Alessandro Ranellucci
010b71e9d4
Improvements to avoid numerical issues in bridge detection and bridge exclusion
2014-04-30 15:16:15 +02:00
Alessandro Ranellucci
4680bbdfe2
Make sure spiral vase mode is not enabled for multi-island layers. #1938
2014-04-30 12:23:07 +02:00
Alessandro Ranellucci
8ded268e7e
Take into account that $layerm->perimeters also contains ExtrusionPath objects. #1991
2014-04-30 10:47:31 +02:00
Alessandro Ranellucci
1667d1826d
Put continuous base flange under pillars support material
2014-04-30 01:51:19 +02:00
Alessandro Ranellucci
1d10cd3da6
Also remove bridged perimeters area from support material
2014-04-30 01:20:18 +02:00
Alessandro Ranellucci
3e3cc4171c
TODO about bridges and support material
2014-04-29 23:40:52 +02:00
Alessandro Ranellucci
ef2296dc8d
Make sure interface and base generation honor the gap between support material and object
2014-04-29 23:29:52 +02:00
Alessandro Ranellucci
ed1c6d1aaa
Removed debugging line
2014-04-29 23:17:01 +02:00
Alessandro Ranellucci
98e40d3fe4
Store width and height in ExtrusionEntity objects for debugging purposes
2014-04-29 23:16:16 +02:00
Petr Ledvina
78a08e0665
Commented out test (breakpoint) line
2014-04-29 22:55:10 +02:00
Alessandro Ranellucci
a31b2e6ca2
Stricter implementation of the overhang detection. Includes unit tests
2014-04-29 19:58:58 +02:00
Alessandro Ranellucci
caf7b3f97e
Prune bridge angles
2014-04-29 18:36:50 +02:00
Alessandro Ranellucci
7a9dec3720
One more change to multi-value placeholders: indices start from 0. #1899
2014-04-29 17:12:00 +02:00
Alessandro Ranellucci
a4b6075600
Fixed regression and ambiguity about multiple-value placeholders like [first_layer_temperature_1]. Includes several unit tests covering regression. #1899
2014-04-29 17:06:31 +02:00
Alessandro Ranellucci
913ab54a2b
Bugfix: gap fill was not inserted in the correct order before leaving island. Includes regression test. #1907
2014-04-29 15:25:14 +02:00
Alessandro Ranellucci
0b0ec7be37
Fixed regression causing bad loading of multi-extruder values in GUI. #1984
2014-04-28 22:31:29 +02:00
Alessandro Ranellucci
f7421053cc
Improvements to bridge angle detection: use coverage test for all cases (including two-sided bridges and C-shaped bridges) and check for all angles equal to directions of bridge sides
2014-04-28 22:15:40 +02:00
Alessandro Ranellucci
24571612c7
Some minor changes to the newly-ported Extruder class
2014-04-28 22:02:34 +02:00
Alessandro Ranellucci
4c330b6c59
Merge pull request #1968 from sapir/extrudercpp
...
Translate Extruder class to C++
2014-04-28 21:45:53 +02:00
Alessandro Ranellucci
2720000a17
New get_trapezoids() implementation. Maybe heavier but it doesn't fail with some versions of GCC like the one provided by Boost.Polygon. #1965
2014-04-28 20:14:20 +02:00
Y. Sapir
ad03a88733
Add xsp wrapper for Pointf class.
2014-04-28 01:13:50 +03:00
Y. Sapir
e005ff32c4
Replace Extruder::config accessor with Perl wrapper, with C++ option accessors.
2014-04-28 00:49:05 +03:00
Y. Sapir
2565d80679
Replace multitude of Extruder fields with querying a PrintConfig object by id.
2014-04-27 23:43:44 +03:00
Y. Sapir
66d23a2416
Convert Extruder object (mostly) to C++ with lots of fields.
2014-04-27 23:42:59 +03:00
Alessandro Ranellucci
2738a304e8
Update credits. Mention Gary Hodgson, Petr Ledvinap, Y. Sapir
2014-04-27 20:04:02 +02:00
Alessandro Ranellucci
ce9cf4d964
Don't put supports under bridges and potential bridges
2014-04-26 17:19:50 +02:00
Alessandro Ranellucci
148c773319
Exclude support from bridged areas
2014-04-26 16:07:43 +02:00
Alessandro Ranellucci
073b7fca1f
One more fix after recent fix to default extrusion width
2014-04-25 20:19:02 +02:00
Alessandro Ranellucci
9ee3868f92
Removed debugging line left
2014-04-25 20:05:08 +02:00
Alessandro Ranellucci
6780e930cb
Update the [timestamp] placeholder(s) at every G-code export. #1957
2014-04-25 19:47:13 +02:00
Alessandro Ranellucci
f7ffc48397
Bump version number
2014-04-25 19:44:04 +02:00
Alessandro Ranellucci
7ac0095018
Fix regression causing default extrusion width to be ignored. #1958
2014-04-25 19:39:27 +02:00
Alessandro Ranellucci
f6897a346a
Fix islands not being ordered efficiently with the logic that completes each of them before moving to the next one (which is now the default behavior). #1137
2014-04-25 19:11:17 +02:00
Alessandro Ranellucci
2a2ba15665
Use a slider for the cutting GUI
2014-04-25 18:36:08 +02:00
Alessandro Ranellucci
8db4913b04
New option for rotating the lower part resulting from the cut so that the flat surface lies on the print bed
2014-04-25 17:50:03 +02:00
Alessandro Ranellucci
4f17c2b7d1
First working implementation of a GUI for cutting
2014-04-25 17:14:39 +02:00
Alessandro Ranellucci
882a98ed44
Initial work for a GUI for the cut feature
2014-04-25 14:54:08 +02:00
Alessandro Ranellucci
fe1691c151
New --cut feature
2014-04-25 10:20:30 +02:00
Alessandro Ranellucci
6201aacf88
New coverage detection for bridges. Includes implementation of ExPolygon::get_trapezoids()
2014-04-24 13:44:39 +02:00
Petr Ledvina
802ebfb0d6
Fix bridge detector
...
Test line direction is changed to reflect 0=east angle system
Test patern rotation direction is reversed - $angle represents infill direction
Angle test is changed to avoid returning negative value (this does happen otherwise - adding increments to $angle
creates ~ 1e-15 rounding error)
2014-04-23 11:35:58 +02:00
Alessandro Ranellucci
3a49dccf69
Bugfix: version check caused crash
2014-04-22 11:59:01 +02:00
Alessandro Ranellucci
c87a21f304
Releasing 1.1.1
2014-04-22 11:20:58 +02:00
Alessandro Ranellucci
9989ebaabd
Refactored the BridgeDetector class to expose a cleaner API and make it stateful
2014-04-22 00:59:14 +02:00
Alessandro Ranellucci
bc101bd93e
Assume bridge angle is stored in radians in infill generation. #1917
2014-04-21 23:21:15 +02:00
Alessandro Ranellucci
f7e8a99078
More tests and related fixes to bridge detection. #1917
2014-04-21 20:44:21 +02:00
Alessandro Ranellucci
7041ebdd22
Workaround for upstream module bug causing command line option parsing for multi-boolean options like retract-layer-change and wipe
2014-04-19 19:14:41 +02:00
Alessandro Ranellucci
5d10ef514f
Workaround wxWidgets not allowing SetValue() inside a EVT_COMBOBOX handler on Windows. #1865
2014-04-19 18:42:52 +02:00
Alessandro Ranellucci
a49e786b04
Handle EVT_TEXT on wxSpinCtrl too
2014-04-19 18:29:40 +02:00
Alessandro Ranellucci
6e6fb427fb
Fixes for the last commit about kill focus. #1873
2014-04-19 18:16:34 +02:00
Alessandro Ranellucci
10a5a061d4
Bugfix: wxWidgets on Windows needs Skip() on kill focus to prevent nasty focus bugs. #1873
2014-04-19 18:05:01 +02:00
Alessandro Ranellucci
a248c98192
Fixed regression when concentric infill was used as solid infill. Includes regression test. #1650
2014-04-19 16:53:37 +02:00
Alessandro Ranellucci
c3bb8a69db
Bugfix: crash when extending an array option by 2+ positions. #1908
2014-04-19 16:38:28 +02:00
Alessandro Ranellucci
f6e99f1467
Bugfix: [filament_preset] was not replaced in filename when using Quick Slice. #1870
2014-04-19 12:10:15 +02:00
Alessandro Ranellucci
1e5dcd8154
Always do one island at time instead of doing that only when avoid_crossing_perimeters is enabled. #1907
2014-04-19 11:57:01 +02:00
Alessandro Ranellucci
f51921a11a
Default extruder wasn't applied to perimeter extruder. Includes regression test. #1868
2014-04-19 11:43:41 +02:00
Alessandro Ranellucci
0c50ab5323
Removed duplicated method added to Slic3r::Line in caf20664cd. #1945
2014-04-19 10:52:12 +02:00
Alessandro Ranellucci
caf20664cd
Bugfix: ExPolygon::contains_line() was called with a Polyline object but didn't throw any error. Thanks ledvinap #1945
2014-04-19 01:26:21 +02:00
Alessandro Ranellucci
62e19469bc
Fixed regression in --infill-only-where-needed. Includes a minimal test suite for such feature. #1871
...
Conflicts:
t/fill.t
2014-04-18 21:48:32 +02:00
Alessandro Ranellucci
15628a90ed
Regression test for numerical issues causing thin gaps between perimeters and infill. #1803
2014-04-18 17:30:35 +02:00
Alessandro Ranellucci
93f4fe05e1
Better logic for gap fill: don't subtract from fill surfaces those gaps that medial axis was unable to fill. Thanks ledvinap for the idea and proof of concept implementation. Includes a tolerance factor for avoiding being too strict when collapsing loops (allow some overlap if that helps avoiding triggering medial axis). #1803
2014-04-15 01:41:40 +02:00
Alessandro Ranellucci
e02d33bbce
Remove weak test. #1803
2014-04-15 00:57:43 +02:00
Alessandro Ranellucci
43ffb7d3e8
Bugfix: sometimes a tiny gap was left between infill and perimeters. Includes regression test. #1803
2014-04-15 00:22:31 +02:00
Alessandro Ranellucci
f9661b02a6
Bugfix in utils/pdf-slices.pl, wrong shift caused slices to be outside the media box
2014-04-11 19:55:15 +02:00
Alessandro Ranellucci
8e5ca0ab76
Fixed a couple typos
2014-04-09 00:36:13 +02:00
Alessandro Ranellucci
627f23d5fe
Make angle increment (i.e. angle resolution) configurable
2014-04-08 16:53:32 +02:00
Alessandro Ranellucci
38f6e3b643
More unit tests for bridge angle detection
2014-04-08 15:18:37 +02:00
Alessandro Ranellucci
9be57f750d
Some fixes to bridge direction detection. Includes regression tests
2014-04-08 14:51:55 +02:00
Alessandro Ranellucci
23e6abff49
Added first unit test for bridge direction
2014-04-08 13:08:42 +02:00
Alessandro Ranellucci
119778caa9
Refactoring: move bridge angle detection to a separate class for easier unit testing
2014-04-07 23:18:11 +02:00
Alessandro Ranellucci
93a7d87fc6
Bugfix: pillars support material crashed when no overhangs were detected
2014-04-07 16:59:22 +02:00
Alessandro Ranellucci
1c020eda78
Merge pull request #1911 from sapir/speed
...
Rewriting the extrusion path gcode generation in C++
2014-04-07 09:38:21 +02:00
Alessandro Ranellucci
33ade1328f
Fix regression causing profile names to be listed in random order. #1864
2014-04-06 22:45:40 +02:00
Alessandro Ranellucci
e4709068b9
Some more unit tests for arc fitting
2014-04-06 22:32:53 +02:00
Alessandro Ranellucci
1d35701f99
Incomplete work on arc fitting. Results are still incomplete. More unit tests are needed
2014-04-06 22:10:34 +02:00
Alessandro Ranellucci
c7a96a3113
Merge pull request #1881 from sapir/master
...
Disable some calls to on_presets_changed to speed up switching profiles
2014-04-06 12:52:05 +02:00
Alessandro Ranellucci
20df1023a6
Fixed broken command line scaling. Regression test was in previous commit. #1889
2014-04-05 11:22:05 +02:00
Alessandro Ranellucci
e9e23119fc
Failing test for broken command line scaling. #1889
2014-04-05 11:21:26 +02:00
Alessandro Ranellucci
fc4ac5ded4
Re-enable the threads config option. #1882
2014-04-05 10:58:03 +02:00
Alessandro Ranellucci
d6d6a51e0d
Fix for incomplete extrusion on solid surfaces
2014-04-05 10:54:24 +02:00
Alessandro Ranellucci
6f3844c1ba
Fix crash when using multiple skirts with a single, non-zero, extruder. Includes regression test
2014-04-05 10:09:05 +02:00
Alessandro Ranellucci
a6dd68a2a6
Bugfix: crash when setting number of extruders. #1876
2014-04-05 09:54:43 +02:00
Alessandro Ranellucci
f308a46cd5
Bump version number
2014-04-02 20:25:05 +02:00
Alessandro Ranellucci
45559f87f3
Save the vector used for aligning object volumes to origin and apply it to additional parts added from the object part panel in order to make them coincide
2014-04-02 20:23:26 +02:00
Y. Sapir
4deeff995a
Move extrusion path gcode generation to C++ for speed.
2014-04-01 21:11:43 +03:00
Y. Sapir
f56206cac3
Precache gcode_comments flag before path loop.
2014-04-01 21:11:43 +03:00
Y. Sapir
9f71ea15cf
Precompute X and Y offsets before path loop.
2014-04-01 21:11:43 +03:00
Y. Sapir
576d02a20d
Make set_dirty ignore changes that don't do anything.
2014-03-30 00:23:35 +03:00
Y. Sapir
09d7d9b034
Remove call to on_presets_changed from Tab Page's on_change.
...
(set_dirty is called which handles it anyway.)
2014-03-30 00:21:57 +03:00
Alessandro Ranellucci
017158c877
Update year to 2014 in about dialog
2014-03-27 15:33:17 +01:00
Alessandro Ranellucci
f41480ab8f
Releasing 1.1.0
2014-03-27 11:15:39 +01:00
Alessandro Ranellucci
071097d3f1
Fix extruder assignment and tests
2014-03-27 00:01:33 +01:00
Alessandro Ranellucci
10bf334a58
Added one more failing test to address bad option priority hierarchy
2014-03-26 19:42:01 +01:00
Alessandro Ranellucci
0ff33f47f1
Fix the extruder override logic. All role-based extruder options now default to 0, meaning no override is defined and the default (inherited) extruder is used. The default extruder option does not use the shortcut logic anymore (it was thus moved to be a CLI-specific logic)
2014-03-26 00:08:15 +01:00
Alessandro Ranellucci
2e6213fea6
Prevent crash when changing number of extruders
2014-03-25 19:21:44 +01:00
Alessandro Ranellucci
d1bb69434e
Handle non existing STL files gracefully
2014-03-25 19:06:51 +01:00
Alessandro Ranellucci
9b2445f0f5
Assign default material to OBJ files too
2014-03-25 15:39:13 +01:00
Alessandro Ranellucci
25191bd405
Prevent circular event handlers on Windows. #1856
2014-03-25 15:30:56 +01:00
Alessandro Ranellucci
f6f1517f58
Bugfix: the Add button in plater wasn't working anymore. #1856
2014-03-25 15:07:21 +01:00
Alessandro Ranellucci
7e3425d433
Bugfix: wizard wasn't run when user supplied an existing empty directory as --datadir
2014-03-25 14:07:03 +01:00
Alessandro Ranellucci
fed8783e30
New commands for exporting/importing full config bundles. Useful for printer vendors. #1365
2014-03-25 14:04:01 +01:00
Alessandro Ranellucci
c98c992b4d
Revert wrong fix, applied because of bad understanding of the issue about deserialization of extruder_offset = 0x0
2014-03-25 01:20:46 +01:00
Alessandro Ranellucci
432a87e73d
New option for forcing the generation of interface shells. #1847
2014-03-25 01:11:28 +01:00
Alessandro Ranellucci
6feff7fe53
Test that stacked cubes with distinct extruders don't generate any internal interface shells. #1847
2014-03-24 23:44:47 +01:00
Alessandro Ranellucci
72a6848f1b
Fixed regression causing wrong relative positions of objects after splitting in plater. #1758
2014-03-24 21:42:38 +01:00
Alessandro Ranellucci
5ce4de0544
Bugfix: wrong inwards moves were calculated for 2+ copies because ExtrusionLoop objects were modified in place. Includes regression test. #1842
2014-03-24 20:01:14 +01:00
Alessandro Ranellucci
b4ac63d749
Error in previous commit: Bugfix: prevent crash when user entered Unicode characters in notes. #1590
2014-03-24 17:52:50 +01:00
Alessandro Ranellucci
ce984ef78c
Revert "Error in previous commit: Bugfix: prevent crash when user entered Unicode characters in notes. #1590 "
...
This reverts commit e355e521d4
2014-03-24 17:52:14 +01:00
Alessandro Ranellucci
e355e521d4
Error in previous commit: Bugfix: prevent crash when user entered Unicode characters in notes. #1590
2014-03-24 17:02:25 +01:00
Alessandro Ranellucci
d9d2f3b3ab
Bugfix: prevent crash when user entered Unicode characters in notes. #1590
2014-03-24 16:37:20 +01:00
Alessandro Ranellucci
7a58457add
Prevent GUI from crashing when invalid values were written in numeric fields. Includes basic validation. #1709
2014-03-24 01:07:30 +01:00
Alessandro Ranellucci
67f3e9962b
Prevent user from saving a preset with the "- default -" name. #1717
2014-03-23 21:40:45 +01:00
Alessandro Ranellucci
5d3c8575c5
Bugfix: holes were not sorted using the nearest-neighbor search, resulting in inefficient paths. #1785
2014-03-23 19:55:31 +01:00
Alessandro Ranellucci
ea3266c6e9
Fix modifiers
2014-03-23 16:56:41 +01:00
Alessandro Ranellucci
fec41d6dfd
Update plater and print upon changing object parts and their settings
2014-03-23 16:45:55 +01:00
Alessandro Ranellucci
67ef3f1799
Assign a default extruder for newly added parts too
2014-03-23 15:25:26 +01:00
Alessandro Ranellucci
d75417601e
Make the override panel prettier and prevent the default extruder setting from being deleted since it can't be readded manually
2014-03-23 15:18:08 +01:00
Alessandro Ranellucci
bf8c388568
Use a popup menu for part settings
2014-03-23 13:46:05 +01:00
Alessandro Ranellucci
21e6de0e59
Only expand shortcut options in StaticConfig objects. This way we can keep a default extruder value in the parts panel
2014-03-22 20:12:54 +01:00
Alessandro Ranellucci
61db9530d9
Fix AMF settings not being correctly propagated to plater and parts panel
2014-03-22 18:02:58 +01:00
Alessandro Ranellucci
6a157c22c2
Fixed minor fatal error
2014-03-22 17:44:42 +01:00
Alessandro Ranellucci
f71ac8cd65
Merge the Object Settings tab into the Parts tab
2014-03-22 17:41:14 +01:00
Alessandro Ranellucci
b5b735c988
ComboBox for fill density values
2014-03-22 17:01:48 +01:00
Alessandro Ranellucci
7421a7bf63
Turn fill_density into percentage
2014-03-22 16:23:33 +01:00
Alessandro Ranellucci
30aa255bb5
Correctly disable and reset the override settings panel
2014-03-21 22:15:33 +01:00
Alessandro Ranellucci
bf352de224
Replaced icon for modifier meshes and fixed delete button not being disabled when no part was selected
2014-03-21 22:06:47 +01:00
Alessandro Ranellucci
34f1511e0c
Better fix for non-global options not being replaced in filename placeholders. Includes refactoring and a new PlaceholderParser class. Also includes regression tests. #1831
2014-03-17 00:39:07 +01:00
Alessandro Ranellucci
bc054e613c
Fix regression causing non-global config options to be ignored when replacing placeholders in output filename format. #1831
2014-03-15 20:45:10 +01:00
Alessandro Ranellucci
96c2c21707
Minor bugfix for preventing wrong extruder numbers from being assigned
2014-03-15 18:24:56 +01:00
Alessandro Ranellucci
52de292a48
Fixed wrong refactoring of perimeter tree traversal. #1832
2014-03-15 02:16:04 +01:00
Alessandro Ranellucci
b71d28bd5a
Fix minor error and update MANIFEST
2014-03-11 19:19:34 +01:00
Alessandro Ranellucci
f344426873
Better linear gap fill, now with adaptive extrusion width
2014-03-11 19:08:14 +01:00
Alessandro Ranellucci
98b7ae0022
Initial implementation of linear gap fill
2014-03-09 21:26:03 +01:00
Alessandro Ranellucci
7f5442265e
Include thin walls in general top-level perimeter sorting to get more efficient paths
2014-03-09 20:19:30 +01:00
Alessandro Ranellucci
2a73ab988f
Recursive pruning. Some more unit tests
2014-03-09 17:46:02 +01:00
Alessandro Ranellucci
04d80ca392
Some improvements to pruning and some additions here and there
2014-03-05 18:43:01 +01:00
Alessandro Ranellucci
c2ed6090d3
Fix the max width supplied to medial axis code: it's up to two extrusions
2014-03-05 00:53:51 +01:00
Alessandro Ranellucci
4a894b1e20
Add safety offset to thin wall regions to prevent overlapping geometry and corrupt Voronoi diagram
2014-03-05 00:45:17 +01:00
Alessandro Ranellucci
3c77b301a7
Promising approach to medial axis pruning
2014-03-04 23:33:13 +01:00
Alessandro Ranellucci
8644440070
Minor improvements to SVG debug output for medial axis
2014-03-03 14:20:15 +01:00
Alessandro Ranellucci
eadffe4a9e
Merge branch 'master' into boost-medialaxis
...
Conflicts:
lib/Slic3r/Layer/Region.pm
xs/src/ExPolygon.cpp
xs/src/Point.cpp
xs/src/Point.hpp
xs/src/TriangleMesh.cpp
xs/t/01_trianglemesh.t
2014-03-02 22:36:20 +01:00
Alessandro Ranellucci
0f9e143ba1
Removed debugging line
2014-03-02 00:44:16 +01:00
Alessandro Ranellucci
2295d48947
Better pruning of thin walls to avoid unwanted extra extrusions. Includes regression test. #1794
...
Conflicts:
lib/Slic3r/Layer/Region.pm
2014-03-02 00:31:17 +01:00
Alessandro Ranellucci
a344d68257
Use bridge speed for first solid layer above sparse infill. Includes unit test. #1792
2014-03-01 20:35:44 +01:00
Mark Hindess
59ebdebf72
Revert "Fix crash reported by Simooon on #Slic3r."
...
It turns out this helped on the version of stable I was using
but not on master.
This reverts commit 8df6e2d930
2014-02-16 14:00:28 +00:00
Mark Hindess
8df6e2d930
Fix crash reported by Simooon on #Slic3r.
...
Error was:
Argument "" isn't numeric in subroutine entry at
lib/Slic3r/GUI/OptionsGroup.pm line 392
2014-02-16 12:05:01 +00:00
Alessandro Ranellucci
e837183327
Fixed regression when using --infill-only-where-needed. Includes regression test. #1721
2014-02-16 12:48:07 +01:00
Alessandro Ranellucci
878deb8183
Write material config to AMF files. Remove the old Materials tab. Update custom settings when a part is selected
2014-02-15 00:36:52 +01:00
Alessandro Ranellucci
691db31da0
Some incomplete work for per-region config
2014-02-14 22:26:00 +01:00
Alessandro Ranellucci
2e7b29fbdd
Minor layout changes to the Parts editor
2014-02-14 22:25:59 +01:00
Alessandro Ranellucci
bf307371f4
Use a plain list instead of a tree to display object parts
2014-02-14 22:25:59 +01:00
Alessandro Ranellucci
df508551d0
Refresh plater canvas when switching presets
2014-02-14 22:25:58 +01:00
Alessandro Ranellucci
4c650a6d80
Fix regression about percent extrusion width not being validated. Includes regression test
2014-02-13 18:42:49 +01:00
Alessandro Ranellucci
49d290accf
Fixed spiral vase regressions. Includes regression tests. #1773
2014-02-13 16:11:12 +01:00
Alessandro Ranellucci
0060873f1c
Regression test and incomplete fix for bug affecting wrong spiral vase output. #1773
...
Conflicts:
lib/Slic3r/GCode/Layer.pm
2014-02-13 16:11:02 +01:00
Alessandro Ranellucci
94cb298eec
Make OpenGL optional for the new parts dialog. #1731
2014-02-11 01:09:10 +01:00
Alessandro Ranellucci
b961849c38
Bugfix: crashing when concentric infill produced very narrow loops. #1740
...
