1606 Commits

Author	SHA1	Message	Date
Gabe Rosenhouse	b45beeffd6	typo fix in Makefile	2014-02-16 23:23:29 -08:00
Paul Telford	306588925d	Add whitespace to M114 output	2014-02-16 21:01:19 -08:00
whosawhatsis	c43838bb1e	disable auto retract by default ... This should make it safe to enable FWRETRACT by default, with autoretract (which should now be fixed) only enabled by M209. FWRETRACT should probably now default to enabled (to make G10/G11 and M207-209 available, without changing functionality when they are not used), but I’ll save that for another pull request/discussion.	2014-02-16 19:04:54 -08:00
whosawhatsis	99f0e44864	Move FWRETRACT defaults to configuration_adv.h	2014-02-16 19:00:28 -08:00
whosawhatsis	66e3869138	Fix autoretract ... This takes the (now working) G10/G11 code and moves it to a function, which is called by G10 and G11, and also called by G1 if autoretract is enabled and a retract/recover move is detected.	2014-02-16 18:59:04 -08:00
whosawhatsis	2f2459c0db	Fix G10/G11 Z-lift	2014-02-16 18:15:34 -08:00
Gabe Rosenhouse	8c5675c290	Use language.h instead of English literals for "bed"	2014-02-16 17:16:00 -08:00
Gabe Rosenhouse	0f7393a13e	Refactor 'accurate' auto bed leveling to use probe_pt()	2014-02-16 10:44:15 -08:00
Gabe Rosenhouse	c4fbb44d6d	Refactor 3-point auto bed leveling to use probe_pt()	2014-02-16 10:44:08 -08:00
Gabe Rosenhouse	ad2c6488c7	Add probe_pt(), useful for auto bed leveling	2014-02-16 10:38:29 -08:00
Peter	c9c83a4560	Updated gen3+ board pins names to current convention	2014-02-16 00:47:06 +13:00
Mark Hanford	ab0d3c4fb3	Various typo fixes - only in comments, no code changes.	2014-02-14 11:48:24 +00:00
Josef Pavlik	477b6fa1df	move engaged from lcd console refreshes power off timeout	2014-02-14 12:37:21 +01:00
Josef Pavlik	831fc2a952	Pt100 and Pt1000 temperature sensors handling	2014-02-14 12:26:27 +01:00
nothinman	7dcd350941	A few changes to Russian, changed LCD strings to be <=17 characters.	2014-02-13 11:58:14 +00:00
daid	c31bb2b7ad	Only show the ZProbe offset when auto-bed-leveling is enabled.	2014-02-13 11:48:55 +01:00
daid	46f5bea19f	Add configurable beep for UltiPanel.	2014-02-13 11:17:33 +01:00
daid	d16a770855	Ultimainboard 2.x does not has a PS_ON pin.	2014-02-13 10:57:03 +01:00
daid	71bb3a8133	Add comments for Ultimainboard 2.0 configuration.	2014-02-13 10:53:46 +01:00
daid	9b7d87e885	Remove duplicate contrast define.	2014-02-13 10:50:17 +01:00
daid	816f0a678a	Merge pull request #768 from whosawhatsis/Marlin_v1 ... multiple FWretract fixes	2014-02-13 09:14:57 +01:00
whosawhatsis	6e43398509	G10/G11 bugfixes ... Previous version was broken by using G92 E0 between retract and recover.	2014-02-12 13:03:00 -08:00
whosawhatsis	d6c5c503d4	correct feedrate units in comments for M207/M208	2014-02-12 13:02:47 -08:00
nothinman	15d6116188	Merge pull request #689 from cajun-rat/tidy ... Use C++ initialization list	2014-02-12 16:38:11 +00:00
Martin Lukasik	0b9ecf3824	Language cleanup, part 1.	2014-02-12 13:21:26 +00:00
whosawhatsis	b5ba5c1465	Merge branch 'Marlin_v1' of https://github.com/whosawhatsis/Marlin into Marlin_v1	2014-02-11 19:06:03 -08:00
whosawhatsis	78e7654601	Keep FWRETRACT values in terms of millimeters when using M200 ... for volumetric E units	2014-02-11 19:05:35 -08:00
whosawhatsis	3f6d44d40b	Keep FWRETRACT values in terms of millimeters when using M200 for volumetric E units	2014-02-11 18:50:11 -08:00
Cylindric	363dc2f0e8	Merge branch 'Marlin_v1' into update_menu_plan	2014-02-12 00:51:16 +00:00
nothinman	5f797ca29f	Updated Polish, changed default firmware URL to Marlin.	2014-02-11 22:38:01 +00:00
Mark Hanford	0778f5f028	Add missing entries to the new Aragonian language.	2014-02-11 14:40:53 +00:00
Mark Hanford	54bab3e0d0	Merge branch 'Marlin_v1' into localisation ... Conflicts: Marlin/language.h	2014-02-11 14:35:28 +00:00
Mark Hanford	bdd0211aeb	Move strings in ultralcd.cpp into language.h.	2014-02-11 13:54:43 +00:00
Daniel Martinez	c8e5a82d49	keep English as default lang.	2014-02-09 18:24:24 +01:00
Daniel Martinez	f64592e362	Add Aragonese translation	2014-02-09 18:19:37 +01:00
ErikZalm	ac74f45dc0	Merge pull request #752 from MatixYo/patch-3 ... Update language.h	2014-02-09 17:52:26 +01:00
MatixYo	36086d3ca4	Update language.h ... Updated Polish translations.	2014-02-07 19:15:51 +01:00
Cylindric	1781031f2d	Update LCD Menu Tree with current options, based on ultralcd.cpp and language.h.	2014-02-07 01:52:44 +00:00
Jim Morris	d485988bec	fix typo	2014-02-05 14:39:45 -08:00
Jim Morris	8a1fd25363	Default is to not define digipot_i2c	2014-02-05 14:28:23 -08:00
Jim Morris	5097c57d3a	Added pins for Azteeg X3 Pro under motherboard 68	2014-02-05 14:25:42 -08:00
Jim Morris	b819fc53ca	Add Azteeg X3 Pro as motherboard 68 ... Add digipot i2c control for MCP4451 Allow M907 to set i2c digipot currents in amps Fix Makefile to allow Azteeg motherboards Fix Makefile to allow Wire libraries only Add beeper pin for Azteeg X3 Pro	2014-02-05 01:47:12 -08:00
ErikZalm	e1ae7952eb	Merge pull request #743 from Opticalworm/Marlin_v1 ... Improved support for panelolu2 encoder and buzzer	2014-02-03 12:33:10 -08:00
David Forrest	a5f53f0cf3	Heater wattage reporting for M105 using EXTRUDER_WATTS and BED_WATTS	2014-02-03 14:50:28 -05:00
Ronald	8d162e5bd7	Improved support for panelolu2 encoder and buzzer ... I added #define for LCD_FEEDBACK_FREQUENCY_HZ and LCD_FEEDBACK_FREQUENCY_DURATION_MS which is used to alter the default buzzer sound. When selecting Panelolu2 in configuration.h: - it automatically sets the correct ENCODER_PULSES_PER_STEP and ENCODER_STEPS_PER_MENU_ITEM. - if LCD_USE_I2C_BUZZER is defined it will also set the default LCD_FEEDBACK_FREQUENCY_HZ and LCD_FEEDBACK_FREQUENCY_DURATION_MS When selecting the sanguinololu 1284p the following is true: - its now enables LARGE_FLASH - It enables the gcode M300 when the panelolu2 LCD_USE_I2C_BUZZER is defined	2014-02-03 07:45:03 +00:00
whosawhatsis	b2c11ba980	Change diameter code to 'D' ... For some reason that I can’t figure out, the decimal is dropped when using ’S’ for the code. Also some minor code improvements to M200.	2014-02-01 18:49:25 -08:00
ErikZalm	61059385a3	Merge pull request #737 from whosawhatsis/M200 ... M200 implementation	2014-02-01 10:37:49 -08:00
whosawhatsis	856edfcc0d	Fixed math ... This is why I wanted to sleep on the code I wrote while falling asleep rather than immediately submitting a pull request.	2014-01-31 08:43:11 -08:00
ErikZalm	0d81ae77bc	Merge pull request #727 from drf5n/oversampling ... temperature.cpp: Actually use OVERSAMPLENR in the oversampling calculation.	2014-01-31 07:09:10 -08:00
ErikZalm	84df13f7d1	Merge pull request #721 from drf5n/lcdOnly ... Enable basic ULTRA_LCD screen w/o encoders and menus.	2014-01-31 07:07:12 -08:00
ErikZalm	4c7e9502ad	Merge pull request #718 from drf5n/temptableRes ... createTemperatureLookupMarlin.py: Add resolution comments and format for...	2014-01-31 07:06:02 -08:00
ErikZalm	652a0f6b5a	Merge pull request #717 from drf5n/tpins2 ... fastio.h: Add AT90USBxx_TEENSYPP_ASSIGNMENTS for teensyduino/Lincomatic/...	2014-01-31 07:05:20 -08:00
ErikZalm	96a0cdc541	Merge pull request #716 from drf5n/maketeensy ... Makefile: Update for Arduino 1.0.5 and Teensyduino dependent boards (HAR...	2014-01-31 07:04:29 -08:00
whosawhatsis	d24df7af2c	M200 implementation	2014-01-31 00:54:19 -08:00
David Forrest	f0b8d5ba3d	createTemperatureLookupMarlin.py: Change comment to refer to actual program name.	2014-01-29 23:34:22 -05:00
David Forrest	50f44d9249	createTemperatureLookupMarlin.py: Truncate to short after application of OVERSAMPLENR for improved resolution.	2014-01-29 23:24:07 -05:00
David Forrest	f5b5dd8038	createTemperatureLookupMarlin.py: Add output of Steinhart-Hart coefficients.	2014-01-29 22:59:47 -05:00
David Forrest	76cf07c3f7	Configuration.h: Use OVERSAMPLENR in dT_PID definition.	2014-01-21 23:25:51 -05:00
David Forrest	476c7193d8	temperature.cpp: Use OVERSAMPLENR in oversampling calculation.	2014-01-21 16:49:03 -05:00
whosawhatsis	f08bb8bb6a	Previous commit borked.	2014-01-19 22:06:45 -08:00
whosawhatsis	b1f8f492c6	Remove previous_millis_cmd update from extruder runout prevention code ... This seems to defeat the purpose of previous_millis_cmd, preventing the time elapsed from previous_millis_cmd from ever reaching max_inactive_time or stepper_inactive_time while the heat was on.	2014-01-19 19:22:08 -08:00
whosawhatsis	8a5eaa3c9b	Fix crash after home bug ... Fixes a bug in the Extruder Runout Prevention feature that caused the extruder to move back to “current_position” after a move if it was activated while the move was in progress. For long home moves (which are longer than the dimensions of the machine’s working area), this would cause the machine to crash into the far end of its travel after homing. This usually occurred on the Z axis, which could result in damage to the machine if you don’t hit the reset button in time.	2014-01-19 19:11:51 -08:00
David Forrest	61a7256d42	Enable basic ULTRA_LCD screen w/o encoders and menus.	2014-01-17 17:00:47 -05:00
l.lefebvre	fdac8f6cec	Update ConfigurationStore.cpp ... Unable to compile if ENABLE_AUTO_BED_LEVELING is not set (not set by default).	2014-01-17 16:09:58 +01:00
Alex Borro	05932e4458	Add Z Probe Offset to EEPROM and Ultra LCD	2014-01-16 18:13:46 -02:00
David Forrest	7216583b8b	createTemperatureLookupMarlin.py: Add resolution comments and format for Marlin.	2014-01-16 12:40:15 -05:00
David Forrest	e8e0697e48	fastio.h: Add AT90USBxx_TEENSYPP_ASSIGNMENTS for teensyduino/Lincomatic/Printrboard compatibility.	2014-01-16 11:23:29 -05:00
David Forrest	75f39fadfc	Makefile: Update for Arduino 1.0.5 and Teensyduino dependent boards (HARDWARE_MOTHERBOARD=={8,81,82,83,84})	2014-01-16 10:58:35 -05:00
daid	df194f75e1	Added PT100 support for Ultiboard2	2014-01-06 11:20:03 +01:00
daid	380144c20f	Add Ultiboard2 electronics. With PWM current settings. For the few people that have this new board as experiment in their UM-Original.	2014-01-06 11:05:02 +01:00
fsantini	6ae7f7870d	Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into ErikZalm ... Conflicts: Marlin/Configuration.h Marlin/Marlin_main.cpp	2013-12-23 12:20:32 +01:00
Phil Wise	17d6d965dc	Use C++ initialization list ... This is the recommended approach for object initialization. The change doesn't affect binary size (although in theory it could make it smaller).	2013-12-19 21:21:46 +00:00
