid "Crash detected. Resume print?"
msgstr "Detekovan naraz. Obnovit tisk?"

# MSG_CRASH c=7
#: messages.c:28
msgid "Crash"
msgstr "Naraz"

# MSG_CURRENT c=19
#: ultralcd.cpp:5911
msgid "Current"
msgstr "Pouze aktualni"

# MSG_DATE c=17
#: ultralcd.cpp:1975
msgid "Date:"
msgstr "Datum:"

# MSG_COMMUNITY_MADE c=18
#: messages.c:25
msgid "Community made"
msgstr "Komunitni prekl."

# MSG_DISABLE_STEPPERS c=18
#: ultralcd.cpp:5660
msgid "Disable steppers"
msgstr "Vypnout motory"

# MSG_BABYSTEP_Z_NOT_SET c=20 r=12
#: messages.c:13
msgid "Distance between tip of the nozzle and the bed surface has not been set yet. Please follow the manual, chapter First steps, section First layer calibration."
msgstr "Neni zkalibrovana vzdalenost trysky od tiskove podlozky. Postupujte prosim podle manualu, kapitola Zaciname, odstavec Nastaveni prvni vrstvy."

# MSG_FS_CONTINUE c=5
#: messages.c:154
msgid "Cont."
msgstr "Pokr."

# MSG_WIZARD_REPEAT_V2_CAL c=20 r=7
#: ultralcd.cpp:5003
msgid "Do you want to repeat last step to readjust distance between nozzle and heatbed?"
msgstr "Chcete opakovat posledni krok a pozmenit vzdalenost mezi tryskou a podlozkou?"

# MSG_EXTRUDER_CORRECTION c=13
#: ultralcd.cpp:5072
msgid "E-correct:"
msgstr "Korekce E:"

# MSG_EJECT_FILAMENT c=16
#: messages.c:62
msgid "Eject filament"
msgstr "Vysunout fil."

# MSG_EJECTING_FILAMENT c=20
#: mmu.cpp:1415
msgid "Ejecting filament"
msgstr "Vysouvam filament"

# MSG_SELFTEST_ENDSTOP_NOTHIT c=20
#: ultralcd.cpp:8052
msgid "Endstop not hit"
msgstr "Kon. spinac nesepnut"

# MSG_SELFTEST_ENDSTOP c=16
#: ultralcd.cpp:8047
msgid "Endstop"
msgstr "Koncovy spinac"

# MSG_SELFTEST_ENDSTOPS c=20
#: ultralcd.cpp:8038
msgid "Endstops"
msgstr "Konc. spinace"

# MSG_STACK_ERROR c=20 r=4
#: 
msgid "Error - static memory has been overwritten"
msgstr "Chyba - Doslo k prepisu staticke pameti"

# MSG_CUT_FILAMENT c=16
#: messages.c:63
msgid "Cut filament"
msgstr "Ustrihnout"

# MSG_CUTTER c=9
#: messages.c:130
msgid "Cutter"
msgstr "Strihani"

# MSG_MMU_CUTTING_FIL c=18
#: mmu.cpp:1387
msgid "Cutting filament"
msgstr "Strihani filamentu"

# MSG_FSENS_NOT_RESPONDING c=20 r=4
#: ultralcd.cpp:4320
msgid "ERROR: Filament sensor is not responding, please check connection."
msgstr "CHYBA: Filament senzor nereaguje, zkontrolujte prosim zapojeni."

# MSG_DIM c=6
#: messages.c:161
msgid "Dim"
msgstr "Temny"

# MSG_ERROR c=10
#: messages.c:31
msgid "ERROR:"
msgstr "CHYBA:"

# MSG_EXTRUDER_FAN_SPEED c=16
#: messages.c:37
msgid "Extruder fan:"
msgstr "Levy vent.:"

# MSG_INFO_EXTRUDER c=18
#: ultralcd.cpp:2030
msgid "Extruder info"
msgstr ""

# MSG_EXTRUDER c=17
#: messages.c:32
msgid "Extruder"
msgstr ""

# MSG_MMU_FAIL_STATS c=18
#: ultralcd.cpp:6657
msgid "Fail stats MMU"
msgstr "Selhani MMU"

# MSG_FSENSOR_AUTOLOAD c=13
#: messages.c:50
msgid "F. autoload"
msgstr "F. autozav."

# MSG_FAIL_STATS c=18
#: ultralcd.cpp:6654
msgid "Fail stats"
msgstr "Selhani"

# MSG_FAN_SPEED c=14
#: messages.c:36
msgid "Fan speed"
msgstr "Rychlost vent."

# MSG_SELFTEST_FAN c=20
#: messages.c:93
msgid "Fan test"
msgstr "Test ventilatoru"

# MSG_FANS_CHECK c=13
#: messages.c:33
msgid "Fans check"
msgstr "Kontr. vent."

# MSG_FSENSOR c=12
#: messages.c:51
msgid "Fil. sensor"
msgstr "Fil. senzor"

# MSG_FIL_RUNOUTS c=15
#: messages.c:34
msgid "Fil. runouts"
msgstr "Vypadky filam."

# MSG_FILAMENT_CLEAN c=20 r=2
#: messages.c:39
msgid "Filament extruding & with correct color?"
msgstr "Filament vytlacen a spravne barvy?"

# MSG_NOT_LOADED c=19
#: ultralcd.cpp:2554
msgid "Filament not loaded"
msgstr "Filament nezaveden"

# MSG_SELFTEST_FILAMENT_SENSOR c=17
#: messages.c:99
msgid "Filament sensor"
msgstr "Senzor filamentu"

# MSG_FILAMENT_USED c=19
#: ultralcd.cpp:2703
msgid "Filament used"
msgstr "Spotrebovano filam."

# MSG_PRINT_TIME c=19
#: ultralcd.cpp:2704
msgid "Print time"
msgstr "Cas tisku"

# MSG_FS_ACTION c=10
#: messages.c:153
msgid "FS Action"
msgstr "FS reakce"

# MSG_FILE_INCOMPLETE c=20 r=3
#: ultralcd.cpp:8537
msgid "File incomplete. Continue anyway?"
msgstr "Soubor nekompletni. Pokracovat?"

