* Combine repeated calls into functions with much less parameters -> 2KB
down.
* Save some bytes by removing unnecessary 1-character strings: "x" -> 'x'
used in SERIAL_xxx printing macros.
This is also saves some CPU cycles
* Fix compilation for MK25S and MK3
* Copy surrounding indentation
* Fix compilation for a rare HW setup
* rename mesh_planXX_buffer_line back to mesh_plan_buffer_line
* Remove active_extruder from remaining plan_buffer_line_destinationXYZE
calls and one more fix of indentation
* Add and update missing translations
- updated in Firmware/ files the missing `c=xx` column and `r=yy` rows.
- added missing translations to lang/lang_en*.txt
Everyone is developing and adding messages to serial and especially to LCD PLEASE add `//// c=xx` or `//// c=xx r=yy` comments.
Preparing translations files without that information is a pain in the ... and takes way more time for somebody else
to review to code as it would take you.
* No need to have `MSG_abcde` again in comments `////` in `messages.c`
* German translation
* Missed a space
* Use the same format as somewhere else
* French translation.
I am not a native French speaking person, so please excuse my mistakes I may have done.
* Spanish translation.
I am not a native Spanish speaking person, so please excuse my mistakes I may have done.
* CZ translation
* Fix typos
* Another fix
It is
Dimmwert and not Dim Wert
* Fix issues reported by `lang-check.py`
* Add "difficult" messages containing `%`
* Updated MSG and German translation
* removed a translation as it breaks the language selection
* No need to wait until any-key is pressed
* No need to wait any-key is pressed
* Fixed two LF issues
* Updated PO files
ready to be send to translators
* Add missing italian translations
* Improve some existing italian translations
* More italian fixes
* More italian fixes
* Add exceptions in editorconfig for po files to avoid recoding
* Fix typo
Thanks @DRracer for pointing out
* Italian translation by @wavexx
* Update po/new/*.po files
* Update after merging MK3 branch
* Update French translation and some c=xx comments
Big thanks to @awenelo @carlin57 for helping with the french translations and their comments.
* Update po files after French translation
* Fixed most `lang-check.py` reported translation errors for Czech and German.
Two Czech have to be reviewed as these are too long.
One German is correct as it is shown in c=20 r=2 but is 1 char longer than this to split the message.
One German translation seams to be to long but have to review the actual max length
* Fix `lang-check.py` Spanish translation errors
There have been quite lot TOO long messages,
Can't imagine that nobody every complained about that.
* Fix `lang-check.py` Italian translations errors
* Update not_tran and not_used files after fixing several translations
* Some more error fixes and update of `po` files
* Polish translation
* Czech updated
* Fix typo
* no need to translate `\x00` if it is the same
* Polish: Runouts->Koniec
* Polish: Runouts->Konce f ... hopefully the last change
* Added MK2.5/s auto power mode to eeprom doxygen
* Final updates.
- Compiled all versions with multi-languages
- Compiled all versions with EN_ONLY
- updated all /lang/po/Firmware*.* files
* Add crlf attributes for po files
As done for editorconfig, this similarly forces git to handle
po files consistently in DOS format.
* Further improvent of IT translations
* Updated translation
Added cleanup to PF-build.sh
* remove lang/not_tran* and lang/not_used mistakenly added into the PR
Co-authored-by: DRracer <drracer@seznam.cz>
Co-authored-by: Yuri D'Elia <wavexx@thregr.org>
Co-authored-by: D.R.racer <drracer@drracer.eu>
As pointed out by @leptun, with MMUs the combination of old/new filament
profiles in the same print is a likely scenario as we transition towards
LA1.5. Reset the detection state also with K0.
Move la10c_reset into finishAndDisableStepper, which is called in both
via lcd_print_stop() and indirectly via M84, saving some space.
M84 is checked-for to determine a complete file, so it's a superior
candidate to G80 (which some people avoid due to MBL issues).
Allow the LA 1.5 MAX value to be configured in Configuration_adv.h.
Define a customizable LA10<>15 detection threshold in function of the
above limit.
Clamp the result of of the LA10->15 return value to always
respect the new LA_K_MAX.
