Model UV as power-invariant, so that scaling P doesn't change the
intercept location (that is, the zero point remains at the same
temperature even for more powerful heaters).
NOTE: It's not clear to me whether this is generally true (couldn't
find a datasheet from the same heater in diffent power variants
showing the efficiency loss)
- Expose TEMP_MODEL_fS and TEMP_MODEL_LAG as D and L respectively,
initializing the default values based on the previous hard-coded
values.
- Always round L to the effective sample lag to future-proof model
upgrades or changes (the stored value _is_ the effective value).
- Introduce UV as a new linear term for PTC heaters, defaulting
to an identity for model backward-compatibility.
Use "echo:" for thermal model error reporting to avoid octoprint
automatically sending a M112 kill.
Keep using "error:" instead for other thermal errors (MAXTEMP/etc).
This should allow resuming a thermal mode pause with the default
octoprint settings.
Alert messages are intended to persist above "info" messages, thus
preventing further calibration status updates to be shown (such as
thermal model calibration).
Just set the message as a regular status message.
Fixes#3892
During calibration model warnings are possible/normal. This is
apparently leading some into thinking the hotend might be faulty
and abort the calibration with a hard reset.
Disable warnings/beeps during calibration.
Rely on the error threshold only.
During thermal errors all fans are set to full speed.
When the print is resumed or stopped *and* the thermal error is gone,
also restore the autofan state.
Fixes#3893
Running `M310 A` should set the TM calibration bit status if the
autotune procedure was successful.
Partially addresses #3891 and #3890, since running `M310 A F0` should
*still* count as valid calibration data and is not something that can be
replicated by using the LCD (which enforces self-test).
This fixes#3891 without having to set the calibration bit, meaning
that if the model is later re-enabled without a real calibration, a
prompt is shown as expected.
Disable the watchdog early in the program
More documentation for pins file
retrigger build
fix watchdog not getting disabled on user app boot
Fix interrupts not enabled during setup()
Follow Marlin's behavior and simply insert a delay for the requested
duration when using M300 S0.
When S is not specified, use the default tone instead.
Fixes#3856
Disabling the model during a warn/error condition will also stop
updating the warning/error flag, keeping the printer in an error state.
Clear all flags as well when changing model settings.
Instead of checking for explicit versions, resume the wizard if some
(new) wizard is missing.
This handles both the old SELFTEST check, the new thermal model
and any future check in the same fashion.
Update the eeprom FW version as soon as migration is complete, to avoid
resetting the CALIBRATION_V2 variable at each reset.
Do not implicitly reset the calibration steps for WizState::Run: do this
only for the menu action.
- Handle the conversion from the V1 calibration status to the V2 bitmap
for all past FW versions.
- Allow to run the wizard in "Restore" mode (for example during upgrade
or service prep) to complete any missing steps.
- Fix service prep to use the above feature by clearing the appropriate
calibration bits.
- Remove exceptions for FW 3.2.0.4 which can now be handled cleanly.
Simplify status tracking:
- S::Restore to continue to the next logical wizard item
- S::Finish for a successful failure
- S::Failed to exit while showing a failure
- Move calibration status/declarations to util.h
- Allows to query the status of each step independently without assuming
any order
- Allows to extend the calibration with new steps transparently
- Generalize force_selftest_if_fw_version() so we can check when upgrading
between arbitrary FW versions.
- Do not call update_current_firmware_version_to_eeprom() prematurely
when forcing self-test (if a reset happens before self-test completes,
the check would be incorrectly skipped on the next run).