Joseivaldo Benito Junior	ce8b9c4fc5	Correct missing parameter from last upmerge ... Signed-off-by: Joseivaldo Benito Junior <jrbenito@benito.qsl.br>	2013-12-19 00:50:44 -02:00
Joseivaldo Benito Junior	8e48e24c7f	Update Delta example files ... Signed-off-by: Joseivaldo Benito Junior <jrbenito@benito.qsl.br>	2013-12-18 00:04:36 -02:00
ErikZalm	46d2443c7d	Merge pull request #676 from IVI053/Marlin_v1 ... Minor improvements for encoder configuration, LCD entry for PSU controll and thermistor pins on RAMPS	2013-12-17 02:28:28 -08:00
-	eed053dffb	Revert "Made numbering of heat bed thermistor more logical as D8 is bed, D9 is Extruder 2 and D10 is Extruder 1, so T0 should be E1, T1 E1 and T2 bed to be sequential as MOSFET-Outputs" ... This reverts commit b7eadb9f37.	2013-12-16 12:22:06 +01:00
Erik van der Zalm	8349fc89a4	Fixed planner bug	2013-12-16 11:40:23 +01:00
Francesco Santini	da2a6f9a31	Accurate bed leveling: x loop inside y and zigzag motion	2013-12-13 10:31:19 +01:00
RicardoGA	d29615dc0c	Z and Y dual stepper drivers error ... if you try to enable Z_DUAL_STEPPER_DRIVERS the error "You cannot have dual drivers for both Y and Z" shows even if you don't have defined Y_DUAL_STEPPER_DRIVERS and don't let you compile the firmware to solve this problem i change this line: #ifdef Z_DUAL_STEPPER_DRIVERS && Y_DUAL_STEPPER_DRIVERS to: #if defined (Z_DUAL_STEPPER_DRIVERS) && defined (Y_DUAL_STEPPER_DRIVERS) now the error only show if you define both Z_DUAL_STEPPER_DRIVERS and Y_DUAL_STEPPER_DRIVERS	2013-12-11 14:37:43 -06:00
fsantini	5bde7fcb28	Minor code and comment polishing	2013-12-11 21:27:43 +01:00
-	20faff5935	Incorporate PS_DEFAULT_OFF for starting state on LCD menu entry	2013-12-08 21:35:57 +01:00
-	e5d3044801	Added posibility to set ENCODER_STEPS_PER_MENU_ITEM in Configuration.h like ENCODER_PULSES_PER_STEP as it depends on it for usability	2013-12-08 21:34:56 +01:00
-	b7eadb9f37	Made numbering of heat bed thermistor more logical as D8 is bed, D9 is Extruder 2 and D10 is Extruder 1, so T0 should be E1, T1 E1 and T2 bed to be sequential as MOSFET-Outputs	2013-12-08 21:30:42 +01:00
Michal Dyntar	e8786bf110	Added support for Cheaptronic v1 electronic	2013-12-07 13:29:47 +01:00
fsantini	cc2925b705	Implemented a least squares fit of the bed equation for auto bed leveling. ... The code for the LSQ solver (qr_solve) is copyrighted by John Burkardt and released under LGPL here: http://people.sc.fsu.edu/~%20jburkardt/c_src/qr_solve/qr_solve.html (see qr_solve.cpp for further copyright information)	2013-12-06 21:46:25 +01:00
fsantini	b64661070e	Fixed the plane vector equation to a simpler one (only dependent on the normal) ... Removed the calculation of the inverse matrix since the rotation matrix is orthogonal, therefore inverted == transposed. Much simpler and mathematically robust.	2013-12-06 21:32:21 +01:00
Alex Borro	5c44f6c434	Bed Heater monitoring in Controller Fan ... In some cases the Bed Heater FET heats up more then stepper drivers, so this change add the bed monitoring to the controller fan. As soon as the bed heater is turned on, the controller fan will run as well.	2013-11-27 23:23:06 -02:00
Alex Borro	b33375d438	Z Axis Safe Homing when using Z Probe ... Recommended for those who are using the Z Probe for Z Homing (as Z-Endstop) This feature has two changes: 1) Allow user to choose where the Z Probe will touch the bed when homing all axis together (G28) by setting below defines: Z_SAFE_HOMING_X_POINT Z_SAFE_HOMING_Y_POINT 2) Prevents the user to perform Z Axis Homing when the Z Probe is outsite bed.	2013-11-27 22:37:35 -02:00
Alex Borro	35905ea4f9	Allow heaters to stay full On when PWM=127 ... In previous version, even with PWM = 127, the system turns the FET off and then on in the next cycle. This bevavior may increase the FET heat dissipation. It was fixed keeping the FET always On when PWM=127.	2013-11-27 18:13:38 -02:00
Erik van der Zalm	a94e588765	Changed slow buttons behavior.	2013-11-17 17:41:30 +01:00
Erik van der Zalm	69af392554	Added HEATERS_PARALLEL (Request from reifsnyderb) ... This allows a hot end with two heaters and a FET for each heater. This is useful if the FET is not capable of heating two heaters.	2013-11-17 13:29:02 +01:00
Erik van der Zalm	48a185d004	Fixed compile errors from bad commits.	2013-11-10 16:36:37 +01:00
ErikZalm	24d1f480b6	Merge pull request #647 from shaggythesheep/newfeature-M226 ... Implement M226 - GCode Initiated Pause	2013-11-10 07:27:01 -08:00
ErikZalm	95b41413e6	Merge pull request #641 from hugokernel/master ... M80 - ATX Power On related modification	2013-11-10 07:26:35 -08:00
ErikZalm	59b96e323e	Merge pull request #640 from fmalpartida/SAV-MkI ... Added support for BT on AT90USB devices, corrected LCD bug, added new board and LCD	2013-11-10 07:26:08 -08:00
ErikZalm	2433ee6fc8	Merge pull request #637 from justuswilhelm/Marlin_v1 ... Fix servo control for Melzi v2.0	2013-11-10 07:22:12 -08:00
ErikZalm	3455a2bac2	Merge pull request #636 from PrintToPeer/Marlin_v1 ... Add UUID support to M115 responses.	2013-11-10 07:21:46 -08:00
Richard Miles	dc887ef99b	Implement M226 - GCode Initiated Pause ... Implemented M226 as described here: http://reprap.org/wiki/G-code#M226:_Gcode_Initiated_Pause Waits for pin to be become either HIGH, LOW or the inverse of what it was before. Allows printing to pause until user interaction	2013-11-09 15:11:58 +00:00
Charles R	c244eb860c	If you have a switch on suicide pin, this is useful if you want to ... start another print with suicide feature after a print without suicide...	2013-11-04 12:04:04 +01:00
fmalpartida	7b556d2e96	Added BT support on AT90USB devices ... Added AT90USB device BT connectivity support using second UART.	2013-11-03 19:57:06 +01:00
Kaz Walker	a5e8575829	Add UUID support to M115 responses.	2013-11-01 14:51:50 -06:00
Daniel Benamy	cab84e0e5b	Add (correct) missing pin definitions for Y2 ... I tested this and it works.	2013-10-30 22:44:20 -04:00
fmalpartida	5b3f60ea2e	Corrected LCD only error ... If only an LCD is defined and no menu or keyboard defined, there is a compilation error. Added conditional compilation.	2013-10-30 21:52:46 +01:00
Justus Perlwitz	62d0b79023	Fix servo control for Melzi	2013-10-30 20:59:58 +01:00
fmalpartida	b5a964fcc5	Initial SAV MkI (RepRap CloneWars board) integration. ... Included support for BT dongle on AT90USB boards. Added LCD Shift Register LCD control Included support for RepRap Clone Wars project board (SAV MKI).	2013-10-30 11:45:32 +01:00
dumle29	f941203172	PS_ON configurable boot state ... Allows the user to select wheter or not the PSU should be turned on or kept in standby when marlin boots	2013-10-29 18:44:56 +01:00
whosawhatsis	c79e3967b3	Make G11 not horribly broken	2013-10-24 18:58:42 -07:00
bkubicek	d69822ed51	Fix '#' ... since it can occure in comments.	2013-10-22 10:34:51 +02:00
bkubicek	2fb2a0a119	Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1	2013-10-22 10:08:21 +02:00
bkubicek	39d88bcccb	preparation for hibernation ... If a print is stopped, it would be nice in the future to write a file with the printer state, the filename of the print, and the position within the print. this file could be read, to continue a previously stopped print. not finished yet.	2013-10-22 10:04:08 +02:00
bkubicek	ab965376ff	Sub-file calls. ... by overloading M32 it is now possible to execute gcode files from other gcode files, with a fixed recursion level. This can be used e.g. for having a real start.g and end.g somewhere on the sd card, which are then called from the normal print file. Another usecase would be to have macro-files for nozzle-change and layerchange. I have not tested the speedwise performance. The testing was done with pronterface. syntax: normal call from sd card will open the new file and continue executing there. M32 !/path/filename# this however will call the new file and return to the caller file. M32 P !/path/filename# with the optional "S<position>" the file starting position can be set. this is for continuing prints from a previous location.	2013-10-22 10:02:18 +02:00
bkubicek	b2cc27e5ea	Added a magic character for sd buffering. ... if a '#' is read now the buffer will be emptied before reading ahead. This is so one can execute files from within gcode files, without messing the buffer with preread characters from the caller file. # can not occure in sd files imho, because it should only occure within checksums in ther serial communication. Yes, thats a lame argument. If you have a better idea please tell me. It has to be a character that one can type on a keyboard manually.	2013-10-22 09:54:13 +02:00
Erik van der Zalm	8a08cca0f2	Added temperature status less. ... Hopefully fixed viky button handling without braking other boards	2013-10-20 12:12:35 +02:00
Erik van der Zalm	667d278f54	Revert "Fix for Viki display" ... This reverts commit 314fd13c39.	2013-10-20 10:16:46 +02:00
Erik van der Zalm	bf27e79e74	Small BlinkM fix	2013-10-20 10:06:02 +02:00
Erik van der Zalm	87e28c0599	Added ifdefs to blinkm	2013-10-20 09:55:15 +02:00
Erik van der Zalm	24c6b2ab35	Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1	2013-10-20 09:51:58 +02:00
ErikZalm	6a803ba9c5	Merge pull request #590 from timkoster/Marlin_v1 ... Added BlinkM support over i2c	2013-10-20 00:51:35 -07:00
Erik van der Zalm	457d8a0acb	Fixed merge conflicts	2013-10-20 09:50:27 +02:00
Alex Borro	6f85a8c7aa	Bed auto Leveling change: Raise Z before homing ... - Added "Z_RAISE_BEFORE_HOMING" for raising Z the defined distance before homing. This is useful to avoid Z-Probe collision when hotend is near bed. - Fixed the issue of Z not going bellow Z_PROBE_OFFSET when "min_software_endstops" is true. Now the Z_PROBE_OFFSET is not set in Z_MIN_POS, it is added after homing.	2013-10-12 17:28:11 -03:00
Alex Borro	dd3086d3f2	Show Temperature ADC values ... If "SHOW_TEMP_ADC_VALUES" is defined in Configuration_adv.h, the M105 command will present, after tradicional temperatures, the ADC value read from temp sensors. This is great for adjusting thermistor tables with thermocouple. From Pronterface you can see the ADC value and compare with a thermocouple reading.. then you just need to create your own thermistor table. Since this merge doesnt change the original information, it doesnt mess with PC software parsing (tested under Pronterface and Repetier-Host).	2013-10-12 10:41:23 -03:00