* MK3S IR sensor detection and safe operational range fix
* debug, change of fsensor_IR_check behavior
* more doc + disable debug print voltage
* fix displaying MSG_04_OR_NEWER and MSG_03.... kudos to @ovariludovit
* better handling of fsensor not responding scenario
* Fix missing (hex) in D5 code
* Make ALL D-codes available for DEBUG mode
until now D3 and D5 needed to be defined separately
* Forgot to modify Marlin_main
Just after setting up the w2m matrix, call "clamp_to_software_endstops"
on the current_position (initially [0,0,0]) to move it to the effective
minimal position, which is usually [0,0,non-zero] due to MIN_Z and the
negative probe offset.
This is required to calculate correctly the first relative move:
planning X+10 would unexpectedly calculate a Z shift otherwise.
- Hide all prototypes related to PAT9125 to force all callers
to check for the proper sensor, since the handling differences
are substantial
- Remove unneeded lenght accounting from the stepper isr as as
consequence.
- Keep detailed soft failure counts for the MK3 on the "last print
failures" status screen, but fix build on variants without a PAT9125
by fixing the lcd stats function.
The filament sensor "chunk lenght" needs to be updated every time the
E axis resolution is changed in order to trigger at the same distance.
Introduce a new function fsensor_set_axis_steps_per_unit() and use
it consistent during init, in M92 and M350.
When upgrading K values of a LA1.0 print, also adjust E-jerk settings
(<2) if permissible according to current accell limits. The same is also
true when jerk is set mid-print via 'M205 E'.
Existing values are always restored when switching to another
compatibility mode.
TODO: Since this is stateful, we will need to save the current print
mode / acceleration and jerk in the eeprom for this to survive a power
panic (see prusa3d#2456).
M24 was always cleaning the last print failstats. But because M24 is
used to restore a print after power failure (by setting the seek
offset), it would also reset the stats incorrectly after resuming.
Check for the file index position and reset the stats only when a print
is started from the beginning of the file.
Apply the same logic to M32 and similarly handle the LA10->15 conversion
(do not re-apply the adjustment for a resumed print).
There is a chance that current_block can be NULL despite
the queue being non-empty. This can happen early after a block has been
queued, but before the isr has picked it up for processing, and/or when
the current block is at the last step and is being discarded.
Check for current_block directly to avoid this race.
Both during early init and in uvlo_tiny, display "POWER PANIC DETECTED"
if enough charge is left.
This is not worth doing in regular uvlo_, as we want to give full
priority to the X motor
If power has been lost during startup already a falling edge would be
skipped, causing the print to continue and lose its state without
being able to save again.
Check for a low line after arming the interrupt and simply wait
for reset.
Do not allow uvlo_tiny() to trigger before the previous print has
already been recovered.
A quick repeated power failure could cause uvlo_tiny to overwrite
the Z position before it has been correctly recovered.
enable/disable_z behave differently when PSU_Delta is defined.
During powerpanic and kill however we do *really* need to save energy
and poweroff the motors.
Rename enable/disable_z as poweron/poweroff_z and define some aliases so
that we can use the low-level function where needed.
Use 2 bytes to store extruder temperature during UVLO.
Re-use the storage of EEPROM_UVLO_TINY_Z_MICROSTEPS which has been freed
by previous changes.
Fixes#2303
- In both uvlo_ and uvlo_tiny, calculate Z usteps properly and adjust
the Z position to a true fullstep before disabling the motor. This
avoids shifs during recovery.
- In uvlo_tiny, instead of moving up indefinitely, adjust Z just
once using the smallest move possible (new def UVLO_TINY_Z_AXIS_SHIFT)
- Perform all the uvlo/recovery processing in physical coordinates
and MBL off: there should be no automatic Z movement!
- Disable heaters in both handlers to conserve more power.
- Add timing information to uvlo_tiny too.
- During recovery, to switch between physical and logical positioning
introduce a new "PRUSA MBL" gcode as most of the procedure is
enqueued, and no existing gcode was available.
There is frequently plenty of power left during a PP. Take advantage of
it by moving the extruder to either side of the axis to detach
completely the nozzle from the print.
Re-enable Z during this move to avoid losing the current step.
When the printer is connected to a USB host during a PP (and the host
does not lose power), the rambo can linger for longer, sometimes for
long enough to recover the print state. Drain some more power.
If the motors are off-phase, this is more likely to "bump" them to an
incorrect/reverse full-step, doing worse.
We need to ensure the motors are already positioned on a fullstep
during power panic instead.
Remove the PSU_DELTA exception: Z _always_ needs to be powered here.