# MSG_FINISHING_MOVEMENTS c=20
#: messages.c:47
msgid "Finishing movements"
msgstr "Dokoncovani pohybu"

# MSG_V2_CALIBRATION c=18
#: messages.c:126
msgid "First layer cal."
msgstr "Kal. prvni vrstvy"

# MSG_WIZARD_SELFTEST c=20 r=8
#: ultralcd.cpp:4924
msgid "First, I will run the selftest to check most common assembly problems."
msgstr "Nejdriv pomoci selftestu zkontoluji nejcastejsi chyby vznikajici pri sestaveni tiskarny."

# MSG_MMU_FIX_ISSUE c=20 r=4
#: mmu.cpp:727
msgid "Fix the issue and then press button on MMU unit."
msgstr "Opravte chybu a pote stisknete tlacitko na jednotce MMU."

# MSG_FLOW c=15
#: ultralcd.cpp:6791
msgid "Flow"
msgstr "Prutok"

# MSG_SELFTEST_COOLING_FAN c=20
#: messages.c:90
msgid "Front print fan?"
msgstr "Predni tiskovy vent?"

# MSG_BED_CORRECTION_FRONT c=14
#: ultralcd.cpp:3106
msgid "Front side[μm]"
msgstr "Vpredu [μm]"

# MSG_SELFTEST_FANS c=20
#: ultralcd.cpp:8082
msgid "Front/left fans"
msgstr "Predni/levy vent."

# MSG_SELFTEST_HEATERTHERMISTOR c=20
#: ultralcd.cpp:8030
msgid "Heater/Thermistor"
msgstr "Topeni/Termistor"

# MSG_BED_HEATING_SAFETY_DISABLED c=20 r=4
#: Marlin_main.cpp:9877
msgid "Heating disabled by safety timer."
msgstr "Zahrivani preruseno bezpecnostnim casovacem."

# MSG_HEATING_COMPLETE c=20
#: messages.c:53
msgid "Heating done."
msgstr "Zahrivani OK."

# MSG_HEATING c=20
#: messages.c:52
msgid "Heating"
msgstr "Zahrivani"

# MSG_WIZARD_WELCOME c=20 r=7
#: messages.c:123
msgid "Hi, I am your Original Prusa i3 printer. Would you like me to guide you through the setup process?"
msgstr "Dobry den, jsem vase tiskarna Original Prusa i3. Chcete abych Vas provedla kalibracnim procesem?"

# MSG_FILAMENTCHANGE c=18
#: messages.c:45
msgid "Change filament"
msgstr "Vymenit filament"

# MSG_CHANGE_SUCCESS c=20
#: ultralcd.cpp:2484
msgid "Change success!"
msgstr "Zmena uspesna!"

# MSG_CORRECTLY c=20
#: ultralcd.cpp:2552
msgid "Changed correctly?"
msgstr "Vymena ok?"

# MSG_SELFTEST_CHECK_BED c=20
#: messages.c:96
msgid "Checking bed"
msgstr "Kontrola podlozky"

# MSG_SELFTEST_CHECK_ENDSTOPS c=20
#: ultralcd.cpp:8384
msgid "Checking endstops"
msgstr "Kontrola endstopu"

# MSG_SELFTEST_CHECK_HOTEND c=20
#: ultralcd.cpp:8390
msgid "Checking hotend"
msgstr "Kontrola hotend"

# MSG_SELFTEST_CHECK_FSENSOR c=20
#: messages.c:97
msgid "Checking sensors"
msgstr "Kontrola senzoru"

# MSG_CHECKING_X c=20
#: messages.c:23
msgid "Checking X axis"
msgstr "Kontrola osy X"

# MSG_CHECKING_Y c=20
#: messages.c:24
msgid "Checking Y axis"
msgstr "Kontrola osy Y"

# MSG_SELFTEST_CHECK_Z c=20
#: ultralcd.cpp:8387
msgid "Checking Z axis"
msgstr "Kontrola osy Z"

# MSG_SELECT_EXTRUDER c=20
#: messages.c:56
msgid "Select extruder:"
msgstr "Vyberte extruder:"

# MSG_FILAMENT c=17
#: messages.c:35
msgid "Filament"
msgstr ""

# MSG_WIZARD_XYZ_CAL c=20 r=8
#: ultralcd.cpp:4933
msgid "I will run xyz calibration now. It will take approx. 12 mins."
msgstr "Nyni provedu xyz kalibraci. Zabere to priblizne 12 min."

# MSG_WIZARD_Z_CAL c=20 r=8
#: ultralcd.cpp:4941
msgid "I will run z calibration now."
msgstr "Nyni provedu z kalibraci."

# MSG_WATCH c=18
#: messages.c:118
msgid "Info screen"
msgstr "Informace"

# MSG_INSERT_FILAMENT c=20
#: ultralcd.cpp:2472
msgid "Insert filament"
msgstr "Vlozte filament"

# MSG_FILAMENT_LOADED c=20 r=2
#: messages.c:40
msgid "Is filament loaded?"
msgstr "Je filament zaveden?"

# MSG_STEEL_SHEET_CHECK c=20 r=2
#: messages.c:111
msgid "Is steel sheet on heatbed?"
msgstr "Je tiskovy plat na podlozce?"

# MSG_LAST_PRINT_FAILURES c=20
#: messages.c:59
msgid "Last print failures"
msgstr "Selhani posl. tisku"

# MSG_WIZARD_WELCOME_SHIPPING c=20 r=16
#: messages.c:124
msgid "Hi, I am your Original Prusa i3 printer. I will guide you through a short setup process, in which the Z-axis will be calibrated. Then, you will be ready to print."
msgstr "Ahoj, jsem vase tiskarna Original Prusa i3. Provedu vas kratkym procesem nastaveni, ve kterem zkalibrujeme osu Z. Pak budete moct zacit tisknout."