bkubicek	7fad13a1e2	Reverse SD card file name order. ... This is _not_ automatically the cronological, since deleting a file will free the filesystem descriptor for it, which then will be used by the next file copied on it. Since this makes the auto0.g file very inaccessible, I put the option back, to have it in the prepare menu. this should satisfy https://github.com/ErikZalm/Marlin/pull/373 as a reminder, auto0.g will be executed every time after a boot with sd card present and file present. thereafter, if there is a file auto1.g this will be done. Thats IMHO the best place to put settings, and prepare heating. I also execute again after each (now again via the prepare menu) before starting a new print/ after a failed one. It for me 100% replaces any start.gcode form the slicers.	2013-10-12 13:24:55 +02:00
bkubicek	b832f5b9f6	added delta tower babystepping. Its untested, but hopefully florian horsch will be able to try. ... also, removed some trouble for compilation with corexy. I think that babystepping is only possible in z for a delta tower. not sure if it would be usefull to step individual motors on a delta, i don't own one	2013-10-07 09:14:04 +02:00
bkubicek	c38b0855c8	I think that filament change is ready for the masses. I have tested very often with my ultimaker. ... I strongly vote for it being a single gcode, because otherwise the triggering from the menu is terrible.	2013-10-06 21:20:26 +02:00
bkubicek	d147a057ac	Add the socalled "Babystepping" feature. ... It is a realtime control over the head position via the LCD menu system that works _while_ printing. Using it, one can e.g. tune the z-position in realtime, while printing the first layer. Also, lost steps can be manually added/removed, but thats not the prime feature. Stuff is placed into the Tune->Babystep * It is not possible to have realtime control via gcode sending due to the buffering, so I did not include a gcode yet. However, it could be added, but it movements will not be realtime then. Historically, a very similar thing was implemented for the "Kaamermaker" project, while Joris was babysitting his offspring, hence the name. say goodby to fuddling around with the z-axis.	2013-10-06 21:14:51 +02:00
Erik van der Zalm	bca353cc12	Fixed duplicate define in fastio.h	2013-10-03 19:24:53 +02:00
Alex Borro	253dfc4bc1	Bed Auto Leveling feature ... Check the Readme for instruction how to enable and configure the feature	2013-09-29 13:20:06 -03:00
ErikZalm	1bda6bf862	Merge pull request #609 from phq1910/patch-1 ... Update Configuration.h	2013-09-26 11:47:58 -07:00
ErikZalm	c80aac1518	Merge pull request #610 from phq1910/patch-2 ... Update pins.h	2013-09-26 11:47:47 -07:00
Erik van der Zalm	314fd13c39	Fix for Viki display	2013-09-26 20:32:19 +02:00
phq1910	4f7c6dfe35	Update pins.h ... Include Pins cpu Sethi 3D	2013-09-26 11:40:54 -03:00
phq1910	57173739a1	Update Configuration.h ... Include CPU Sethi 3D	2013-09-26 11:29:44 -03:00
Erik van der Zalm	0dca49a7c0	Added Azteeg X3 board.	2013-09-24 17:31:16 +02:00
Erik van der Zalm	d8c2c810b4	Added info to the delta configuration files in the configuration.h file	2013-09-23 23:29:46 +02:00
Erik van der Zalm	9bc88f8bab	Placed optional ENCODER_PULSES_PER_STEP in the configuration.h file	2013-09-23 23:25:11 +02:00
Erik van der Zalm	3ca1ca6869	Fixed missing ENCODER_PULSES_PER_STEP	2013-09-23 23:18:35 +02:00
Tim Koster	97b0da0c2e	Removed #ifndef BLINKM	2013-09-22 10:43:27 +03:00
Tim Koster	61db046b32	Added #ifdef BLINKM around new code. Also refined BlinkM.h.	2013-09-20 10:57:42 +03:00
Richard Miles	77df2ab0e7	Make Y_DUAL_STEPPER_DRIVERS disabled by default	2013-09-17 21:49:44 +01:00
Richard Miles	ed1ab42186	Added Y_DUAL_STEPPER_DRIVERS ... Enables two stepper drivers to be used for the Y axis (useful for Shapeoko style machines) Each Y driver can be stepped in either the same way or in opposite directions, accounting for different hardware setups (leadscrew vs. belt driven)	2013-09-17 19:19:20 +01:00
Richard Miles	f4a59e4ce5	Revert "Added Y_DUAL_STEPPER_DRIVERS" ... This reverts commit 7ee275b620.	2013-09-17 19:05:49 +01:00
Richard Miles	7ee275b620	Added Y_DUAL_STEPPER_DRIVERS ... Enables two stepper drivers to be used for the Y axis (useful for Shapeoko style machines) Each Y driver can be stepped either the same way or in opposite directions, accounting for different hardware setups (leadscrew vs. belt driven)	2013-09-17 19:02:00 +01:00
ErikZalm	6a1e980c6d	Merge pull request #600 from xoan/Encoder_Pulses_Per_Step ... add ENCODER_PULSES_PER_STEP	2013-09-14 04:56:45 -07:00
ErikZalm	20076a8bd3	Merge pull request #598 from GDV0/Marlin_v1 ... FIx compilation error when enabling SERVO_ENDSTOPS (#591)	2013-09-14 04:54:19 -07:00
Erik van der Zalm	3626b5ad8b	Removed Delta from the default config file. ... Changed EEPROM CHITCHAT behavior. M503 is always enabled.	2013-09-14 13:50:09 +02:00
Xoan Sampaiño	bf7007d02f	add ENCODER_PULSES_PER_STEP	2013-09-13 04:12:51 +02:00
GDV0	f17506c504	FIx compilation error when enabling SERVO_ENDSTOPS (#591)	2013-09-11 23:09:37 +02:00
Martin Lukasik	acd8619809	Fan fix for Panelolu2+Sanguinololu.	2013-09-10 22:10:58 +01:00
George Roberts	595580556c	Fixed bug that makes ulticontroller knob backwards introduced Feb 28 2013 by Robert. ... Bug introduced in version 6beb42cdf6. Robert did a good job of simplifying but messed up this chunk of code. Looking at working version: 839bef6d5d it seems there is no case where encrot3 should be defined as 2 because if ULTICONTROLLER is defined then NEWPANEL is also defined.	2013-09-10 09:56:19 -04:00
Tim Koster	88dfeefca3	Define BlinkM default disabled	2013-09-10 12:32:21 +03:00
Tim Koster	5350faf2a2	Merge https://github.com/timkoster/MarlinBlinkM into Marlin_v1	2013-09-10 12:27:26 +03:00
Tim Koster	7016cc9511	Added BlinkM support over i2c	2013-09-10 12:18:29 +03:00
Tim Koster	3b315b3da0	Added BlinkM support over i2c	2013-09-06 22:25:39 +03:00
Jim Morris	f26f26b7bd	Fix the example delta configuration as someone forgot to do it.	2013-09-05 16:36:55 -07:00
Peter Hercek	9aa2229077	add command M666 for adjusting delta printer endstop position	2013-08-28 01:15:20 +02:00
Robert F-C	9547fb9dfb	Add duplication and auto-park mode for dual x-carriage support.	2013-08-08 00:10:26 +10:00
Steve Kelly	53614e5144	add pins for rambo lcd	2013-08-03 11:45:53 -05:00
Steve Kelly	b42d24e31e	add additional pins to avr2560 for rambo lcd	2013-08-03 11:37:12 -05:00
Nicolas Rossi	b0c8120fcc	Added feedrate setting in exemple config for manual moves from panel	2013-08-03 13:09:53 +02:00
Nicolas Rossi	a54fe2d73c	Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin.git into Marlin_v1 ... Conflicts: Marlin/Marlin_main.cpp	2013-08-03 13:05:56 +02:00
ErikZalm	7ea63d08df	Merge pull request #565 from iXce/avrdudeconfpath ... Detect OS in Makefile to use the correct avrdude.conf path	2013-08-02 13:16:07 -07:00
ErikZalm	4187b637a5	Merge pull request #570 from hg42/separate-INVERTING-macros-for-MIN-and-MAX-endstops ... separate INVERTING for MIN and MAX endstops (6 #defines instead of 3)	2013-08-02 13:15:30 -07:00
ErikZalm	07e7de3600	Merge pull request #569 from hg42/convert-PROTOCOL-macros-from-statements-to-expressions ... convert PROTOCOL macros from statements to (multiple, comma separated) expressions	2013-08-02 13:13:29 -07:00
Guillaume Seguin	c0c4c97db6	Detect OS in Makefile to use the correct avrdude.conf path	2013-08-01 19:20:27 +02:00
hg42@gmx.net	2ca983568d	separate INVERTING for MIN and MAX endstops (6 #defines instead of 3)	2013-08-01 15:06:39 +02:00
hg42@gmx.net	3700f688f5	convert PROTOCOL macros from statements to (multiple, comma separated) expressions	2013-08-01 14:56:39 +02:00
daid	a504c88346	Fix a bug where the PID controllers D action kicks in hard as soon as the PID controller starts.	2013-08-01 14:12:30 +02:00
Nicolas Rossi	394ed08f88	Added feedrate setting for manual moves from panel	2013-07-30 14:33:30 +02:00
Nicolas Rossi	9bf1cf1b22	Pre-calculate diagonal rod length squared	2013-07-30 14:09:21 +02:00
Nicolas Rossi	4623e78ce0	Added Honeywell thermistor 135-104LAF-J01	2013-07-30 14:02:18 +02:00
Brendan-csel	d7f384f680	Skip SD menu refresh if nothing has changed	2013-07-30 14:02:15 +02:00
Brendan-csel	abc8320a68	Save LCD_CLICKED before it is cleared ... The SD card menu was refreshing so slowly that the button interrupt was clearing LCD_CLICKED before the menu items could check it.	2013-07-30 14:02:13 +02:00
Guillaume Seguin	f4c3135c6d	Add Panelolu2 pins for RAMPS1.3	2013-07-30 14:02:11 +02:00
Guillaume Seguin	aae42c68f9	Update French translation in language.h	2013-07-30 14:02:08 +02:00
Guillaume Seguin	4d435c38a6	Add support of LiquidTWI2-based panels to Makefile ... Use LIQUID_TWI2=1 as make argument to enable this support	2013-07-30 14:02:06 +02:00
Guillaume Seguin	6c42a3a339	Woops, fix logic	2013-07-30 14:02:04 +02:00
Guillaume Seguin	376d8af2c8	Report temperatures for all extruders	2013-07-30 14:02:01 +02:00
ErikZalm	434b6a05c1	Merge pull request #552 from iXce/Marlin_v1 ... Report temperatures for all extruders in reply to M105	2013-07-29 10:39:21 -07:00
ErikZalm	bdc2621119	Merge pull request #561 from Brendan-csel/Marlin_v1 ... Fix for Viki LCD issues printing from SD card	2013-07-29 10:38:17 -07:00
ErikZalm	6965bd4e15	Merge pull request #560 from njprossi/Marlin_v1 ... Fixed move from panel for delta bot #557	2013-07-29 10:37:40 -07:00
ErikZalm	a55b33e613	Merge pull request #559 from iXce/panelolupinsramps13 ... Add Panelolu2 pins for RAMPS1.3	2013-07-29 10:37:03 -07:00
ErikZalm	8b34351537	Merge pull request #558 from iXce/frenchupdate ... Update French translation in language.h	2013-07-29 10:36:43 -07:00
ErikZalm	735e556724	Merge pull request #555 from iXce/liquidtwi2_makefile ... Add support of LiquidTWI2-based panels to Makefile	2013-07-29 10:33:54 -07:00
Brendan-csel	d80aecda0a	Skip SD menu refresh if nothing has changed	2013-07-29 21:00:29 +12:00
Brendan-csel	be2dea1dc6	Save LCD_CLICKED before it is cleared ... The SD card menu was refreshing so slowly that the button interrupt was clearing LCD_CLICKED before the menu items could check it.	2013-07-29 20:58:09 +12:00