Also clear the UVLO flag when using lcd_print_stop. This prevents an
aborted print which has been cancelled while unparking (just prior to
recover) to come back again at the next startup.
- Initially restore the last E position from the eeprom in any case, not
just when using absolute mode (although unnecessary: since it will be
reset later), fixing a possible unitialized position and crash during
recovery (thanks to @leptun)
- Remove useless extra calls to put the extruder in relative mode:
the extruder already starts in relative mode and is later switched to
absolute.
- Replace incorrect calls to STRINGIFY with sprintf_P
- Retract after pressure has been restored in uvlo_tiny, to be
consistent with a regular uvlo (remove the bogus double unretract
as a result).
- Set the real E position prior to the panic *after* the retraction,
using the now-fixed G92.
Do not process serial commands when re-enabling the global isr.
While printing via USB and a power panic is triggered, *any* extra
command should be ignored.
Abuse the "saved_printing" variable to inhibit serial processing.
To maintain an accurate step count (which is required for correct
position recovery), any call to plan_set_position&co needs to be done
synchronously and from a halted state.
However, G92 E* is currently special-cased to skip the sync (likely to
avoid the associated performance cost), causing an incorrect E step
count and position to be set. This breaks absolute position recovery,
miscalculation of the LA factor and possibly other weird issues.
We rewrite the handling of G92 to always sync but still special-case the
frequent "G92 E0" for performance by using a free bit in the block flags.
To avoid a sync, we relay the request for reset first to the planner
which clears its internal state and then relays the request to the final
stepper isr.
According to the reprap wiki, M46 has been assigned to display its assigned IP address, but has been disabled.
Now that Toshiba FlashAir IP address processing is working, I activate the M46 code so that I can read the IP address information via serial.
When check_z_endstop is set, Z_MIN_PIN is checkend regardless of the
moving direction to support Z calibration. This prevents the ability
to use _just_ SG when moving upwards.
But since we know the extruder is at Z_MIN, it's always safe to raise
irregardless, so we can dodge the issue.
Do not unconditionally enqueue a Z move if no move has been requested.
Since Z is calculated using the absolute current (saved) position and
scheduled for later execution, the queue order becomes relevant.
In preparation for #2161, use MBL (G80) as a "new print" boundary
instead of just re-homing to ensure the reset is issued only once for
each print.
Similarly, do not reset the autodetection when LA is disabled via M900
K0. This can/will be used during a print if different quality settings
are used for different filling roles.
Since the advance factor is computed per-segment in LA15, there's no
need to stop the planner. Allow changing K freely at each segment.
This allows varying quality factors for different filling roles, see:
https://github.com/supermerill/Slic3r/issues/108
During pause/resume/crashdetect or powerpanic K might temporarily be out
of sync when used this way. If this becomes an issue, we might need to
store K for each block, as done for the feedrate.
Move the common checks between filament sensors out of fsensor_update().
Disable the runout check if a saved state is already present (this check
was missing in the PAT9125 variant) as this is currently not supported.
Note that the CHECK_FSENSOR looks completely redundant besides
e_active().
Allow existing gcode using LA10 to transparently take advantage of LA15
by using a simple linear conversion function based on experimental
results with the MK3 implementation of linear advance.
Autodetect LA10 values based on the first M900 instruction contained in
the print. In order to support printing mixed files without resetting
the printer we also reset the autodetection status when starting a new
SD print and/or when explicitly disabling LA.
Since we cannot reliably detect whether a new print is started when
printing via USB, also reset the detection status when homing in G28,
which is generally performed once at each print. Note that this doesn't
clear the previous K value, it only allows a subsequent M900 to provide
LA10 values when printed after a LA15 file.
axis_relative_modes can cleanly handle G90/G91 and M82/M83 without the
need of "relative_mode" entirely.
Change G90/G91 to simply reset all axes according to the requested
state, which avoids to check two variables in get_coordinates(),
fixing the following incorrect handling:
G91 ; all axis relative
M83 ; set extruder absolute
G1 E1 ; should be an absolute move, but still relative
Correctly cleanup the printer state when stopping the current print:
- Disable interrupts while aborting the planner/queue to ensure
new serial commands are not inserted while aborting
- _Always_ call planner_abort_hard() to interrupt any pending move!
- Clear the saved_target, which might be set when calling stop
from within a paused state. Create a new function to clear the
paused state for future use.
- Do not disable/reset the MBL: doing so will destroy the ability to
restart correctly using M999.