Conflicts:
lib/Slic3r/Fill/Concentric.pm
2014-02-10 16:05:40 +01:00
Alessandro Ranellucci
3d483722c6
Perform additional checks before merging solid surfaces (i.e. take flow and fill pattern into account)
2014-02-10 13:19:44 +01:00
Alessandro Ranellucci
634ccb33ab
Fix regression in Config->setenv affecting post-processing scripts. Includes regression test
2014-02-09 23:14:32 +01:00
Alessandro Ranellucci
bba69ed22f
Merge pull request #1742 from treygreer/master
...
fixed simple config load bug
2014-02-07 02:12:42 +01:00
Alessandro Ranellucci
ffc891d885
Bugfix: when processing with fill_density = 0, top/bottom solid shells were missing regions thinner than 3 * extrusion width. Includes regression test. #1602
...
Conflicts:
lib/Slic3r/Print/Object.pm
t/fill.t
2014-02-07 02:07:21 +01:00
Trey Greer
0dba3dee58
fixed simple config load bug
2014-01-28 19:05:20 -05:00
Alessandro Ranellucci
42519174cd
New erase() method for DynamicConfig objects
2014-01-22 21:15:19 +01:00
Alessandro Ranellucci
b5b8fb606f
Basic functionality of the Parts tab is complete
2014-01-22 21:15:19 +01:00
Alessandro Ranellucci
7387e60706
More incomplete work
2014-01-22 21:15:19 +01:00
Alessandro Ranellucci
b20caa4e31
Completed parts visualization with highlighting
2014-01-22 21:15:19 +01:00
Alessandro Ranellucci
3f4f27fa5d
Some incomplete work for interactive part editor
2014-01-22 21:15:18 +01:00
Alessandro Ranellucci
fd43ada293
Remove duplicated "Generating skirt" status message
2014-01-18 16:36:13 +01:00
Alessandro Ranellucci
90194ee581
Fix overflow in Point::ccw() affecting convex hull generation. Includes regression test
2014-01-17 14:49:51 +01:00
Alessandro Ranellucci
86f91bb3c4
New TriangleMeshSlicer::cut() method
2014-01-16 11:25:26 +01:00
Alessandro Ranellucci
dfd9bc8958
Bugfix: prevent fatal error in the rare case that no bridge anchors are found. #1607
2014-01-15 00:24:37 +01:00
Alessandro Ranellucci
a40556ab56
Repair meshes after splitting
2014-01-14 22:06:28 +01:00
Alessandro Ranellucci
79a2bab261
Revert stupid change that broke plater and provide the correct fix for --info
2014-01-14 21:46:39 +01:00
Alessandro Ranellucci
28a39f0275
Fix garbage collection of recently added classes
2014-01-14 20:11:08 +01:00
Alessandro Ranellucci
51af10da4f
Some fixes to config API
2014-01-12 12:35:13 +01:00
Alessandro Ranellucci
12b661e877
Adapt skirt logic to the potential situation of objects with different layer heights
2014-01-12 11:06:21 +01:00
Alessandro Ranellucci
a51743a8c1
Bugfix: lack of strong type checking when passing arrayref objects to XS caused random lack of infill. Now added strong type checking for all XS entities. Also fixes a potential issue with bridges caused by the same error. #1652
...
Conflicts:
lib/Slic3r/Layer/Region.pm
2014-01-12 00:54:10 +01:00
Alessandro Ranellucci
e68cbede6e
Add scale rotate duplicate_grid to @Ignore and fix @Ignore which was ignored
2014-01-11 23:46:20 +01:00
Alessandro Ranellucci
89d3dbaa5a
Bugfix: incorrect number of raft layers was generated when too few were requested. #1678
...
Conflicts:
lib/Slic3r/Print/Object.pm
2014-01-11 23:26:48 +01:00
Alessandro Ranellucci
e7349622a2
Removed dependency on Storable; some fixes in Build.PL. #1693
2014-01-11 21:46:22 +01:00
Alessandro Ranellucci
c99b9d91db
Fix bug in regression infill causing bad clipping at very low layer heights. Includes regression test. #1669
...
Conflicts:
lib/Slic3r/Fill/Rectilinear.pm
2014-01-11 21:34:26 +01:00
Alessandro Ranellucci
3084876e60
Fixed --info
2014-01-11 18:05:14 +01:00
Alessandro Ranellucci
ea173cf815
Bugfix: ambiguous semantics of the layers_count() method caused M73 to go beyond 100%. #1670
...
Conflicts:
lib/Slic3r/GCode.pm
lib/Slic3r/Print.pm
lib/Slic3r/Print/Object.pm
2014-01-11 17:40:09 +01:00
Alessandro Ranellucci
c0a74780cb
The ratio_over parameter was missing in the definition of first_layer_extrusion_width
2014-01-11 14:48:13 +01:00
Alessandro Ranellucci
ed3a6349c7
Adapt the new gcode.t test to master (and subtract final retraction from used filament length)
2014-01-11 14:42:31 +01:00
Alessandro Ranellucci
9515acf527
Put a hard limit on manually configured extrusion widths (10 * the largest nozzle diameter configured) to prevent confusion when a bad value is entered. #1691
...
Conflicts:
lib/Slic3r/Config.pm
2014-01-11 14:32:42 +01:00
Alessandro Ranellucci
7b0decbeb1
Finished implementing Boost.Polygon medial axis. Some cleanup needed
2014-01-10 16:18:55 +01:00
Alessandro Ranellucci
07a4c37c4c
Semi-working Boost.Polygon medial axis. Hangs after perimeters, though. Needs pruning and chaining
2014-01-10 11:47:16 +01:00
Alessandro Ranellucci
bf91f3096a
Incomplete work for using Boost.Polygon to compute medial axis
2014-01-09 17:26:39 +01:00
Alessandro Ranellucci
11f065ca5e
New object dialog tab with list of materials and volumes
2014-01-08 19:36:41 +01:00
Alessandro Ranellucci
6da98a6ecc
Fix GUI
2014-01-07 19:08:37 +01:00
Alessandro Ranellucci
c8a48b4527
Implement modifier volumes and port _merge_loops() to XS
2014-01-07 15:40:38 +01:00
Alessandro Ranellucci
b17d06f9d1
Finished porting BoundingBox to XS
2014-01-07 12:48:09 +01:00
Alessandro Ranellucci
9c0a6a79d3
Incomplete work for porting BoundingBox to XS
2014-01-06 18:29:10 +01:00
Alessandro Ranellucci
3e93a14912
New support material pattern: pillars!
2014-01-05 16:51:16 +01:00
Alessandro Ranellucci
499b34dea1
Catch any click inside thumbnail's contour for easier selection of thin-walled objects
2014-01-05 15:02:12 +01:00
Alessandro Ranellucci
0bdea60b53
Merge branch 'region-config'
...
Conflicts:
lib/Slic3r/Format/AMF/Parser.pm
2014-01-05 14:59:36 +01:00
Alessandro Ranellucci
2754ddf215
Fix positioning of loded AMF plates
2014-01-05 14:04:32 +01:00
Alessandro Ranellucci
036badf932
Ported Flow to XS
2014-01-05 13:16:13 +01:00
Alessandro Ranellucci
87342d324c
Fix typo
2014-01-05 01:25:39 +01:00
Alessandro Ranellucci
4e76a9e4c9
Parse options from AMF metadata
2014-01-05 01:24:31 +01:00
Alessandro Ranellucci
07b9b12475
Make tests pass
2014-01-05 00:36:33 +01:00
Alessandro Ranellucci
a2cbb261cb
More work for refactoring Flow/Extruder
2014-01-03 20:02:00 +01:00
Alessandro Ranellucci
8ed738d3f7
More incomplete work for Flow/Extruder refactoring
2014-01-03 18:27:46 +01:00
Alessandro Ranellucci
52ce6e4a7b
Some initial work for refactoring Print->extruders
2014-01-03 10:44:36 +01:00
Alessandro Ranellucci
b9793b3f12
Moved first_layer_extrusion_width to PrintConfig
2014-01-03 00:34:30 +01:00
Alessandro Ranellucci
81663215c5
Adapt plater to the new split config
2014-01-02 22:06:58 +01:00
Alessandro Ranellucci
bfa2ee2770
Remove scale, rotate, duplicate, duplicate_grid from config (but leave them in CLI)
2014-01-02 18:01:21 +01:00
Alessandro Ranellucci
385e0e0974
Refactoring: new Slic3r::Print::Simple class for non-interactive slicing (used in CLI and Quick Slice)
2014-01-02 17:54:18 +01:00
Alessandro Ranellucci
5bf0942f45
Satisfy test suite and CLI
2014-01-02 17:24:23 +01:00
Alessandro Ranellucci
e2f1040a76
More work
2014-01-02 10:44:54 +01:00
Alessandro Ranellucci
0883d0f4eb
More work here and there
2014-01-01 17:29:15 +01:00
Alessandro Ranellucci
83326845dd
More incomplete work
2013-12-31 14:33:03 +01:00
Alessandro Ranellucci
d29e341a8b
Parse options from AMF metadata
2013-12-30 19:00:32 +01:00
Alessandro Ranellucci
beb1baa096
Incomplete work for refactoring regions and flows
2013-12-30 18:28:41 +01:00
Alessandro Ranellucci
ca2952060d
Draw more detailed thumbnails in plater and turn cursor to hand also when moving inside holes (otherwise objects with thin walls would not be easy to select)
2013-12-29 01:28:06 +01:00
Alessandro Ranellucci
13d7b39072
Fix random crashes on 32-bit. Thank you Valgrind
2013-12-28 15:37:04 +01:00
Alessandro Ranellucci
57e4e5c8e1
One more fix for ooze_prevention and skirt_height == -1
2013-12-24 15:33:54 +01:00
Alessandro Ranellucci
f9d38f6655
Allow value -1 for skirt_height with the meaning of: as tall as the object. This might fix an overflow on 32-bit systems when ooze_prevention is enabled
2013-12-24 15:16:10 +01:00
Alessandro Ranellucci
bd133d9434
Update Clipper to 6.1.2
2013-12-24 12:40:46 +01:00
Alessandro Ranellucci
1a690589a8
Satisfy test suite
2013-12-24 12:03:30 +01:00
Alessandro Ranellucci
2956c1a2e5
More work for removing references to $Slic3r::Config
2013-12-24 11:58:36 +01:00
Alessandro Ranellucci
1157a7f859
Remove package variable $Slic3r::Config
2013-12-24 11:29:31 +01:00
Alessandro Ranellucci
7ddf4f3ddf
Fixes to complete_objects to make t/gcode.t pass
2013-12-24 01:13:02 +01:00
Alessandro Ranellucci
c5ead0f2a6
Fixes to Config and plater; also refactored the arrange() code
2013-12-24 00:30:51 +01:00
Alessandro Ranellucci
87c5427010
Fixed regression causing incomplete gap fill when all configured perimeters were successfully generated. #1589
2013-12-23 21:23:26 +01:00
Alessandro Ranellucci
7389bf3953
Partially revert cacbaa7319: no need for it in master branch
2013-12-23 20:40:44 +01:00
Alessandro Ranellucci
cacbaa7319
Fix regression causing thin walls to come out as zigzag paths. #1573 #1575
2013-12-23 20:37:46 +01:00
Alessandro Ranellucci
20f1f3d2b4
Fix regression preventing raft from being generated for the entire object footprint. #1614 #1567
2013-12-23 20:31:50 +01:00
Alessandro Ranellucci
fc5aac0ff6
Bugfix: fan wasn't turned on for bridges when vibration limit or another internal post-processor was enabled. Includes regression test. #1533
2013-12-23 01:19:53 +01:00
Alessandro Ranellucci
4f58a1c401
Rewrite avoid_crossing_perimeters() to fix a regression and get better performance by choosing regular points along contours. #1531
...
Conflicts:
lib/Slic3r/GCode/MotionPlanner.pm
2013-12-22 19:07:07 +01:00
Alessandro Ranellucci
ab25cc4940
Merge branch 'xs-config'
...
Conflicts:
lib/Slic3r/Config.pm
xs/MANIFEST
2013-12-22 01:41:55 +01:00
Alessandro Ranellucci
c0070a8d54
Satisfy test suite with new XS based config
2013-12-22 01:38:10 +01:00
Alessandro Ranellucci
9fb62e671f
Adapt GUI to new XS Config
2013-12-22 01:27:09 +01:00
Alessandro Ranellucci
4515d90052
Finished porting Config and option definition to XS
2013-12-22 00:39:03 +01:00
Alessandro Ranellucci
9836e963a5
Incomplete work for adapting the application to the new XS-based Config
2013-12-21 21:06:45 +01:00
Alessandro Ranellucci
1b9079ffbe
Merge branch 'xs-model'
2013-12-20 01:41:13 +01:00
Alessandro Ranellucci
1cee992604
Temporarily disabled step-based slicing
2013-12-20 01:38:00 +01:00
Alessandro Ranellucci
a6a6a6888b
Ported Slic3r::Print::State to XS
2013-12-20 01:36:42 +01:00
Alessandro Ranellucci
d2295cdf70
New Slic3r::Print::State class
2013-12-19 18:54:24 +01:00
Alessandro Ranellucci
685e8e4dfa
More work for step-based slicing
2013-12-19 15:23:10 +01:00
Alessandro Ranellucci
5280b05ebb
Initial work for step refactoring
2013-12-19 12:11:02 +01:00
Alessandro Ranellucci
38ea5f79d7
Merge branch 'xs-model'
2013-12-18 19:20:23 +01:00
Alessandro Ranellucci
266673213d
New option for turning autocentering off. #404
2013-12-18 19:11:20 +01:00
Alessandro Ranellucci
15235699e4
Completed adapting plater behavior to new Print object API
2013-12-18 18:54:11 +01:00
Alessandro Ranellucci
916a0a0e58
Fix compilation and test suite
2013-12-18 16:34:31 +01:00
Alessandro Ranellucci
a12b1765d6
Fixed wrong commit f495136. Thanks pdbogen for the report. #1623
2013-12-18 10:21:17 +01:00
Alessandro Ranellucci
0591eecab7
Lazy mesh generation so that we only keep it in model object
2013-12-18 00:13:41 +01:00
Alessandro Ranellucci
f4951367ea
Fixed fatal error about missing method thin_walls(). #1607 #1615
2013-12-17 16:17:15 +01:00
Alessandro Ranellucci
e4c9171890
Handle read_from_file() exceptions in GUI. #1619
2013-12-17 16:14:00 +01:00
Alessandro Ranellucci
94743d3af0
Handle read_from_file() exceptions in GUI. #1619
2013-12-17 16:11:42 +01:00
Alessandro Ranellucci
2d045d1f39
Removed extra line
2013-12-17 16:01:25 +01:00
Alessandro Ranellucci
02df73c94b
More refactoring to clean up the Print object API
2013-12-16 00:54:59 +01:00
Alessandro Ranellucci
d3171b1eea
More work for updating the embedded Print object when Model is changed in plater
2013-12-16 00:36:53 +01:00
Alessandro Ranellucci
fcbd62f07c
Finished updating plater to the new centering logic
2013-12-15 23:50:05 +01:00
Alessandro Ranellucci
4993b12799
Some initial work for adapting plater to the new centering workflow
2013-12-15 18:00:44 +01:00
Alessandro Ranellucci
250608aa52
Move centering outside the Print object
2013-12-15 16:17:12 +01:00
Alessandro Ranellucci
2eff7c238e
Some initial work for stateful Print object
2013-12-13 14:02:01 +01:00
Alessandro Ranellucci
14c97978c7
Use 0,0 for default instance
2013-12-13 12:24:23 +01:00
Alessandro Ranellucci
21ca1901c1
Merge branch 'xs-model'
...
Conflicts:
lib/Slic3r/Model.pm
2013-12-13 12:22:17 +01:00
Alessandro Ranellucci
5470fbbebc
Make quick_slice() work with new model handling
2013-12-13 12:18:30 +01:00
Alessandro Ranellucci
0e8a0ef1ca
Refactoring. Use Model class for representing the plate in GUI
2013-12-12 20:19:33 +01:00
Alessandro Ranellucci
f55e057504
More work for refactoring add_model() to add_model_object(). Tests pass
2013-12-09 01:12:37 +01:00
Alessandro Ranellucci
a02ce3257e
Merge branch 'stable'
2013-12-07 21:03:57 +01:00
Alessandro Ranellucci
0afee63e84
Fixed regression in object placement in STL export. #1552
2013-12-07 21:03:10 +01:00
Alessandro Ranellucci
361ca1568a
Raise version number in master branch
2013-12-07 18:25:35 +01:00
Alessandro Ranellucci
12db58c9d0
Merge branch 'stable'
2013-12-07 14:54:07 +01:00
Alessandro Ranellucci
00e8ba4781
Fix regression causing complete_objects to skip Z moves after first object is complete. Includes regression test. #1582 #1541
2013-12-07 14:52:59 +01:00
Alessandro Ranellucci
0339d5423d
Merge branch 'master' into xs-model
2013-12-06 22:48:42 +01:00
Alessandro Ranellucci
f4d12b5930
Don't return the cached bounding box but clone it
2013-12-06 22:48:12 +01:00
Alessandro Ranellucci
72fe6d903c
Don't return the cached bounding box but clone it
2013-12-06 19:34:50 +01:00
Alessandro Ranellucci
7871673bf6
Initial work for new model handling
2013-11-27 12:18:24 +01:00
Alessandro Ranellucci
57fd6ad563
Removed dependency on ->object from Region.pm
2013-11-26 18:46:48 +01:00
Alessandro Ranellucci
bd8c430afd
Merge branch 'stable'
...
Conflicts:
lib/Slic3r/Geometry/Clipper.pm
lib/Slic3r/Layer/Region.pm
2013-11-24 22:48:31 +01:00
Alessandro Ranellucci
3fca0956bc
Adapt plater to new convex hull
2013-11-24 22:42:52 +01:00
Alessandro Ranellucci
bed1625d6b
Split objects could not be repositioned in plater. 3D preview and stats were not available too. #1543
2013-11-24 14:28:17 +01:00
Alessandro Ranellucci
22605418ba
Removed recursion warning in brim
2013-11-24 13:08:13 +01:00
Alessandro Ranellucci
387df3b900
Fix regression causing toolchange_gcode to crash Slic3r. Includes regression test. #1545
2013-11-24 13:04:16 +01:00
Alessandro Ranellucci
5217bc370a
Fix regression causing retraction restarts to ignore extrusion_axis. Includes regression test. #1547
2013-11-24 12:37:36 +01:00
Alessandro Ranellucci
9cf138574c
New TriangleMesh::convex_hull()
2013-11-24 01:15:52 +01:00
Alessandro Ranellucci
a29eeb7789
Fix t/geometry.t
2013-11-24 00:59:45 +01:00
Alessandro Ranellucci
a93c862338
Ported traverse_pt() to XS
2013-11-23 23:21:59 +01:00
Alessandro Ranellucci
b47b8ee34f
Adapt new code to contains_point()
2013-11-23 22:45:17 +01:00
Alessandro Ranellucci
fc4483d09c
Do perimeters one island at time instead of doing all holes before all contours
2013-11-23 22:45:00 +01:00
Alessandro Ranellucci
97c65bac90
Do perimeters one island at time instead of doing all holes before all contours
2013-11-23 22:43:30 +01:00
Alessandro Ranellucci
30297ee4dc
Removed chained_path_items()
2013-11-23 21:47:33 +01:00
Alessandro Ranellucci
0045f84ed2
Removed chained_path_points()
2013-11-23 21:42:01 +01:00
Alessandro Ranellucci
0516aac715
Ported chained_path() to XS
2013-11-23 21:39:05 +01:00
Alessandro Ranellucci
4d5d003ba7
Ported horizontal_projection() to XS
2013-11-23 19:41:40 +01:00
Alessandro Ranellucci
e75dbf37fa
Never scale TriangleMesh objects
2013-11-23 19:25:33 +01:00
Alessandro Ranellucci
46e3b3180e
Ported Surface->offset() to XS
2013-11-23 18:29:25 +01:00
Alessandro Ranellucci
a331f4d27a
Finished porting group() to XS
2013-11-23 18:15:59 +01:00
Alessandro Ranellucci
878d587196
Ported is_solid() and is_bridge() to XS. Also ported (but not used yet) group() to SurfaceCollection::group()
2013-11-23 00:07:04 +01:00
Alessandro Ranellucci
de9d5403e8
Finished porting convex_hull() to XS and removed dependency on Math::ConvexHull::MonotoneChain
2013-11-22 22:48:07 +01:00
Alessandro Ranellucci
4577f0725c
Incomplete work for XS-based convex_hull
2013-11-22 21:43:35 +01:00
Alessandro Ranellucci
a950fbe0c2
Removed more unused functions and fixed tests
2013-11-22 16:19:15 +01:00
Alessandro Ranellucci
132d170f73
Ported simplify() to XS and removed dependency on Boost::Geometry::Utils
2013-11-22 16:01:50 +01:00
Alessandro Ranellucci
df8d889481
More unfinished work
2013-11-22 02:16:10 +01:00
Alessandro Ranellucci
518798beb3
Incomplete work for porting simplify() to XS
2013-11-21 20:25:24 +01:00
Alessandro Ranellucci
7475762a27
Remove residual uses of Boost for line clipping
2013-11-21 18:47:25 +01:00
Alessandro Ranellucci
3aef663f7f
Removed clip_with_polygon() and clip_with_expolygon()
2013-11-21 18:16:03 +01:00
Alessandro Ranellucci
ac88fbcbb0
Ported clip_end(), length(), is_perimeter(), is_fill(), is_bridge() to XS
2013-11-21 18:03:40 +01:00
Alessandro Ranellucci
761f261a68
Ported intersect_expolygons() and subtract_expolygons() to XS
2013-11-21 17:53:50 +01:00
Alessandro Ranellucci
5f81292f3f
Ported encloses_point() to XS and renamed to contains_point()
2013-11-21 16:21:42 +01:00
Alessandro Ranellucci
a225a8b2ef
Ported contains_line() to XS
2013-11-21 15:12:06 +01:00
Alessandro Ranellucci
bd62de7653
Renamed encloses_line() to contains_line() and implemented it using diff_pl()
2013-11-21 14:35:28 +01:00
Alessandro Ranellucci
3025c77675
Use Clipper for line clipping
2013-11-21 14:15:38 +01:00
Alessandro Ranellucci
c5f7318fc9
Removed debugging statement
2013-11-20 15:38:51 +01:00
Alessandro Ranellucci
50c0081d25
Update Clipper to 6.0.0
2013-11-20 11:35:58 +01:00
Alessandro Ranellucci
d49052779f
Remove useless code (thin walls and gaps are detected by the same logic now, so no need for additional checks)
2013-11-19 15:55:22 +01:00
Alessandro Ranellucci
b1ca0f30f2
Version number was not correctly saved
2013-11-18 18:48:06 +01:00
Alessandro Ranellucci
754e6ac74b
Update version number. Releasing 1.0.0RC1!