Nicolas Rossi	55c287a69e	Fixed move from panel for delta bot #557	2013-07-28 22:54:37 +02:00
Guillaume Seguin	1902d339b0	Add Panelolu2 pins for RAMPS1.3	2013-07-28 19:19:57 +02:00
Guillaume Seguin	eb23a68e92	Update French translation in language.h	2013-07-28 18:50:47 +02:00
ErikZalm	1561c6df51	Merge pull request #547 from wolfmanjm/delta-configuration ... Setup Default configuration for Deltas if DELTA is defined	2013-07-24 03:11:36 -07:00
Guillaume Seguin	374bc99fa3	Add support of LiquidTWI2-based panels to Makefile ... Use LIQUID_TWI2=1 as make argument to enable this support	2013-07-24 12:09:53 +02:00
Jim Morris	ab624eac2a	revert COnfiguratiuon to the same as head	2013-07-24 02:57:46 -07:00
Jim Morris	52f79ffeca	add an example default configuration for delta style bots	2013-07-24 02:55:52 -07:00
Jim Morris	b9d7ccf1cd	Merge remote-tracking branch 'upstream/Marlin_v1' into delta-configuration ... Conflicts: Marlin/Marlin_main.cpp	2013-07-24 02:49:25 -07:00
Guillaume Seguin	d4d1540727	Use -fno-use-cxa-atexit to override gcc --enable-cxa_atexit	2013-07-24 11:19:38 +02:00
Guillaume Seguin	01ed99143c	Woops, fix logic	2013-07-23 23:34:42 +02:00
Guillaume Seguin	76841450c8	Only display poweron/poweroff if PS_ON_PIN > -1	2013-07-23 22:28:30 +02:00
Guillaume Seguin	44f327d738	Uniformly reindent language.h	2013-07-23 22:13:40 +02:00
Guillaume Seguin	326d2db025	Update language.h so that all languages compile ... Some strings still need translation, but at least everything compiles.	2013-07-23 22:11:54 +02:00
Guillaume Seguin	2cb716f513	Run Marlin/language.h through dos2unix	2013-07-23 21:49:37 +02:00
Guillaume Seguin	34da3a0a3f	Merge github.com:ErikZalm/Marlin into Marlin_v1 ... Conflicts: Marlin/language.h	2013-07-23 21:46:41 +02:00
Guillaume Seguin	18199ff960	Merge github.com:ErikZalm/Marlin into Marlin_v1	2013-07-23 21:33:52 +02:00
Robert F-C	fb5334f428	Fixed compile error when QUICK_HOME is defined. ... As well a couple of minor changes to handling of extruder offset for dual x-carriage mode.	2013-07-22 22:46:14 +10:00
Robert F-C	c3568398b5	Disable DUAL_X_CARRIAGE by default	2013-07-20 23:50:30 +10:00
Robert F-C	39cd3dbdbe	Remove dual x-carriage functionality that could/should be implemented in slicer ... Also added a couple of missed merge lines in homeaxis() from previous commit.	2013-07-20 13:07:50 +10:00
Jim Morris	fb20ceabce	enable soft endstops for delta ... disable delta by default	2013-07-17 16:21:51 -07:00
Jim Morris	d01ee7e7b5	fix zjerk being the same for delta as xy jerk ... add more delta defaults on delta make second home even slower	2013-07-17 16:14:07 -07:00
Robert F-C	d7390e13d9	Support dual x-carriage printers ... Dual x-carriage designs offer some substantial improvements for dual extruder printing.	2013-07-17 22:44:45 +10:00
Jim Morris	f3aa2a48e7	update max pos	2013-07-17 01:29:51 -07:00
Jim Morris	460751503e	Added default configurations for deltas when DELTA is defined	2013-07-17 01:17:27 -07:00
Maik Stohn	9da94c247a	fixed bad lcd commit from makr3d ... #elsif does not exist #elif is correct	2013-07-15 17:34:21 +02:00
Erik van der Zalm	59004023fd	Fixed typo	2013-07-15 17:22:56 +02:00
Erik van der Zalm	461dad6e05	Added : M32 - Select file and start SD print (Can be used when printing from SD card) ... Untested	2013-07-14 22:39:59 +02:00
Erik van der Zalm	c4a2077951	M109 and M190 now wait when cooling down if R is used instead of S. ... M109 S180 waits only when heating. M109 R180 also waits when cooling.	2013-07-14 21:10:24 +02:00
ErikZalm	8a2a3ef91d	Merge pull request #531 from iXce/Marlin_v1_lcd ... Only clamp panel movements if software endstops are enabled	2013-07-14 06:50:23 -07:00
Erik van der Zalm	6397b3339c	restored configuration.h defaults	2013-07-14 15:49:03 +02:00
Erik van der Zalm	cdaaad3df1	Merge branch 'Marlin_v1' of https://github.com/makr3d/Marlin into makr3d-Marlin_v1	2013-07-14 15:45:49 +02:00
Erik van der Zalm	e3bdefd873	fixed missing #endif	2013-07-14 15:42:53 +02:00
Erik van der Zalm	a5be0c52c6	no message	2013-07-14 15:35:54 +02:00
Michael Mayer	e509cdbeb0	added contrast control function for gLCDs	2013-07-14 15:28:26 +07:00
Michael Mayer	99b7e926e7	added MaKr3d Melzi board	2013-07-14 15:17:55 +07:00
Gabino Lopez	68be33b1fc	Update language.h ... I update the spanish Messages, now this compile for spanish language.	2013-07-04 10:23:00 +02:00
daid	acb3271c9a	Merge pull request #534 from xifle/Marlin_v1 ... Fixes compiler warning for feedrate deadzone	2013-07-01 23:41:51 -07:00
xifle	61fe430d4f	Should fix compiler warning for feedrate deadzone	2013-07-01 11:10:02 +02:00
Gord Christmas	fde17d5720	Fix for ugly code compilation errors in SERVO_ENDSTOP checks	2013-06-28 08:02:04 -07:00
Guillaume Seguin	aa65c20d1f	Only clamp panel movements if software endstops are enabled	2013-06-28 14:18:00 +02:00
Erik van der Zalm	ecf3ab5de4	Added thermistor 60 to configuration.h	2013-06-27 23:25:51 +02:00
Nicolas Rossi	2daa85918e	Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin.git into Marlin_v1 ... Conflicts: Marlin/Configuration.h Marlin/Marlin_main.cpp Marlin/language.h Marlin/pins.h Marlin/ultralcd.cpp	2013-06-20 23:59:56 +02:00
Erik van der Zalm	2015989f84	Added DISABLE_MIN_ENDSTOPS	2013-06-18 19:20:26 +02:00
Christian Inci	648d45cfb2	Fix Pin Description Typo ... Reverse 'Bed' and 'Fan' at the RAMPS 33 Description. Signed-off-by: Christian Inci <chris.pcguy.inci@gmail.com>	2013-06-16 23:35:33 +02:00
ErikZalm	171719f18c	Merge pull request #525 from lajos/ultralcd_pid ... ultralcd.cpp compile errors when !defined(PIDTEMP)	2013-06-16 00:02:54 -07:00
lajos	b519af4f05	fixed another !defined(PIDTEMP) compile in ultralcd.cpp	2013-06-15 20:49:18 -04:00
lajos	7d03c52511	fixed compile error in ultralcd.cpp when PIDTEMP undefined	2013-06-15 18:09:52 -04:00
lajos	02dee80fa5	added Azteeg X1 motherboard	2013-06-15 16:58:17 -04:00
Henrik Brix Andersen	47dc70e3ec	Fix location of avrdude.conf	2013-06-15 09:50:25 +02:00
Henrik Brix Andersen	1d258903bb	Allow command line compilation when using BEEPER.	2013-06-15 09:36:55 +02:00
Erik van der Zalm	e34c9981ab	Delta disabled by default	2013-06-11 22:33:58 +02:00
Erik van der Zalm	26a441fc7d	More 3Drag controller patches.	2013-06-10 18:26:15 +02:00
Erik van der Zalm	ac975ed8c2	Merge branch 'deltabot' into Marlin_v1	2013-06-10 18:20:29 +02:00
Jim Morris	caa848f943	fix homing for deltas	2013-06-09 21:10:00 -07:00
Erik van der Zalm	7ad12be763	Merge branch 'Marlin_v1' of https://github.com/codexmas/Marlin into codexmas-Marlin_v1 ... Conflicts: Marlin/Configuration.h README.md	2013-06-09 23:10:41 +02:00
Erik van der Zalm	408169aef4	Merge branch 'Marlin_v1' of https://github.com/BorisLandoni/Marlin into BorisLandoni-Marlin_v1 ... Conflicts: Marlin/Configuration.h Marlin/language.h Marlin/pins.h	2013-06-09 22:57:40 +02:00
Erik van der Zalm	bd96d22bfb	Merge branch 'Marlin_v1' into thinkyhead ... Conflicts: Marlin/Configuration.h Marlin/Configuration_adv.h Marlin/Marlin.h Marlin/Marlin_main.cpp Marlin/Servo.cpp Marlin/language.h Marlin/pins.h Marlin/planner.cpp Marlin/ultralcd_implementation_hitachi_HD44780.h README.md	2013-06-09 22:26:47 +02:00
Erik van der Zalm	73f21cd5d6	Spanish updated so far.	2013-06-09 21:40:35 +02:00
Erik van der Zalm	6f4a6e531c	Merge branch 'deltabot' into Marlin_v1	2013-06-09 13:55:18 +02:00
Erik van der Zalm	01edf22a10	Fix home_all_axis to make QUICK_HOME work with Repetier-Host which sends G28 X0 Y0 Z0 instead of G28. Thanks to Matt Schoenholz for reporting this issue.	2013-06-09 13:54:19 +02:00
Erik van der Zalm	ff6fa09ecf	Moved corexy implementation from stepper to planner ... (Thanks iquizzle)	2013-06-09 13:10:06 +02:00
Erik van der Zalm	c8dcc7c208	Allow increasing the software PWM frequency.	2013-06-09 12:52:49 +02:00
Erik van der Zalm	8b0d82e9db	Removed "awaiting translation" for french	2013-06-09 12:24:06 +02:00
Erik van der Zalm	1e05d192ab	Make the beep tone less offensive	2013-06-09 12:21:16 +02:00
Erik van der Zalm	373f3ecab3	Merge branch 'deltabot' of https://github.com/jcrocholl/Marlin into deltabot ... Conflicts: Marlin/Configuration.h Marlin/Marlin_main.cpp Marlin/pins.h	2013-06-09 00:51:58 +02:00
kiyoshigawa	f295712008	Trying to fix weird diff on ultralcd_implementation_hitachi_HD44780.h	2013-06-08 09:27:56 -06:00
kiyoshigawa	69b02031ca	Fixed small error in lcd define statements.	2013-06-08 09:09:11 -06:00
kiyoshigawa	6a81291c57	Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1 ... This should fix issues with pull request 467, I hope. Conflicts: Marlin/Configuration.h Marlin/Marlin.pde Marlin/ultralcd_implementation_hitachi_HD44780.h	2013-06-08 08:48:18 -06:00
BorisLandoni	c1cb5977ee	Update Configuration.h	2013-06-08 14:37:39 +02:00
BorisLandoni	8a5bd8a808	Update Configuration.h	2013-06-08 14:37:17 +02:00
BorisLandoni	c1d7cf939e	Update language.h	2013-06-07 17:38:17 +02:00
BorisLandoni	4c7d1436e9	Update pins.h	2013-06-07 18:37:44 +03:00
BorisLandoni	6588933c04	Update Configuration.h	2013-06-07 18:36:16 +03:00
Scott Lahteine	5dabc95409	Apply all changes from latest Marlin_V1 ... Diffed and merged, preserving my updates	2013-06-06 15:49:25 -07:00
Gord Christmas	a733537ddd	Missed some variable declarations ... Integrated fixes from henrikbrixandersen pull request #504	2013-06-06 09:18:03 -07:00
Gord Christmas	f4f30c9d64	Added servo actuated enstop coding to allow G28 command to engage and retract a servo to specified angles.	2013-06-06 07:36:52 -07:00
Erik van der Zalm	79374f0b93	Merge branch 'reisnyderb' of https://github.com/ErikZalm/Marlin into Marlin_v1	2013-06-05 17:44:48 +02:00
Maik Stohn	da05b3ba94	faster GLCD (ST7920 SW-SPI) implementation / fixes ... - fixed long menu entries (>14 or >18 chars) caused overrun in dogm lcd implementation - fixed pin set problem when in interrupt - much faster ST7920 SW-SPI implementation - increased ST7920 framebuffer size for more speed	2013-06-05 16:27:44 +02:00
kiyoshigawa	4b19c8552e	Fixing changed Configuration.h settings to be default values per ErikZalm Request.	2013-06-04 12:01:55 -06:00
Erik van der Zalm	971ec35135	Expanded M302 to allow setting the temp	2013-06-02 17:36:23 +02:00
Erik van der Zalm	5090c56651	More redundant temp sensor changes. (After testing and debugging by reifsnderb)	2013-05-29 19:29:30 +02:00
Guillaume Seguin	16b9239a26	Report temperatures for all extruders	2013-05-29 18:06:12 +02:00