Similarly to resume_print_from_ram_and_continue, abort any
planning in mesh_plan_buffer_line already in stop_and_save_print_to_ram
in case it is called for pausing only.
Remove the conflicting and mostly useless card.paused flag (the printing
is either paused, or not) and switch to isPrintPaused only which
accounts for both cases (SD/USB) correctly.
Fix M27/getStatus to show the current real status of the SD print.
Synchronize the queue on M601, as required to precisely pause the print
at the correct instruction.
Alias M25 to M601, which when combined with PR #1899 fixes issue #1614.
Guard against incorrect usage in M601, M602 and M603.
Since the global feedrate can be similarly modified for moves ahead of
time, save the original feedrate in the planner as we do for
gcode_target.
This avoids having to undo feedmultiply (and machine limits!) from
"nominal_speed" as previously done.
Thanks @leptun
Remove incorrect usage of stop_and_save_print combined with the
fsensor_recovert internal instruction which would result in a
broken sequence of events and/or broken stack.
Re-use the now safe stop/recover functions in the same spot
(fsensor_checkpoint_stream) to effectively cut a hole in the current
gcode stream to insert an M600 instruction, which removes all
recursive behavior without the need of extra state variables.
When starting to replay existing USB/SD commands from a recovery state,
an immediate relative move needs to compensate for a previously
interrupted move. This is almost the norm for the E axis.
Instead of saving the relative status of the move (which needs to
account for the world2machine conversion and is not always available on
a chunked move split by MBL) save directly the calculated target
position for the move in the original plan, which is easy to replay.
While handling moves in a recursive plan, such a filament check,
ensure restore_print_from_ram_and_continue unwinds the stack by
aborting early from any call that waits on the planner.
This currently only handles G1 moves, but hard-coded behavior that can
trigger recursive behavior (such as filament change) will probably have
to be checked too.
- Introduce raise_z_above to move Z carefully when the current position
is potentially unknown, using stallguard
- Use raise_z_above for:
* filament loading/unloading clearance
* extruder spacing when preheating (to avoid buildplate marks on PEI)
* before homing to avoid damaging the build plate and to avoid
repeated Z moves as well
Since raise_z_above is conditional, it will only raise when needed.
Calling raise_z_above when the extruder position is unknown and already
at maximum travel is safe and will prevent further vertical moves.
Fix wizard not starting after Factory RESET / All Data on MK25 printer.
This was broken by:
Author: leptun <voinea.dragos.alexandru@gmail.com>
Date: 3 weeks ago (9/12/2019 6:16:31 AM)
Commit hash: 78708903e8
Also update eeprom value
Do not remember CooldownNoWait property set by M190 and M109. If M190 was invoked without parameters, CooldownNoWait property was set if it was previously set by "M109 S" or "M109 S" or printer was after power up. Otherwise CooldownNoWait was not set. Now CooldownNoWait is never set if M190 is invoked without parameters.
Saves 44 B of FLASH memory.
Do not call long_pause recursively!
long_pause() is called before resetting the lcd_command_type. As
long_pause uses st_synchronize() internally, there could be time to
schedule another call to long_pause().
As sdpos_atomic was not updated after printer power up and first power panic recovery, it was equal 0. When the first command from SD card was queued its size on SD card was computed as current SD index position minus sdpos_atomic. This was equal to offset from beginning of the file limited to 16 bit storage type. When next power outage occurred earlier then this command was finished and wiped out of queue, this command size (extraordinarily big) was subtracted from sdpos_atomic and saved to EEPROM. This led to up to 65536 B jump back in file printed after next power panic recovery.
Remove variable CrashDetectMenu. Read this state from EEPROM_CRASH_DET instead in bool lcd_crash_detect_enabled().
Rename crashdet_enable() to lcd_crash_detect_enable() and move it to ultralcd.cpp.
Rename crashdet_disable() to lcd_crash_detect_disable() and move it to ultralcd.cpp.
Rename lcd_crash_mode_set() to crash_mode_switch().
Remove forward function declarations from *.cpp file.
Saves 34B of FLASH and 2B of RAM.
Remove disable_z() call from uvlo_() and uvlo_tiny() power panic interrupt handlers. As historically this function was empty. And in case PSU_Delta macro defined it switches Z trinamic to silent mode, which could take some time and is not needed. Remove alignment to to full step from disable_force_z(), as it is not needed when switching to silent mode.