# MSG_ADDITIONAL_SHEETS c=20 r=9
#: ultralcd.cpp:5011
msgid "If you have additional steel sheets, calibrate their presets in Settings - HW Setup - Steel sheets."
msgstr "Mate-li vice tiskovych platu, kalibrujte je v menu Nastaveni - HW nastaveni - Tiskove platy"

# MSG_LAST_PRINT c=18
#: messages.c:58
msgid "Last print"
msgstr "Posledni tisk"

# MSG_SELFTEST_EXTRUDER_FAN c=20
#: messages.c:91
msgid "Left hotend fan?"
msgstr "Levy vent na trysce?"

# MSG_LEFT c=10
#: ultralcd.cpp:2834
msgid "Left"
msgstr "Vlevo"

# MSG_BED_CORRECTION_LEFT c=14
#: ultralcd.cpp:3104
msgid "Left side [μm]"
msgstr "Vlevo [μm]"

# MSG_LIN_CORRECTION c=18
#: ultralcd.cpp:5684
msgid "Lin. correction"
msgstr "Korekce lin."

# MSG_BABYSTEP_Z c=18
#: messages.c:12
msgid "Live adjust Z"
msgstr "Doladeni osy Z"

# MSG_INSERT_FIL c=20 r=6
#: ultralcd.cpp:7283
msgid "Insert the filament (do not load it) into the extruder and then press the knob."
msgstr "Vlozte filament (nezavadejte) do extruderu a stisknete tlacitko"

# MSG_LOAD_FILAMENT c=17
#: messages.c:60
msgid "Load filament"
msgstr "Zavest filament"

# MSG_LOADING_COLOR c=20
#: ultralcd.cpp:2506
msgid "Loading color"
msgstr "Cisteni barvy"

# MSG_LOADING_FILAMENT c=20
#: messages.c:61
msgid "Loading filament"
msgstr "Zavadeni filamentu"

# MSG_ITERATION c=12
#: messages.c:55
msgid "Iteration"
msgstr "Opakovani"

# MSG_LOOSE_PULLEY c=20
#: ultralcd.cpp:8070
msgid "Loose pulley"
msgstr "Uvolnena remenicka"

# MSG_LOAD_TO_NOZZLE c=18
#: ultralcd.cpp:6620
msgid "Load to nozzle"
msgstr "Zavest do trysky"

# MSG_M117_V2_CALIBRATION c=25
#: messages.c:64
msgid "M117 First layer cal."
msgstr "M117 Kal. prvni vrstvy"

# MSG_MAIN c=18
#: messages.c:65
msgid "Main"
msgstr "Hlavni nabidka"

# MSG_BL_HIGH c=12
#: messages.c:157
msgid "Level Bright"
msgstr "Normalni"

# MSG_BL_LOW c=12
#: messages.c:158
msgid "Level Dimmed"
msgstr "Ztlumeny"

# MSG_MEASURE_BED_REFERENCE_HEIGHT_LINE1 c=20 r=3
#: messages.c:69
msgid "Measuring reference height of calibration point"
msgstr "Merim referencni vysku kalibracniho bodu"

# MSG_MESH_BED_LEVELING c=18
#: messages.c:150
msgid "Mesh Bed Leveling"
msgstr ""

# MSG_MMU_OK_RESUMING_POSITION c=20 r=4
#: mmu.cpp:765
msgid "MMU OK. Resuming position..."
msgstr "MMU OK. Pokracuji v tisku..."

# MSG_MMU_OK_RESUMING_TEMPERATURE c=20 r=4
#: mmu.cpp:758
msgid "MMU OK. Resuming temperature..."
msgstr "MMU OK. Pokracuji v nahrivani..."

# MSG_MEASURED_SKEW c=14
#: ultralcd.cpp:2875
msgid "Measured skew"
msgstr "Merene zkos."

# MSG_MMU_FAILS c=15
#: messages.c:71
msgid "MMU fails"
msgstr "Selhani MMU"

# MSG_MMU_LOAD_FAILED c=20
#: mmu.cpp:1587
msgid "MMU load failed"
msgstr "Zavedeni MMU selhalo"

# MSG_MMU_LOAD_FAILS c=15
#: messages.c:72
msgid "MMU load fails"
msgstr "MMU selhani zav"

# MSG_MMU_OK_RESUMING c=20 r=4
#: mmu.cpp:776
msgid "MMU OK. Resuming..."
msgstr "MMU OK. Pokracuji..."

# MSG_MODE c=6
#: messages.c:105
msgid "Mode"
msgstr "Mod"

# MSG_MK3_FIRMWARE_ON_MK3S c=20 r=4
#: Marlin_main.cpp:882
msgid "MK3 firmware detected on MK3S printer"
msgstr "MK3 firmware detekovan na MK3S tiskarne"

# MSG_NORMAL c=7
#: messages.c:109
msgid "Normal"
msgstr ""

# MSG_SILENT c=7
#: messages.c:108
msgid "Silent"
msgstr "Tichy"

# MSG_MMU_USER_ATTENTION c=20 r=3
#: mmu.cpp:722
msgid "MMU needs user attention."
msgstr "MMU potrebuje zasah uzivatele."

# MSG_MMU_POWER_FAILS c=15
#: ultralcd.cpp:1507
msgid "MMU power fails"
msgstr "MMU vyp. proudu"

# MSG_STEALTH c=7
#: messages.c:110
msgid "Stealth"
msgstr "Tichy"

# MSG_AUTO_POWER c=10
#: messages.c:107
msgid "Auto power"
msgstr "Automat."

# MSG_HIGH_POWER c=10
#: messages.c:106
msgid "High power"
msgstr "Vys. vykon"

# MSG_MMU_CONNECTED c=18
#: ultralcd.cpp:1987
msgid "MMU2 connected"
msgstr "MMU2 pripojeno"

# MSG_SELFTEST_MOTOR c=18
#: messages.c:98
msgid "Motor"
msgstr ""

# MSG_MOVE_AXIS c=18
#: ultralcd.cpp:5659
msgid "Move axis"
msgstr "Posunout osu"

# MSG_MOVE_X c=18
#: ultralcd.cpp:4223
msgid "Move X"
msgstr "Posunout X"

# MSG_MOVE_Y c=18
#: ultralcd.cpp:4224
msgid "Move Y"
msgstr "Posunout Y"

# MSG_MOVE_Z c=18
#: ultralcd.cpp:4225
msgid "Move Z"
msgstr "Posunout Z"

# MSG_NO_MOVE c=20
#: Marlin_main.cpp:5852
msgid "No move."
msgstr "Bez pohybu."

# MSG_NO_CARD c=18
#: ultralcd.cpp:6600
msgid "No SD card"
msgstr "Zadna SD karta"

# MSG_NA c=3
#: messages.c:129
msgid "N/A"
msgstr ""

# MSG_NO c=4
#: messages.c:73
msgid "No"
msgstr "Ne"

# MSG_SELFTEST_NOTCONNECTED c=20
#: ultralcd.cpp:8031
msgid "Not connected"
msgstr "Nezapojeno"

# MSG_NEW_FIRMWARE_AVAILABLE c=20 r=2
#: util.cpp:195
msgid "New firmware version available:"
msgstr "Vysla nova verze firmware:"

# MSG_SELFTEST_FAN_NO c=19
#: messages.c:94
msgid "Not spinning"
msgstr "Netoci se"

# MSG_WIZARD_V2_CAL c=20 r=8
#: ultralcd.cpp:4820
msgid "Now I will calibrate distance between tip of the nozzle and heatbed surface."
msgstr "Nyni zkalibruji vzdalenost mezi koncem trysky a povrchem podlozky."