2013-11-18 18:27:12 +01:00
Alessandro Ranellucci
583fc767d8
Fix regression in Avoid Crossing Perimeters. #1531
2013-11-18 17:20:48 +01:00
Alessandro Ranellucci
abe56f96da
Cleaner logic for perimeters, thin walls and gaps. More correct results and faster processing
2013-11-18 17:06:08 +01:00
Alessandro Ranellucci
d4d8045905
Put standby_temperature into options cemetery. #1523
2013-11-16 12:45:43 +01:00
Alessandro Ranellucci
beb7939e22
Rename standby_temperature to ooze_prevention. #1523
2013-11-15 16:01:15 +01:00
Alessandro Ranellucci
5e78f8a0b0
Make sure all extruders are outside skirt at toolchange when standby_temperature is enabled
2013-11-15 15:52:11 +01:00
Alessandro Ranellucci
f733ef5f6b
Handle non-thread-safe Math::Geometry::Voronoi. #1527
2013-11-15 12:55:53 +01:00
Alessandro Ranellucci
ab3e5b5a2c
No support when --support-material-interface-layers was set to 1. #1515
2013-11-14 18:13:57 +01:00
Alessandro Ranellucci
bb37048c35
Added missing encoding in STL repair
2013-11-13 11:12:06 +01:00
Alessandro Ranellucci
4be1e5702a
Free memory after closing the preview and the setting windows
2013-11-12 21:49:34 +01:00
Alessandro Ranellucci
2c416cc4ac
Reduce width of text/spin controls because they're too large on Windows
2013-11-12 17:14:37 +01:00
Alessandro Ranellucci
85232bb6fd
Fix a minor visualization glitch on Windows
2013-11-12 14:34:03 +01:00
Alessandro Ranellucci
faa54ced52
Share the thumbnail object instead of returning it from thread
2013-11-12 14:30:13 +01:00
Alessandro Ranellucci
d0cbf56354
Workaround "Attempt to free unreferenced scalar..." on Linux 32-bit
2013-11-12 12:10:32 +01:00
Alessandro Ranellucci
76213fb5b7
Save the last used Slic3r version and display a notice to encourage legacy users to revert their support material settings to the defaults
2013-11-11 22:20:25 +01:00
Alessandro Ranellucci
004517ad04
Automatically copy Simple Mode settings into a 'Simple Mode' preset in Expert Mode
2013-11-11 22:02:12 +01:00
Alessandro Ranellucci
33e160c1ed
Automatically save presets after running the wizard
2013-11-11 21:45:58 +01:00
Alessandro Ranellucci
885ab5844e
Ported regular_points() to XS and renamed it to equally_spaced_points()
2013-11-11 20:59:58 +01:00
Alessandro Ranellucci
6bb425e88d
Minor fix about raft and support after previous commit
2013-11-11 20:50:22 +01:00
Alessandro Ranellucci
9f41f0279e
Some work to reduce recursive dependencies between classes
2013-11-11 20:37:06 +01:00
Alessandro Ranellucci
bad8afdcda
Fix regression causing incomplete output filepath expansion. #1514
2013-11-11 00:08:50 +01:00
Alessandro Ranellucci
655a546b04
Add .ngc to G-code file name suffixes
2013-11-10 23:37:59 +01:00
Alessandro Ranellucci
8d9361280e
Bugfix: expert mode was crashing when home path contained non-ASCII
...
characters on Windows. #1478
2013-11-10 17:06:59 +01:00
Alessandro Ranellucci
928c4741c2
Fix regression in t/shells.t due to things ported to XS
2013-11-08 11:35:02 +01:00
Alessandro Ranellucci
c133a33ed2
Ported point_line_distance() and removed same_point()
2013-11-06 23:08:03 +01:00
Alessandro Ranellucci
09be25a156
Removed useless functions
2013-11-06 21:09:28 +01:00
Alessandro Ranellucci
d8e098ab0e
Ported same_line() to XS
2013-11-06 19:38:10 +01:00
Alessandro Ranellucci
b5aaeb9b12
More work on the clipping method for medial axis. Includes Polyline->is_valid()
2013-11-06 19:30:45 +01:00
Alessandro Ranellucci
849d69d178
Fix regression in chained_path() introduced in fb763b0187. Includes regression test. #1184
2013-11-02 18:00:55 +01:00
Alessandro Ranellucci
4755e61d71
Bugfix: [input_filename] and [input_filename_base] were only available in the filename pattern and not in the custom G-code settings. #1507
2013-11-02 15:49:20 +01:00
Alessandro Ranellucci
0b63afb370
Fix complete_objects after XS port. Includes regression test. #1511
2013-11-02 14:44:30 +01:00
Alessandro Ranellucci
f491b7ba71
Fix t/support.t
2013-11-02 11:32:23 +01:00
Alessandro Ranellucci
3f7adfc07d
Fix raft_layers according to the new support material logic
2013-11-02 11:16:44 +01:00
Alessandro Ranellucci
d7656f5fdc
Use minimum extrusion width for support material too
2013-10-28 14:04:50 +01:00
Alessandro Ranellucci
ff25cc97fa
Explicitely clip support material with object slices (test case from #1397 )
2013-10-27 23:20:06 +01:00
Alessandro Ranellucci
29b83517cb
Ported point_along_segment(), Polyline::length(), Polyline::clip_end() to XS
2013-10-27 22:57:25 +01:00
Alessandro Ranellucci
26a18a2a52
Temporarily revert to Voronoi-based medial axis
2013-10-27 22:02:57 +01:00
Alessandro Ranellucci
4f64e557d9
Typo
2013-10-27 21:38:32 +01:00
Alessandro Ranellucci
31f77748e7
Explain in the tooltip how is the threshold angle measured
2013-10-27 21:37:26 +01:00
Alessandro Ranellucci
a99d34a91a
Bad memory access in regular_points()
2013-10-27 20:55:55 +01:00
Alessandro Ranellucci
58d92ac36a
Support interface_layers == 0
2013-10-27 18:54:52 +01:00
Alessandro Ranellucci
bcc061176c
New option to use G10/G11 for firmware-controlled retraction. #1494
2013-10-27 16:59:18 +01:00
Alessandro Ranellucci
0e3c9ebe52
Extend interface into base support when the latter is contained in a hole (for better interface anchoring) and fix contact loops when object is enclosed in a hole
2013-10-27 16:37:04 +01:00
Alessandro Ranellucci
4cba5111a3
Fix generation of contact loops
2013-10-27 15:22:44 +01:00
Alessandro Ranellucci
06e7a1ae68
Optimizations to regular_points(), clip_end(), clip_start()
2013-10-27 13:51:59 +01:00
Alessandro Ranellucci
28e9682d0e
Several changes to support material, including a fix to prevent vertical overlapping and horizontal fusion of support and object
2013-10-27 10:19:26 +01:00
Alessandro Ranellucci
c08d4cc798
Fixed support unit tests and reduced dependency on $object
2013-10-26 17:56:59 +02:00
Alessandro Ranellucci
bdf825d078
Refactoring: split support material code into several methods
2013-10-26 17:20:54 +02:00
Alessandro Ranellucci
1741adaddf
Removed debugging line
2013-10-26 09:53:32 +02:00
Alessandro Ranellucci
b653839e9a
One more fix for Cancel button. #1461
2013-10-16 15:13:39 +02:00
Alessandro Ranellucci
127e38d4a4
Fix Cancel button. #1461
2013-10-14 22:07:41 +02:00
Alessandro Ranellucci
4c2c31b554
Fix speed math for wipe, which was causing too fast retraction. Includes regression test. #1468
2013-10-13 17:05:22 +02:00
Alessandro Ranellucci
bc0b9e1b72
Don't combine retract and travel anymore when using G0. #1289
2013-10-13 16:20:01 +02:00
Alessandro Ranellucci
e6b59aef4e
Fix planepath fill patterns for very small regions. #1463
2013-10-13 16:07:14 +02:00
Alessandro Ranellucci
9918c1e97d
Minor improvements in debug output
2013-10-13 12:12:03 +02:00
Alessandro Ranellucci
f603db5e84
Fix --export-svg
2013-10-13 11:45:22 +02:00
Alessandro Ranellucci
ac5e713323
Fix segfault when calling chained_path() on an ExtrusionPathCollection using no_sort. Includes regression test
2013-09-28 15:30:10 +02:00
Mark Hindess
f523c095b1
Trivial fix for support-related undefined sub errors.
2013-09-24 09:54:23 +01:00
Alessandro Ranellucci
0b526afb4e
Change labels in wizard to avoid confusion
2013-09-21 20:25:34 +02:00
Alessandro Ranellucci
0ef6311ac3
Do not set first layer bed temperature if user set bed temperature to zero in wizard
2013-09-21 20:14:17 +02:00
Alessandro Ranellucci
197cd8e68b
Typo
2013-09-19 16:09:47 +02:00
Alessandro Ranellucci
ed529b62f3
Fix threading issue with GUI. #1443 #1444
2013-09-19 16:00:47 +02:00
Alessandro Ranellucci
afdb490cf1
Fix STL export. #1448
2013-09-19 12:25:00 +02:00
Alessandro Ranellucci
032698fb07
Test that toolchanges happen outside skirt when standby-temperature is enabled
2013-09-19 10:44:29 +02:00
Alessandro Ranellucci
40fd7418cd
Added test for standby_temperature
2013-09-19 01:29:34 +02:00
Alessandro Ranellucci
0dd3ab0662
Don't block while cooling extruder
2013-09-18 20:05:15 +02:00
Alessandro Ranellucci
0062c3b7fc
Almost finished the implementation of --standby-temperature
2013-09-18 20:03:59 +02:00
Alessandro Ranellucci
9caf536aca
Finished a basic implementation of --standby-temperature
2013-09-18 18:49:19 +02:00
Alessandro Ranellucci
991bc8ae3d
Partial work for implementing a standby temperature option
2013-09-18 17:45:02 +02:00
Alessandro Ranellucci
4fe0675380
Removed ZTable code
2013-09-17 23:55:38 +02:00
Alessandro Ranellucci
a7989e382c
Bugfix: enabling raft layers generated support for the whole model. Includes regression test. #1375
2013-09-17 23:51:30 +02:00
Alessandro Ranellucci
e0da81e8bf
Introduce a ->count method for all collections to save time
2013-09-17 23:38:23 +02:00
Alessandro Ranellucci
e8323fc339
Move support material code to its own class
2013-09-17 23:27:57 +02:00
Alessandro Ranellucci
6adce9f66b
Update support material code to use shared memory
2013-09-17 23:14:49 +02:00
Alessandro Ranellucci
bbbdae3952
Better name for "Detect overhangs"
2013-09-17 21:49:13 +02:00
Alessandro Ranellucci
ea0e136b45
Prevent superfluous extra perimeters added when a region has an acute angle
2013-09-17 20:18:54 +02:00
Alessandro Ranellucci
06fc1d1044
Fix minor bug causing some gaps to be infilled twice
2013-09-17 19:39:22 +02:00
Alessandro Ranellucci
f79ba8cec0
Update dump-stl.pl
2013-09-17 19:25:10 +02:00
Alessandro Ranellucci
39449f9245
Revert a recent change made to shells generation, causing too much solid infill. Includes regression test. #1431
2013-09-17 19:24:16 +02:00
Alessandro Ranellucci
2c1274e2d9
Updated/fixed SectionCut
2013-09-17 14:16:29 +02:00
Alessandro Ranellucci
7bd2ce21ca
Fix wrong bridge flow used for overhangs and bridge perimeters. Includes regression test. #1407
2013-09-17 10:37:01 +02:00
Alessandro Ranellucci
d13e7b264a
New experimental medial axis code (suboptimal but looks good)
2013-09-17 10:37:01 +02:00
Alessandro Ranellucci
78167f56ee
Some cleanup for the Voronoi code
2013-09-17 10:37:01 +02:00
Alessandro Ranellucci
a88ce0cb5e
Fix regression in start perimeters at non-overhangs. #1442
2013-09-17 10:37:01 +02:00
Alessandro Ranellucci
9a51964e98
Clean medial axis code and gap fill
2013-09-17 10:37:01 +02:00
Alessandro Ranellucci
c7db2cb10f
Prune tiny shells to avoid random extra internal solid infill. #1431
2013-09-16 12:36:04 +02:00
Alessandro Ranellucci
aef5c05c57
Update brim generation code. Includes regression test. #1440
2013-09-16 10:33:30 +02:00
Alessandro Ranellucci
5a9c163a2e
Meaningful error when user wants to use 3D preview but didn't install the required modules.
2013-09-16 10:18:42 +02:00
Alessandro Ranellucci
7d09f17810
Reflect max_fan_speed in cooling textual description. #1439
2013-09-16 10:09:39 +02:00
Alessandro Ranellucci
1aa5dbafd3
Update AMF export code
2013-09-16 09:58:53 +02:00
Alessandro Ranellucci
e2cb40766b
Fix two more Boost calls after xsdata merge. #1429
2013-09-12 11:16:11 +02:00
Alessandro Ranellucci
5f54d0eb90
Fix concentric infill and add regression test. #1432
2013-09-12 11:14:54 +02:00
Alessandro Ranellucci
747fd25f6d
Fix threads, tests and require the most recent Moo version
2013-09-12 11:09:03 +02:00
Alessandro Ranellucci
bc48e17dff
Use precomputed normals in 3D preview
2013-09-11 20:15:42 +02:00
Alessandro Ranellucci
d4512a12df
Make plater work with new XS code
2013-09-11 20:00:51 +02:00
Alessandro Ranellucci
4c96a52012
Read OBJ and AMF
2013-09-11 14:46:38 +02:00
Alessandro Ranellucci
a821eb7f3c
More work to avoid working with vertices outside XS
2013-09-11 11:55:08 +02:00
Alessandro Ranellucci
11e18f681d
Incomplete work to store TriangleMesh objects in Model objects instead of extracting vertices and facets
2013-09-11 09:49:28 +02:00
Alessandro Ranellucci
78ee6e5d6d
Calls to ->repair where needed
2013-09-10 19:25:53 +02:00
Alessandro Ranellucci
566d38a472
Replace TriangleMesh with the XS port
2013-09-10 00:40:46 +02:00
Alessandro Ranellucci
5e34a9cf21
Make Repair() idempotent and lowercase
2013-09-09 23:18:33 +02:00
Alessandro Ranellucci
1b9d2e2ef8
Use the XS slicing code
2013-09-09 18:21:10 +02:00
Alessandro Ranellucci
873762491b
Fix a bad access after recent change about ->p returning objects by reference
2013-09-09 17:10:54 +02:00
Alessandro Ranellucci
5adb187dd2
More porting work
2013-09-07 21:08:53 +02:00
Alessandro Ranellucci
8607c559c7
Minor tidying
2013-09-07 00:42:56 +02:00
Alessandro Ranellucci
09684c67c2
Optimization: Remove useless calls to union()
2013-09-07 00:28:53 +02:00
Alessandro Ranellucci
10ab3bbb86
Fix Only infill where needed putting insufficient material. #1412
2013-09-07 00:02:58 +02:00
Alessandro Ranellucci
907ba55aab
Some minor fixes needed after the xsdata merge. #1421
2013-09-06 22:52:56 +02:00
Alessandro Ranellucci
f104659020
Optimization
2013-09-06 19:21:38 +02:00
Alessandro Ranellucci
4dd12b57a1
Fixed wipe (includes regression test). #1421
2013-09-06 19:14:06 +02:00
Alessandro Ranellucci
e02ae0d18a
Return Surface objects by reference from SurfaceCollection objects and fix a bug in XS code causing some shell options to be ignored
2013-09-06 18:36:38 +02:00
Alessandro Ranellucci
cb677c45de
Don't grow horizontal shells having acute angles. #1387
2013-09-06 17:43:40 +02:00
Alessandro Ranellucci
9484c377d9
Removed debugging line
2013-09-06 16:46:28 +02:00
Alessandro Ranellucci
a2cc54c9d0
Merge pull request #1424 from 4ZM/master
...
Changes to make slic3r build on Arch
2013-09-06 07:43:46 -07:00
Alessandro Ranellucci
2d3dae621a
Minor typos preventing correct positioning after recent XS merge
2013-09-05 14:23:31 +02:00
Anders Sundman
73878e0218
The 'use' prevented the build.
...
There is probably a reason for this line though.
2013-09-04 22:45:19 +02:00
Alessandro Ranellucci
67aefdccc7
Fixed --avoid-crossing-perimeters and --support-material after the xsdata merge
2013-09-04 00:10:53 +02:00
Alessandro Ranellucci
a49dc603cc
Many changes and fixes to remove leaks and return objects by reference
2013-09-03 19:26:58 +02:00
Alessandro Ranellucci
275422fac7
Don't return first_point() and last_point() by reference
2013-09-02 22:33:03 +02:00
Alessandro Ranellucci
0ffb0f6a58
Fix tests
2013-09-02 22:10:52 +02:00
Alessandro Ranellucci
c0789506e4
Return objects by reference instead of always cloning
2013-09-02 20:22:20 +02:00
Alessandro Ranellucci
1cfdf7e955
Ported Slic3r::Polyline::Collection
2013-08-30 00:06:10 +02:00
Alessandro Ranellucci
fb82de9aaf
Removed more unused code
2013-08-29 11:52:25 +02:00
Alessandro Ranellucci
649ef6ce79
Removed unused code
2013-08-29 11:48:58 +02:00
Alessandro Ranellucci
bd7b0e2aed
Ported ExtrusionPath::Collection->chained_path
2013-08-29 11:47:59 +02:00
Alessandro Ranellucci
ea1d138c95
Ported ExtrusionLoop->make_counter_clockwise()
2013-08-29 01:40:42 +02:00
Alessandro Ranellucci
5d6fd7f4d9
Optimizations for better usage of XS code
2013-08-29 01:36:42 +02:00
Alessandro Ranellucci
9254ff9704
Typo in merge
2013-08-28 20:43:23 +02:00
Alessandro Ranellucci
e19c6a1494
Ported Point->distance_to() and Line->length()
2013-08-28 20:41:41 +02:00
Alessandro Ranellucci
c9f68ed28a
Refactor E code and keep track of per-extruder consumend filament
2013-08-28 20:40:13 +02:00
Alessandro Ranellucci
70d824c9a7
One minor optimization in GCode.pm
2013-08-28 20:40:13 +02:00
Alessandro Ranellucci
5f17fa342b
Move arc fitting code to its own post-processing filter and remove the built-in ExtrusionPath::Arc class
2013-08-28 20:40:13 +02:00
Alessandro Ranellucci
055273fbc8
Huge speed boost by reducing the number of method calls in GCode.pm
2013-08-28 20:38:22 +02:00
Alessandro Ranellucci
73c05a6092
Moved vibration limit to its own G-code filter
2013-08-28 20:37:56 +02:00
Alessandro Ranellucci
fb763b0187
Removed dependency on Math::Clipper
2013-08-27 01:26:44 +02:00
Alessandro Ranellucci
b11b595c97
Ported nearest_point() and nearest_point_index()
2013-08-27 00:52:20 +02:00
Alessandro Ranellucci
f1e9216c70
Save some time in GCode.pm method calls
2013-08-27 00:02:24 +02:00
Alessandro Ranellucci
9fb14f2119
Ported (and used) ExtrusionPath->first_point
2013-08-26 23:42:00 +02:00
Alessandro Ranellucci
fe42427a54
Ported Polygon->is_valid() and ExPolygon->is_valid()
2013-08-26 23:27:51 +02:00
Alessandro Ranellucci
da0b85c0d9
Ported ExPolygon->contour and ExPolygon->holes
2013-08-26 23:09:18 +02:00
Alessandro Ranellucci
85011dfef3
Ported Surface->p
2013-08-26 23:03:00 +02:00
Alessandro Ranellucci
494ed5c5ad
Minor optimization (group offset_ex calls)
2013-08-26 22:54:06 +02:00
Alessandro Ranellucci
706851f836
Ported ExPolygon->area()
2013-08-26 22:50:26 +02:00
Alessandro Ranellucci
792fcba7be
Ported Polygon->area
2013-08-26 22:44:40 +02:00
Alessandro Ranellucci
1f734807b9
Ported Polygon->split_at()
2013-08-26 22:39:35 +02:00
Alessandro Ranellucci
9cf831b9c5
Ported union_pt() to XS
2013-08-26 18:37:19 +02:00
Alessandro Ranellucci
443d4e52cb
Fixed everything in the XS port
2013-08-26 17:58:37 +02:00
Alessandro Ranellucci
49040db9a3
Fixes to pass all tests
2013-08-26 16:25:42 +02:00
Alessandro Ranellucci
d786dd6c1c
Merge branch 'master' into xsdata
2013-08-25 22:34:03 +02:00
Alessandro Ranellucci
4bf08cbdec
Minor fix (still no thumbnail)
2013-08-25 22:33:50 +02:00
Alessandro Ranellucci
94a7d6b941
Validate config before launching the object settings dialog
2013-08-25 22:24:43 +02:00
Alessandro Ranellucci
fc9cec9d81
Merge branch 'master' into xsdata
...
Conflicts:
lib/Slic3r/Layer/Region.pm
lib/Slic3r/Print/Object.pm
2013-08-25 19:59:42 +02:00
Alessandro Ranellucci
026e0c06e4
Ability to customize how materials are mapped to extruders. #1020
2013-08-25 19:52:32 +02:00
Alessandro Ranellucci
cb0ee9729f
A couple fixes for Windows
2013-08-25 18:08:56 +02:00
Alessandro Ranellucci
ae9f13ed54
Minor fix to font size
2013-08-25 18:04:45 +02:00
Alessandro Ranellucci
ae21a45886
Distinct dialogs for 3D preview and object settings
2013-08-25 18:03:26 +02:00
Alessandro Ranellucci
b55d4a4e4b
Merge branch 'master' into plater2
2013-08-25 17:52:21 +02:00
Alessandro Ranellucci
e96d7b1d6a
Show facets, materials and manifoldness in info panel
2013-08-25 17:26:55 +02:00
Alessandro Ranellucci
fde6e371a9
Use multiple colors for multimaterial models in 3D preview
2013-08-25 16:35:21 +02:00
Alessandro Ranellucci
5b734f4a13
Merge branch 'master' into plater2
...
Conflicts:
lib/Slic3r/GUI/Plater.pm
2013-08-25 16:10:53 +02:00
Alessandro Ranellucci
2fb725405f
GUI fixes for Windows
2013-08-25 15:45:22 +02:00
Alessandro Ranellucci
3d6fb1b05c
New feature: ability to override specific settings for individual objects in the plater. #344
2013-08-25 14:37:50 +02:00
Alessandro Ranellucci
87b54ba2a0
Plater rearrange experiment
2013-08-25 12:22:05 +02:00
Alessandro Ranellucci
2dd6325bf8
Expose an Open button in the plater
2013-08-25 03:21:20 +02:00
Alessandro Ranellucci
945250c8c2
Show axes and ground
2013-08-25 02:58:50 +02:00
Alessandro Ranellucci
6f1fd51c2e
Keep objects vertical in 3D preview
2013-08-25 02:07:51 +02:00
Alessandro Ranellucci
097912755b
Fix handling of dirty models with overlapping facets, where some holes became filled because of wrong slice nesting
2013-08-19 16:53:54 +02:00
Alessandro Ranellucci
da1b6117df
Minor fix in debug code
2013-08-19 12:16:19 +02:00
Alessandro Ranellucci
94ca28644e
Ported union() to XS
2013-08-17 12:24:04 +02:00
Alessandro Ranellucci
fa07c512b4
Merge branch 'master' into xsdata
...
Conflicts:
lib/Slic3r/Layer/Region.pm
lib/Slic3r/Print.pm
lib/Slic3r/Print/Object.pm
2013-08-16 09:09:56 +02:00
Alessandro Ranellucci
314f377d7b
Debugging code
2013-08-13 20:17:17 +02:00
Alessandro Ranellucci
ef8ce1b5ba
Improvements to SVG debug tools: honor input order and support all colours
2013-08-13 10:34:49 +02:00
Alessandro Ranellucci
2b36778dc1
Fix a situation where extra perimeters prevented top shell to be fully propagated. #1387
2013-08-13 09:45:33 +02:00
Alessandro Ranellucci
36596bf569
Bugfix: alignment code for rectilinear infill caused lack of infill (regression in 948b43f). #1387
2013-08-12 20:27:25 +02:00
Alessandro Ranellucci
f1922ce7b3
Fix regression causing lack of contact infill
2013-08-12 19:19:22 +02:00
Alessandro Ranellucci
e5fe04ea7a
Make sure teeth are not too tight
2013-08-12 19:10:40 +02:00
Alessandro Ranellucci
9513fa7600
Enforce some horizontal margin between object and interface/support (contact not affected)
2013-08-12 18:55:11 +02:00
Alessandro Ranellucci
ca7d4163d7
Remove jitter and overlaps in interface infill
2013-08-12 18:45:03 +02:00
Alessandro Ranellucci
7062d028d2
Bugfix: top layers were not detected correctly, causing overlap of support material and object in some situations where there were contact regions having the same Z as some top regions
2013-08-12 18:12:53 +02:00
Alessandro Ranellucci
8d413eda44
Refactoring: generate interface and support in different cycles
2013-08-11 19:25:51 +02:00
Alessandro Ranellucci
5f07d39509
Reapply perimeter only to support
2013-08-10 21:30:50 +02:00
Alessandro Ranellucci
5380b6cb33
Incomplete work to improve support material by avoiding thin columns and making sure everything is supported correctly
2013-08-10 19:39:35 +02:00
Alessandro Ranellucci
abb5d1256f
Added some debugging code
2013-08-09 21:27:57 +02:00
Alessandro Ranellucci
4862d832b5
Simplify layer change code now that we have distinct support layers
2013-08-09 19:46:20 +02:00
Alessandro Ranellucci
548b301432
Offset projection of facets before the final union
2013-08-09 16:34:55 +02:00
Alessandro Ranellucci
b956faa153
Adapt avoid_crossing_perimeters code to the recent changes
2013-08-09 16:30:40 +02:00
Alessandro Ranellucci
3751e3813c
Fix regression causing too much collapsing of infill regions
2013-08-09 16:18:21 +02:00
Alessandro Ranellucci
5d80c26b29
Adjust collision detection for brim and include support islands inside the only_retract_when_crossing_perimeters logic
2013-08-09 15:04:14 +02:00
Alessandro Ranellucci
67f5b7ab14
Require --default-acceleration when other acceleration settings are used
2013-08-09 14:33:20 +02:00
Alessandro Ranellucci
99816e07a6
New --first-layer-acceleration option
2013-08-09 14:30:43 +02:00
Alessandro Ranellucci
cde662cb51
Fix collision detection for brim
2013-08-09 14:22:41 +02:00
Alessandro Ranellucci
3427b29a93
Fix wrong slices when many overlapping facets were present in the model
2013-08-08 16:27:41 +02:00
Alessandro Ranellucci
f6569cf359
Minor error causing support material to fail when first_layer_height was expressed in % (caught by regression test). #1371
2013-08-08 14:41:23 +02:00
Alessandro Ranellucci
b38cc2c244
Merge branch 'master' into xsdata
...
Conflicts:
lib/Slic3r.pm
lib/Slic3r/ExPolygon.pm
lib/Slic3r/Fill.pm
lib/Slic3r/Fill/Rectilinear.pm
lib/Slic3r/GCode.pm
lib/Slic3r/GUI/Plater.pm
lib/Slic3r/Geometry/Clipper.pm
lib/Slic3r/Layer/Region.pm
lib/Slic3r/Print.pm
lib/Slic3r/Print/Object.pm
lib/Slic3r/TriangleMesh.pm
t/shells.t
xs/MANIFEST
2013-08-08 02:10:34 +02:00
Alessandro Ranellucci
4438aec12c
Revert "Remove thumbnail simplification because it caused loss of very thin parts. #1327 "
...