ErikZalm	a964b3cf3d	Merge pull request #495 from Gatulibu/Marlin_v1 ... Added support for Megatronics v2.0 and Minitronics v1.0	2013-05-28 07:51:49 -07:00
Maik Stohn	e8572c5239	Fix: Long menu entries (>14 or >18 chars) caused overrun in hitachi display implementation	2013-05-28 15:53:07 +02:00
Maik Stohn	7ee70c2248	Fix: removed wrong ; at end of define	2013-05-28 15:50:48 +02:00
Gatulibu	b78fa6bb70	Added support for Megatronics v2.0 and Minitronics v1.0 ... merged from code downloaded from reprapworld.com	2013-05-28 14:03:31 +02:00
Erik van der Zalm	9be61cdc02	Added redundant temp sensor	2013-05-26 17:57:49 +02:00
Erik van der Zalm	7231a20dba	Put #ifdef around servo pins in pins.h. This allows the pins to be used for M42.	2013-05-24 21:05:11 +02:00
Alexander Kasimir	e2ff536b03	Fixed typo in Comment	2013-05-22 16:02:03 +03:00
Robert F-C	40eb07bad4	Revert and extend previous change pin check change ... Reviert previous change of #if BLAH_PIN > 0 to #if defined(BLAH_PIN) && BLAH_PIN > -1. Unfortunately some times pin 0 is used. For my sins I've gone through and replaced all unsafe checks of #if BLAH_PIN > -1 with the safe version.	2013-05-22 21:33:23 +10:00
Maik Stohn	bd33cf4a9f	fixed typo / added "const" to defines for newer gcc compatibility	2013-05-21 17:58:34 +02:00
ErikZalm	567291e734	Merge pull request #485 from Banjer/Panelolu2_Melzi ... Add Panelolu2 support for Melzi	2013-05-21 08:46:27 -07:00
Maik Stohn	8d80cbbf4c	fix broken LCD commit #dfa549f268 from buildrob - GLCD/DOGM implementation was ignored	2013-05-21 16:53:38 +02:00
xifle	98d0d48191	fixed merge	2013-05-20 14:52:35 +02:00
xifle	bbe67fca5a	soft tab correction	2013-05-20 14:50:39 +02:00
xifle	9eeb711c96	Merged from Upstream Master	2013-05-20 14:45:37 +02:00
Bas Spaans	424101110c	Add Panelolu2 support for Melzi	2013-05-19 12:09:34 +02:00
Robert F-C	0d4a9444c4	Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1	2013-05-19 08:50:58 +10:00
Erik van der Zalm	86cce025f4	Added #ifdef NUM_SERVOS to servo.cpp	2013-05-18 23:12:28 +02:00
xifle	03141a5ef4	LCD: Added Deadzone at 100% Feedrate ... This adds a deadzone at 100% Feedrate when changing it at the status screen/main menu. Prevents from unwanted feedrate-changing when navigating back to the main menu and makes it easier to return to 100%.	2013-05-18 19:53:46 +02:00
Gord Christmas	28ada096e2	Adding servo documentation	2013-05-18 06:01:58 -07:00
Robert F-C	4121311b9d	Change to LCD status indicators ... The I2C LCD status indicators now indicate when the hotends or bed are turned on at all (rather than just when they are in their heating phase)	2013-05-18 22:30:42 +10:00
Robert F-C	dfa549f268	Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1	2013-05-18 21:59:39 +10:00
ErikZalm	64360164ad	Merge pull request #482 from codexmas/Marlin_v1 ... servosupport	2013-05-16 10:19:00 -07:00
ErikZalm	86405cdd11	Merge pull request #479 from MStohn/thermocouple ... BUGFIXES for temperature.cpp / add RUMBA thermocouple support	2013-05-16 10:06:59 -07:00
Erik van der Zalm	6c45c3f4e7	BariCUDA changes	2013-05-16 19:01:12 +02:00
Gord Christmas	96624f0f31	Forgot to include reference to Servo in makefile	2013-05-16 08:25:20 -07:00
Gord Christmas	dc59f07d24	First attempt at refactoring of original servo code. Only adding servo support as a start to keep things simple.	2013-05-16 07:03:01 -07:00
Gord Christmas	b668cb0516	Adding in clean copies of Servo library from Arduino 1.0.4	2013-05-16 06:47:42 -07:00
MaikStohn	95dff34b73	fixed wrong compare for min temp check of heater 1 and heater 2	2013-05-16 01:17:38 +02:00
MaikStohn	4cc6f9f6de	fixed wrong pin initialization when using temperature 2 pin input	2013-05-16 01:17:08 +02:00
MaikStohn	61a48cc662	Add support for RUMBA thermocouple add on	2013-05-16 01:16:33 +02:00
MaikStohn	9cc15876be	Add support for RUMBA thermocouple add on	2013-05-16 01:16:08 +02:00
ErikZalm	c9cf2174dd	Merge pull request #474 from xifle/Marlin_v1 ... Fixed "Cooldown" Selection not reseting bed temp	2013-05-14 14:58:53 -07:00
Erik van der Zalm	bd2cd4903e	Added #ifdef BARICUDA around the BariCUDA changes	2013-05-14 23:56:32 +02:00
Jordan Miller	37f3199df3	fixed problems in planner with solenoids for BariCUDA when set to 0	2013-05-14 23:35:01 +02:00
Jordan Miller	fbd899a37d	Support for BariCUDA Paste Extruder derived from MakerBot Frostruder. Using Ultimachine RAMBo board. M126/M127 and M128/M129.	2013-05-14 23:34:45 +02:00
xifle	29bb8d7d4f	Fixed "Cooldown" Selection not reseting bed temp ... - enquecommand with multiple lines "\n" doesn't work -> M140 S0 didn't get processed. So I wrote a new func for the cooldown which uses setTargetHotend. In addition this does return to status page after selection. - Added setWatch() to preheat-functions (Temperatur sanity check would never have worked when preheating from the lcd panel)	2013-05-14 16:56:19 +02:00
Robert F-C	015d0594b0	Optimize menu selection for Viki rotary encoder. ... The Viki LCD rotary encoder uses a different number of steps per rotation. This fixes the seeming "missed" steps when selecting a menu.	2013-05-12 07:51:28 +10:00
gregor	2739c26c4f	changes: ... - changed the variables from keypad to reprapworld_keypad - added a missing ifdef check	2013-05-10 22:20:02 +02:00
gregor	6fb9573157	added support for the reprapworld keypad	2013-05-10 21:57:17 +02:00
Tim Anderson	594193c908	Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1	2013-05-06 23:29:38 -06:00
Tim Anderson	1fa61c297e	Turning off Control Panel by Default and Updating the link to the LiquidCrystal_I2C library to avoid confusion.	2013-05-06 23:23:54 -06:00
kiyoshigawa	b27a59f41e	Added support for Elefu RA Board and Elefu Control Panel	2013-05-06 08:44:38 -06:00
midopple	a65a26d6b4	If CORE_XY is in use X and Y Axis had to be activated at the same time	2013-05-05 19:23:59 +02:00
midopple	db2f157a22	Replace the <= to < in the Command M907, M350 and M351. ... The for loop for Axis count over the Array. Add a break after M907	2013-05-05 19:19:55 +02:00
Scott Lahteine	a5cd582665	Support for 10 level deep SD folder hierarchy	2013-05-04 04:18:02 -07:00
Arnoud	fc4ab05157	Solved minor bug in controllerFan() ... Extruder 2 was checked where extruder 1 should be checked.	2013-05-03 21:32:34 +02:00
Scott Lahteine	0ef54f2f85	Make M303 silent when "S0" is sent ... If S is left out perhaps it should be silent, but check the spec for this M code.	2013-05-02 09:55:15 -07:00
Scott Lahteine	a200521eab	Added CUSTOM_MENDEL_NAME option to Configuration.h and language.h ... Also cosmetic comment changes and spelling corrections in printed messages	2013-05-02 09:22:58 -07:00
Martin Renold	1a397825f9	fix DEFAULT_AXIS_STEPS_PER_UNIT minor Z rounding error	2013-05-01 08:30:24 +02:00
Robert F-C	289c02eda4	Remove unnecessary pin initialization in stepper.cpp ... (duplicates initialization in Marlin_main.cpp)	2013-04-30 01:11:23 +10:00
Robert F-C	d5ad7a0814	Rework change to incorporate CONTROLLERFAN ... Also refactor extruder auto fan logic to simplify further and now only check every 2.5 seconds	2013-04-30 01:08:29 +10:00
Robert F-C	c3cdaceab3	Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1	2013-04-29 22:13:55 +10:00
Robert F-C	1c127217df	Make DOGLCD merge neater.	2013-04-29 22:03:37 +10:00
Robert F-C	7f57f28ccc	Add lcd_buzz function to ultralcd.h so that non-LCD code can make use of lcd's buzzer. ... Argument order of lcd_buzz was set to mirror that on tone(). Change default M300 frequency to something audible.	2013-04-29 21:50:52 +10:00
Robert F-C	788d62bcc4	Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1 ... Conflicts: Marlin/Marlin.pde Marlin/ultralcd.cpp Marlin/ultralcd_implementation_hitachi_HD44780.h	2013-04-29 21:13:46 +10:00
Lukasz Stefanowicz	d71f1e9bf6	Add (as an option) slower SD transfer mode	2013-04-24 10:50:57 +02:00
ErikZalm	db5bb8546d	Merge pull request #452 from MStohn/Marlin_v1 ... 128x64 RepRapDiscount Full Graphic Smart Controller support	2013-04-23 09:43:37 -07:00
daid	4b2ece159b	Merge pull request #453 from brackendawson/Marlin_v1 ... Make Gen7 1.4+ heater temp sensort pins match silkscreen.	2013-04-16 10:12:25 -07:00
Bracken Dawson	d5ee2a5a62	Make Gen7 1.4 heater pins match silkscreen	2013-04-16 17:37:38 +01:00
MaikStohn	7ac6d7f78e	FIX: Speedup - no explicit display clear needed in u8glib	2013-04-16 14:22:24 +02:00
MaikStohn	13596e8722	Added RepRapDiscount FULL GRAPHIC Smart Controller	2013-04-16 14:21:39 +02:00
MaikStohn	3a6abe1d6e	Removed STB custom font hack from u8glib library and moved to marlin project	2013-04-16 13:54:39 +02:00
MaikStohn	16afbf9bfa	FIX: adopted latest changes from hitachi implementation	2013-04-16 13:51:48 +02:00
daid303	34bca48b98	Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1	2013-04-15 15:11:38 +02:00
daid303	ac52dcc174	Updated the card menu and watch messages to make it more informative.	2013-04-15 15:11:22 +02:00
Stefanowicz	31bb3fb297	Fix: Build error when EEPROM_SETTINGS is defined and PIDTEMP is undefined	2013-04-12 18:04:32 +02:00
daid303	c80a78bb70	Lower the default max E feedrate a bit. With the stepper fix this is much to high.	2013-04-12 13:54:38 +02:00
Simon Oliver	5d5909fc25	Fix failure to compile with heated bed: remove call to non-existant scaleBedPID().	2013-04-12 13:32:47 +02:00
Simon Oliver	93f0463b21	Allow Edit menu to call fn after edit; Fix PID Ki and Kd display in menus; Actually use changed PID and Max Accel values ... Add new 'callback' edit-menu types that call a function after the edit is done. Use this to display and edit Ki and Kd correctly (removing the scaling first and reapplying it after). Also use it to reset maximum stepwise acceleration rates, after updating mm/s^2 rates via menus. (Previously, changes did nothing to affect planner unless saved back to EEPROM, and the machine reset). Add calls to updatePID() so that PID loop uses updated values whether set by gcode (it already did this), or by restoring defaults, or loading from EEPROM (it didn't do those last two). Similarly, update the maximum step/s^2 accel rates when the mm/s^2 values are changed - whether by menu edits, restore defaults, or EEPROM read. Refactor the acceleration rate update logic, and the PID scaling logic, into new functions that can be called from wherever, including the callbacks. Add menu items to allow the z jerk and e jerk to be viewed/edited in the Control->Motion menu, as per xy jerk. Conflicts: Marlin/language.h	2013-04-12 13:31:30 +02:00