# MSG_WIZARD_WILL_PREHEAT c=20 r=4
#: ultralcd.cpp:4949
msgid "Now I will preheat nozzle for PLA."
msgstr "Nyni predehreji trysku pro PLA."

# MSG_NOZZLE c=12
#: messages.c:74
msgid "Nozzle"
msgstr "Tryska"

# MSG_DEFAULT_SETTINGS_LOADED c=20 r=6
#: Marlin_main.cpp:1605
msgid "Old settings found. Default PID, Esteps etc. will be set."
msgstr "Neplatne hodnoty nastaveni. Bude pouzito vychozi PID, Esteps atd."

# MSG_REMOVE_TEST_PRINT c=20 r=4
#: ultralcd.cpp:4940
msgid "Now remove the test print from steel sheet."
msgstr "Nyni odstrante testovaci vytisk z tiskoveho platu."

# MSG_PAUSE_PRINT c=18
#: messages.c:76
msgid "Pause print"
msgstr "Pozastavit tisk"

# MSG_PID_RUNNING c=20
#: ultralcd.cpp:1322
msgid "PID cal."
msgstr "PID kal."

# MSG_PID_FINISHED c=20
#: ultralcd.cpp:1328
msgid "PID cal. finished"
msgstr "PID kal. ukoncena"

# MSG_PID_EXTRUDER c=17
#: ultralcd.cpp:5781
msgid "PID calibration"
msgstr "PID kalibrace"

# MSG_PINDA_PREHEAT c=20
#: ultralcd.cpp:678
msgid "PINDA Heating"
msgstr "Nahrivani PINDA"

# MSG_PAPER c=20 r=10
#: messages.c:75
msgid "Place a sheet of paper under the nozzle during the calibration of first 4 points. If the nozzle catches the paper, power off the printer immediately."
msgstr "Umistete list papiru na podlozku a udrzujte jej pod tryskou behem mereni prvnich 4 bodu. Pokud tryska zachyti papir, okamzite vypnete tiskarnu."

# MSG_WIZARD_CLEAN_HEATBED c=20 r=8
#: ultralcd.cpp:5006
msgid "Please clean heatbed and then press the knob."
msgstr "Prosim ocistete podlozku a stisknete tlacitko."

# MSG_CONFIRM_NOZZLE_CLEAN c=20 r=8
#: messages.c:26
msgid "Please clean the nozzle for calibration. Click when done."
msgstr "Pro uspesnou kalibraci ocistete prosim tiskovou trysku. Potvrdte tlacitkem."

# MSG_SELFTEST_PLEASECHECK c=20
#: ultralcd.cpp:8025
msgid "Please check:"
msgstr "Zkontrolujte:"

# MSG_WIZARD_CALIBRATION_FAILED c=20 r=8
#: messages.c:119
msgid "Please check our handbook and fix the problem. Then resume the Wizard by rebooting the printer."
msgstr "Prosim nahlednete do prirucky 3D tiskare a opravte problem. Pote obnovte Pruvodce restartovanim tiskarny."

# MSG_CHECK_IDLER c=20 r=5
#: Marlin_main.cpp:3798
msgid "Please open idler and remove filament manually."
msgstr "Prosim otevrete idler a manualne odstrante filament."

# MSG_PLACE_STEEL_SHEET c=20 r=5
#: messages.c:77
msgid "Please place steel sheet on heatbed."
msgstr "Umistete prosim tiskovy plat na podlozku"

# MSG_PRESS_TO_UNLOAD c=20 r=4
#: messages.c:81
msgid "Please press the knob to unload filament"
msgstr "Pro vysunuti filamentu stisknete prosim tlacitko"

# MSG_PULL_OUT_FILAMENT c=20 r=4
#: messages.c:83
msgid "Please pull out filament immediately"
msgstr "Prosim vyjmete urychlene filament"

# MSG_EJECT_REMOVE c=20 r=4
#: mmu.cpp:1421
msgid "Please remove filament and then press the knob."
msgstr "Prosim vyjmete filament a pote stisknete tlacitko."

# MSG_REMOVE_STEEL_SHEET c=20 r=4
#: messages.c:86
msgid "Please remove steel sheet from heatbed."
msgstr "Odstrante prosim tiskovy plat z podlozky."

# MSG_RUN_XYZ c=20 r=4
#: Marlin_main.cpp:5338
msgid "Please run XYZ calibration first."
msgstr "Nejprve spustte kalibraci XYZ."

# MSG_UPDATE_MMU2_FW c=20 r=4
#: mmu.cpp:1341
msgid "Please update firmware in your MMU2. Waiting for reset."
msgstr "Prosim aktualizujte firmware ve vasi MMU2 jednotce. Cekam na reset."

# MSG_PLEASE_WAIT c=20
#: messages.c:78
msgid "Please wait"
msgstr "Prosim cekejte"

# MSG_REMOVE_SHIPPING_HELPERS c=20 r=3
#: ultralcd.cpp:4939
msgid "Please remove shipping helpers first."
msgstr "Nejprve prosim sundejte transportni soucastky."

# MSG_PREHEAT_NOZZLE c=20
#: messages.c:80
msgid "Preheat the nozzle!"
msgstr "Predehrejte trysku!"

# MSG_PREHEAT c=18
#: ultralcd.cpp:6558
msgid "Preheat"
msgstr "Predehrev"

# MSG_WIZARD_HEATING c=20 r=3
#: messages.c:121
msgid "Preheating nozzle. Please wait."
msgstr "Predehrev trysky. Prosim cekejte."

# MSG_NEW_FIRMWARE_PLEASE_UPGRADE c=20
#: util.cpp:199
msgid "Please upgrade."
msgstr "Prosim aktualizujte."

# MSG_PRESS_TO_PREHEAT c=20 r=4
#: Marlin_main.cpp:12052
msgid "Press the knob to preheat nozzle and continue."
msgstr "Pro nahrati trysky a pokracovani stisknete tlacitko."