This reverts commit 1210b89893
2013-08-05 20:48:09 +02:00
Alessandro Ranellucci
0ce7ebc4b8
Integerize plater thumbnails
2013-08-05 20:21:08 +02:00
Alessandro Ranellucci
d8e2cde962
Avoid problems caused in support material by layer heights being specified in configuration without the leading 0 (like .25). #1366
2013-07-31 23:44:17 +02:00
Alessandro Ranellucci
528595c7f7
Automatically ignore per-role extruders if they're not configured in Printer Settings (only in GUI expert mode) - CLI mode continues to autogenerate extruder settings. #1236
2013-07-31 20:43:19 +02:00
Alessandro Ranellucci
d83b14655a
Better tooltip for raft layers
2013-07-31 20:02:24 +02:00
Alessandro Ranellucci
6ddeb2fa07
Initialize support material interface extruder explicitely. #1364
2013-07-31 19:52:25 +02:00
Alessandro Ranellucci
415a2d165a
Cleaner code for first layer temperatures
2013-07-31 18:55:23 +02:00
Alessandro Ranellucci
60e5e2166a
Include support contact layers in skirt/brim generation
2013-07-31 16:29:44 +02:00
Alessandro Ranellucci
3b47e1a492
New --info option to show file info (size, volume, repair stats). Removed utils/file_info.pl
2013-07-31 15:10:11 +02:00
Alessandro Ranellucci
1b4878f305
Fix hang in new support material caused by numerical approximation leaving small polygons, as usual
2013-07-30 15:44:08 +02:00
Alessandro Ranellucci
4e13d61aed
Fix retraction/Z/lift problems after recent changes
2013-07-30 12:15:40 +02:00
Alessandro Ranellucci
913f401280
Merge new-support2
2013-07-29 20:50:26 +02:00
Alessandro Ranellucci
a2cc230bb5
Add note about a bug caused by the disabled optimization about splitting meshes before avoid_crossing_perimeters. #1315
2013-07-29 19:50:47 +02:00
Alessandro Ranellucci
10a8f479f9
Bugfix: lift was not working correctly with multiple extruders and multiple skirt layers. Also, we now ignore all lift settings except the one of the first extruder. Includes regression tests. #1332 #1338
2013-07-29 19:43:57 +02:00
Alessandro Ranellucci
b5907dc734
Bugfix: z_offset was not applied in spiral_vase. Includes regression test #1343
2013-07-29 17:28:30 +02:00
Alessandro Ranellucci
1210b89893
Remove thumbnail simplification because it caused loss of very thin parts. #1327
2013-07-29 16:43:48 +02:00
Alessandro Ranellucci
dc766f9f73
Bugfix: the tangent edge removal algorithm was refactored the wrong way and wasn't used anymore
2013-07-29 14:56:37 +02:00
Alessandro Ranellucci
8fe38d9b71
Bugfix: fatal error when failed loops were included in slices. #1358
2013-07-29 14:17:36 +02:00
Alessandro Ranellucci
9adac636b8
Avoid G92 E0 with sailfish. #1034
2013-07-29 14:17:30 +02:00
Alessandro Ranellucci
80676f358a
Keep edge lines in rectilinear infill even when the sides are not perfectly straight
2013-07-29 13:36:22 +02:00
Alessandro Ranellucci
2a2d15e422
Fix error after recent change about bridges
2013-07-29 12:15:30 +02:00
Alessandro Ranellucci
1f36406a62
Bugfix: thin bridge anchors were ignored. #304
2013-07-29 11:54:32 +02:00
Alessandro Ranellucci
948b43fe0d
Don't try to align rectilinear infill if solid, otherwise there will be a gap at one side
2013-07-29 11:05:04 +02:00
Alessandro Ranellucci
51de3ce14f
Switch print_z to unscaled coordinates
2013-07-29 00:27:53 +02:00
Alessandro Ranellucci
3bcb2f04ed
Add spiral vase test for hollow models
2013-07-28 15:02:03 +02:00
Alessandro Ranellucci
91cade7e8f
Make sure there are no gaps in spiral vase. Includes regression test. #1251
2013-07-28 13:39:15 +02:00
Alessandro Ranellucci
691c45d57f
Smarter handling of hollow prints. Optimization included
2013-07-28 10:56:41 +02:00
Alessandro Ranellucci
25af3eb35f
Proper fix for preventing shells to propagate too much
2013-07-27 19:41:36 +02:00
Alessandro Ranellucci
6bd4803612
Failing test case about spurious infill in hollow objects, caused by shells being correctly generated even for hollow objects - however sometimes we don't want that
2013-07-26 20:17:33 +02:00
Alessandro Ranellucci
0a8872ca6c
Extend utils/dump-stl.pl to also write STL files
2013-07-26 19:25:15 +02:00
Alessandro Ranellucci
debe540018
Better name for wipe
2013-07-26 16:23:43 +02:00
Alessandro Ranellucci
aa194c8125
Fix little regression causing object height not to be updated when object in plater was scaled
2013-07-26 14:30:00 +02:00
Alessandro Ranellucci
c1c1416838
Scale layer height ranges too when scaling object in plater. #1284
2013-07-26 14:26:59 +02:00
Alessandro Ranellucci
a145f1b6aa
Don't merge adjacent bridges so that more correct angles can be detected for each one
2013-07-26 12:31:44 +02:00
Alessandro Ranellucci
c69edf27e9
Bugfix: only_retract_when_crossing_perimeters was not triggering retraction when moving between islands that are covered/bridged on the above layer. #1308
2013-07-26 10:52:22 +02:00
Alessandro Ranellucci
37bf0fa53b
Bugfix: medial axis thin wall detection was triggered when not needed
2013-07-26 00:13:24 +02:00
Alessandro Ranellucci
8fe228fcee
Smarter ordering of gap fill
2013-07-26 00:03:28 +02:00
Alessandro Ranellucci
2b8662cf0c
Temporary workarond for an upstream bug in Moo which causes failure when running with threads. #1330
2013-07-24 10:06:02 +02:00
Alessandro Ranellucci
7ad291ea64
Add ZTable to thread_cleanup()
2013-07-23 23:20:18 +02:00
Alessandro Ranellucci
aa2ad3bbd2
Fix garbage collection of shared data. #1348
2013-07-23 23:18:22 +02:00
Alessandro Ranellucci
b1147861dd
Implement lower_bound() and upper_bound() methods for ZTable
2013-07-20 21:19:59 +02:00
Alessandro Ranellucci
e29aca3553
Reapply correct optimization for simplifiying fill_surfaces before performing the offset. #1325
2013-07-20 12:22:41 +02:00
Alessandro Ranellucci
1b285f3f46
Thread-safe integration of ExtrusionPath::Collection
2013-07-18 22:29:12 +02:00
Alessandro Ranellucci
c030e38908
Ported ExtrusionPath::Collection
2013-07-18 19:09:07 +02:00
Alessandro Ranellucci
0efea9e442
Ported diff() and intersection()
2013-07-17 01:21:30 +02:00
Alessandro Ranellucci
c7b6818ccf
Ported offset() and offset2()
2013-07-17 00:48:29 +02:00
Alessandro Ranellucci
bf8c799685
Ported diff_ex, intersection_ex, union_ex, xor_ex
2013-07-17 00:29:09 +02:00
Alessandro Ranellucci
f7ada2b5db
Ported make_clockwise() and make_counter_clockwise()
2013-07-16 21:09:29 +02:00
Alessandro Ranellucci
fe061b19ad
Ported Polygon->is_counter_clockwise() and rearranged code in .cpp files
2013-07-16 21:04:14 +02:00
Alessandro Ranellucci
79db996696
Ported diff_ex() to XS
2013-07-16 20:29:15 +02:00
Alessandro Ranellucci
898007fc36
Port offset_ex() and offset2_ex() to XS
2013-07-16 20:09:53 +02:00
Alessandro Ranellucci
9458c7db97
Fix integration of XS containers
2013-07-16 17:13:01 +02:00
Mark Hindess
b5426ad297
Revert "Optimization: simplify fill_surfaces before the offset operation"
...
To workaround issue #1325 and possibly #1320 .
This reverts commit 3a046e3411
2013-07-16 10:44:52 +01:00
Alessandro Ranellucci
9b582a11ff
Adopt XS containers everywhere (incomplete work)
2013-07-16 09:49:34 +02:00
Alessandro Ranellucci
ab6b3d41a7
XS interface completed, including new Line class
2013-07-15 22:57:22 +02:00
Alessandro Ranellucci
9af2a1c007
Use XS Point everywhere
2013-07-15 20:31:43 +02:00
Alessandro Ranellucci
d0701cdcd4
Implemented Slic3r::ExtrusionLoop
2013-07-15 16:21:09 +02:00
Alessandro Ranellucci
c9749ca3b3
More integration of Slic3r::Point::XS
2013-07-15 16:04:49 +02:00
Alessandro Ranellucci
159a009f96
Fix tests here and there
2013-07-15 15:26:56 +02:00
Alessandro Ranellucci
f612d4c64e
Ported ExtrusionPath to XS. Failing test for Surface
2013-07-15 12:14:22 +02:00
Alessandro Ranellucci
13e3a9129c
Use Slic3r::ExPolygon::Collection for Layer->slices
2013-07-14 15:06:49 +02:00
Alessandro Ranellucci
7534c1e6d9
Use Slic3r::Surface::Collection for Layer::Region->slices
2013-07-14 15:03:45 +02:00
Alessandro Ranellucci
5885be881c
New Slic3r::Surface::Collection class
2013-07-14 14:56:43 +02:00
Alessandro Ranellucci
399bc80899
Ported Slic3r::Surface to XS
2013-07-14 13:05:55 +02:00
Alessandro Ranellucci
b1ad466189
Ported Slic3r::ExPolygon::Collection to XS
2013-07-14 00:38:01 +02:00
Alessandro Ranellucci
7f4dc4e248
Fix merging error
2013-07-14 00:20:03 +02:00
Alessandro Ranellucci
31809d473f
Merge branch 'master' into xsdata
...
Conflicts:
lib/Slic3r/GCode.pm
xs/src/Point.hpp
2013-07-13 21:00:19 +02:00
Alessandro Ranellucci
027f8d1e53
Optimizations in the algorithm that builds loops
2013-07-13 20:56:13 +02:00
Alessandro Ranellucci
69a8bac9c9
Show a warning if we repaired the input file
2013-07-13 20:34:57 +02:00
Alessandro Ranellucci
6affa23297
Show repair stats in object info dialog
2013-07-13 20:23:03 +02:00
Alessandro Ranellucci
89fae9ee15
Make threaded perls work with XS data in plater thumbnails. Includes cleaner ->arrayref implementation
2013-07-11 19:34:37 +02:00
Alessandro Ranellucci
fb7cea3cb9
Make plater work with XS data in single-thread environment
2013-07-11 19:13:43 +02:00
Alessandro Ranellucci
87a5de193d
ExPolygon::XS->rotate()
2013-07-11 18:55:51 +02:00
Alessandro Ranellucci
1506907212
More incomplete work to make the plater work with XS data
2013-07-11 16:48:44 +02:00
Alessandro Ranellucci
8d171a297e
Add thread cleanup to avoid double destruction of shared XS data
2013-07-11 16:17:36 +02:00
Alessandro Ranellucci
6f6ee40dae
Small optimization in case no overhang logic is required at all
2013-07-07 19:12:44 +02:00
Alessandro Ranellucci
c57a88c943
start_perimeters_at_non_overhang was still partially enforced
2013-07-07 19:11:23 +02:00
Alessandro Ranellucci
5409c27852
Partial GUI compatibility with XS data
2013-07-07 18:43:04 +02:00
Alessandro Ranellucci
8380ca812b
One more arrayref conversion
2013-07-07 17:10:22 +02:00
Alessandro Ranellucci
a1e4bda670
Have Clipper.pm only return ExPolygon::XS objects
2013-07-07 15:17:09 +02:00
Alessandro Ranellucci
53e4532f9c
Merge branch 'master' into xsdata
2013-07-07 12:58:06 +02:00
Alessandro Ranellucci
3a046e3411
Optimization: simplify fill_surfaces before the offset operation
2013-07-07 12:57:26 +02:00
Alessandro Ranellucci
f7967414e0
Store layer slices and region slices as XS data to save memory and make them shared across threads
2013-07-07 12:54:20 +02:00
Alessandro Ranellucci
cca25c9950
Fix a numerical issue causing failure to detect some bridge anchors
2013-07-06 14:38:53 +02:00
Alessandro Ranellucci
532ff3cde9
Apply the Polyline constructor refactoring to the newslice code
2013-07-06 12:18:58 +02:00
Alessandro Ranellucci
985af5ee56
Merge branch 'newslice'
2013-07-06 12:16:54 +02:00
Alessandro Ranellucci
0bb4a5649a
Merge branch 'master' into xs
2013-07-06 12:15:17 +02:00
Alessandro Ranellucci
8d1069766b
Workaround dclone() not being thread-safe
2013-07-06 12:14:49 +02:00
Alessandro Ranellucci
9dbf21235c
Fixed missing change in recent refactoring, causing plater crash. #1298
2013-07-06 11:50:41 +02:00
Alessandro Ranellucci
ab584babf6
Encode Windows paths for the C STL reader
2013-07-06 11:39:28 +02:00
Alessandro Ranellucci
28f8083ab7
Merge branch 'master' into xs
2013-07-06 11:38:40 +02:00
Alessandro Ranellucci
f455ecb7da
Rename adjust_overhang_flow to overhangs
2013-07-06 11:35:40 +02:00
Alessandro Ranellucci
606d856af8
Lower case option group titles
2013-07-06 02:46:09 +02:00
Alessandro Ranellucci
b857d79604
Move spiral_vase to vertical shells section
2013-07-05 22:23:45 +02:00
Alessandro Ranellucci
f8ae8d3e8d
New option to disable overhang flow
2013-07-05 22:12:58 +02:00
Alessandro Ranellucci
282c751b0f
New option for disabling thin wall detection
2013-07-05 22:10:43 +02:00
Alessandro Ranellucci
0a7e0ffecf
New options: start_perimeters_at_concave_points start_perimeters_at_non_overhang
2013-07-05 22:06:58 +02:00
Alessandro Ranellucci
362232ada4
New Quality section in GUI
2013-07-05 21:57:56 +02:00
Alessandro Ranellucci
f0440bede4
Move infill_every_layers infill_only_where_needed into their own "Reducing Printing Time" section
2013-07-05 21:55:01 +02:00
Alessandro Ranellucci
eb2d20d062
Merge branch 'master' into xs
2013-07-05 17:29:28 +02:00
Alessandro Ranellucci
339c487077
Fix starting point after overhang clipping is performed
2013-07-05 17:25:56 +02:00
Alessandro Ranellucci
b3b2a1e891
One more fix in overhang starting point detection
2013-07-05 17:08:26 +02:00
Alessandro Ranellucci
df4612a209
Prefer starting points that are NOT in overhangs
2013-07-05 17:00:14 +02:00
Alessandro Ranellucci
d074b98aba
Optimization: don't store wipe path if wipe is not requested
2013-07-05 15:03:08 +02:00
Alessandro Ranellucci
be4eb3762f
Use dclone() in Point class too
2013-07-05 14:48:03 +02:00
Alessandro Ranellucci
72f77a3420
Use dclone() in Polyline and ExPolygon too
2013-07-05 14:46:32 +02:00
Alessandro Ranellucci
8061cc6e30
Optimization in Polyline instantiation
2013-07-05 14:44:41 +02:00
Alessandro Ranellucci
27c421c27f
Slight optimization
2013-07-05 14:21:20 +02:00
Alessandro Ranellucci
b266d6217a
Skip slow gap detection if we aren't going to fill gaps anyway
2013-07-05 14:17:54 +02:00
Alessandro Ranellucci
4d46ebc6cb
Removed useless, slow, code
2013-07-05 14:17:09 +02:00
Alessandro Ranellucci
f26f084064
New freeze.t test
2013-07-03 15:42:01 +02:00
Alessandro Ranellucci
bb656ea72c
Merge branch 'master' into xs
2013-07-03 10:52:13 +02:00
Alessandro Ranellucci
71057b54a9
Allow negative values in validation...
2013-07-03 10:51:44 +02:00
Alessandro Ranellucci
63ba894260
Add some comments to OpenGL code
2013-07-01 12:23:44 +02:00
Alessandro Ranellucci
8ec3ec6bda
Cosmetic changes to the new OpenGL code by iXce
2013-07-01 10:58:30 +02:00
Alessandro Ranellucci
dcc2b7f4ff
Enable PreviewCanvas
2013-07-01 01:51:11 +02:00
Alessandro Ranellucci
7c4b1bc736
Merge pull request #1283 from iXce/master
...
Panning/rotation/zooming support for 3D viewer
2013-06-30 16:50:16 -07:00
Guillaume Seguin
b2e0c1ab42
Use max of all dimensions instead of max of first 2
2013-07-01 00:08:02 +02:00
Guillaume Seguin
1f229f3233
Cleanup
2013-06-30 23:54:13 +02:00
Guillaume Seguin
e92fefb6ff
Working rotation for mesh viewer
2013-06-30 23:51:06 +02:00
Alessandro Ranellucci
1b6a9c0c3b
Added validation on all settings. #611
2013-06-30 15:39:03 +02:00
Guillaume Seguin
6668a81c64
Start work on rotation handling
2013-06-29 18:31:06 +02:00
Guillaume Seguin
dd7830b1b7
Add panning support
2013-06-29 15:12:57 +02:00
Guillaume Seguin
43d764feff
Implement zoom to point
2013-06-29 14:16:56 +02:00
Guillaume Seguin
317c911c67
Remove leftover from 47b2c13c
2013-06-29 14:16:38 +02:00
Guillaume Seguin
bb3ebb0244
Switch to orthographic projection
2013-06-29 10:43:35 +02:00
Guillaume Seguin
47b2c13c99
Get rid of demo timer in PreviewCanvas
2013-06-29 10:43:21 +02:00
Alessandro Ranellucci
1f50d9c7e8
https -> http in manual URL
2013-06-24 20:38:20 +02:00
Alessandro Ranellucci
5975145426
Automatically repair any input STL file
2013-06-24 20:34:57 +02:00
Alessandro Ranellucci
ecdc2f077b
Merge branch 'master' into xs
...
Conflicts:
Build.PL
2013-06-24 19:37:07 +02:00
Alessandro Ranellucci
f29faf0548
New Slic3r::TriangleMesh::XS class
2013-06-24 19:35:49 +02:00
Alessandro Ranellucci
f5cc446853
Menu item for launching the manual
2013-06-24 18:07:33 +02:00
Alessandro Ranellucci
a15884dac9
Remove useless algorithm in loop merging code
2013-06-24 00:08:39 +02:00
Alessandro Ranellucci
3622193c3f
Rewrite the algorithm that closes loops in order. We now tolerate the case when more than two facets share a common edge
2013-06-24 00:02:01 +02:00
Alessandro Ranellucci
86c4f5c5b0
Merge branch 'master' into newslice
2013-06-23 22:23:25 +02:00
Alessandro Ranellucci
de45b823e1
Merge branch 'master' into xs
2013-06-23 21:12:19 +02:00
Alessandro Ranellucci
2a2633da0a
New automatic built-in STL repair
2013-06-23 21:11:46 +02:00
Alessandro Ranellucci
625a300822
New [layer_num] placeholder in layer change G-code
2013-06-23 19:25:32 +02:00
Alessandro Ranellucci
8ea4ed3b5e
Allow to supply custom G-code via command line if file is not found
2013-06-23 19:25:02 +02:00
Alessandro Ranellucci
2d687cd0a0
Only combine internal infill and leave internal-solid as it is. #1248
2013-06-23 18:21:47 +02:00
Alessandro Ranellucci
f3a9d41c70
Cache a Z table for layer range search
2013-06-23 17:07:12 +02:00
Alessandro Ranellucci
37105e8237
Ported get_layer_range() to C
2013-06-23 15:33:07 +02:00
Alessandro Ranellucci
9a904dc88d
Lighter implementation of the slicing algorithm to save memory and time
2013-06-23 12:26:40 +02:00
Alessandro Ranellucci
cd1a39397b
Optimize concentric loops
2013-06-23 00:50:44 +02:00
Alessandro Ranellucci
78f1527ab7
Compensate perimeter/infill overlap for concentric infill
2013-06-23 00:37:04 +02:00
Alessandro Ranellucci
5c7b447f07
Ensure there's no numerical error when searching for concave points
2013-06-23 00:21:19 +02:00
Alessandro Ranellucci
1e3ce9b8c4
Complete retraction if the wipe path was too short for the full retract. #1264
2013-06-23 00:10:57 +02:00
Alessandro Ranellucci
c03f9f0197
Fixed regression causing wrong direction for inwards move in holes. Includes regression test. #1265
2013-06-23 00:05:08 +02:00
Alessandro Ranellucci
0bd3d958e2
More optimizations in slice_facet()
2013-06-22 20:48:56 +02:00
Alessandro Ranellucci
1565560b55
One more little optimization
2013-06-22 20:37:15 +02:00
Alessandro Ranellucci
db266cde9f
Little optimizations in slicing
2013-06-22 20:32:39 +02:00
Alessandro Ranellucci
398e66572d
Optimization: remove overkill sort
2013-06-22 19:59:27 +02:00
Alessandro Ranellucci
82fbdb603f
Optimization: cache model bounding box
2013-06-22 19:36:50 +02:00
Alessandro Ranellucci
4774b0e910
Be tolerant with STL files without the "normal" word
2013-06-22 16:15:07 +02:00
Alessandro Ranellucci
64a21276e3
Add regression test for concave starting points. #135
2013-06-22 15:22:58 +02:00
Alessandro Ranellucci
b35e668ee7
Require Boost::Geometry::Utils 0.15
2013-06-21 19:46:45 +02:00
Alessandro Ranellucci
aba7641fe4
Avoid starting loops on convex vertices and/or overhangs. #296 #135
2013-06-21 19:43:15 +02:00
Alessandro Ranellucci
90d8da0e0d
Limit fan speed to 100% :-)
2013-06-21 16:08:16 +02:00
Alessandro Ranellucci
19b40baf55
Add regression test to ensure fan is enabled when printing overhangs. #432
2013-06-21 15:38:58 +02:00
Alessandro Ranellucci
c707073a73
Some fixes about overhang detection. Includes regression tests
2013-06-21 14:52:35 +02:00
Alessandro Ranellucci
f5322596d9
Note to self in code
2013-06-20 20:16:15 +02:00
Alessandro Ranellucci
7e875393f5
New algorithm for overhang detection
2013-06-20 20:11:46 +02:00
Alessandro Ranellucci
015580629b
Removed wrong optimization causing possible extra retractions while moving in infill space
2013-06-20 19:43:53 +02:00
Alessandro Ranellucci
4474595629
Removed useless code
2013-06-20 19:21:35 +02:00
Alessandro Ranellucci
b414c50b68
Optimization: use Boost.Geometry for point in polygon
2013-06-20 18:48:11 +02:00
Alessandro Ranellucci
f7be746599
Disable overhang detection for now
2013-06-19 20:09:58 +02:00
Alessandro Ranellucci
fcd4de00e5
One more fix for --complete-objects working on single-object plates
2013-06-19 18:01:24 +02:00
Alessandro Ranellucci
5843f5df6c
Fix regression in --complete-objects causing fatal error and/or wrong warnings about object heights
2013-06-19 17:34:37 +02:00
Alessandro Ranellucci
b71bc37111
Remove a couple cases of dangerous aliasing, causing crashes. #1257
2013-06-17 19:27:08 +02:00
Alessandro Ranellucci
799aeedd97
Fixed wrong refactoring in ac4a0bcdd8
2013-06-17 13:32:53 +02:00
Alessandro Ranellucci
c4036470af
Fix one thing leftover from bounding box refactoring
2013-06-17 12:11:28 +02:00
Alessandro Ranellucci
c6ef81fb91
Modify overhang detection algorithm
2013-06-16 18:08:17 +02:00
Alessandro Ranellucci
45611d6742
Fix connection algorithm for rectilinear infill as sometimes it wasn't connecting segments correctly
2013-06-16 18:05:56 +02:00
Alessandro Ranellucci
0ad78eaf55
Return explicit 0 from have_version_check() to avoid wxMenuItem->Enable errors
2013-06-16 16:07:47 +02:00
Alessandro Ranellucci
3bcf1da702
Disable avoid_crossing_perimeters optimization until we can detect nested shells. #1254
2013-06-16 16:04:19 +02:00
Alessandro Ranellucci
32aafd2eb9
Temporary workaround until Boost::Geometry::Utils 0.14 is available
2013-06-16 15:11:39 +02:00
Alessandro Ranellucci
258842b845
New logic for connecting honeycomb loops
2013-06-16 13:31:10 +02:00
Alessandro Ranellucci
9ff85898b1
New logic for connecting honeycomb paths
2013-06-16 13:26:57 +02:00
Alessandro Ranellucci
961586fe8f
Rewrite honeycomb infill so that it only generates the pattern for the bounding box of the region instead of the full print, so reduce complexity of the clipping routine
2013-06-16 13:13:52 +02:00
Alessandro Ranellucci
ac4a0bcdd8
Refactoring: use Slic3r::Geometry::BoundingBox objects everywhere
2013-06-16 12:21:25 +02:00
Alessandro Ranellucci
07407e5dbd
Merge branch 'master' into overhang
...