Bart K	4fa2260a59	Fixed cardreader.h to resolve issue #440 (Pull Request #425 missing file)	2013-03-31 19:59:16 -04:00
Erik van der Zalm	038d405254	Corrected #endif in language.h	2013-03-31 20:28:29 +02:00
Dirk Eichel	443aaa30bf	Removed GIT fragments ... Seems that there was something wrong while merging	2013-03-30 23:26:42 +01:00
ErikZalm	7f622467fc	Merge pull request #425 from kefir-/m928_logging ... M928 logging	2013-03-30 08:50:34 -07:00
ErikZalm	86867928ac	Merge pull request #434 from DDRBoxman/Marlin_v1 ... Add support for M300: Play beep sound	2013-03-30 08:49:54 -07:00
ErikZalm	9a38cad6f0	Merge pull request #430 from STB3/GLCD_128x64_dots ... Final task of the 128x64dots GLCD implementation	2013-03-30 08:49:14 -07:00
ErikZalm	7a5c474d91	Update Configuration.h	2013-03-28 21:27:50 +01:00
Dirk Eichel	4e448b700a	Merged fetched files from Marlin_v1 branch ... Pull requests: #414 #433 #432 #428	2013-03-26 21:43:04 +01:00
ErikZalm	9f2862ce48	Merge pull request #414 from whosawhatsis/Marlin_v1 ... regenerated thermistor table 7	2013-03-25 13:14:49 -07:00
ErikZalm	9fb8bd5685	Merge pull request #433 from whosawhatsis/bang-mode ... Separate PID_MAX from BANG_MAX	2013-03-25 13:11:34 -07:00
Colin Edwards	0d075378d5	Add LARGE_FLASH define and enable it for some of the beefier boards ... The LARGE_FLASH flag allows superfluous features to be excluded on boards with less memory	2013-03-25 10:42:27 -05:00
Colin Edwards	9a1c90471f	Ignore unused beeper pins	2013-03-25 10:28:15 -05:00
Colin Edwards	1a0f889803	Add support for M300: Play beep sound	2013-03-24 23:35:05 -05:00
Robert F-C	9322c408c6	Updated for LiquidTWI2 library version 1.2.3 ... The new version of the library means that PANELOLU no longer needs to be defined in LiquidTWI.h (the library file can be used as is) and the new version of the library also enables the buzzer on the Panucatt VIKI panel.	2013-03-24 18:19:58 +11:00
whosawhatsis	fd5b7e0cec	Separate PID_MAX from BANG_MAX ... This allows PID_FUNCTIONAL_RANGE to use a maximum duty cycle higher than PID_MAX. This is useful for powerful heaters to heat quickly in bang-bang mode, but use a lower duty cycle that is easier to stabilize in PID mode.	2013-03-22 18:16:26 -07:00
blddk	e5a853a3d0	Added automated extruder fan function	2013-03-22 18:49:05 +01:00
blddk	72419f69a9	Added rumba	2013-03-22 18:41:54 +01:00
blddk	91bea43332	Added rumba pinout	2013-03-22 18:29:47 +01:00
blddk	d2b00fe486	Removed html and added rumba ... Found some unwanted html at the bottom of the file which caused it to not be able to compile. Also added rumba as machine.	2013-03-22 18:28:16 +01:00
Dirk Eichel	6c66cae694	GLCD init screen cosmetics	2013-03-19 21:25:11 +01:00
Dirk Eichel	f3e0e5184d	Add include selector between char. LCD and GLCD	2013-03-19 20:59:21 +01:00
Dirk Eichel	5d3862f9d1	Modified u8glib logo on welcome screen	2013-03-19 20:32:23 +01:00
Dirk Eichel	0b320f75e9	Removed debug code, add some comments	2013-03-19 20:29:25 +01:00
Dirk Eichel	5f1cd70122	Add code to lcd_update() for GLCD ... This code selects between the routines for the GLCD or the char. display.	2013-03-19 20:19:16 +01:00
Dirk Eichel	a49c09a776	Add variable for animated fan, add float conversion w/o sign ... A new variable was introduced to allow fan animation on the GLCD. Add additional float to string conversion routine without sign character. This is used for the coordinates visualisation on the GLCD.	2013-03-19 20:13:23 +01:00
Dirk Eichel	26d8863111	Add library selection between GLCD and char. LCD	2013-03-19 20:03:47 +01:00
Dirk Eichel	4a141a694f	Marlin code for GLCD display ... This contains the menues, status screen etc...	2013-03-19 19:59:56 +01:00
Dirk Eichel	83c790a020	Add bitmap graphics for GLCD ... 1. Marlin welcome screen 2. Status screen symbols 3 Extruders, heated bed, animated fan logo 1 3. Status screen symbols 3 Extruders, heated bed, animated fan logo 2	2013-03-19 19:57:35 +01:00
Dirk Eichel	233df9cca0	Add missing LF at the end of the file	2013-03-19 19:12:33 +01:00
Dirk Eichel	bb0de75a92	Removed umwanted HTML code ath the end of the file ... Sorry for that. This does not lead to compile errors. I removed the unwanted code to make it clean.	2013-03-19 06:46:05 +01:00
Ryan Turner	7c47e7162d	Adding Maker's Tool Works heated bed thermistor	2013-03-18 22:53:37 -05:00
daid	af78d0cbfa	Merge pull request #1 from illuminarti/Fix_E_Speed ... Fix step rate bug (especially for retraction)	2013-03-18 23:36:11 +01:00
Dirk Eichel	9a78f321a4	Add pins for Motherboard variant 64 ... These definition contain also the definition for the graphics LCD.	2013-03-18 23:36:11 +01:00
Dirk Eichel	5de25ccd20	Add Motherboard variant 64 - STB V1.1 ... Definition for the graphic LCD are already in it, they will not harm the configuration as they are only defined constants	2013-03-18 23:36:10 +01:00
daid	d6ce63c49c	Merge pull request #411 from STB3/Marlin_w_STB_Board_support ... Add STB board support to Marlin (next step towards graphic LCD implementation)	2013-03-18 07:57:39 -07:00
Ketil Froyn	f036be7c4e	Clean up tab/whitespace from last commit	2013-03-16 23:11:58 +01:00
Ketil Froyn	07e11c7cf5	Add command M928 to enable logging to file of received gcode commands	2013-03-16 23:02:57 +01:00
daid	92782f9252	Merge pull request #1 from illuminarti/Fix_E_Speed ... Fix step rate bug (especially for retraction)	2013-03-15 09:07:34 +01:00
whosawhatsis	6a61a3c0b4	missing comma in last commit	2013-03-08 16:15:49 -08:00
whosawhatsis	f0aee4101a	regenerated thermistor table 7 ... Generated with createTemperatureLookup.py. The old table crapped out at 270C, which was a problem for polycarbonate.	2013-03-08 13:41:49 -08:00
Nicolas Rossi	aba67e2449	No bed config for RAMPS ... The motherboard 35 is a config without bed with this pins setting : D8 Extruder D9 Fan D10 Controller Fan	2013-03-05 15:51:24 +01:00
Nicolas Rossi	6504e96165	Turn off power supply off-load ... Disable the high current output and wait a little before to turn off, because the interrupting capacity of the PSU is unknown. Could be a function if needed by other.	2013-03-05 15:03:48 +01:00
Nicolas Rossi	86bf911139	Toggle menu for PSU from LCD pannel ... From the prepare menu, accessible when is not printing, you have the possibility to turn off the PSU when is on et vice versa. From the host, you can turn off or turn on the PSU then the menu is updated accordingly. From the LCD message, the printer status is reported ready or off respectively when the PSU is on or off.	2013-03-05 14:52:51 +01:00
Robert F-C	7bad72359c	Support encoder click on PANELOLU2 being read through I2C ... This change also handles the case where the pause/stop/restart button on the VIKI is not used. Make LCD I2C buzz sound the same as the normal buzz (300ms is too long for quick feedback).	2013-03-03 18:47:50 +11:00
Robert F-C	1daf2f3256	Number of extruders is not an advanced configuration - it is a basic property.	2013-03-02 16:14:19 +11:00
Robert F-C	f1263d3f88	Further reduce code by using precompiler logic	2013-03-02 16:12:11 +11:00
Dirk Eichel	140e095c6e	Add pins for Motherboard variant 64 ... These definition contain also the definition for the graphics LCD.	2013-03-01 17:47:32 +01:00
Dirk Eichel	b2c1c64fb1	Add Motherboard variant 64 - STB V1.1 ... Definition for the graphic LCD are already in it, they will not harm the configuration as they are only defined constants	2013-03-01 17:39:54 +01:00
Dirk Eichel	ceb5ee38af	Replaced corrupted language.h file on local PC with current from ErikZalm/Marlin	2013-03-01 17:27:57 +01:00
Dirk Eichel	8efd4cfd73	fixed merge conflict	2013-03-01 16:27:35 +01:00
Robert F-C	372e12f83f	Implement automatic extruder/cold-end fan control based on temperature ... This change allows fan outputs to automatically turn on/off when the associated nozzle temperature of an extruder is above/below a threshold temperature. Multiple extruders can be assigned to the same pin in which case the fan will turn on when any selected extruder is above the threshold. It also makes the M42 command compatible with the M106/M107 command. The majority of the logic in this change will be evaluated by the compiler at build time (i.e, low code space requirements).	2013-03-01 21:57:23 +11:00
Robert F-C	6beb42cdf6	Attempt to address Bernhard's comments ... Refactor configuration to try to make items clearer (what defines a panel vs what is user changeable).	2013-03-01 01:17:07 +11:00
Robert F-C	839bef6d5d	Fix Configuration.h file to not define LCDs be default. ... Also fix compile time check in Marlin.pde	2013-02-28 02:32:20 +11:00
Robert F-C	1292d735ba	Converge all I2C LCD branches (PANELOLU2, VIKI & PCF8575) ... This includes refactoring the buttons code to remove a large amount of non-pin dependent duplication from pins.h.	2013-02-28 02:04:51 +11:00
daid303	4eb81a69e6	Only compile the new extruder offset code if you have multiple extruders.	2013-02-27 12:32:07 +01:00
daid	3e9cd334a4	Merge pull request #383 from dob71/jeff ... Hotend offset handling for multi-extruder machines	2013-02-27 03:10:18 -08:00
MendelMax	67710df9f3	Made i2c mode wok with the hardware I am able to test (ywrobot / sainsmart i2c LCD 2004) ... Removed incorrect LiquidCrystal_I2C Library	2013-02-26 22:22:12 +00:00
Bob Clough	b6209c86dd	Added import of Wire Library to make I2C LCD support compilable	2013-02-25 15:15:23 +00:00
Bob Clough	2b567d1df5	Added I2C port expander support to HD44780	2013-02-25 14:22:14 +00:00
Bob Clough	06272f463d	Added Config variables for activating I2C LCDs and setting type and address	2013-02-25 14:14:46 +00:00
daid303	de3dec7215	Also show the tune menu when USB printing.	2013-02-20 00:54:44 +01:00
Denis Bakin	73d41c10b9	Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into jeff ... Conflicts: Marlin/language.h Marlin/thermistortables.h	2013-02-18 12:10:52 -05:00
daid	63da4dc59a	Merge pull request #398 from DanieleSdei/Marlin_v1 ... Marlin v1, alignment of the Italian language	2013-02-16 15:41:43 -08:00
Daniele Sdei	82e28851bd	Italian language: SD-Card change and SD-Card init	2013-02-16 12:17:29 +01:00
Daniele Sdei	aed5965ad8	Italian language: remove space and some fix	2013-02-16 12:14:50 +01:00