# MSG_FS_PAUSE c=5
#: fsensor.cpp:730
msgid "Pause"
msgstr "Pauza"

# MSG_POWER_FAILURES c=15
#: messages.c:79
msgid "Power failures"
msgstr "Vypadky proudu"

# MSG_PRINT_ABORTED c=20
#: messages.c:82
msgid "Print aborted"
msgstr "Tisk prerusen"

# MSG_PREHEATING_TO_LOAD c=20
#: ultralcd.cpp:2287
msgid "Preheating to load"
msgstr "Predehrev k zavedeni"

# MSG_PREHEATING_TO_UNLOAD c=20
#: ultralcd.cpp:2292
msgid "Preheating to unload"
msgstr "Predehrev k vyjmuti"

# MSG_PRINT_FAN_SPEED c=16
#: messages.c:38
msgid "Print fan:"
msgstr "Tiskovy vent.:"

# MSG_CARD_MENU c=18
#: messages.c:22
msgid "Print from SD"
msgstr "Tisk z SD"

# MSG_PRESS_KNOB c=20
#: ultralcd.cpp:2120
msgid "Press the knob"
msgstr "Stisknete tlacitko"

# MSG_PRINT_PAUSED c=20
#: ultralcd.cpp:902
msgid "Print paused"
msgstr "Tisk pozastaven"

# MSG_RESUME_NOZZLE_TEMP c=20 r=4
#: mmu.cpp:726
msgid "Press the knob to resume nozzle temperature."
msgstr "Pro pokracovani nahrivani trysky stisknete tlacitko."

# MSG_FOLLOW_CALIBRATION_FLOW c=20 r=8
#: messages.c:48
msgid "Printer has not been calibrated yet. Please follow the manual, chapter First steps, section Calibration flow."
msgstr "Tiskarna nebyla jeste zkalibrovana. Postupujte prosim podle manualu, kapitola Zaciname, odstavec Postup kalibrace."

# MSG_WIZARD_LOAD_FILAMENT c=20 r=6
#: ultralcd.cpp:4800
msgid "Please insert filament into the extruder, then press the knob to load it."
msgstr "Prosim vlozte filament do extruderu a stisknete tlacitko k jeho zavedeni"

# MSG_MMU_INSERT_FILAMENT_FIRST_TUBE c=20 r=6
#: ultralcd.cpp:4795
msgid "Please insert filament into the first tube of the MMU, then press the knob to load it."
msgstr "Prosim vlozte filament do prvni trubicky MMU a stisknete tlacitko k jeho zavedeni"

# MSG_PLEASE_LOAD_PLA c=20 r=4
#: ultralcd.cpp:4717
msgid "Please load filament first."
msgstr "Prosim nejdriv zavedte filament"

# MSG_BED_CORRECTION_REAR c=14
#: ultralcd.cpp:3107
msgid "Rear side [μm]"
msgstr "Vzadu [μm]"

# MSG_UNLOAD_FILAMENT_REPEAT c=20 r=4
#: ultralcd.cpp:7307
msgid "Please unload the filament first, then repeat this action."
msgstr "Prosim vyjmete filament a zopakujte tuto akci"

# MSG_CHECK_IR_CONNECTION c=20 r=4
#: ultralcd.cpp:7310
msgid "Please check the IR sensor connection, unload filament if present."
msgstr "Prosim zkontrolujte zapojeni IR senzoru a vyjmuty filament"

# MSG_RECOVERING_PRINT c=20
#: Marlin_main.cpp:11396
msgid "Recovering print"
msgstr "Obnovovani tisku"

# MSG_REMOVE_OLD_FILAMENT c=20 r=5
#: mmu.cpp:833
msgid "Remove old filament and press the knob to start loading new filament."
msgstr "Vyjmete stary filament a stisknete tlacitko pro zavedeni noveho."

# MSG_CALIBRATE_BED_RESET c=18
#: ultralcd.cpp:5786
msgid "Reset XYZ calibr."
msgstr "Reset XYZ kalibr."

# MSG_RESET c=14
#: messages.c:87
msgid "Reset"
msgstr ""

# MSG_RESUME_PRINT c=18
#: messages.c:88
msgid "Resume print"
msgstr "Pokracovat"

# MSG_RESUMING_PRINT c=20
#: messages.c:89
msgid "Resuming print"
msgstr "Obnoveni tisku"

# MSG_BED_CORRECTION_RIGHT c=14
#: ultralcd.cpp:3105
msgid "Right side[μm]"
msgstr "Vpravo [μm]"

# MSG_RPI_PORT c=13
#: messages.c:144
msgid "RPi port"
msgstr ""

# MSG_WIZARD_RERUN c=20 r=7
#: ultralcd.cpp:4738
msgid "Running Wizard will delete current calibration results and start from the beginning. Continue?"
msgstr "Spusteni Pruvodce vymaze ulozene vysledky vsech kalibraci a spusti kalibracni proces od zacatku. Pokracovat?"

# MSG_SD_CARD c=8
#: messages.c:140
msgid "SD card"
msgstr "SD karta"

# MSG_RIGHT c=10
#: ultralcd.cpp:2835
msgid "Right"
msgstr "Vpravo"

# MSG_FIND_BED_OFFSET_AND_SKEW_LINE1 c=20 r=3
#: messages.c:46
msgid "Searching bed calibration point"
msgstr "Hledam kalibracni bod podlozky"

# MSG_LANGUAGE_SELECT c=18
#: ultralcd.cpp:4441
msgid "Select language"
msgstr "Vyber jazyka"

# MSG_SELFTEST_OK c=20
#: ultralcd.cpp:7582
msgid "Self test OK"
msgstr ""

# MSG_SELFTEST_START c=20
#: ultralcd.cpp:7350
msgid "Self test start"
msgstr ""

# MSG_SELFTEST c=18
#: ultralcd.cpp:5762
msgid "Selftest"
msgstr ""

# MSG_SELFTEST_ERROR c=20
#: ultralcd.cpp:8024
msgid "Selftest error!"
msgstr "Chyba Selftestu!"

# MSG_SELFTEST_FAILED c=20
#: messages.c:92
msgid "Selftest failed"
msgstr "Selftest selhal"

# MSG_FORCE_SELFTEST c=20 r=8
#: Marlin_main.cpp:1637
msgid "Selftest will be run to calibrate accurate sensorless rehoming."
msgstr "Pro kalibraci presneho rehomovani bude nyni spusten selftest."

# MSG_SEL_PREHEAT_TEMP c=20 r=6
#: ultralcd.cpp:4980
msgid "Select nozzle preheat temperature which matches your material."
msgstr "Vyberte teplotu predehrati trysky ktera odpovida vasemu materialu."