Conflicts:
lib/Slic3r/GCode.pm
2013-06-16 10:49:33 +02:00
Alessandro Ranellucci
2993a1659e
Bump version number
2013-06-16 10:22:22 +02:00
Alessandro Ranellucci
d0eac88ff9
Reduce vibrations when doing gap fill
2013-06-15 21:27:36 +02:00
Alessandro Ranellucci
8b48d79563
Improve zigzag gap fill. #1234
2013-06-15 21:10:04 +02:00
Alessandro Ranellucci
cb75b1e47b
Fix plater crash on threaded perls
2013-06-15 19:15:24 +02:00
Alessandro Ranellucci
8d9d023dd7
Merge branch 'honeycomb-clipping'
2013-06-15 18:10:16 +02:00
Alessandro Ranellucci
20158aac0d
Merge branch 'issue1161'
2013-06-15 18:08:01 +02:00
Alessandro Ranellucci
7560d5f131
Merge branch 'perl-518'
2013-06-15 18:06:36 +02:00
Alessandro Ranellucci
8b6afb61d9
Fix little error in tests
2013-06-15 17:17:48 +02:00
Alessandro Ranellucci
7bf308c08f
Fix one more centering problem caused by wrong bounding box implementation
2013-06-15 15:50:02 +02:00
Alessandro Ranellucci
a8981b8b35
Bugfix: infill was clipped badly. Includes regression test. #1245
2013-06-15 12:10:57 +02:00
Alessandro Ranellucci
5fa49aad02
Releasing 0.9.10
2013-06-14 16:59:20 +02:00
Alessandro Ranellucci
878d17605c
Ignore solid_infill_every_layers when fill_density is 0. Includes regression test. #1240
2013-06-14 16:48:24 +02:00
Alessandro Ranellucci
145fe08203
More fixes for plater positioning. #1171
2013-06-13 20:05:32 +02:00
Alessandro Ranellucci
962a51cc80
Some cleanup for the plater code
2013-06-13 14:33:10 +02:00
Alessandro Ranellucci
def013ba91
Use _transform_thumbnail when rescaling thumbnails
2013-06-13 11:28:27 +02:00
Alessandro Ranellucci
0a74e45432
Scale and recenter thumbnails when bed size and/or print center is changed
2013-06-13 11:27:15 +02:00
Alessandro Ranellucci
5dcf277563
Rotate cw when using free rotation button to be consistent with icon. #1171
2013-06-13 10:27:47 +02:00
Alessandro Ranellucci
aee7b70d79
Bugfix: the order of transformations was not consistent in plater and actual G-code generation. #1171 #1191
2013-06-12 16:53:19 +02:00
Alessandro Ranellucci
8e0e03247d
Bugfix: ineffective scale() method in recently created BoundingBox objects caused wrong positioning for scaled objects in plater. Includes regression test. #1171
2013-06-10 15:34:45 +02:00
Alessandro Ranellucci
8b2c13cc6f
Regression test for top solid surfaces in V-shaped object. #1161
2013-06-08 20:01:26 +02:00
Alessandro Ranellucci
d5a9320587
Bugfix: narrow top surfaces didn't generate solid layers. #1161
2013-06-08 17:48:34 +02:00
Alessandro Ranellucci
b12a09ed71
Rename makerbot G-code flavor to makerware; also mention Repetier among RepRap firmwares. #1034
2013-06-07 23:24:53 +02:00
Alessandro Ranellucci
510c2092df
Fix rotation and scaling in plater producing mispositioned objects in G-code after recent changes. Includes a large refactoring and the new Slic3r::Geometry::BoundingBox class. #1171 #1191
2013-06-07 23:16:02 +02:00
Alessandro Ranellucci
9ea55497c2
Prevent crash when user deleted object from plater before thumbnail was generated in the other thread. #1207
2013-06-07 13:54:40 +02:00
Alessandro Ranellucci
f991e3bc10
Fixed SVG export and added regression test
2013-06-07 12:00:03 +02:00
Alessandro Ranellucci
fcc442882c
Fix plater defect causing misalignment
2013-06-06 20:53:56 +02:00
Alessandro Ranellucci
43814e99f6
Remove smart match and lexical $_ for compatibility with perl 5.18. #1216
2013-06-06 10:46:58 +02:00
Alessandro Ranellucci
8c40cefe1e
Also use G1 when traveling with avoid_crossing_perimeters enabled
2013-06-05 17:12:34 +02:00
Alessandro Ranellucci
532ae53d0b
Use G1 instead of G0 for restart after retraction to avoid blending with the previous travel move. #1212
2013-06-05 16:58:30 +02:00
Alessandro Ranellucci
b3f1795cb4
Reduce wipe feedrate a bit
2013-06-03 22:49:47 +02:00
Alessandro Ranellucci
8b3aa32a7e
Update tooltip for only_retract_when_crossing_perimeters
2013-06-03 22:40:29 +02:00
Alessandro Ranellucci
230367b383
Order objects using a nearest neighbor search instead of relying on the order in plater. #1184
2013-06-03 21:54:55 +02:00
Alessandro Ranellucci
3ffe98f0c3
Use actual Z to order objects in sequential printing rather than layer count, as layer heights might be different
2013-06-03 21:40:13 +02:00
Alessandro Ranellucci
09b81ad027
Fix typo causing regression in island ordering. #1211
2013-06-03 21:27:09 +02:00
Alessandro Ranellucci
c95245f143
Some G-code flavor logic simplification
2013-06-03 18:01:14 +02:00
Alessandro Ranellucci
167ec7a4e7
Use M135 for makerbot toolchange; also disable any G90 and G21 command. #1034
2013-06-03 16:21:22 +02:00
Alessandro Ranellucci
974379c955
Add M103 after retraction and M101 before restart when Makerbot G-code flavor is selected. #1119
2013-06-03 15:37:32 +02:00
Alessandro Ranellucci
71608e799e
Keep per-extruder E absolute value for Makerbot flavour to avoid any G92 E0. #950
2013-06-03 15:27:58 +02:00
Alessandro Ranellucci
48d5d6de58
Typo
2013-06-03 12:29:45 +02:00
Alessandro Ranellucci
81bae56e92
Limit only_retract_when_crossing_perimeters to travel moves that are completely enclosed in the upper layer's slices so that we avoid visible traces on top layers. #1091
2013-06-03 12:25:32 +02:00
Alessandro Ranellucci
7134df4638
Only skip objects with no layers without stopping the whole job
2013-06-03 11:39:23 +02:00
Alessandro Ranellucci
8c74d2f41e
New --autosave option for better toolchain integration. #837
2013-06-02 20:03:22 +02:00
Alessandro Ranellucci
895e0bbfcd
Include M82/M83 for Teacup too. #1206
2013-06-02 19:58:29 +02:00
Alessandro Ranellucci
6bb2e593a7
Avoid potential fatal error when processing models with empty layers. #1127
2013-06-02 19:49:21 +02:00
Alessandro Ranellucci
8a01cb9e96
Generate a better error when input file is too thin and no layers could be generated. #1127
2013-06-02 19:44:59 +02:00
Alessandro Ranellucci
086ec4af9c
Fixed yet one more regression in Quick Slice caused by recent Model refactoring. #1208
2013-06-02 19:32:53 +02:00
Alessandro Ranellucci
28a01e7c5e
Fix past participle
2013-06-02 16:58:23 +02:00
Alessandro Ranellucci
655d528d92
Fixed recent regression causing a spike when avoid_crossing_perimeters was used on split objects
2013-06-02 16:56:08 +02:00
Alessandro Ranellucci
da36df65a4
Warning removed when exporting config
2013-06-02 11:15:57 +02:00
Alessandro Ranellucci
30ce7dc745
Bugfix: wizard crashing in Simple Mode. #1077 #1122
2013-06-01 18:56:23 +02:00
Alessandro Ranellucci
d801876ee9
Revert "Bugfix: configuration wizard crash 2 #1077 "
...
This reverts commit 55c413627f
2013-06-01 18:54:07 +02:00
Alessandro Ranellucci
973d30a2b4
Merge pull request #1148 from hroncok/patch-1
...
Bugfix: configuration wizard crash 2 #1077
2013-06-01 09:46:17 -07:00
Alessandro Ranellucci
49531f6f78
Fixed regression causing rotation from plater to also translate the resulting G-code. #1191
2013-05-31 19:41:31 +02:00
Alessandro Ranellucci
c62b49d1af
Optimization of extra perimeters detection
2013-05-31 14:30:07 +02:00
Alessandro Ranellucci
917915d68e
Bugfix: superfluous extra perimeters were generated. #1170
2013-05-31 14:23:42 +02:00
Alessandro Ranellucci
5f06cea821
Prevent --extrusion-multiplier <= 0. #1183
2013-05-31 12:45:18 +02:00
Alessandro Ranellucci
5c7dd2cf78
Some fixes to the cooling logic and new test suite for cooling
2013-05-31 12:18:33 +02:00
Alessandro Ranellucci
da76496988
Store config in Slic3r::GCode object
2013-05-31 11:19:36 +02:00
Alessandro Ranellucci
7baaf6bf5d
Fixed regression causing skirt_height to he honored incorrectly when printing more than one object. Includes regression test #1200
2013-05-30 20:06:05 +02:00
Alessandro Ranellucci
8f5a958948
Rename do_slice() to quick_slice()
2013-05-20 11:02:12 +02:00
Alessandro Ranellucci
71d6f428ca
Apparent fix for "Attempt to free unreferenced scalar"
2013-05-20 10:57:27 +02:00
Alessandro Ranellucci
c43ef45064
Require the newest Math::Clipper and Boost::Geometry::Utils to avoid the huge memory leaks present in previous versions
2013-05-20 09:56:55 +02:00
Alessandro Ranellucci
f13d4e4e66
Restore skirt preview and extrude clearance after recent usage of int_offset()
2013-05-19 18:03:18 +02:00
Alessandro Ranellucci
5494f4f385
Free @_ before spawning a new thread (known old Perl bug) as an attempt to fix the unref scalars error
2013-05-19 17:34:33 +02:00
Alessandro Ranellucci
48e37f97b4
Fixed bad copy and paste causing multiple extruders to throw an error
2013-05-19 15:33:54 +02:00
Alessandro Ranellucci
bbb190dc68
Generate infill using each object's bounding_box instead of full print. #1177
2013-05-19 11:35:41 +02:00
Alessandro Ranellucci
627debf284
Scale bounding_box by sqrt(2) in honeycomb too to ensure it will cover the object even after rotation, like we already did for Rectilinear
2013-05-19 11:25:41 +02:00
Alessandro Ranellucci
b5b0c2cc89
Bad copy and paste in commit from yesterday causing loss of perimeters. #1178
2013-05-19 10:47:00 +02:00
Alessandro Ranellucci
7180e7cb30
Speed optimization in avoid_crossing_perimeters
2013-05-19 10:35:11 +02:00
Alessandro Ranellucci
f599ed00c6
Avoid closures, move planning code to _plan() and layer G-code generation to Slic3r::GCode::Layer
2013-05-18 17:41:37 +02:00
Alessandro Ranellucci
08a0bbd7f0
Optimization: split meshes automatically when avoid_crossing_perimeters is enabled, so that we reduce the complexity of the MotionPlanner graphs. This commit includes a very large refactoring of the Model class which is now responsible for duplication and arrangement
2013-05-18 16:48:26 +02:00
Alessandro Ranellucci
e33ca54943
Some code cleanup in MotionPlanner
2013-05-17 20:03:38 +02:00
Alessandro Ranellucci
ba433822b6
Disable OpenGL code in master branch for now
2013-05-17 15:44:23 +02:00
Alessandro Ranellucci
8f77d3b945
Increase spacing for bridge traces. #1090
2013-05-17 15:03:42 +02:00
Alessandro Ranellucci
8e2063397a
Merge branch 'opengl'
2013-05-17 14:17:02 +02:00
Alessandro Ranellucci
5c74fd095b
Very basic implementation of 3D preview - install Wx::GLCanvas to get it working
2013-05-17 14:14:33 +02:00
Alessandro Ranellucci
61c1045331
Merge branch 'master' into overhang
2013-05-16 18:36:11 +02:00
Alessandro Ranellucci
228c84ddc1
Use glDrawArrays()
2013-05-16 13:42:19 +02:00
Alessandro Ranellucci
09989ab8bd
Fix regression in --gcode-arcs
2013-05-16 12:54:38 +02:00
Alessandro Ranellucci
521d668712
Reduce overlap for bridges. #1090
2013-05-16 12:34:24 +02:00
Alessandro Ranellucci
55071e544f
Fix brim spacing. #1174
2013-05-16 12:29:46 +02:00
Alessandro Ranellucci
fc1a23f5b0
Quick and dirty OpenGL mockup
2013-05-16 12:09:01 +02:00
Alessandro Ranellucci
bff31d7002
Fix split_mesh() not working anymore since analyze() is lazy
2013-05-16 11:25:15 +02:00
Alessandro Ranellucci
a94d26b1ce
Fix overhang detection for contours
2013-05-15 10:50:38 +02:00
Alessandro Ranellucci
575127151b
New algorithm for overhang detection
2013-05-14 20:19:42 +02:00
Alessandro Ranellucci
90280fe63b
Little fix for bridge rendering in SectionCut
2013-05-14 20:11:05 +02:00
Alessandro Ranellucci
967d567db0
Fix bridge rendering in SectionCut
2013-05-14 19:48:52 +02:00
Alessandro Ranellucci
632652d924
Unfinished work for displaying bridge paths in section cuts
2013-05-14 19:48:47 +02:00
Alessandro Ranellucci
06ad6b70f8
Bugfix: scaling object from the plater applied scale factor over the factor used in the previous slicing job. #1075
2013-05-14 16:31:50 +02:00
Alessandro Ranellucci
7eff002e21
Memory and speed optimization: only study meshes when needed
2013-05-14 14:47:00 +02:00
Alessandro Ranellucci
e51dbb994d
One more speed optimization in STL.pm
2013-05-14 14:17:46 +02:00
Alessandro Ranellucci
745cea8e6c
One more little speed optimization in STL.pm
2013-05-14 14:12:32 +02:00
Alessandro Ranellucci
25bafe7ff1
Memory (and maybe speed?) optimization in STL reader
2013-05-14 13:54:25 +02:00
Alessandro Ranellucci
4121a7ece5
Set support material enforce layers to 0 when spiral printing
2013-05-14 13:54:24 +02:00
Mark Hindess
7979dd9e9c
Avoid expensive TriangleMesh BUILD method during clone.
...
Gives 6% speedup and uses less memory when slicing yoda.stl and should
give significantly bigger speedup on more complex models and plates.
2013-05-13 21:27:55 +01:00
Alessandro Ranellucci
a86c48d85c
Disable retract on layer change when doing spiral vase; also check that we're printing a single-material object
2013-05-13 21:55:34 +02:00
Alessandro Ranellucci
a73020c10e
Faster implementation of concentric infill, with loop order reversed so that smaller loops will be printed at the end. #898
2013-05-13 21:22:57 +02:00
Alessandro Ranellucci
ccdb29ddc9
New --spiral-vase option to continously raise Z when printing single-walled vases. #997
2013-05-13 20:15:45 +02:00
Alessandro Ranellucci
baa1a8c736
Move Slic3r::Test::GCodeReader to Slic3r::GCode::Reader
2013-05-13 20:14:33 +02:00
Alessandro Ranellucci
ece6dd8a0b
Only make the inwards move when we have more than one perimeter
2013-05-13 19:35:42 +02:00
Alessandro Ranellucci
7c89476602
Move fan_always_on in the Enable options group. #1166
2013-05-13 18:33:44 +02:00
Alessandro Ranellucci
1aae311148
Fix menus for --no-plater. #1112
2013-05-13 18:30:12 +02:00
Alessandro Ranellucci
f6dc712158
Bugfix: most of the File menu items didn't work with --no-plater. #1112
2013-05-13 18:22:47 +02:00
Alessandro Ranellucci
d2425748a3
Code cleanup and remove arc compensation code
2013-05-13 13:18:58 +02:00
Alessandro Ranellucci
5efa409c7c
Move gap fill to its own method
2013-05-13 13:07:22 +02:00
Alessandro Ranellucci
1d94618c5e
Correctly detect external hole perimeters
2013-05-13 12:52:57 +02:00
Alessandro Ranellucci
ca549cd2fe
Perimeters refactoring complete
2013-05-11 21:30:26 +02:00
Alessandro Ranellucci
67b24efd49
Incomplete work - still wrong order
2013-05-11 21:05:29 +02:00
Alessandro Ranellucci
df62c25c8f
One more offset_ex() optimization
2013-05-11 09:39:38 +02:00
Alessandro Ranellucci
0e100827f8
Avoid useless looping and usage of ExPolygons
2013-05-11 09:35:33 +02:00
Alessandro Ranellucci
6e216e2fd9
New traverse_pt()
2013-05-11 09:24:48 +02:00
Alessandro Ranellucci
7953dcfb12
Merge branch 'better-brim'
...
Conflicts:
lib/Slic3r/Geometry/Clipper.pm
lib/Slic3r/Print.pm
2013-05-11 09:19:23 +02:00
Alessandro Ranellucci
bac5093de4
Alwyas apply disable_fan_first_layers, even if cooling is disabled, since fan_always_on is applied in that case as well. Update descriptive text and have it appear in case of disabled auto cooling. #1166
2013-05-10 15:09:27 +02:00
Alessandro Ranellucci
6b8894cf9a
Rename ex_int_offset2 to offset2_ex
2013-05-10 13:56:29 +02:00
Alessandro Ranellucci
993fcd9182
Revert "Smarter ordering of brim loops. #687 " until new Math::Clipper is out
...
This reverts commit 4aad2f6243
2013-05-10 13:51:28 +02:00
Alessandro Ranellucci
5bf3f5f5e4
Make sure brim paths don't overlap
2013-05-10 13:47:40 +02:00
Alessandro Ranellucci
4aad2f6243
Smarter ordering of brim loops. #687
2013-05-09 14:52:56 +02:00
Alessandro Ranellucci
855ba90332
New script to generate vertical section cuts from any given G-code file
2013-05-02 11:42:51 +02:00
Alessandro Ranellucci
dde3e6e870
Disable Net::DBus. #1015
2013-04-29 15:57:07 +02:00
Alessandro Ranellucci
c2301c5796
Don't extend solid layers when fill density is 0
2013-04-29 15:55:50 +02:00
Alessandro Ranellucci
f7153d67d0
Make preset placeholders available in Quick Slice too. #921
2013-04-28 23:26:50 +02:00
Alessandro Ranellucci
bde730a611
Little fix in SectionCut.pm
2013-04-28 11:31:03 +02:00
Alessandro Ranellucci
6db8afe36d
New option to remember last output directory. #698
2013-04-27 21:07:30 +02:00
Alessandro Ranellucci
f5bda326b8
Version check. #1006
2013-04-27 20:55:43 +02:00
Alessandro Ranellucci
bc9ff47d3f
New module to output SVG vertical sections of extrusion paths with real width and height. The commit includes a bugfix to the Polyline->grow() method and some simplification in the Line class which is now child of Polyline
2013-04-27 15:02:13 +02:00
Alessandro Ranellucci
6842114d3d
Fix for rectilinear infill failing in plates with new caching
2013-04-26 17:14:30 +02:00
Alessandro Ranellucci
24fd152ce4
Bugfix: cooling buffer was broken. #1149
2013-04-24 11:19:08 +02:00
Miro Hrončok
55c413627f
Bugfix: configuration wizard crash 2 #1077
2013-04-23 16:17:43 +03:00
Mark Hindess
8c26f0da30
Avoid memory leaks by breaking reference cycle: Print -> Fill -> Print
2013-04-18 22:49:43 +01:00
Mark Hindess
aac2c45450
Avoid merging meshes when there is only one mesh to merge.
...
When slicing yoda.stl it reduces peak memory usage by 5% and speeds up
slicing by 13%.
Further optimization using a simple proxy to implement the two methods
(size/extends) needed on the merge meshes is also possible and
undoubtedly worthwhile.
2013-04-18 19:50:05 +01:00
Mark Hindess
407de02fe4
Use binary search for get_layer_range.
...
Gives a 13% speed up on Teethy_Tiki.stl (thing:49334) with default settings
on my laptop.
When $self->layers->[0]->slice_z == $min_z the returned $min_layer value is
0 rather than the (incorrect?) -1 returned by the old code.
2013-04-18 19:29:05 +01:00
Alessandro Ranellucci
4e6c58f749
TYpo
2013-04-18 19:49:02 +02:00
Alessandro Ranellucci
17f76c4951
Move bridge detection to its own method
2013-04-18 18:43:46 +02:00
Alessandro Ranellucci
e088d9b3f7
Cache Slic3r::Fill object
2013-04-18 18:40:59 +02:00
Alessandro Ranellucci
312bb285a0
Fix initialization of Rectilinear filler
2013-04-18 18:37:46 +02:00
Alessandro Ranellucci
c46bfc71b4
Merge branch 'master' into boost-optimizations
2013-04-18 17:48:46 +02:00
Alessandro Ranellucci
01bd9040f5
Fix syntax for ex_int_offset2()
2013-04-18 17:46:13 +02:00
Alessandro Ranellucci
b160feacfd
Merge branch 'master' into clipper-optimizations
2013-04-18 17:36:42 +02:00
Alessandro Ranellucci
850690cf79
Minor optimization
2013-04-18 17:36:06 +02:00
Alessandro Ranellucci
430c825918
Align rectilinear and line infill across layers (new implementation). #712
2013-04-18 17:34:21 +02:00
Alessandro Ranellucci
bd3384525e
Revert "Align rectilinear and line infill across layers. #712 "
...
This reverts commit a0a54ea706
2013-04-15 11:33:24 +02:00
Alessandro Ranellucci
a0a54ea706
Align rectilinear and line infill across layers. #712
2013-04-11 19:36:49 +02:00
Alessandro Ranellucci
c2aa119c09
Require Boost::Geometry::Utils 0.08
2013-04-09 14:03:24 +02:00
Alessandro Ranellucci
94ed6cd239
Always move Z at travel speed. #1093
2013-04-08 22:23:51 +02:00
Jesse Vincent
7ec6332141
split apart the math in nearest_point_index and short-circuit if we know the candidate is no good
2013-04-07 19:53:15 -04:00
Jesse Vincent
e8ca1e59a6
no functional change. only return from one place for clarity
2013-04-07 19:44:32 -04:00
Jesse Vincent
da0e67a891
Only look up $point's X and Y once, rather than once on every pass through the loop.
...
(Those lookups are expensive)
2013-04-07 18:28:08 -04:00
Jesse Vincent
3e8c5804fe
Inline comparable_distance_between_points
...
It was called on an incredibly hot codepath from a single place. At 12313276 calls
on my test .stl, the sub call overhead alone was a significant perf hit.
2013-04-07 18:13:40 -04:00
Jesse Vincent
060d2da7fe
Small optimization on an incredibly hot codepath.
2013-04-07 18:01:15 -04:00
Alessandro Ranellucci
7e51cbcf69
Allow 0.1mm slots. #959 #1056
2013-04-04 01:24:40 +02:00
Alessandro Ranellucci
b4be61b703
Bugfix: time estimates for cooling were computed for each object separately instead of the whole actual layer. #1071
2013-04-04 01:17:44 +02:00
Alessandro Ranellucci
a563801304
Merge branch 'master' of github.com:alexrj/Slic3r
2013-04-04 01:15:46 +02:00
Alessandro Ranellucci
3afeb5c7b5
Second layer commands were written multiple times
2013-04-04 00:52:11 +02:00
Alessandro Ranellucci
b725847a51
Bugfix: configuration wizard led to crash with simple mode. #1077
2013-04-03 19:26:59 +02:00
Alessandro Ranellucci
88e70a59c7
Don't wipe if option is disabled
2013-04-03 19:08:12 +02:00
Alessandro Ranellucci
d089d2b2d4
Bugfix: crash introduced by wipe
2013-04-03 19:06:33 +02:00
Devin Grady
e602aad998
inspired by f5e48a3, a seems to work to fix 1076
2013-04-01 22:12:51 -05:00
Alessandro Ranellucci
bf809d1fd0
Use linestring_length() from Boost
2013-03-31 19:50:22 +02:00
Alessandro Ranellucci
1187f4846d
Some Clipper optimizations
2013-03-31 19:40:25 +02:00
Alessandro Ranellucci
0d6ff22e19
Merge branch 'wipe'
2013-03-31 11:36:04 +02:00
Alessandro Ranellucci
0e6d80d33c
Bump version number
2013-03-31 11:24:33 +02:00
Alessandro Ranellucci
01e86c2615
Releasing 0.9.9
2013-03-30 15:59:17 +01:00
Alessandro Ranellucci
04d2231901
Bugfix: is_printable() wasn't discarding narrow ring-shaped top/bottom surfaces because it was only considering the contour. This caused extra shell material even in hollow prints. #1049
2013-03-30 11:22:12 +01:00
Alessandro Ranellucci
7f23e72a10
Display preview for small files too. #929
2013-03-30 00:52:45 +01:00
Alessandro Ranellucci
33a4ec660d
better handling of too-small and too-short models #929 .
...