codenamepawel	d360846dd4	Update Marlin/language.h ... Update Polish language  #define MSG_RESUMING "Wznawiam drukowanie"	2013-02-16 03:42:53 +01:00
daid303	2f60e324dc	Fixed #394	2013-02-14 14:04:26 +01:00
daid	5e2abfcdcd	Merge pull request #391 from STB3/Marlin_with_SD-Card_Change_Menu ... Add SD-Card change and SD-Card init. for electronics equipped with LCD Display	2013-02-13 08:56:00 -08:00
Dirk Eichel	a0d4e8e78e	Add Messages for SD Card init. & change	2013-02-13 10:05:18 +01:00
mfeherpataky	bbf0cc1379	Update Marlin/ultralcd_implementation_hitachi_HD44780.h ... Fix to a bug that I just introduced - sorry. Forgot about offset of string length.	2013-02-12 20:06:51 +01:00
Dirk Eichel	c8f1fbd9d8	Add SD-Card change and SD-Card init. ... Add SD-Card change and SD-Card init. for reprap electronics without SD-Chard change detect pin.	2013-02-12 17:35:46 +01:00
mfeherpataky	71ddb8dc60	Update Marlin/ultralcd_implementation_hitachi_HD44780.h ... Use all available characters in narrow LCDs < 20 characters.	2013-02-12 00:03:40 +01:00
mfeherpataky	d2c547c407	Update Marlin/ultralcd_implementation_hitachi_HD44780.h ... Fix to a minor bug with hardcoded LCD_WIDTH that draws edited values outside of the 16 characters width LCDs.	2013-02-11 23:25:24 +01:00
Denis B	70871715e4	Added support for extruder offset handling ... The extruder offset can be specified in the configuration file or adjusted on the fly using the "M218 T# X# Y#" command. The EEPROM support is not yet merged in. The "T#" command can take option "F#" that specifies the feedrate at which the printing head should be re-positioned. If not specified the re-positioning move is not preformed immediately, but the coordinates are adjusted for the printer to properly position the head when the next movement happens.	2013-02-04 23:05:45 -05:00
Denis B	49b2ddc8c1	Cleaned up non-standard characters	2013-02-04 01:41:40 -05:00
Bernhard Kubicek	f8876a7958	Merge pull request #376 from kintel/skip_longfilenames ... Also skip .files and _files with long filenames. I think its better than before. If somebody dislikes it, or wants additional configuration, it can be done in a future step. Thanks, Marius, and nice to have you helping!	2013-02-03 03:05:31 -08:00
daid	18fcc367d2	Merge pull request #371 from Banjer/Melzi_LED_PIN ... Chenged LED_PIN for Melzi boards, added comment about broken versions of...	2013-02-02 03:23:43 -08:00
Bas Spaans	19ce90fe02	Added comment about M42 usage (clean)	2013-01-31 18:20:23 +01:00
Bas Spaans	00fed0a703	Revert "Extended comment explaining M42 usage" ... This reverts commit 01541ee64c.	2013-01-31 18:11:13 +01:00
Marius Kintel	e06d820909	Also skip .files and _files with long filenames	2013-01-31 12:07:42 -05:00
Bas Spaans	01541ee64c	Extended comment explaining M42 usage	2013-01-31 18:00:25 +01:00
Marius Kintel	f24f02e212	compile fix: quickStop() needs stepper.h	2013-01-31 10:43:03 -05:00
Bas Spaans	12c41423ad	Fixed typo in comment	2013-01-30 22:54:04 +01:00
Bas Spaans	0995eaa492	Chenged LED_PIN for Melzi boards, added comment about broken versions of the Sanguino libraries	2013-01-30 22:25:01 +01:00
Bernhard	1d06b10962	Added a feature to have filament change by gcode or display trigger. ... [default off for now] syntax: M600 X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal] if enabled, after a M600, the printer will retract by E, lift by Z, move to XY, retract even more filament. Oh, and it will display "remove filament" and beep like crazy. You are then supposed to insert a new filament (other color, e.g.) and click the display to continue. After having the nozzle cleaned manually, aided by the disabled e-steppers. After clicking, the printer will then go back the whole shebang, and continue printing with a fancy new color.	2013-01-27 13:21:34 +01:00
daid303	408b349a84	Fixed #368. Commented out the wrong pin definition, but explained why it is there.	2013-01-21 15:46:17 +01:00
Daniele Sdei	9ecb267b63	Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1	2013-01-14 15:47:40 +01:00
Daniele Sdei	3cf59f6f9a	add RepRapPro Huxley thermistor tables	2013-01-14 15:36:08 +01:00
daid	c1730e2b08	Merge pull request #363 from yuroller/sanguino_panelolu ... Panelolu pin assignment for sanguinololu	2013-01-10 07:19:37 -08:00
Yuri Valentini	86358dd6cd	Panelolu pin assignment for sanguinololu from http://reprap.org/wiki/Panelolu	2013-01-10 12:23:20 +01:00
daid303	0f3f5d083d	Minor cleanup of the new FAN_KICKSTART code. #334	2013-01-10 11:08:45 +01:00
daid	6ec56fa923	Merge pull request #334 from KevinOConnor/FanKick ... Add feature to briefly run the cooling fan at full speed when it first starts.	2013-01-09 02:47:59 -08:00
daid	965baf2683	Merge pull request #362 from daid/Marlin_v1 ... Finnish language	2013-01-09 02:42:09 -08:00
Kevin O'Connor	3d91bd486c	Add "kick fan" feature - briefly run fan at full speed on start. ... Add a feature to run the cooling fan at full speed for a small period (default 100ms) when first starting the fan. Some fans wont reliably start spinning at low power, and many fans have issue with the PWM at low power. However, once the fan starts spinning it can reliably be set to a wide range of PWM values.	2013-01-08 18:50:15 -05:00
Kevin O'Connor	3f2f94ef28	Be consistent in setting of the fan PWM. ... Always set the FAN PWM value in check_axes_activity() and always use the value of the active move if a move is active.	2013-01-08 18:49:18 -05:00
Henry Palonen	7f30039d2a	+ Finnish translation	2013-01-08 19:21:34 +02:00
daid303	14e1d495ef	Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1	2013-01-08 17:10:30 +01:00
daid303	bbe7d3d0fe	Fixed #312	2013-01-08 17:09:57 +01:00
daid	7ce509b9a7	Merge pull request #361 from yuroller/MakefileSanguino ... Makefile sanguino	2013-01-08 06:22:27 -08:00
Yuri Valentini	9c34c4f05b	fixes for ramps compilation using installed arduino ide	2013-01-08 12:54:31 +01:00
daid303	442ade15a6	Move Gen6 stuff into a proper location.	2013-01-08 12:31:28 +01:00
daid	5fd4582cc8	Merge pull request #242 from Drakelive/Marlin_v1 ... Fixes issues # 216 and # 135 for Gen6 and Gen6 Deluxe board	2013-01-08 03:29:20 -08:00
daid303	8b88e3b386	Fixed #345, Fixed #267.	2013-01-08 12:14:55 +01:00
daid	27843388c6	Merge pull request #360 from njprossi/Marlin_v1 ... Power signal control definitions for other power supplies	2013-01-08 02:58:02 -08:00
daid303	921273baa0	Added optional feature to stop printing when an endstop is hit. Made the Z display on the LCD in 3.2 format instead of 3.1. Added LCD message when and endstop is hit.	2013-01-08 11:53:18 +01:00
Yuri Valentini	7d20ec706e	Added libraries from Arduino 1.0.3 for sanguino build	2013-01-07 17:26:50 +01:00
Nicolas Rossi	437eb3bafc	Initialize PS_ON at startup	2013-01-07 14:57:51 +01:00
Nicolas Rossi	f3c1fc70a9	Power signal control definitions for ATX and others	2013-01-07 14:33:30 +01:00
Yuri Valentini	dad7691df9	makefile for sanguino standalone compilation	2013-01-07 11:08:10 +01:00
Erik vd Zalm	6752cb2d9c	PID now per extruder. Fixed typo	2013-01-06 14:26:23 +01:00
Erik vd Zalm	0ac452e252	Disable is now multi extruder compatible. M84 got a T option.	2013-01-06 13:37:01 +01:00
Johann Rocholl	9e7b5056a0	{X,Y,Z}_{MIN,MAX}_POS are actually in Gcode coordinates.	2012-12-28 16:20:10 -08:00
Daniele Sdei	5f82f03ff3	Add italian MSG_RESUMING.	2012-12-28 11:44:35 +01:00
daid303	5e3873c8db	Add german MSG_RESUMING.	2012-12-25 20:53:11 +01:00
daid303	01aac2a142	Small changes on the LCD panel, let the speed control work better, line up the parameter edit the same as the menu, remove some unused defines, and remove the Z from the 10mm move menu.	2012-12-21 16:14:47 +01:00
daid303	b69cb9fbd9	Change the end of SD cart print message from minutes/seconds to hours/minutes.	2012-12-19 12:26:40 +01:00
daid	30254e3388	Merge pull request #350 from jcrocholl/Marlin_v1 ... Automatically set *_MIN_PIN and *_MAX_PIN according to *_HOME_DIR.	2012-12-17 02:16:31 -08:00
daid303	38ee395ac7	Replace the 1ms delay for 2 nops to get a 100ns delay. #259	2012-12-17 11:12:11 +01:00
daid303	5df5e4c4a2	Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1	2012-12-17 11:09:18 +01:00
daid303	a95dcd74e7	Fix some of the duplicated PSTRs, saving 500bytes of flash with LCD on.	2012-12-17 11:09:09 +01:00
Johann Rocholl	8caf5d252d	Remove bogus blank line.	2012-12-16 12:50:20 -08:00
Johann Rocholl	1c2ecddae4	Fix typo (# missing before define).	2012-12-16 12:33:44 -08:00
Johann Rocholl	6dfb8a2187	Fix home_all_axis to make QUICK_HOME work with Repetier-Host which sends G28 X0 Y0 Z0 instead of G28. Thanks to Matt Schoenholz for reporting this issue.	2012-12-16 12:30:33 -08:00
Johann Rocholl	3b2e5027e5	Merged updates from Marlin_v1.	2012-12-16 12:19:24 -08:00
Johann Rocholl	b39f5d614a	For boards with only one endstop per axis, automatically set *_MIN_PIN and *_MAX_PIN according to *_HOME_DIR.	2012-12-16 12:09:53 -08:00
oni303	ab09fa4bbf	fixed pwm generation at pin D12 and D13 when one of them is used as FAN_PIN on Sanguino, added soft pwm entry for FAN_PIN in temperature.cpp	2012-12-16 01:36:57 +01:00
Sergey Taranenko	5697451c72	fix lcd class	2012-12-14 15:39:47 +04:00
Sergey Taranenko	58e806f3fa	Fix the russial translation.	2012-12-14 15:39:26 +04:00
Sergey Taranenko	50a5ce1dc4	deduplicate messages	2012-12-14 15:37:05 +04:00
daid303	6123a00e64	Fix the german translation.	2012-12-14 11:11:02 +01:00
daid303	7c21716886	Fixed #341	2012-12-14 10:53:11 +01:00
daid303	ae1bc83350	Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1	2012-12-13 13:25:22 +01:00
daid303	596a7e1904	Fix compiling for Arduin < 1.0.0	2012-12-13 13:24:55 +01:00
Daid	b264317fa0	Reverted the patch by KevinOConnor, as it crashes some versions of avr-gcc and caused linking issues.	2012-12-13 12:19:12 +01:00
Daid	673577a31b	Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1	2012-12-13 11:41:34 +01:00
Daid	23022f1a82	Updates to Makefile to compile for Teensy.	2012-12-13 11:41:27 +01:00
daid	96e9db8919	Merge pull request #339 from KevinOConnor/CompilerFlags ... Add additional optimization flags to Makefile	2012-12-13 01:30:17 -08:00
daid303	08356361ac	Fixing a problem with heated beds not working without PID and BED_LIMIT_SWITCHING	2012-12-13 10:25:29 +01:00
daid303	047d037f8c	#ifdef fix for #326	2012-12-13 09:04:41 +01:00