# MSG_SET_TEMPERATURE c=20
#: ultralcd.cpp:3125
msgid "Set temperature:"
msgstr "Nastavte teplotu:"

# MSG_SETTINGS c=18
#: messages.c:101
msgid "Settings"
msgstr "Nastaveni"

# MSG_SHOW_END_STOPS c=18
#: ultralcd.cpp:5783
msgid "Show end stops"
msgstr "Stav konc. spin."

# MSG_FILE_CNT c=20 r=6
#: cardreader.cpp:817
msgid "Some files will not be sorted. Max. No. of files in 1 folder for sorting is 100."
msgstr "Nektere soubory nebudou setrideny. Maximalni pocet souboru ve slozce pro setrideni je 100."

# MSG_SORT c=7
#: messages.c:141
msgid "Sort"
msgstr "Trideni"

# MSG_NONE c=8
#: messages.c:131
msgid "None"
msgstr "Zadne"

# MSG_SORT_TIME c=8
#: messages.c:142
msgid "Time"
msgstr "Cas"

# MSG_SEVERE_SKEW c=14
#: ultralcd.cpp:2878
msgid "Severe skew"
msgstr "Tezke zkos."

# MSG_SORT_ALPHA c=8
#: messages.c:143
msgid "Alphabet"
msgstr "Abeceda"

# MSG_SORTING c=20
#: cardreader.cpp:880
msgid "Sorting files"
msgstr "Trideni souboru"

# MSG_SOUND_LOUD c=7
#: messages.c:146
msgid "Loud"
msgstr "Hlasity"

# MSG_SLIGHT_SKEW c=14
#: ultralcd.cpp:2877
msgid "Slight skew"
msgstr "Lehke zkos."

# MSG_SOUND c=7
#: messages.c:145
msgid "Sound"
msgstr "Zvuk"

# MSG_RUNOUTS c=7
#: ultralcd.cpp:1583
msgid "Runouts"
msgstr ""

# MSG_Z-LEVELING_ENFORCED c=20 r=4
#: Marlin_main.cpp:3303
msgid "Some problem encountered, Z-leveling enforced ..."
msgstr "Vyskytl se problem, srovnavam osu Z ..."

# MSG_SOUND_ONCE c=7
#: messages.c:147
msgid "Once"
msgstr "Jednou"

# MSG_SPEED c=15
#: ultralcd.cpp:6785
msgid "Speed"
msgstr "Rychlost"

# MSG_SELFTEST_FAN_YES c=19
#: messages.c:95
msgid "Spinning"
msgstr "Toci se"

# MSG_TEMP_CAL_WARNING c=20 r=4
#: Marlin_main.cpp:5351
msgid "Stable ambient temperature 21-26C is needed a rigid stand is required."
msgstr "Je vyzadovana stabilni pokojova teplota 21-26C a pevna podlozka."

# MSG_STATISTICS c=18
#: ultralcd.cpp:6063
msgid "Statistics"
msgstr "Statistika"

# MSG_STOP_PRINT c=18
#: messages.c:112
msgid "Stop print"
msgstr "Zastavit tisk"

# MSG_STOPPED c=20
#: messages.c:113
msgid "STOPPED."
msgstr "ZASTAVENO."

# MSG_SUPPORT c=18
#: ultralcd.cpp:6659
msgid "Support"
msgstr "Podpora"

# MSG_SELFTEST_SWAPPED c=16
#: ultralcd.cpp:8083
msgid "Swapped"
msgstr "Prohozene"

# MSG_SELECT_FILAMENT c=20
#: messages.c:57
msgid "Select filament:"
msgstr "Zvolte filament:"

# MSG_PINDA_CALIBRATION c=13
#: messages.c:114
msgid "PINDA cal."
msgstr "PINDA kal."

# MSG_SELECT_TEMP_MATCHES_MATERIAL c=20 r=4
#: ultralcd.cpp:4829
msgid "Select temperature which matches your material."
msgstr "Zvolte teplotu, ktera odpovida vasemu materialu."

# MSG_PINDA_CAL_FAILED c=20 r=4
#: ultralcd.cpp:3761
msgid "PINDA calibration failed"
msgstr "PINDA kalibrace selhala"

# MSG_PINDA_CALIBRATION_DONE c=20 r=8
#: messages.c:115
msgid "PINDA calibration is finished and active. It can be disabled in menu Settings->PINDA cal."
msgstr "PINDA kalibrace dokoncena a je nyni aktivni. Zabere je mozno deaktivovat v menu Nastaveni->Tepl. kal."

# MSG_FS_VERIFIED c=20 r=3
#: ultralcd.cpp:7314
msgid "Sensor verified, remove the filament now."
msgstr "Senzor overen, vyjmete filament."

# MSG_TEMPERATURE c=18
#: ultralcd.cpp:5655
msgid "Temperature"
msgstr "Teplota"

# MSG_MENU_TEMPERATURES c=15
#: ultralcd.cpp:2037
msgid "Temperatures"
msgstr "Teploty"

# MSG_FOLLOW_Z_CALIBRATION_FLOW c=20 r=9
#: messages.c:49
msgid "There is still a need to make Z calibration. Please follow the manual, chapter First steps, section Calibration flow."
msgstr "Je potreba kalibrovat osu Z. Prosim postupujte dle prirucky, kapitola Zaciname, sekce Postup kalibrace."