These changes handle small models better in the plater preview.
Extremely small thumbnails are preserved instead of culled,
allowing the model to be scaled up. The scale range is extended to
100000% to allow mm-scale objects expressed in meters to be opened
and scaled to mm.
Original coding by mesheldrake
2013-03-30 00:47:13 +01:00
Alessandro Ranellucci
ac2356f66a
Don't crash at the end of empty prints. #1042
2013-03-30 00:36:14 +01:00
Alessandro Ranellucci
7b7c9f6330
Launch even if config is corrupted. #1067
2013-03-30 00:30:21 +01:00
Alessandro Ranellucci
f5e48a306d
Bugfix: support material and brim didn't work correctly. Includes unit test. #1074
2013-03-30 00:21:09 +01:00
Alessandro Ranellucci
d4119b0eb1
Better bridge direction detection. #1068
2013-03-29 23:49:58 +01:00
Alessandro Ranellucci
5beb2187d3
Bugfix: infill direction wasn't correctly alternated when infilling every 2 layers. #1068
2013-03-29 19:24:08 +01:00
Alessandro Ranellucci
1b79b1cb20
Refactoring: use the clone() method for inflating Surface objects
2013-03-29 19:18:06 +01:00
Alessandro Ranellucci
e563c62094
Replace SetValue with ChangeValue to avoid wxWidgets to fire useless events
2013-03-29 18:56:34 +01:00
Alessandro Ranellucci
d2b451d9a1
Merge branch 'master' into wipe
2013-03-26 16:28:01 +01:00
Alessandro Ranellucci
aae9625a13
Bugfix: solid-infill-below-area wasn't ignored when fill_density = 0, causing solid layers here and there. #1049
2013-03-26 15:47:40 +01:00
Alessandro Ranellucci
2f046799f2
Removed offset() method from Slic3r::Polygon because it only works with ccw polygons
2013-03-26 14:03:24 +01:00
Alessandro Ranellucci
4c41f6c462
Safer safety_offset() for ExPolygons
2013-03-26 13:57:37 +01:00
Alessandro Ranellucci
769ec0cb03
Better clipping of honeycomb paths
2013-03-26 13:04:57 +01:00
Alessandro Ranellucci
843a700e96
Fixes for wipe
2013-03-25 23:06:18 +01:00
Alessandro Ranellucci
4cb36fcbe2
Remove cooling checkbox from simple mode
2013-03-24 21:28:16 +01:00
Alessandro Ranellucci
6bc5de0b5d
Allow custom ranges with layer_height = 0
2013-03-24 15:26:55 +01:00
Alessandro Ranellucci
b7cd362820
Remove scale from G-code comments
2013-03-19 19:16:13 +01:00
Alessandro Ranellucci
7ec6c6ffba
Lower 0.5*w to 0.4*w to fill finer gaps. #1057
2013-03-19 16:08:19 +01:00
Alessandro Ranellucci
34b192fde3
Merge pull request #1059 from cakeller98/Universal_File_Visibility
...
Added "known" as a valid model file type
2013-03-19 08:05:19 -07:00
Alessandro Ranellucci
9c122bda5e
Fix memory leak in avoid_crossing_perimeters. #1044
2013-03-19 16:02:03 +01:00
Alessandro Ranellucci
813aa5b307
Allow drag and drop for OBJ files
2013-03-19 12:25:10 +01:00
Alessandro Ranellucci
fd2a5e894a
Respect perimeter/infill order when multiple extruders are configured but only one is used
2013-03-19 11:58:03 +01:00
Christopher Keller
8bbaafd830
Added "known" as a valid model file type
...
=> 'Known files (*.stl, *.obj, *.amf)|*.stl;*.STL;*.obj;*.OBJ;*.amf;*.AMF;*.xml;*.XML',
When dialog pops up, it can see ALL known file types instead of only stl.
2013-03-18 20:52:55 -07:00
Alessandro Ranellucci
ec5f0635f7
Add wipe in GUI
2013-03-18 21:20:32 +01:00
Alessandro Ranellucci
96f1b7ab57
Merge branch 'master' into wipe
2013-03-18 21:18:24 +01:00
Alessandro Ranellucci
1abd8c9a9e
Remove the 'simplify' handle in ExtrusionPath after the recent refactoring. #1054
2013-03-18 18:03:14 +01:00
Alessandro Ranellucci
f0ac1c704e
Fix test framework detecting dE=0 as retraction
2013-03-18 18:01:01 +01:00
Alessandro Ranellucci
0b81911cff
Bugfix: artifacts near walls. #1049
2013-03-18 17:55:16 +01:00
Alessandro Ranellucci
8ce31c2a2b
Don't exclude any infill under internal bridges; revert infill pattern to rectilinear for internal bridges. #240
2013-03-18 13:32:19 +01:00
Alessandro Ranellucci
7f917671ab
Bugfix: horizontal projection for high-res models might show corrupted result
2013-03-17 15:39:51 +01:00
Alessandro Ranellucci
8d2c651ef2
$surface->thickness was erroneously defaulting to 1 mm
2013-03-17 14:58:10 +01:00
Alessandro Ranellucci
1064c9bb2a
Merge branch 'master' into grow-narrow
...
Conflicts:
lib/Slic3r/Fill.pm
lib/Slic3r/Print/Object.pm
2013-03-17 02:30:20 +01:00
Alessandro Ranellucci
7de8b20bc4
New wipe feature
2013-03-17 02:22:50 +01:00
Alessandro Ranellucci
83065b0789
Bugfix: wrong flow and bad pattern rotation when infill-every-layers was set to an arbitrary high value
2013-03-17 01:10:40 +01:00
Alessandro Ranellucci
04c0caad0b
Fix honeycomb infill overlap with perimeters
2013-03-17 00:57:58 +01:00
Alessandro Ranellucci
537fca47c5
Use solid infill speed for internal bridges; apply slowdown if any; don't use bridge fan settings. #240
2013-03-17 00:42:53 +01:00
Alessandro Ranellucci
700fee14aa
Set honeycomb as default fill pattern, as it works better at low layer heights and makes stronger parts
2013-03-17 00:24:53 +01:00
Alessandro Ranellucci
c999d0c44f
Set default value for first_layer_height to 0.35mm so that first_layer_extrusion_width = 200% works fine even when user sets layer_height to 0.1. A first layer height of 0.35mm works fine for both 0.35 and 0.5 nozzles so it should be fine for most users
2013-03-17 00:22:53 +01:00
Alessandro Ranellucci
78a4ae4835
Use full flow for sparse infill by default
2013-03-17 00:21:17 +01:00
Alessandro Ranellucci
35bd5a3423
New --solid-infill-extrusion-width option
2013-03-17 00:02:31 +01:00
Alessandro Ranellucci
c13d9e9fb3
Don't collapse overhangs too early
2013-03-16 21:51:38 +01:00
Alessandro Ranellucci
0f5064dd32
Untested fix for incomplete honeycomb support material. #1032
2013-03-16 21:10:12 +01:00
Alessandro Ranellucci
25554a345f
Reorder object copies using a nearest neighbor search
2013-03-16 20:56:14 +01:00
Alessandro Ranellucci
cf5adca928
New --resolution option to simplify input models
2013-03-16 19:58:34 +01:00
Alessandro Ranellucci
10b6bc9d15
Removed keep_meshes
2013-03-16 19:39:00 +01:00
Alessandro Ranellucci
f4b8185698
Fixed typo preventing support material to work with new simplify() syntax
2013-03-16 19:11:49 +01:00
Alessandro Ranellucci
db2e76a0df
New option to change perimeter order. #534
2013-03-16 18:56:49 +01:00
Alessandro Ranellucci
33b40eda18
Always fix self-intersecting polygons that Douglas-Peucker might return
2013-03-16 18:42:56 +01:00
Alessandro Ranellucci
0f8ca6191a
Merge branch 'master' into grow-narrow
2013-03-16 16:22:03 +01:00
Alessandro Ranellucci
dc0f706789
Bugfix: simplification of support areas could lead to complex polygons with bad orientation, thus causing wrong pattern clipping. #1032
2013-03-14 14:27:08 +01:00
Alessandro Ranellucci
f528088d31
Merge branch 'master' into grow-narrow
2013-03-13 16:39:57 +01:00
Alessandro Ranellucci
9713b9f524
Fix narrow fills growing
2013-03-13 14:55:58 +01:00
Alessandro Ranellucci
0feef890b1
Use Class::XSAccessor
2013-03-13 01:29:45 +01:00
Alessandro Ranellucci
cab51d4581
One more slight optimization
2013-03-13 01:14:47 +01:00
Alessandro Ranellucci
a412291690
Little optimization
2013-03-13 01:07:06 +01:00
Alessandro Ranellucci
d9b82c79da
Grow narrow infill regions into void - to be tested more
2013-03-13 01:03:54 +01:00
Alessandro Ranellucci
6058384978
Fixed regression causing crash when support material threshold angle was defined. #1048
2013-03-12 19:39:43 +01:00
Alessandro Ranellucci
5c1336d2de
Clarify that min Z, max Z and layer height are supposed to be expressed in mm
2013-03-12 10:28:51 +01:00
Alessandro Ranellucci
a5e6340004
Workaround for HideRowLabels() missing in wxWidgets 2.8. #770
2013-03-11 20:00:12 +01:00
Alessandro Ranellucci
999af84c54
Don't make internal bridges when fill_density == 1. #1045
2013-03-11 18:41:12 +01:00
Alessandro Ranellucci
0df8398a39
Use concentric infill for internal bridges. #240
2013-03-11 18:38:32 +01:00
Alessandro Ranellucci
0eecf33198
Bugfix: narrow solid shells were collapsed when spacing was added before generating infill, so we grow them
2013-03-11 18:37:01 +01:00
Alessandro Ranellucci
b73c301c55
Bugfix: double lift at toolchange. #953
2013-03-11 17:06:05 +01:00
Alessandro Ranellucci
0326962d11
Merge branch 'new-extra-perimeters'
2013-03-11 14:24:02 +01:00
Alessandro Ranellucci
e809a5bdcc
Added support for expolygons in Slic3r::SVG
2013-03-11 14:23:45 +01:00
Alessandro Ranellucci
b7945ac790
Finished new extra perimeters implementation
2013-03-11 14:23:16 +01:00
Alessandro Ranellucci
428cd7867d
Missing bit
2013-03-11 12:47:27 +01:00
Alessandro Ranellucci
74e21d7a04
New implementation of extra perimeters - to test
2013-03-10 19:08:36 +01:00
Alessandro Ranellucci
964accb588
Typo
2013-03-10 19:07:41 +01:00
Alessandro Ranellucci
2942485a94
New option to make infill before perimeters. #1039
2013-03-10 18:15:44 +01:00
Alessandro Ranellucci
ab3d1ac820
Give priority to infill extruder if it was used last. #940
2013-03-10 17:40:19 +01:00
Alessandro Ranellucci
107f48d894
Reduce toolchanges by giving priority to last extruder on layer change. #940
2013-03-10 17:28:03 +01:00
Alessandro Ranellucci
dac168eff0
Do each island completely if avoid_crossing_perimeters is enabled. #278
2013-03-10 16:09:03 +01:00
Alessandro Ranellucci
f10a4787b2
Fix layer ordering when printing objects with different layer heights
2013-03-10 15:36:52 +01:00
Alessandro Ranellucci
f670acb4b1
Slice a single object with multiple layer heights. :-)
2013-03-10 14:58:49 +01:00
Alessandro Ranellucci
d1acc511b3
Refactor ObjectDialog into a tab panel
2013-03-10 12:46:54 +01:00
Alessandro Ranellucci
6a0ba97f0e
Move ObjectDialog to a separate file
2013-03-10 12:33:10 +01:00
Alessandro Ranellucci
d2152a53a0
Missing tooltip for extra perimeters
2013-03-10 12:30:43 +01:00
Alessandro Ranellucci
17cbca5e06
Factor out layer height in support material generation
2013-03-10 12:22:40 +01:00
Alessandro Ranellucci
2ab5fa9c72
Factor out layer height from combine_infill()
2013-03-10 12:08:18 +01:00
Alessandro Ranellucci
2275de9f0d
Factored out the layer height logic
2013-03-10 11:37:16 +01:00
Alessandro Ranellucci
e9c7460c11
New --bridge-acceleration option
2013-03-09 20:31:09 +01:00
Alessandro Ranellucci
2acda9973e
Don't apply acceleration settings to travel moves
2013-03-09 20:28:03 +01:00
Alessandro Ranellucci
b7b89ff7f2
Bugfix: *-acceleration options didn't work in CLI
2013-03-09 20:21:05 +01:00
Alessandro Ranellucci
460e169c67
New option to disable retraction on layer change
2013-03-09 20:05:43 +01:00
Alessandro Ranellucci
e71bf48463
Add a command to lift nozzle in default start G-code
2013-03-09 19:51:09 +01:00
Alessandro Ranellucci
d50e0af548
Make sure the inwards move after last perimeter loop doesn't exceed object boundary
2013-03-09 17:15:45 +01:00
Alessandro Ranellucci
caa79583ff
Tiny optimization
2013-03-09 17:08:17 +01:00
Alessandro Ranellucci
fa41e15c68
Fixed regression causing thin walls to be processed twice, thus producing overlapping straight paths and zigzag. #1035
2013-03-09 17:07:11 +01:00
Alessandro Ranellucci
a2702082b2
Merge pull request #962 from scottp/issue_885b
...
Add defaults into Tooltips from #885
2013-03-09 07:48:20 -08:00
Alessandro Ranellucci
9247b3e9f4
New --no-plater and --gui-mode options. #604
2013-03-09 16:43:09 +01:00
Alessandro Ranellucci
af50272b3b
Refactor simple mode definitions to dedicated SimpleTab classes
2013-03-09 16:27:18 +01:00
Alessandro Ranellucci
5477d66902
Advertise the expert mode in simple mode
2013-03-09 14:55:07 +01:00
Alessandro Ranellucci
46f35e39f6
Some more tweaks
2013-03-08 23:34:57 +01:00
Alessandro Ranellucci
0748e088a0
Reorder options in simple mode
2013-03-08 23:07:14 +01:00
Alessandro Ranellucci
84f4f098ca
Fix cooling and load in simple-mode. #1001
2013-03-08 22:58:28 +01:00
Alessandro Ranellucci
b901e1f6c8
Merge branch 'master' into simple-mode
2013-03-08 22:28:13 +01:00
Alessandro Ranellucci
4fc435f0fd
Bugfix: retract speed was applied to travel
2013-03-08 17:52:33 +01:00
Alessandro Ranellucci
f494335f77
Bugfix: not all the calls to travel_to() were updated
2013-03-08 13:50:50 +01:00
Alessandro Ranellucci
2f192bddca
Make tests happy
2013-03-07 16:24:25 +01:00
Alessandro Ranellucci
97e864699e
New top-infill-extrusion-width option
2013-03-07 16:00:58 +01:00
Alessandro Ranellucci
36d24ccb0b
Infill refactoring and cleanup complete
2013-03-07 15:47:32 +01:00
Alessandro Ranellucci
d928f005e6
Some incomplete work for cleaner infill logic
2013-03-05 20:03:46 +01:00
Alessandro Ranellucci
a9df56670f
Bugfix: internal-bridge regions were not touching perimeters
2013-03-05 19:33:06 +01:00
Alessandro Ranellucci
37810f777f
Make only_retract_when_crossing_perimeters work with avoid_crossing_perimeters
2013-03-05 17:30:27 +01:00
Alessandro Ranellucci
72613ae2b4
Enable only_retract_when_crossing_perimeters by default
2013-03-05 15:01:45 +01:00
Alessandro Ranellucci
70092a9cf5
Apply only_retract_when_crossing_perimeters to all infills
2013-03-04 23:37:58 +01:00
Mike Sheldrake
28467b68e0
typo - fix wrong bridge direction #621
...
fixes two out of three reported in #621 (but not the first one)
likely the same issue in #706 and #1003
2013-02-27 15:16:07 -08:00
Alessandro Ranellucci
a6243124a9
Merge pull request #984 from giseburt/origin_master
...
Fix for Replicator 1 not finishing builds.
2013-02-27 02:37:45 -08:00
Alessandro Ranellucci
fafad0fd81
Code for memory usage statistics
2013-02-27 11:26:52 +01:00
Alessandro Ranellucci
bb83f070ae
Load threads::shared before Wx. #1018
2013-02-27 11:08:08 +01:00
Alessandro Ranellucci
919d1131f8
Use nearest-neighbor search for internal perimeters too. #1025
2013-02-27 11:04:14 +01:00
Alessandro Ranellucci
c3d90a1ff8
Rename $layer to $layerm in Slic3r::Fill too for consistency
2013-02-27 10:44:42 +01:00
Alessandro Ranellucci
a9090688f9
Refactor bridge flow to Slic3r::Flow::Bridge class
2013-02-27 10:43:50 +01:00
Alessandro Ranellucci
d00c2882c4
Remove debug line slipped into last commit
2013-02-27 10:30:05 +01:00
Alessandro Ranellucci
bf9fe1b505
Bugfix: internal bridge surfaces were incorrectly merged with other internal solid surfaces, causing suboptimal results
2013-02-27 01:30:32 +01:00
Alessandro Ranellucci
8ce7b13db5
Fixed regression in is_printable() - needs unit test
2013-02-26 20:54:40 +01:00
Alessandro Ranellucci
37be4f7319
Some cleanup for detect_surfaces_type()
2013-02-26 20:52:13 +01:00
Alessandro Ranellucci
f4e8cdbf36
Better logic for extra perimeters
2013-02-26 20:00:05 +01:00
Alessandro Ranellucci
038737abe6
Bugfix: minimum flow for low layer heights was still too low
2013-02-26 14:15:05 +01:00
Alessandro Ranellucci
7412d4a687
Bugfix: manifoldness error triggered with multi-volume AMF files. #1019
2013-02-24 18:17:08 +01:00
Alessandro Ranellucci
bd76e7677c
Adjust extra perimeters
2013-02-24 17:04:19 +01:00
Alessandro Ranellucci
c3dde74776
Fix brim and extra perimeters after recent changes to ->slices
2013-02-24 16:40:14 +01:00
Alessandro Ranellucci
de0c2febd9
Remove useless lines
2013-02-23 23:50:46 +01:00
Alessandro Ranellucci
08a72c0824
Use bridge math for the first solid infill layer above sparse infill. #240
2013-02-23 21:39:13 +01:00
Alessandro Ranellucci
3b1e921171
Slight changes to the defaults
2013-02-23 19:14:41 +01:00
Alessandro Ranellucci
0634437364
Keep the full geometries in $layer->slices, including thin walls
2013-02-23 18:21:29 +01:00
Alessandro Ranellucci
504962712b
Bugfix: when using low layer heights and support material, the contact regions were generated with a negative height. #1013
2013-02-23 17:40:38 +01:00
Alessandro Ranellucci
3eedd4bbed
Fixed regression in support material after recent flow refactoring. #1012
2013-02-23 16:08:29 +01:00
Alessandro Ranellucci
72df796185
Bugfix: failure in launching on Windows with non-ASCII characters in username. #1011
2013-02-22 18:40:00 +01:00
Alessandro Ranellucci
28638019ae
Bugfix: perimeter/infill overlap was calculated regardless of the infill extrusion width. #994
2013-02-22 18:23:23 +01:00
Alessandro Ranellucci
bec2371604
Fix regression introduced in 91bcfc8a74
2013-02-22 16:56:43 +01:00
Alessandro Ranellucci
5eade0f9e1
Don't validate the number of layers for infill combination, just limit it automatically. #993
2013-02-22 16:24:24 +01:00
Alessandro Ranellucci
91bcfc8a74
Remove $Slic3r::flow and $Slic3r::first_layer_flow
2013-02-22 16:08:11 +01:00
Alessandro Ranellucci
b9c84490b8
Get rid of most calls to $Slic3r::flow
2013-02-19 12:37:26 +01:00
Alessandro Ranellucci
6dc62d3cf2
Disable extra perimeters if fill density is zero as they wouldn't be supported by anything and would just float inside the object. infill_only_where_needed should be the method of choice for hollow objects
2013-02-19 12:37:26 +01:00
Mike Sheldrake
c2f04f2861
avoid overlap of single layer and multilayer fill
...
A single-layer rectilinear or honeycomb fill under a low slope
wall/ceiling or extra perimeter will stick out from under the
overhang, because those fills get extended beyond their fill_surface
boundaries to purposely overlap perimeters. This causes interference
with multil-layer fills. This commit clips the single layer fill
boundaries a bit more where they interface with multi-layer fill
boundaries, to avoid overlap.
2013-02-18 07:26:19 -08:00
Mike Sheldrake
9a86edc70c
account for extrusion width when clearing layers for combined infill
...
Otherwise you get extraneous fill up against sloped walls in regions
of layers that should not have fill, like in #834 .
2013-02-16 07:53:47 -08:00
Alessandro Ranellucci
c9b506fa02
New simpler and more robust implementation of infill every 'n' layers
2013-02-10 12:40:43 +01:00
Alessandro Ranellucci
cac79c0575
New option to only infill where strictly needed for supporting ceilings
2013-02-09 23:36:32 +01:00
Alessandro Ranellucci
cf8cfc1380
Bugfix: angle threshold was considered even when enforcing support
2013-02-09 21:49:00 +01:00
Robert Giseburt
6c12bd32ad
Fix for Replicator 1 not finishing builds.
...
If the progress reaches 100% before last layer, the firmware erroneously stops reading the file.
2013-02-06 22:32:37 -06:00
Alessandro Ranellucci
26a3cd5542
Refactor chained_path(), add chained_path_items() and chained_path_points()
2013-02-06 12:03:53 +01:00
Alessandro Ranellucci
e593a30fc7
Skip support material for one-layer objects
2013-02-06 10:40:08 +01:00
Alessandro Ranellucci
4f91bed904
Optimize cycling in get_layer_range()
2013-02-05 21:59:18 +01:00
Alessandro Ranellucci
73a661e6c1
shortest_path() in MotionPlanner was actually correctly named shortest_path()
2013-02-05 19:41:56 +01:00
Alessandro Ranellucci
090e3b1fe3
Rename shortest_path to chained_path, which reflects its algorithm more correctly
2013-02-05 17:27:45 +01:00
Alessandro Ranellucci
11637d527a
Bugfix: avoid-crossing-perimeters was failing on layers only containing single walls. #978
2013-02-04 19:33:30 +01:00
Alessandro Ranellucci
8efe46e58d
New option to enforce support material on a given number of layers to improve adhesion of objects with poor footprint
2013-02-04 15:48:57 +01:00
Alessandro Ranellucci
c8100ed099
Disable randomize starting points by default
2013-02-04 15:05:56 +01:00
Alessandro Ranellucci
7d08796b0a
Remove sporadic duplicate useless lines. #772
2013-02-04 14:27:23 +01:00
Alessandro Ranellucci
9222526e03
Customizable number of interface layers for support material and raft
2013-02-03 17:23:50 +01:00
Alessandro Ranellucci
acada05068
Merge branch 'raft'
2013-02-02 16:17:05 +01:00
Alessandro Ranellucci
c7b4d99d7e
Generate raft automatically even when support material is disabled
2013-02-02 16:16:43 +01:00
Alessandro Ranellucci
02c0f3658f
Use 50% density for support base flange
2013-02-02 15:37:09 +01:00
Alessandro Ranellucci
d3727a1699
Add ability to have cross-hatched rectilinear support material. #509
2013-02-02 00:14:45 +01:00
Alessandro Ranellucci
547dfb857d
Workaround for Boost clipping not being idempotent and causing lack of support material
2013-02-01 23:45:46 +01:00
Alessandro Ranellucci
eae1e7adc2
Make a solid base below support material on first layer
2013-02-01 22:13:12 +01:00
Alessandro Ranellucci
1de0169910
Multithreaded perimeter generation. #154
2013-01-31 15:44:55 +01:00
Scott Penrose
9d086f027a
Add defaults into Tooltips from #885
2013-01-30 09:53:22 +11:00
Alessandro Ranellucci
177f1a9bf0
New raft_layers option. #123
2013-01-28 14:12:01 +01:00
Alessandro Ranellucci
a016a06fa6
Merge branch 'avoid-crossing-perimeters'
...
Conflicts:
lib/Slic3r/GCode.pm
2013-01-28 10:43:58 +01:00
Alessandro Ranellucci
e8cb1f4528
Slight addition to avoid_crossing_perimeters tooltip
2013-01-28 10:42:24 +01:00
Alessandro Ranellucci
721b61e798
Require Boost::Geometry::Utils 0.06
2013-01-28 00:34:09 +01:00
Alessandro Ranellucci
2963e54d21
Use the faster polygon_multi_linestring_intersection()
2013-01-28 00:32:19 +01:00
Alessandro Ranellucci
ae201c8f41
Optimization: avoid calculating square roots if not needed
2013-01-28 00:18:55 +01:00
Alessandro Ranellucci
6cb891f2db
Use Boost::Geometry::Utils for Douglas-Peucker
2013-01-28 00:09:19 +01:00
Alessandro Ranellucci
4c8c725eec
Add a wkt() method to ExPolygon
2013-01-28 00:02:34 +01:00
Alessandro Ranellucci
ddaeaa7591
Fix last_pos shifting and add unit test
2013-01-27 13:08:13 +01:00
Alessandro Ranellucci
50526dea5a
Fix last_pos shifting and add unit test
2013-01-27 13:06:45 +01:00
Alessandro Ranellucci
ad48fdc7f9
Fix external motionplanner too
2013-01-27 12:48:16 +01:00
Alessandro Ranellucci
f1230312e3
Fixes for merge issues
2013-01-26 23:55:47 +01:00
Alessandro Ranellucci
61b164b539
Merge branch 'master' into avoid-crossing-perimeters
...