Kevin O'Connor	0908458381	Use gcc "-fwhole-program" optimization. ... Use "whole program" and "link time optimization" features of gcc. The whole-program optimization enables the compiler to evaluate the entire firmware for optimization instead of just one code file at a time. This leads to better overall optimizations.	2012-12-12 23:22:35 -05:00
Kevin O'Connor	16fbb455ef	Use linker "--relax" option. ... The "relax" option enables the linker to convert certain "call" instructions to the smaller "rcall" instruction. This reduces the size of the resulting binary.	2012-12-12 23:22:31 -05:00
daid303	f30b46b2a8	One more fix for #338, I really should get a heated bed to test with.	2012-12-12 23:06:17 +01:00
daid303	65c3f1ffcd	Most likely fixing #338	2012-12-12 21:56:17 +01:00
daid303	7577717b59	Fixed #336	2012-12-12 13:08:26 +01:00
daid303	1a8f54cea1	The big LCD code update. This splits the display and menu implementation. Paving the way for future different displays. It also makes it easier to modify the menu structures while keeping everything consistant. Note that this most likely breaks the translations, which need to be updated.	2012-12-12 11:47:03 +01:00
daid303	6731c094ee	Fix compiling with just an 16x2 LCD and no buttons.	2012-12-12 11:32:33 +01:00
daid303	b99a928a80	Fix the M117 (display message on LCD) when used over USB with checksums.	2012-12-12 09:35:32 +01:00
daid303	55ba90ac19	Add PID functional range setting. With high powered heaters the current functional range of 10 degrees causes high overshoots as the PID needs to kick in before the temperature hits 10 degrees below target.	2012-12-12 09:08:37 +01:00
daid303	5ff5cee8ce	Fix the sensitive pin definitions, there where analogue numbers in the digital pin list. Also made M42 without a P function on the LED_PIN (which was otherwise a useless pin definition)	2012-12-11 14:53:53 +01:00
daid303	8b58edc70e	Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1	2012-12-11 13:38:34 +01:00
daid	d0319d45af	Merge pull request #335 from jcrocholl/Marlin_v1 ... Fix endstop pins for Printrboard	2012-12-11 02:59:58 -08:00
Johann Rocholl	ca409e5531	Fix X/Y/Z_MIN_PIN for Printrboard.	2012-12-11 01:59:48 -08:00
Johann Rocholl	1f45cb0a51	Fix typo in MANUAL_HOME_POSITION (plural S missing) and improve comments.	2012-12-11 01:54:40 -08:00
Johann Rocholl	931a0052ea	Fix typo in MANUAL_HOME_POSITION (plural S missing) and reduce BLOCK_BUFFER_SIZE because 64 wasn't working for some reason.	2012-12-11 01:22:04 -08:00
daid303	46ec4b648c	Added some missing Mxxx comments to M commands. Fixed the unsetting of the timer dividers for the fast PWM fan.	2012-12-11 10:21:44 +01:00
Daid	724f5aa36b	Update on makefile for moved Arduino addons.	2012-12-10 12:06:30 +01:00
daid303	6d9dfa96c3	Move the Arduino related stuff out of the Marlin tree, as they are not directly related to Marlin functionality but addons for the Arduino IDE. Also split up the addons for pre 1.0.0 Arduino and post 1.0.0 Arduino.	2012-12-10 12:02:29 +01:00
daid303	3fb07d9b8d	Add MINTEMP/MAXTEMP error to LCD, and fix temperature bug with more then 1 extruder.	2012-12-10 10:48:46 +01:00
Johann Rocholl	8e2519e88b	Add realtime delta geometry in Marlin_main.cpp.	2012-12-10 01:04:12 -08:00
Johann Rocholl	cec7283b21	Enable QUICK_HOME for deltabot.	2012-12-10 00:43:47 -08:00
Johann Rocholl	2292441f0c	Use X/Y/Z_MAX_PIN instead of X/Y/Z_MIN_PIN for top endstops on deltabot.	2012-12-10 00:43:14 -08:00
Johann Rocholl	c430906d3b	Deltabot settings and configuration adjustments.	2012-12-10 00:10:56 -08:00
daid303	82c8724b33	Fix compile with PID_DEBUG	2012-12-09 23:50:12 +01:00
daid303	9b160972a1	Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1	2012-12-09 23:46:42 +01:00
daid303	e036750bdf	Use the disable macros on initialization. Which fixes a bug when there is no pin defined for stepper enabled (motherboard 4)	2012-12-09 23:46:25 +01:00
Daid	fcd9de72ef	Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1	2012-12-09 23:31:07 +01:00
Daid	32d4373e0f	Add printrboard and brainwave to Makefile.	2012-12-09 23:30:55 +01:00
daid	b3ddbcee2a	Merge pull request #329 from jcrocholl/Marlin_v1 ... Add Printrboard and Brainwave to pins.h and fastio.h	2012-12-09 14:29:26 -08:00
Daid	29435dfb4b	Proper avr for Sanguino in Makefile.	2012-12-09 23:02:03 +01:00
daid303	52158dffcc	Big temperature code update. No longer converts back and forwards between temperature and raw sample value. Reducing complexity, removing code. Also named some variables better. While keeping the safety intact and functionality the same.	2012-12-09 23:00:06 +01:00
Daid	ca7acbe6d9	Allow specification of which arduino hardware subvariant in Makefile.	2012-12-09 19:19:57 +01:00
Johann Rocholl	33247733e0	Teensylu and Printrboard use different analog pins for thermistors.	2012-12-09 02:19:13 -08:00
Johann Rocholl	621c24a10f	AT90USB is only defined after pins.h is included.	2012-12-09 01:40:33 -08:00
Johann Rocholl	6cba11f087	Stop redefining MOTHERBOARD and #define AT90USB instead. Also put #ifndef AT90USB around the HardwareSerial_h trick, so now Printrboard / Brainwave support compiles on Arduino 1.0.2 as well.	2012-12-09 01:32:09 -08:00
Johann Rocholl	4d351b4846	Improved formatting and comments for consistency.	2012-12-08 20:15:53 -08:00
Johann Rocholl	a30007caa4	If fastio.h is not messed up then Teensylu and Printrboard are actually using the same pins.	2012-12-08 19:46:42 -08:00
Johann Rocholl	6aa87a7b67	Use the same fastio.h definition for AT90USB1286/7 and AT90USB646/7.	2012-12-08 15:16:38 -08:00
Johann Rocholl	b1c38d4c82	Avoid compiler warnings (redefined MOTHERBOARD) in Arduino 1.0 and greater.	2012-12-08 11:34:18 -08:00
Johann Rocholl	42e21bb06e	Add support for Printrboard (from https://github.com/lincomatic/Marlin) and Brainwave (from https://github.com/metrix/Sprinter).	2012-12-08 10:49:01 -08:00
Johann Rocholl	ce4b5bbeaa	Add AT90USB646 support from Sprinter to fastio.h.	2012-12-08 10:45:58 -08:00
Daid	f413aa33b3	Small makefile change, posibility to add defines on the commandline, and fix compiling with watchdog enabled when using the Makefile.	2012-12-08 11:49:53 +01:00
daid303	587154c01b	Fix the WATCHPERIOD implementation. It did not work correctly in a multi extruder setup, it did not work after 32 seconds after startup (int16 used as millies timestamp). And it did not work if you gave an M104 or M109 when the target was already around the target setpoint. So on average, it did not work at all. The new implementation should be robust in detecting a failure to heat up.	2012-12-06 10:36:07 +01:00
daid303	1f27870d41	Fix compiling the watchdog error message when the manual reset watchdog is used.	2012-12-06 10:27:50 +01:00
daid303	c5d4225804	Mistake there, not sure why I did that. My bad.	2012-12-05 20:23:13 +01:00
daid303	529748894c	Minor changes in the temperature code for some cleanup.	2012-12-05 19:54:01 +01:00
daid303	4e26ecc940	The Partial release message (which does not really tell you anything) overwrites the final print time on the LCD, which is a real shame. So I removed the message.	2012-12-05 19:32:26 +01:00
daid303	c421774422	The Partial release message (which does not really tell you anything) overwrites the final print time on the LCD, which is a real shame. So I removed the message.	2012-12-05 19:32:02 +01:00
daid303	16078e47d4	Fixed #325	2012-12-04 16:27:21 +01:00
daid303	6a9bee27cc	Changed the naming of some LCD functions, so the names match better what the function does. Also moved around some prototypes for general cleanup.	2012-12-03 12:52:00 +01:00
daid303	94ea26ff46	Some minor changes on code style. And a bugfix where the counters for positioning in the stepper where wrong depending on compiler settings. (Caused strange values to reported back with M114 and endstop triggers). Also fixed compiling with FWRETRACT enabled.	2012-12-03 12:13:20 +01:00
daid303	6c51fe5039	Fix the bug where the SD percentage calculation is wrong when the file is larger then 42MB	2012-12-03 11:35:36 +01:00
brupje	57429cb9fe	Fix for keypad	2012-11-29 21:42:19 +01:00
daid303	97fa2a9c30	Few simple fixes that save RAM, as static strings are stored in RAM by default.	2012-11-28 10:30:34 +01:00
Daid	c94ca24adc	Fixed #317	2012-11-24 17:32:30 +01:00
Daid	99e9554edd	Some fixes in the Makefile to support Arduino 1.0.0 or higher and added the Rambo. Still needs some more work for the different arduino hardware variants.	2012-11-24 11:46:31 +01:00
Erik vd Zalm	dbbf050005	More rambo fixes	2012-11-21 20:53:56 +01:00
Erik vd Zalm	f934d0ef5b	Merge remote-tracking branch 'tonokip/Marlin_v1' into Marlin_v1 ... Conflicts: Marlin/Configuration.h	2012-11-21 20:36:30 +01:00
Erik vd Zalm	e48dfcc2b3	Tmp copy before merge	2012-11-21 20:29:31 +01:00
Erik vd Zalm	b98fb17fe9	Small FREQUENCY_LIMIT changes	2012-11-21 20:17:44 +01:00
daid	bce67ec2c9	Merge pull request #312 from gege2b/Marlin_v1 ... Added french translation	2012-11-18 13:43:07 -08:00
Gege	9b1d2483a0	I hope last changes to french translation	2012-11-18 22:34:56 +01:00
Gege	b1adc567da	Correction to french translation (non-ASCII chars only)	2012-11-18 20:00:41 +01:00
Gege	0807d82af0	Correction to french translation (plain text only)	2012-11-18 19:39:56 +01:00
Erik vd Zalm	5cd7a90b32	Added new temperature lookup table creation tool. This one uses stein hart-hart equations. ... You need 3 temperature resistance:combinations. This gives a better result then using beta.	2012-11-16 23:51:05 +01:00
gege2b	bb119739b0	Added french translation	2012-11-16 18:38:50 +01:00
daid	df8dd5ac21	Merge pull request #306 from nothinman/Marlin_v1 ... Added automatic build numbering.	2012-11-14 01:59:33 -08:00
MaikStohn	2b7b1e52b1	allow marlin internal 0°C represenation	2012-11-13 14:37:08 +01:00
Martin Lukasik	2f771b3979	Added automatic build numbering.	2012-11-12 21:06:59 +00:00
daid	9bebe9b631	Merge pull request #302 from nothinman/Marlin_v1 ... Added Polish translation. Cosmetic changes to English.	2012-11-12 12:13:30 -08:00
daid303	a2032afa3a	Fixed #303	2012-11-12 21:04:07 +01:00
Martin Lukasik	6a55ca8370	Added Polish translation. Cosmetic changes to English.	2012-11-12 15:54:07 +00:00
daid303	8f20562f49	Fix some of the crowded code style. And fixed the conditional. #300	2012-11-12 15:49:40 +01:00
daid303	43018a48c4	Fix for a few -Wextra warnings.	2012-11-12 15:35:28 +01:00
daid303	72586eb30a	Solved few warnings.	2012-11-12 09:29:12 +01:00