# MSG_TOTAL_FILAMENT c=19
#: ultralcd.cpp:2725
msgid "Total filament"
msgstr "Filament celkem"

# MSG_TOTAL_PRINT_TIME c=19
#: ultralcd.cpp:2726
msgid "Total print time"
msgstr "Celkovy cas tisku"

# MSG_TUNE c=18
#: ultralcd.cpp:6556
msgid "Tune"
msgstr "Ladit"

# MSG_TOTAL_FAILURES c=20
#: messages.c:103
msgid "Total failures"
msgstr "Celkem selhani"

# MSG_TO_LOAD_FIL c=20
#: ultralcd.cpp:2127
msgid "to load filament"
msgstr "k zavedeni filamentu"

# MSG_TO_UNLOAD_FIL c=20
#: ultralcd.cpp:2131
msgid "to unload filament"
msgstr "k vyjmuti filamentu"

# MSG_UNLOAD_FILAMENT c=18
#: messages.c:116
msgid "Unload filament"
msgstr "Vyjmout filament"

# MSG_UNLOADING_FILAMENT c=20
#: messages.c:117
msgid "Unloading filament"
msgstr "Vysouvam filament"

# MSG_TOTAL c=6
#: messages.c:102
msgid "Total"
msgstr "Celkem"

# MSG_USED c=19
#: ultralcd.cpp:5910
msgid "Used during print"
msgstr "Pouzite behem tisku"

# MSG_MENU_VOLTAGES c=15
#: ultralcd.cpp:2040
msgid "Voltages"
msgstr "Napeti"

# MSG_UNKNOWN c=13
#: ultralcd.cpp:1995
msgid "unknown"
msgstr "neznamy"

# MSG_USERWAIT c=20
#: Marlin_main.cpp:4347
msgid "Wait for user..."
msgstr "Ceka se na uzivatele"

# MSG_WAITING_TEMP c=20 r=4
#: ultralcd.cpp:3273
msgid "Waiting for nozzle and bed cooling"
msgstr "Cekani na zchladnuti trysky a podlozky."

# MSG_WAITING_TEMP_PINDA c=20 r=3
#: ultralcd.cpp:3234
msgid "Waiting for PINDA probe cooling"
msgstr "Cekani na zchladnuti PINDA"

# MSG_CHANGED_BOTH c=20 r=4
#: Marlin_main.cpp:1597
msgid "Warning: both printer type and motherboard type changed."
msgstr "Varovani: doslo ke zmene typu tiskarny a motherboardu."

# MSG_CHANGED_MOTHERBOARD c=20 r=4
#: Marlin_main.cpp:1589
msgid "Warning: motherboard type changed."
msgstr "Varovani: doslo ke zmene typu motherboardu."

# MSG_CHANGED_PRINTER c=20 r=4
#: Marlin_main.cpp:1593
msgid "Warning: printer type changed."
msgstr "Varovani: doslo ke zmene typu tiskarny."

# MSG_UNLOAD_SUCCESSFUL c=20 r=2
#: Marlin_main.cpp:3789
msgid "Was filament unload successful?"
msgstr "Bylo vysunuti filamentu uspesne?"

# MSG_SELFTEST_WIRINGERROR c=18
#: messages.c:100
msgid "Wiring error"
msgstr "Chyba zapojeni"

# MSG_WIZARD c=17
#: ultralcd.cpp:5753
msgid "Wizard"
msgstr "Pruvodce"

# MSG_XYZ_DETAILS c=18
#: ultralcd.cpp:2029
msgid "XYZ cal. details"
msgstr "Detaily XYZ kal."

# MSG_BED_SKEW_OFFSET_DETECTION_FITTING_FAILED c=20 r=8
#: messages.c:18
msgid "XYZ calibration failed. Please consult the manual."
msgstr "Kalibrace XYZ selhala. Nahlednete do manualu."

# MSG_YES c=4
#: messages.c:125
msgid "Yes"
msgstr "Ano"

# MSG_WIZARD_QUIT c=20 r=8
#: messages.c:122
msgid "You can always resume the Wizard from Calibration -> Wizard."
msgstr "Pruvodce muzete kdykoliv znovu spustit z menu Kalibrace -> Pruvodce"

# MSG_BED_SKEW_OFFSET_DETECTION_SKEW_EXTREME c=20 r=8
#: ultralcd.cpp:3733
msgid "XYZ calibration all right. Skew will be corrected automatically."
msgstr "Kalibrace XYZ v poradku. Zkoseni bude automaticky vyrovnano pri tisku."

# MSG_BED_SKEW_OFFSET_DETECTION_SKEW_MILD c=20 r=8
#: ultralcd.cpp:3730
msgid "XYZ calibration all right. X/Y axes are slightly skewed. Good job!"
msgstr "Kalibrace XYZ v poradku. X/Y osy mirne zkosene. Dobra prace!"

# MSG_TIMEOUT c=12
#: messages.c:159
msgid "Timeout"
msgstr ""

# MSG_X_CORRECTION c=13
#: ultralcd.cpp:5068
msgid "X-correct:"
msgstr "Korekce X:"

# MSG_BED_SKEW_OFFSET_DETECTION_PERFECT c=20 r=8
#: ultralcd.cpp:3727
msgid "XYZ calibration ok. X/Y axes are perpendicular. Congratulations!"
msgstr "Kalibrace XYZ v poradku. X/Y osy jsou kolme. Gratuluji!"

# MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_BOTH_FAR c=20 r=8
#: ultralcd.cpp:3711
msgid "XYZ calibration compromised. Front calibration points not reachable."
msgstr "Kalibrace XYZ nepresna. Predni kalibracni body moc vpredu."

# MSG_BED_SKEW_OFFSET_DETECTION_WARNING_FRONT_RIGHT_FAR c=20 r=8
#: ultralcd.cpp:3714
msgid "XYZ calibration compromised. Right front calibration point not reachable."
msgstr "Kalibrace XYZ nepresna. Pravy predni bod moc vpredu."

# MSG_LOAD_ALL c=17
#: ultralcd.cpp:6149
msgid "Load all"
msgstr "Zavest vse"

# MSG_BED_SKEW_OFFSET_DETECTION_POINT_NOT_FOUND c=20 r=6
#: ultralcd.cpp:3693
msgid "XYZ calibration failed. Bed calibration point was not found."
msgstr "Kalibrace XYZ selhala. Kalibracni bod podlozky nenalezen."

# MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_BOTH_FAR c=20 r=6
#: ultralcd.cpp:3699
msgid "XYZ calibration failed. Front calibration points not reachable."
msgstr "Kalibrace XYZ selhala. Predni kalibracni body moc vpredu. Srovnejte tiskarnu."

# MSG_BED_SKEW_OFFSET_DETECTION_FAILED_FRONT_RIGHT_FAR c=20 r=6
#: ultralcd.cpp:3702
msgid "XYZ calibration failed. Right front calibration point not reachable."
msgstr "Kalibrace XYZ selhala. Pravy predni bod moc vpredu. Srovnejte tiskarnu."

# MSG_Y_DIST_FROM_MIN c=20
#: ultralcd.cpp:2832
msgid "Y distance from min"
msgstr "Y vzdalenost od min"

# MSG_WIZARD_V2_CAL_2 c=20 r=12
#: ultralcd.cpp:4832
msgid "The printer will start printing a zig-zag line. Rotate the knob until you reach the optimal height. Check the pictures in the handbook (Calibration chapter)."
msgstr "Tiskarna zacne tisknout lomenou caru. Otacenim tlacitka nastavte optimalni vysku. Postupujte podle obrazku v handbooku (kapitola Kalibrace)."