Conflicts:
lib/Slic3r/GCode.pm
lib/Slic3r/Print.pm
2013-01-26 21:45:17 +01:00
Alessandro Ranellucci
4c62c1b570
Support .gco extension too. #957
2013-01-26 21:40:20 +01:00
Mike Sheldrake
bc61656057
harmless misplaced semicolon
2013-01-26 09:31:28 -08:00
Mike Sheldrake
599d76b70b
avoid DBus related crash on Ubuntu #954
...
An undocumented feature of Net::DBus->session() is that it returns
the same connection object it creates the first time it's called for
all subsequent calls. Somehow this exposes us to a bug where unref()
is called on that object too many times, causing a segfault.
Undefining the cached object after we've used it once avoids this.
2013-01-25 12:29:44 -08:00
Alessandro Ranellucci
18280da1b3
Bugfix: the non-manifold warning was spitting out wrong coordinates
2013-01-25 18:02:01 +01:00
Alessandro Ranellucci
f555a1ecc2
Replace 'Less' with 'Fewer' in plater. #944
2013-01-23 19:16:57 +01:00
Alessandro Ranellucci
94bb1e54bb
Raise max temperatures (in GUI) to 400°C
2013-01-23 11:10:46 +01:00
Mike Sheldrake
65ef3b35d9
limit layer requests to object->layer_count when preparing skirt #901
...
Each object on the plater was being queried for points for
producing the skirt for all skirt layers, even when the object was
shorter than the skirt.
layers of the print
2013-01-18 08:36:01 -08:00
Alessandro Ranellucci
09bdd2ea5d
Bump version number
2013-01-17 17:44:56 +01:00
Alessandro Ranellucci
71052433de
Releasing 0.9.8
2013-01-17 15:50:45 +01:00
Alessandro Ranellucci
73c70021df
Change toolchange and G92 E0 order for makerbot and sailfish G-code flavors. #855
2013-01-17 15:02:40 +01:00
Alessandro Ranellucci
177347137f
New G-code flavor for Sailfish (thanks to fros1y for working on it). #826
2013-01-17 14:56:31 +01:00
Alessandro Ranellucci
8001059390
Add Mike Sheldrake in the About window
2013-01-17 14:13:25 +01:00
Alessandro Ranellucci
92feebf5fe
Fixed regression introduced in 4d8757bf5d causing crash during support material generation
2013-01-17 12:32:57 +01:00
Alessandro Ranellucci
4d8757bf5d
Interface support layers were clipped badly. Also, reduce simplification of the clipping boundaries. #583
2013-01-17 11:59:14 +01:00
Alessandro Ranellucci
4fc6fc5ab6
Increase default value for retract_length_toolchange
2013-01-17 11:51:00 +01:00
Alessandro Ranellucci
0ddd6d9e55
Require Math::Clipper 1.17
2013-01-17 11:11:22 +01:00
Alessandro Ranellucci
954520cba5
Enable cooling by default
2013-01-17 10:40:45 +01:00
Alessandro Ranellucci
ecc7e4560e
Don't fill gaps if fill density is 0. #915
2013-01-17 10:39:05 +01:00
Mike Sheldrake
f3a1221039
per-thread clipper object for parallel support generation #888
2013-01-16 06:00:04 -08:00
Mike Sheldrake
241dff00e2
Merge branch '834-every-n-fill-frags' #834
2013-01-16 02:24:47 -08:00
Mike Sheldrake
85934e1738
use infill flow spacing, not perimeter, for combine_infill() clip offsets
2013-01-15 22:13:11 -08:00
Alessandro Ranellucci
4bff4d0d50
Ignore perimeter_acceleration and infill_acceleration if their values are 25 and 50 to handle legacy configs gracefully.
2013-01-15 12:52:22 +01:00
Mike Sheldrake
bce3e96210
extraneous fill against sloped walls with fill every N layers #834
...
Polygons used for N x depth fill surfaces need to be offset
by flow spacing before they are reused to clip lower fill surfaces.
Otherwise thin fill sections remain on clipped layers against sloping
walls, and the N x depth fill collides with them.
2013-01-14 21:18:31 -08:00
Mike Sheldrake
68fc91d854
offset miter limit to 3 - 801 828 836 851 875 - spikes and pimples
...
Was set to 10 to address 801. Setting to 3 has the same effect for 801,
and avoids spike artifacts that are likely causing "spike and pimple"
problems in the referenced issues.
2013-01-13 02:50:49 -08:00
Alessandro Ranellucci
ad9be0e4d7
Bugfix: crash when reading/writing files to paths containing non-ASCII characters on Windows. #651 #865
2013-01-13 10:18:34 +01:00
Alessandro Ranellucci
48e00a4c40
Merge branch 'master' into avoid-crossing-perimeters
...
Conflicts:
lib/Slic3r/GCode.pm
lib/Slic3r/GUI/Plater.pm
lib/Slic3r/Print.pm
lib/Slic3r/SVG.pm
2013-01-12 19:00:18 +01:00
Mike Sheldrake
73aae07e74
842, 847 slightly enlarge a clip polygon to counteract integer truncation
...
Geomery in referenced issues triggered Clipper problems, but also
pointed to a situation where integer truncation (as coordinates pass
into Clipper) might be shrinking a clip polygon in a way that leaves
degenerate or unwanted thin clip results. Growing the clip polygon by 2
is expected to overcome any issues caused by truncation of floats.
2013-01-11 10:15:42 -08:00
Alessandro Ranellucci
3d03faf0b2
Remove leftover M501
2013-01-10 17:19:38 +01:00
Alessandro Ranellucci
32fd58d531
Acceleration control. #185
2013-01-10 15:29:40 +01:00
Alessandro Ranellucci
7239ca18c1
Simple mode
2013-01-03 15:49:20 +01:00
Alessandro Ranellucci
cf4c090208
Added Preferences dialog
2013-01-02 20:30:48 +01:00
Alessandro Ranellucci
34e047205a
Automatic detection of support material threshold angle
2013-01-02 19:40:48 +01:00
Alessandro Ranellucci
cbd298bc36
Alter extrusion width automatic calculation to take "native flow" into account
2013-01-02 19:22:51 +01:00
Alessandro Ranellucci
30d9b2e508
Refactoring: initialize all layers at once and avoid duplication of slicing height math. #637
2013-01-01 23:28:48 +01:00
Alessandro Ranellucci
1774143011
Bugfix: PlanePath fill patterns were not working anymore. #880
2012-12-31 14:11:36 +01:00
Alessandro Ranellucci
141a8d3989
Bugfix: some holes being closed incorrectly. #858
2012-12-30 17:57:30 +01:00
Alessandro Ranellucci
6e6bc74636
Added failing test case for troubleshooting unexpected filled holes. #858
2012-12-30 16:27:20 +01:00
Alessandro Ranellucci
0da71dbdfa
Fix regression causing wrong number of solid shells when using fill_density = 0 (includes regression test)
2012-12-23 20:20:17 +01:00
Alessandro Ranellucci
e59ed7efb7
New toolchange_gcode option. #547
2012-12-23 16:29:08 +01:00
Alessandro Ranellucci
15f07197d8
Don't store ->surfaces anymore. Save memory, save time
2012-12-22 23:57:39 +01:00
Alessandro Ranellucci
5930267de9
Bugfix: some top/bottom solid shells are not treated as solid. #689
2012-12-21 20:25:48 +01:00
Alessandro Ranellucci
8cd8e8b209
Merge branch 'test-dual-retraction'
2012-12-21 15:23:07 +01:00
Alessandro Ranellucci
dc4ada2374
Fix retraction tests and fix retract_extra_length and lift in multiple extruders environments
2012-12-21 15:14:44 +01:00
Alessandro Ranellucci
701c98c5a7
Export Slic3r::Test::_eq()
2012-12-21 13:25:03 +01:00
Alessandro Ranellucci
d5537e7797
Enable retraction for support material too, but only when moving away from support islands. #831
2012-12-20 18:47:40 +01:00
Alessandro Ranellucci
bf603b0221
Fixed regression causing inefficient paths during infill
2012-12-20 18:10:20 +01:00
Alessandro Ranellucci
dcc0ce78db
Fix warning
2012-12-20 17:03:50 +01:00
Alessandro Ranellucci
ea304a4803
Bugfix: custom layer G-code was applied before Z change, and not after like it was documented. #869
2012-12-20 17:01:01 +01:00
Alessandro Ranellucci
b70404bb23
Disable gap filling if gap fill speed is set to zero
2012-12-17 19:55:25 +01:00
Alessandro Ranellucci
1a3497b71d
Add tests for vibration limiting and fix implementation. Also includes a fix in set_shift()
2012-12-09 18:33:25 +01:00
Alessandro Ranellucci
4078bb0476
Fix error when vibration limit is disabled
2012-12-06 10:54:28 +01:00
Alessandro Ranellucci
142a6cc4eb
Add --vibration-limit back to CLI usage and disable it by default
2012-12-05 17:57:35 +01:00
Alessandro Ranellucci
ca0aa5c287
Apply vibration limit to every move except perimeters
2012-12-05 16:32:50 +01:00
Alessandro Ranellucci
25960a33e0
Put vibration limit back in GUI
2012-12-05 15:08:17 +01:00
Alessandro Ranellucci
cf32cd6510
Implement vibration limit using G4 pauses
2012-12-05 15:03:36 +01:00
Alessandro Ranellucci
f001374c6e
New implementation of the little inwards move before leaving a loop. #186
2012-12-05 11:31:35 +01:00
Alessandro Ranellucci
283809f5c2
No need for a role to identify small perimeters
2012-12-05 10:47:41 +01:00
Alessandro Ranellucci
ac6dc67e6a
Tidy
2012-12-05 01:12:50 +01:00
Alessandro Ranellucci
accc598eb5
Revert "Experimental feature: make a little move inwards by 45° after finishing the external perimeter and before retracting. #186 "
...
This reverts commit c57e94c065
2012-11-29 19:16:07 +01:00
Alessandro Ranellucci
b495e15d7f
Fix plater slowness after the introduction of the vertical projection
2012-11-29 19:13:52 +01:00
Alessandro Ranellucci
93310a6a81
Fix bounding_box_center()
2012-11-24 00:15:02 +01:00
Alessandro Ranellucci
116ab446e3
Show vertical projection instead of convex hull for objects with <= 2000 facets. #780
2012-11-24 00:13:04 +01:00
Alessandro Ranellucci
e6afebb982
Bump version number
2012-11-23 19:37:41 +01:00
Alessandro Ranellucci
452b62e53d
Releasing 0.9.7
2012-11-23 18:38:50 +01:00
Alessandro Ranellucci
12873e973b
One more missing bit for gap_fill_speed
2012-11-23 18:37:47 +01:00
Alessandro Ranellucci
556e59bbe4
Last commit erroneously reverted gap fill speed
2012-11-23 17:41:15 +01:00
Alessandro Ranellucci
0f0992e39a
Speed for support material. #813
2012-11-23 17:20:26 +01:00
Alessandro Ranellucci
d6d96391a9
Avoid overextrusion when support material spacing is configured to < the extrusion spacing. #821
2012-11-23 17:15:52 +01:00
Alessandro Ranellucci
e7b307df02
Expose gap_fill_speed in GUI
2012-11-23 17:09:59 +01:00
Alessandro Ranellucci
5dba02fdeb
New separate speed setting for gap fill. #785
2012-11-23 11:25:02 +01:00
Alessandro Ranellucci
68e302fe27
Fix exporting G-code
2012-11-23 11:24:04 +01:00
Alessandro Ranellucci
21a6219b62
Disable vibration limit. #785
2012-11-23 11:14:06 +01:00
Alessandro Ranellucci
2abf2be781
New testing framework
2012-11-21 20:41:14 +01:00
Alessandro Ranellucci
8ae96a8868
Only apply vibration limit to gaps fill while it's not very mature to work with long segments
2012-11-21 19:27:38 +01:00
Alessandro Ranellucci
fc399d60e2
Raise the miter limit to avoid squaring corners too easily. #801
2012-11-20 17:43:20 +01:00
Alessandro Ranellucci
cd892fdce8
Connect zigzag gaps fill paths to benefit from simplification
2012-11-19 18:57:42 +01:00
Alessandro Ranellucci
e91320e031
Fix rotation for threaded perls
2012-11-19 18:31:41 +01:00
Alessandro Ranellucci
124a1fd84e
Raise default frequency limit to 25Hz
2012-11-19 18:03:49 +01:00
Alessandro Ranellucci
de8a845d81
Disable retraction for support material
2012-11-19 18:03:20 +01:00
Alessandro Ranellucci
5678cd562c
Fix preview after rotation in plater
2012-11-19 17:39:16 +01:00
Alessandro Ranellucci
99c942b5ea
Merge branch 'vibration-limit'
2012-11-19 15:54:50 +01:00
Alessandro Ranellucci
3c7321ab80
Bugfix: some retractions between objects/copies were skipped. #786
2012-11-19 15:34:52 +01:00
Alessandro Ranellucci
300734db38
Emit M106 S0 instead of M107 for Teacup
2012-11-19 15:30:55 +01:00
Alessandro Ranellucci
183736dd9a
Infill flow for bottom layer was calculated incorrectly when first_layer_height != layer_height
2012-11-19 12:37:05 +01:00
Alessandro Ranellucci
de0640603a
Append full config when --gcode-comments is enabled
2012-11-18 19:53:52 +01:00
Alessandro Ranellucci
a66e8e547d
Apply Douglas-Peucker to all paths before generating G-code
2012-11-18 18:00:33 +01:00
Alessandro Ranellucci
e119cee66c
Don't emit warnings on unknown options
2012-11-18 17:42:52 +01:00
Alessandro Ranellucci
c99ff0cfe2
Apply Douglas-Peucker to all paths before generating G-code
2012-11-18 17:38:08 +01:00
Alessandro Ranellucci
08700aa942
Keep bridge flow unchanged even with the new overlapping spacing
2012-11-18 15:44:47 +01:00
Alessandro Ranellucci
427e3c1720
Keep bridge flow unchanged even with the new overlapping spacing
2012-11-18 15:42:59 +01:00
Alessandro Ranellucci
7a87a76391
Refactor frequency limit to avoid processing G-code
2012-11-18 15:28:13 +01:00
Alessandro Ranellucci
008633f013
Working implementation of frequency limit
2012-11-18 12:23:11 +01:00
Alessandro Ranellucci
f3164594eb
More incomplete work
2012-11-18 11:33:53 +01:00
Alessandro Ranellucci
72007c4f6a
Rewrite frequency limiting code
2012-11-17 18:07:13 +01:00
Alessandro Ranellucci
600e951fd8
Completed vibration limit
2012-11-17 12:08:19 +01:00
Alessandro Ranellucci
96dd106f61
Initial work for limiting vibrations
2012-11-17 10:40:15 +01:00
Alessandro Ranellucci
8d557bee8c
Bugfix: AMF export was not working anymore. #799
2012-11-16 22:41:54 +01:00
Alessandro Ranellucci
7310cec087
Remove one more unused line
2012-11-16 22:09:32 +01:00
Alessandro Ranellucci
ed50aefa71
Remove unused code
2012-11-16 22:08:14 +01:00
Alessandro Ranellucci
ac5be309e3
Do not call merge_continuous_lines() anymore
2012-11-16 19:20:46 +01:00
Alessandro Ranellucci
aff0898f35
Typo
2012-11-16 18:24:09 +01:00
Alessandro Ranellucci
e13fe1d636
Raise overlap factor to 1 >:-)
2012-11-16 18:11:06 +01:00
Alessandro Ranellucci
86f5cb8654
Previous commit about bridge spacing was incomplete
2012-11-16 18:10:09 +01:00
Alessandro Ranellucci
a81377d684
Apply overlap factor to bridges too
2012-11-16 13:18:06 +01:00
Alessandro Ranellucci
1c2bc94d5a
Bugfix: only_retract_when_crossing_perimeters might cause some missed retractions when printing multiple copies of the same object. #786
2012-11-16 12:39:55 +01:00
Alessandro Ranellucci
a1a12ffe8e
Allow setting top-solid-layers and bottom-solid-layers to 0 independently
2012-11-16 12:37:47 +01:00
Alessandro Ranellucci
06b475a4ed
Clone last_pos before storing it otherwise it will be translated. #786
2012-11-16 11:05:45 +01:00
Alessandro Ranellucci
b625c3b2b2
Simplify gaps fills to avoid some shaking
2012-11-16 10:47:42 +01:00
Alessandro Ranellucci
a5a0f32e19
Expose all SLIC3R_* environment variables as placeholders. #781
2012-11-16 10:07:30 +01:00
Alessandro Ranellucci
580e36eb25
Raise offset scale factor back to 100000 now that Clipper was updated
2012-11-15 10:09:29 +01:00
Alessandro Ranellucci
d3629a3a44
Require Math::Clipper 1.15. #779
2012-11-13 11:53:02 +01:00
Alessandro Ranellucci
8f0e388c5b
Bump version number
2012-11-07 23:22:12 +01:00
Alessandro Ranellucci
af78469231
Releasing 0.9.5
2012-11-07 23:07:43 +01:00
Alessandro Ranellucci
93bb2c1056
Bugfix: fatal error when using brim and no skirt. #784
2012-11-07 23:06:32 +01:00
Alessandro Ranellucci
2e3110d2e4
Possible (or at least partial) workaround for the current Clipper segfault. #779
2012-11-07 15:23:01 +01:00
Alessandro Ranellucci
2ef90562ce
Fixed regression causing first two layers to be infilled with parallel lines
2012-11-06 22:16:01 +01:00
Alessandro Ranellucci
e21c806ee9
New wkt() method for debugging
2012-11-06 20:31:50 +01:00
Alessandro Ranellucci
1db614a5a9
Revert "Use G92 to apply Z offset. #486 " #778
2012-11-06 20:04:44 +01:00
Alessandro Ranellucci
ab2b31672f
Fixed regression causing a long string between copies
2012-11-06 19:54:21 +01:00
Alessandro Ranellucci
68c2ac601b
Bump version number
2012-11-05 23:38:55 +01:00
Alessandro Ranellucci
ed100c477c
Releasing 0.9.4
2012-11-05 17:52:08 +01:00
Alessandro Ranellucci
0bff8ad576
Bugfix: some multimaterial files generated a fatal error
2012-11-05 15:59:31 +01:00
Alessandro Ranellucci
0a912c6316
Only apply min_skirt_length on bottom layer
2012-11-05 14:26:55 +01:00
Alessandro Ranellucci
68e1edab80
Require Math::Clipper 1.14 and increase scale factor for offset(). #720
2012-11-05 00:17:46 +01:00
Mark Hindess
705d6b3179
Quick fix for support material.
2012-11-02 22:39:08 +00:00
Alessandro Ranellucci
d67c07bd47
Fix typo causing incomplete honeycomb infill after recent refactoring
2012-11-01 18:32:35 +01:00
Alessandro Ranellucci
93a8391e18
Alternate gaps fill direction
2012-11-01 11:53:18 +01:00
Alessandro Ranellucci
37c0b45187
Detect gaps even after the desired number of perimeters has been generated
2012-11-01 11:51:52 +01:00
Alessandro Ranellucci
cb4ede7f9e
Do not pass the Print object to SVG::output anymore
2012-11-01 11:34:53 +01:00
Alessandro Ranellucci
554d10c854
Only put ExtrusionPath objects in ExtrusionPath::Collection (no ExtrusionLoop objects)
2012-10-31 19:08:29 +01:00
Alessandro Ranellucci
d4ccd39ad3
Minor code cleanup
2012-10-30 15:53:01 +01:00
Alessandro Ranellucci
92ab53868e
Remove unused methods
2012-10-30 15:49:11 +01:00
Alessandro Ranellucci
44d91774a6
Get rid of useless Slic3r::Fill instances
2012-10-30 15:38:17 +01:00
Alessandro Ranellucci
cec7bf815c
Get rid of the ExtrusionLoop objects in concentric filler
2012-10-30 15:29:13 +01:00
Alessandro Ranellucci
20e73face2
Get rid of max_print_dimension in filler objects
2012-10-30 15:09:54 +01:00
Alessandro Ranellucci
6c97e588b1
Don't require the print object in filler objects
2012-10-30 14:34:41 +01:00
Alessandro Ranellucci
5943114574
Only take layer_id instead of layer in filler objects
2012-10-30 14:25:48 +01:00
Alessandro Ranellucci
61047f0df5
Define perimeter/infill overlap over spacing instead of width and increase it slightly to compensate
2012-10-30 14:21:59 +01:00
Alessandro Ranellucci
610862a97f
Use the actual flow spacing for clipping concentric loops
2012-10-30 14:17:30 +01:00
Alessandro Ranellucci
0a5016a509
Cleaner usage of the PI constant
2012-10-30 14:15:48 +01:00
Alessandro Ranellucci
25d88bddff
Remove the change_layer method
2012-10-30 14:11:32 +01:00
Alessandro Ranellucci
52ed2c6ea4
Make flow_spacing required for ExtrusionLoop objects too
2012-10-30 14:07:50 +01:00
Alessandro Ranellucci
be7e211bb6
Make flow_spacing required for ExtrusionPath objects
2012-10-30 14:07:01 +01:00
Alessandro Ranellucci
37637c34f5
Refactor shortest_path
2012-10-30 13:59:33 +01:00
Alessandro Ranellucci
4c6fe0b3d4
Fixed regression preventing lift to work correctly
2012-10-30 10:45:55 +01:00
Alessandro Ranellucci
887634e1e2
Use G92 to apply Z offset. #486
2012-10-29 19:54:04 +01:00
Alessandro Ranellucci
709cbc1c15
Fixed regression causing support material generation to fail under threaded perls
2012-10-29 19:38:40 +01:00
Alessandro Ranellucci
df4dcf0534
Move by 30° instead of 45° when completing an external loop. #186
2012-10-29 11:21:41 +01:00
Alessandro Ranellucci
9b94a661d9
Fixed regression causing too much clipping at the endpoints of loops
2012-10-29 11:20:27 +01:00
Alessandro Ranellucci
e9ae62a9d1
New --min-skirt-length option. #269
2012-10-29 11:17:57 +01:00
Alessandro Ranellucci
c25e54a830
Expose perimeter/infill/support material extrusion widths in G-code comments
2012-10-29 00:31:25 +01:00
Alessandro Ranellucci
f2389682b6
Factor out some hard-coded settings
2012-10-29 00:23:33 +01:00
Alessandro Ranellucci
1ecadc10fb
Fixed regression causing one perimeter to be generated even when perimeters where set to 0. #759
2012-10-28 19:27:54 +01:00
Alessandro Ranellucci
8da4151c6d
Fix regression causing skirt to be printed at Z = 0 after a recent commit
2012-10-28 19:24:24 +01:00
Alessandro Ranellucci
c57e94c065
Experimental feature: make a little move inwards by 45° after finishing the external perimeter and before retracting. #186
2012-10-28 19:15:34 +01:00
Alessandro Ranellucci
ecd054a57c
Don't emit T0 at the beginning of the file, so that it's generated automatically just right before starting the print
2012-10-28 17:29:01 +01:00
Alessandro Ranellucci
935173047a
Allow [print_center_X] and [print_center_Y] syntax for all coordinates settings (including bed_center etc.) and [temperature_0], [temperature_1] etc. for all index-based settings
2012-10-28 17:23:35 +01:00
Alessandro Ranellucci
ccb49a8439
Do a slightly thinner interface layer at the top of support material structures by taking into account the diameter of bridge extrudates (nophead's idea)
2012-10-28 16:59:20 +01:00
Alessandro Ranellucci
b5bd216f5c
Do not combine infill for bottom layer
2012-10-28 14:23:47 +01:00
Alessandro Ranellucci
f35cdef2aa
Renamed ExtrusionPath->depth_layers to height
2012-10-28 14:22:51 +01:00
Alessandro Ranellucci
2796041a6c
Bugfix: --top-solid-layers was ignored. #769
2012-10-28 12:52:53 +01:00
Alessandro Ranellucci
deea02b444
Descriptive textual feedback for cooling settings
2012-10-28 12:43:41 +01:00
Alessandro Ranellucci
f9b6caaecb
Bugfix, last commit was incomplete
2012-10-28 12:22:30 +01:00
Alessandro Ranellucci
a0fe93e8cf
Bugfix: sometimes first layer extrusion width was not applied
2012-10-28 10:28:40 +01:00
Alessandro Ranellucci
49916b6178
Revert 2bcac88683 by setting the scale factor manually to 1. #720
2012-10-27 22:09:22 +02:00
Alessandro Ranellucci
d0bee4bf41
Fixed regression in Split. #766
2012-10-27 21:39:57 +02:00
Alessandro Ranellucci
bc9ff848dd
Removed unused 'propgrid' import group from Wx. #764
2012-10-27 21:21:18 +02:00
Alessandro Ranellucci
f9e20db156
Update t/dynamic.t
2012-10-27 21:20:32 +02:00
Alessandro Ranellucci
b0f24a2666
Bugfix: unnecessary tool changes were generated when using the same tool for subsequent parts
2012-10-25 18:49:59 +02:00
Alessandro Ranellucci
667d88603e
Reorder some options using the more compact layout
2012-10-25 12:37:02 +02:00
Alessandro Ranellucci
cee3864fc9
Independently set number of top/bottom solid layers. #676
2012-10-25 12:21:04 +02:00
Alessandro Ranellucci
bbd7765f40
Refactored the options group building to allow for more flexible layouts
2012-10-25 11:24:56 +02:00
Alessandro Ranellucci
31c2e50fc6
Bugfix: bed temperature wasn't being set after the first layer when first layer bed temperature was set to zero. #760
2012-10-24 22:57:19 +02:00
Alessandro Ranellucci
50f6909475
Don't apply slowdown factor to bridges. #640
2012-10-24 22:55:03 +02:00
Alessandro Ranellucci
392af5542b
Show object information when double-clicking it in the plater
2012-10-24 22:44:08 +02:00
Alessandro Ranellucci
304676b6aa
Use XML::SAX::ExpatXS if available
2012-10-24 20:36:32 +02:00
Alessandro Ranellucci
3c8ac435ad
Remember last used filament presets when using multiple extruders too
2012-10-24 20:24:11 +02:00
Alessandro Ranellucci
355031fe2f
Remove unnecessary retractions
2012-10-24 19:38:18 +02:00
Alessandro Ranellucci
44016b38c5
Distribute skirt loops across all extruders
2012-10-24 19:13:40 +02:00
Alessandro Ranellucci
f0d2b0e5ea
Avoid overlapping regions (thanks Mike Sheldrake!). #726
2012-10-24 16:46:40 +02:00
Alessandro Ranellucci
1c50c8a401
Merge branch 'dynamic-flow'
2012-10-24 16:19:13 +02:00
Alessandro Ranellucci
6beaf5e597
New faster algorithm for filling gaps, while we work on a new medial axis implementation
2012-10-24 16:17:09 +02:00
Alessandro Ranellucci
1445820673
External perimeter first on bottom layer when brim is enabled. #761
2012-10-24 12:04:44 +02:00
Alessandro Ranellucci
1627268fd4
Merge branch 'master' into avoid-crossing-perimeters
...