# MSG_FIL_FAILED c=20 r=5
#: ultralcd.cpp:7318
msgid "Verification failed, remove the filament and try again."
msgstr "Overeni selhalo, vyjmete filament a zkuste znovu."

# MSG_Y_CORRECTION c=13
#: ultralcd.cpp:5069
msgid "Y-correct:"
msgstr "Korekce Y:"

# MSG_OFF c=3
#: messages.c:127
msgid "Off"
msgstr "Vyp"

# MSG_ON c=3
#: messages.c:128
msgid "On"
msgstr "Zap"

# MSG_BACK c=18
#: messages.c:66
msgid "Back"
msgstr "Zpet"

# MSG_CHECKS c=18
#: ultralcd.cpp:5623
msgid "Checks"
msgstr "Kontrola"

# MSG_FALSE_TRIGGERING c=20
#: ultralcd.cpp:8093
msgid "False triggering"
msgstr "Falesne spusteni"

# MSG_STRICT c=8
#: messages.c:133
msgid "Strict"
msgstr "Prisne"

# MSG_WARN c=8
#: messages.c:132
msgid "Warn"
msgstr "Varovat"

# MSG_HW_SETUP c=18
#: messages.c:104
msgid "HW Setup"
msgstr "HW nastaveni"

# MSG_MAGNETS_COMP c=13
#: messages.c:152
msgid "Magnets comp."
msgstr "Komp. magnetu"

# MSG_MESH c=12
#: messages.c:149
msgid "Mesh"
msgstr ""

# MSG_MK3S_FIRMWARE_ON_MK3 c=20 r=4
#: Marlin_main.cpp:875
msgid "MK3S firmware detected on MK3 printer"
msgstr "MK3S firmware detekovan na tiskarne MK3"

# MSG_MMU_MODE c=8
#: messages.c:139
msgid "MMU Mode"
msgstr "MMU mod"

# MSG_MODE_CHANGE_IN_PROGRESS c=20 r=3
#: ultralcd.cpp:4356
msgid "Mode change in progress..."
msgstr "Probiha zmena modu..."

# MSG_MODEL c=8
#: messages.c:134
msgid "Model"
msgstr ""

# MSG_NOZZLE_DIAMETER c=10
#: messages.c:138
msgid "Nozzle d."
msgstr "Tryska"

# MSG_GCODE_DIFF_CONTINUE c=20 r=4
#: util.cpp:414
msgid "G-code sliced for a different level. Continue?"
msgstr "G-code je pripraven pro jinou verzi. Pokracovat?"

# MSG_GCODE_DIFF_CANCELLED c=20 r=7
#: util.cpp:420
msgid "G-code sliced for a different level. Please re-slice the model again. Print cancelled."
msgstr "G-code je pripraven pro jinou verzi. Prosim preslicujte model znovu. Tisk zrusen."

# MSG_GCODE_DIFF_PRINTER_CONTINUE c=20 r=5
#: messages.c:136
msgid "G-code sliced for a different printer type. Continue?"
msgstr "G-code je pripraven pro jiny typ tiskarny. Pokracovat?"

# MSG_GCODE_DIFF_PRINTER_CANCELLED c=20 r=8
#: messages.c:137
msgid "G-code sliced for a different printer type. Please re-slice the model again. Print cancelled."
msgstr "G-code je pripraven pro jiny typ tiskarny. Prosim preslicujte model znovu. Tisk zrusen."

# MSG_GCODE_NEWER_FIRMWARE_CONTINUE c=20 r=5
#: util.cpp:381
msgid "G-code sliced for a newer firmware. Continue?"
msgstr "G-code je pripraven pro novejsi firmware. Pokracovat?"

# MSG_GCODE_NEWER_FIRMWARE_CANCELLED c=20 r=8
#: util.cpp:387
msgid "G-code sliced for a newer firmware. Please update the firmware. Print cancelled."
msgstr "G-code je pripraven pro novejsi firmware. Prosim aktualizujte firmware. Tisk zrusen."

# MSG_PREHEATING_TO_CUT c=20
#: ultralcd.cpp:2299
msgid "Preheating to cut"
msgstr "Predehrev ke strihu"

# MSG_PREHEATING_TO_EJECT c=20
#: ultralcd.cpp:2296
msgid "Preheating to eject"
msgstr "Predehrev k vysunuti"

# MSG_NOZZLE_DIFFERS_CONTINUE c=20 r=5
#: util.cpp:294
msgid "Printer nozzle diameter differs from the G-code. Continue?"
msgstr "Prumer trysky tiskarny se lisi od G-code. Pokracovat?"

# MSG_NOZZLE_DIFFERS_CANCELLED c=20 r=9
#: util.cpp:301
msgid "Printer nozzle diameter differs from the G-code. Please check the value in settings. Print cancelled."
msgstr "Prumer trysky tiskarny se lisi od G-code. Prosim zkontrolujte nastaveni. Tisk zrusen."

# MSG_SELFTEST_FS_LEVEL c=20
#: ultralcd.cpp:8098
msgid "%s level expected"
msgstr "%s ocekavana verze"

# MSG_RENAME c=18
#: ultralcd.cpp:6482
msgid "Rename"
msgstr "Prejmenovat"

# MSG_SELECT c=18
#: ultralcd.cpp:6475
msgid "Select"
msgstr "Vybrat"

# MSG_INFO_SENSORS c=18
#: ultralcd.cpp:2031
msgid "Sensor info"
msgstr "Senzor info"

# MSG_SHEET c=10
#: messages.c:67
msgid "Sheet"
msgstr "Plat"

# MSG_SOUND_BLIND c=7
#: messages.c:148
msgid "Assist"
msgstr "Asist."

# MSG_STEEL_SHEET c=18
#: messages.c:68
msgid "Steel sheets"
msgstr "Tiskove platy"

# MSG_Z_CORRECTION c=13
#: ultralcd.cpp:5070
msgid "Z-correct:"
msgstr "Korekce Z:"

# MSG_Z_PROBE_NR c=14
#: messages.c:151
msgid "Z-probe nr."
msgstr "Pocet mereni Z"

# MSG_PRINTER_IP c=18
#: ultralcd.cpp:2018
msgid "Printer IP Addr:"
msgstr "IP adr. tiskarny:"