Conflicts:
lib/Slic3r/GCode.pm
2012-10-24 11:49:31 +02:00
Alessandro Ranellucci
19e77a28a1
Merge branch 'master' into dynamic-flow
2012-10-24 10:55:57 +02:00
Alessandro Ranellucci
28b56ae840
Force unfocusing of all input fields when saving a preset, otherwise the currently focused one might be ignored. #750 #624
2012-10-22 16:03:08 +02:00
Alessandro Ranellucci
c793a2657f
Replace Math::ConvexHull with Math::ConvexHull::MonotoneChain. #722
2012-10-22 15:29:54 +02:00
Alessandro Ranellucci
68c3a0dd61
Make arcs.t happy. #721
2012-10-22 14:08:27 +02:00
Alessandro Ranellucci
33b1970b95
Incomplete commit broke the plater on threaded perls
2012-10-22 14:02:58 +02:00
Alessandro Ranellucci
0990a9418c
Bugfix: honeycomb infill was overlapping too much with perimeters. #732
2012-10-22 13:38:37 +02:00
Alessandro Ranellucci
3c7785aaf3
Useless extra perimeters were generated sometimes. #444 #732
2012-10-22 13:21:11 +02:00
Alessandro Ranellucci
76f75db055
Always specify tool number in M104/M109 when printing with multiple extruders
2012-10-21 21:44:06 +02:00
Alessandro Ranellucci
4f1b56f004
Fix regression causing the plater to merge all materials into a single one, thus not producing multi-extrusion prints
2012-10-21 20:56:19 +02:00
Alessandro Ranellucci
f5f9574173
Merge pull request #722 from mesheldrake/remove-dups-before-hull
...
use remove_coinciding_points before convex_hull
2012-10-15 02:49:30 -07:00
Alessandro Ranellucci
149d9e737b
Merge pull request #721 from mesheldrake/parallel-degrees-limit
...
parallel_degrees_limit decreased, 3 to 0.1, #704
2012-10-15 02:48:16 -07:00
Alessandro Ranellucci
50161497f3
Merge pull request #720 from mesheldrake/increase-offset-scale
...
Increase scale factor for Clipper::offset
2012-10-15 02:47:16 -07:00
Alessandro Ranellucci
6b4f038d17
Update copies number when decreasing parts. #747
2012-10-15 10:59:54 +02:00
Alessandro Ranellucci
769134bb6f
Fixed regression causing skirt ignoring the first layer extrusion width override. #728
2012-10-15 10:57:15 +02:00
Alessandro Ranellucci
8ac367bfa7
If brim overlaps with skirt, make brim around skirt too instead of just ignoring skirt on first layer
2012-10-14 22:10:49 +02:00
Alessandro Ranellucci
b92642459f
Merge branch 'master' into dynamic-flow
...
Conflicts:
lib/Slic3r/Flow.pm
lib/Slic3r/Layer.pm
2012-10-04 15:23:19 +02:00
Alessandro Ranellucci
d1e0bcf113
Bugfix: tool numbers written in G-code were wrong
2012-10-01 18:22:35 +02:00
Alessandro Ranellucci
1a6eaeaa91
Bugfix: split wasn't working properly under threaded perls
2012-10-01 18:12:14 +02:00
Alessandro Ranellucci
2c400ee2b8
Removed useless warning
2012-10-01 16:49:02 +02:00
Alessandro Ranellucci
faaf6d90b8
Bump version number
2012-09-28 17:44:38 +02:00
Alessandro Ranellucci
6bb4c28b01
Release 0.9.3
2012-09-28 17:06:19 +02:00
Alessandro Ranellucci
86e3508402
Add menu item pointing to documentation
2012-09-28 16:58:03 +02:00
Alessandro Ranellucci
22b312395a
Fix SVG/DLP support material. #673
2012-09-28 16:32:53 +02:00
Alessandro Ranellucci
c68862582c
Fix fatal error on empty layers caused by recent large refactorings
2012-09-28 15:48:32 +02:00
Alessandro Ranellucci
ab7697ec1c
New option to force a solid layer every given number of layers. #617
2012-09-28 15:46:29 +02:00
Alessandro Ranellucci
f50b0040ef
Bugfix: the grow() method wasn't working properly, causing bad brim/support material interface. #639
2012-09-28 15:27:33 +02:00
Alessandro Ranellucci
9ee9b54c73
Output an error if user tries to use 100% density with a non-solid fill pattern. #691
2012-09-28 14:13:06 +02:00
Alessandro Ranellucci
a49b045ce4
Do not call srand for each layer, to get better randomization of starting points. #694
2012-09-28 14:01:59 +02:00
Mike Sheldrake
4b91496edd
use remove_coinciding_points before convex_hull
...
convex_hull returns polygons with sharp concaves sometimes when
duplicate points are present
2012-09-27 06:47:38 -07:00
Mike Sheldrake
5ee68aa916
$parallel_degrees_limit decreased, 3 to 0.1, #704
...
Geometry::lines_parallel() test used for collapsing adjacent colinear
lines was too loose in testing for colinearity, because of this constant
setting. Gradualy curving and high-res outer perimiters would
over-simplify into straight lines.
2012-09-27 06:14:54 -07:00
Mike Sheldrake
2bcac88683
Increase scale factor for Clipper::offset
...
A default scale of 1 was being calculated most of the time. That's too
low to avoid artifacts from offsetting concave curves. Setting scale to
a default of 100000 eliminates artifacts in the test cases in issues
#700 , #702 and #703 . There is a risk of large point proliferation with
this scale in combination with the JT_ROUND option, but in the four
places where that option is used, scale is already explicitly set to a
safer low value.
2012-09-27 05:50:54 -07:00
Alessandro Ranellucci
fd74577eae
Fix typo in previous commit
2012-09-24 21:00:26 +02:00
Alessandro Ranellucci
d8c192ae05
Fix fatal error caused by recent refactorings
2012-09-23 18:07:44 +02:00
Alessandro Ranellucci
1f4706f02f
[print_preset] and others were erroneously renamed to [print] etc. #675
2012-09-23 17:40:34 +02:00
Alessandro Ranellucci
77625894ff
New command to combine multiple STL files into a single multi-material AMF file
2012-09-23 14:48:58 +02:00
Alessandro Ranellucci
bbe0a45b58
Optimization: cache scaled flow width and spacing
2012-09-23 03:03:08 +02:00
Alessandro Ranellucci
ec0d3987db
Rename materials to regions
2012-09-23 02:52:31 +02:00
Alessandro Ranellucci
e696764af8
Assign extruders and flows to materials
2012-09-23 02:40:25 +02:00
Alessandro Ranellucci
e2ab340edb
Fix positioning and other things
2012-09-22 21:03:57 +02:00
Alessandro Ranellucci
d488afd243
More work (breaks centering and internal surfaces detection)
2012-09-22 19:38:25 +02:00
Alessandro Ranellucci
02356fd613
Large refactoring to allow processing multimaterial files
2012-09-22 19:04:36 +02:00
Alessandro Ranellucci
04be94023b
Refactoring: move the 'copies' property to each Print::Object
2012-09-22 16:19:24 +02:00
Alessandro Ranellucci
82ac4722d2
Refactoring, new size_3D function
2012-09-22 16:12:54 +02:00
Alessandro Ranellucci
b5672de3ca
Refactoring, new bounding_box_3D function
2012-09-22 16:10:24 +02:00
Alessandro Ranellucci
91e9f651b5
Bugfix: --avoid-crossing-perimeters was crashing when processing empty layers
2012-09-22 15:51:18 +02:00
Alessandro Ranellucci
35e449e891
Make new plater compatible with threaded perls
2012-09-21 17:45:54 +02:00
Alessandro Ranellucci
037be34b7b
Bugfix: removed fatal error when generating SVG support material in some circumstances. #673
2012-09-21 16:52:05 +02:00
Alessandro Ranellucci
c6c7dd12da
Silently ignore threads > 1 on non-threaded perls
2012-09-21 16:43:46 +02:00
Alessandro Ranellucci
27b71d8885
Little regressions after recent merge
2012-09-21 16:08:22 +02:00
Alessandro Ranellucci
392309a369
Little cleanup
2012-09-21 15:58:44 +02:00
Alessandro Ranellucci
e21fdf0b15
Little cleanup
2012-09-21 15:47:38 +02:00
Alessandro Ranellucci
2f1ae3f112
Restore non-manifold warnings
2012-09-21 15:46:40 +02:00
Alessandro Ranellucci
c95cd5ac38
Merge branch 'master' into avoid-crossing-perimeters
2012-09-21 15:36:45 +02:00
Alessandro Ranellucci
46cbdcdc4e
Merge branch 'master' into dynamic-flow
2012-09-21 15:36:33 +02:00
Alessandro Ranellucci
f638558167
Preserve position when splitting objects in plater
2012-09-21 15:35:32 +02:00
Alessandro Ranellucci
e40f32995f
Finish GUI decoupling
2012-09-21 15:04:33 +02:00
Alessandro Ranellucci
8382eeef0a
Revert "Patch for --gcode-arcs (kindly submitted by Paul Howes)"
...
This reverts commit f4260ae93d
2012-09-21 15:04:19 +02:00
Alessandro Ranellucci
f659dcf088
Patch for --gcode-arcs (kindly submitted by Paul Howes)
2012-09-21 15:04:19 +02:00
Alessandro Ranellucci
757515ba17
New [print_preset], [filament_preset] and [printer_preset] variables. #675
2012-09-21 15:04:18 +02:00
Alessandro Ranellucci
4fbb8ffb9d
Replace 'scale epsilon' with 'scaled_epsilon'
2012-09-21 15:04:18 +02:00
Alessandro Ranellucci
87912cb3b0
Bugfix: only_retract_when_crossing_perimeters was almost not working. #680
2012-09-21 15:04:18 +02:00
Alessandro Ranellucci
f314cedd8f
Bugfix: extrusion width setting for support material was only affecting the path spacing but not the actual flow. #666
2012-09-21 15:04:17 +02:00
Alessandro Ranellucci
d848e2d4c9
Warn the user when Slic3r is being run under 5.16
2012-09-21 15:04:17 +02:00
Alessandro Ranellucci
e89f64e9d3
More unfinished work
2012-09-21 15:04:17 +02:00
Alessandro Ranellucci
6adf98edaf
Fix regression causing SVG/DLP support material to crash the application. #668
2012-09-21 15:04:16 +02:00
Alessandro Ranellucci
37ae2e1e2d
Use support material extruder for brim. #653
2012-09-21 15:04:16 +02:00
Alessandro Ranellucci
3b38e392ad
Consider single walls as external perimeters. #661
2012-09-21 15:04:15 +02:00
Alessandro Ranellucci
47c5d410ea
Remove the initial retraction compensation. Not only it is not very good for multi-head setups, but it also caused wrong first layer Z when lift was enabled. #655
2012-09-21 15:04:15 +02:00
Alessandro Ranellucci
152c714b87
Bump version number
2012-09-21 15:04:13 +02:00
Alessandro Ranellucci
d7e801fd32
Releasing 0.9.2
2012-09-21 15:04:13 +02:00
Alessandro Ranellucci
202bfa91c8
Adjust M-codes for temperature handling for Teacup. #539
2012-09-21 15:04:12 +02:00
Alessandro Ranellucci
94a096f1d2
Support legacy config files not containing first_layer_height #631
2012-09-21 15:04:11 +02:00
Alessandro Ranellucci
1cedb00f20
Merge branch 'master' into dynamic-flow
...
Conflicts:
lib/Slic3r/ExPolygon.pm
2012-09-12 16:05:06 +02:00
Alessandro Ranellucci
cc8d8bd26f
Merge branch 'master' into avoid-crossing-perimeters
...
Conflicts:
README.markdown
lib/Slic3r/Config.pm
lib/Slic3r/GCode.pm
lib/Slic3r/Print.pm
slic3r.pl
2012-09-12 16:04:16 +02:00
Alessandro Ranellucci
2a51cad0c3
Revert "Patch for --gcode-arcs (kindly submitted by Paul Howes)"
...
This reverts commit f4260ae93d
2012-09-12 15:58:01 +02:00
Alessandro Ranellucci
f4260ae93d
Patch for --gcode-arcs (kindly submitted by Paul Howes)
2012-09-12 15:53:24 +02:00
Alessandro Ranellucci
7a5071f66c
New [print_preset], [filament_preset] and [printer_preset] variables. #675
2012-09-12 15:29:44 +02:00
Alessandro Ranellucci
e0d5f4e528
Replace 'scale epsilon' with 'scaled_epsilon'
2012-09-12 15:22:43 +02:00
Alessandro Ranellucci
9934f8957f
Bugfix: only_retract_when_crossing_perimeters was almost not working. #680
2012-09-12 15:20:37 +02:00
Alessandro Ranellucci
bb5f00cf0c
Bugfix: extrusion width setting for support material was only affecting the path spacing but not the actual flow. #666
2012-09-12 12:13:43 +02:00
Alessandro Ranellucci
36796645cb
Warn the user when Slic3r is being run under 5.16
2012-09-11 16:02:26 +02:00
Alessandro Ranellucci
628cc52338
Fix regression causing SVG/DLP support material to crash the application. #668
2012-09-06 11:28:24 +02:00
Alessandro Ranellucci
f41a6af343
Use support material extruder for brim. #653
2012-09-06 11:01:44 +02:00
Alessandro Ranellucci
1053947c19
Consider single walls as external perimeters. #661
2012-09-06 10:56:42 +02:00
Alessandro Ranellucci
e0a96c00b3
Remove the initial retraction compensation. Not only it is not very good for multi-head setups, but it also caused wrong first layer Z when lift was enabled. #655
2012-09-06 10:44:48 +02:00
Alessandro Ranellucci
8d7b781473
Bump version number
2012-08-31 00:12:13 +02:00
Alessandro Ranellucci
25f647a60c
Releasing 0.9.2
2012-08-30 23:15:42 +02:00
Alessandro Ranellucci
5017f17171
Adjust M-codes for temperature handling for Teacup. #539
2012-08-30 23:13:28 +02:00
Alessandro Ranellucci
b37af86bef
Support legacy config files not containing first_layer_height #631
2012-08-30 23:04:56 +02:00
Alessandro Ranellucci
191de5d078
Unfinished work for decoupling GUI from the Print object (goal = more speed for manipulation, less memory usage)
2012-08-29 19:37:27 +02:00
Alessandro Ranellucci
f29d455319
Refactor the AMF parser so that it popolates a Model object directly. Also read constellations
2012-08-29 18:23:34 +02:00
Alessandro Ranellucci
23f6842bd4
Export plates as AMF constellations
2012-08-29 17:12:32 +02:00
Alessandro Ranellucci
f90520ed06
Refactoring: new Slic3r::Model class to represent files
2012-08-29 17:12:32 +02:00
Alessandro Ranellucci
9bd1b0f6ba
Revert "Refactoring: initialize all layers at once and avoid duplication of slicing height math". #637
...
This reverts commit 08270022dd
2012-08-26 17:47:00 +02:00
Alessandro Ranellucci
08270022dd
Refactoring: initialize all layers at once and avoid duplication of slicing height math
2012-08-25 20:40:44 +02:00
Alessandro Ranellucci
a1a4d97f9f
Remove useless subroutines
2012-08-25 20:14:52 +02:00
Alessandro Ranellucci
a1ac866b84
Refactoring: turn x_length and y_length in size
2012-08-25 20:14:01 +02:00
Alessandro Ranellucci
896641cb7e
Fixed regression causing some bridges not to be detected correctly. #629
2012-08-25 20:04:29 +02:00
Alessandro Ranellucci
fe6c8fabdb
Make Josef Prusa and Petr Ledvinka happy while we figure out how to handle localized Windows file paths
2012-08-25 19:06:14 +02:00
Alessandro Ranellucci
873ea93832
Fix missing module inclusion preventing the recently introduced option from working
2012-08-25 17:18:12 +02:00
Alessandro Ranellucci
0c22250740
New option to disable retraction when moving between infill paths inside the same island. #29
2012-08-25 16:30:11 +02:00
Alessandro Ranellucci
af1b64a086
Added unit testing to prevent regression about disconnected infill paths
2012-08-25 14:59:34 +02:00
Alessandro Ranellucci
d061534b83
Merge branch 'master' into avoid-crossing-perimeters
...
Conflicts:
README.markdown
lib/Slic3r/ExPolygon.pm
slic3r.pl
2012-08-25 14:26:32 +02:00
Alessandro Ranellucci
0aa224ffad
Dynamic extrusion width for better gap filling
2012-08-25 14:23:46 +02:00
Alessandro Ranellucci
65b11fa850
Minor refactoring for better readability of perimeter generation logic
2012-08-24 21:58:51 +02:00
Alessandro Ranellucci
92518d28fc
New option to configure the threshold for enforcing solid infill. #224
2012-08-24 19:38:36 +02:00
Alessandro Ranellucci
ba58e0733f
Avoid backwards moves when doing honeycomb infill. #492
2012-08-24 19:19:45 +02:00
Alessandro Ranellucci
5281b101f9
Some infill paths were still disconnected, causing unnecessary retractions
2012-08-24 18:59:23 +02:00
Alessandro Ranellucci
56a118986f
External motion was crossing still too much
2012-08-23 21:19:10 +02:00
Alessandro Ranellucci
c98e9515ed
Better implementation of the external motion planner
2012-08-23 21:10:04 +02:00
Alessandro Ranellucci
27090f83bd
Make the motionplanner work again after recent changes to approximation
2012-08-23 17:02:50 +02:00
Alessandro Ranellucci
ee41345ab0
Remove useless Point->id method
2012-08-23 15:46:55 +02:00
Alessandro Ranellucci
0eadc5adba
Manual rebase of the avoid_crossing_perimeters feature
2012-08-23 15:42:58 +02:00
Alessandro Ranellucci
d278998f11
Accept newline as separator for post-processing scripts in GUI. #615
2012-08-22 21:27:49 +02:00
Alessandro Ranellucci
b35c41c1a3
Bugfix: retraction was still not working correctly at tool change
2012-08-22 20:31:03 +02:00
Alessandro Ranellucci
edfdf236da
Fix for the recent commit about the new retraction settings
2012-08-22 19:47:59 +02:00
Alessandro Ranellucci
4bddb66513
Always emit T0 at the beginning of a multi-extruder print
2012-08-22 19:20:34 +02:00
Alessandro Ranellucci
9e682924c7
New separate options for retraction length to be used when switching tools
2012-08-22 19:11:45 +02:00
Alessandro Ranellucci
075213c731
Refactoring: make 'retracted' an attribute of the Extruder object
2012-08-22 18:57:03 +02:00
Alessandro Ranellucci
97c3756034
Don't force automatic unretraction after tool change
2012-08-22 18:06:50 +02:00
Alessandro Ranellucci
3c2464abf9
Bugfix: crazy temperatures were written when using sequential printing. #625
2012-08-22 17:58:38 +02:00
Alessandro Ranellucci
26e033a30c
Bugfix: brim was positioned incorrectly if no skirt was enabled. #627
2012-08-19 20:30:17 +02:00
Henrik Brix Andersen
d6b06e08bc
Bump version number
2012-08-19 09:49:43 +02:00
Nicolas Dandrimont
a147530d2a
Explicitly avoid passing arguments to remove when called from the event handler
...
Wx passes some objects to the callbacks, and we want to ignore those.
2012-08-11 16:05:17 +02:00
Nicolas Dandrimont
7b0d4cb4e1
Revert "Dereference the Wx object id when removing an object in the plater."
...
This reverts commit 4979029cd2
2012-08-11 16:00:41 +02:00
Nicolas Dandrimont
4979029cd2
Dereference the Wx object id when removing an object in the plater.
2012-08-11 15:49:06 +02:00
Alessandro Ranellucci
0833b4e021
Releasing 0.9.1
2012-08-10 16:14:35 +02:00
Alessandro Ranellucci
624e16b7e2
Unexpected results splitting objects with threaded perls. #610
2012-08-10 16:05:16 +02:00
Henrik Brix Andersen
2576e3b00a
Remove XXX debug output
2012-08-09 23:37:15 +02:00
Alessandro Ranellucci
8289692160
Handle configuration files saved while there was no extruder_offset control for the first extruder
2012-08-09 19:57:49 +02:00
Alessandro Ranellucci
d02012e4a3
Accept multiple --load arguments for GUI too
2012-08-09 00:59:41 +02:00
Alessandro Ranellucci
db8bb8c3d8
Revert "Hide extruder offset settings for the primary extruder"
...
This reverts commit 713d87b4c6
2012-08-09 00:51:53 +02:00
Alessandro Ranellucci
2bf219a637
Bugfix: random failure to load presets. #600
2012-08-09 00:41:03 +02:00
Alessandro Ranellucci
927b7ce937
Bugfix: skirt height and other options shouldn't be limited to 100. #597
2012-08-08 23:51:40 +02:00
Alessandro Ranellucci
88cbae0d48
Bugfix: saving a printer preset with less extruders than it had resulted in the same number of extruders as before
2012-08-08 22:52:26 +02:00
Alessandro Ranellucci
713d87b4c6
Hide extruder offset settings for the primary extruder
2012-08-08 22:14:05 +02:00
Alessandro Ranellucci
9ca21c835c
Merge branch 'per-extruder-retraction-settings'
...
Conflicts:
lib/Slic3r/Config.pm
lib/Slic3r/GUI/Tab.pm
2012-08-08 22:06:47 +02:00
Alessandro Ranellucci
55b3b4f0c5
Bump version number
2012-08-08 22:04:06 +02:00
Henrik Brix Andersen
e2b2e369f8
Disable using ENTER key for accessing "Export G-code..." button.
2012-08-08 21:45:17 +02:00
Alessandro Ranellucci
4fcecf5ef6
Bugfix: when an external config was selected in any section, exported settings didn't reflect other sections properly
2012-08-08 19:36:34 +02:00
Alessandro Ranellucci
2f2bc8210a
Allow exporting to .g files too
2012-08-08 19:04:36 +02:00
Alessandro Ranellucci
3888727b96
Bugfix: legacy config files with empty temperature and/or first_layer_temperature caused crash
2012-08-08 16:25:13 +02:00
Alessandro Ranellucci
b048f51edd
Incomplete label for support material extruder option. #593
2012-08-08 15:21:02 +02:00
Alessandro Ranellucci
d4d305db3b
Releasing 0.9.0
2012-08-08 12:29:15 +02:00
Henrik Brix Andersen
0f327ef912
Add missing use File::Spec
2012-08-07 23:37:16 +02:00
Alessandro Ranellucci
c7858912d8
Bugfix: some paths were not considered when generating brim
2012-08-07 22:04:58 +02:00
Alessandro Ranellucci
866b09f3f9
New --extruder-offset option
2012-08-07 21:39:45 +02:00
Alessandro Ranellucci
a2c28fd6da
Move retraction settings to a temporary page until we merge the per-extruder-retraction-settings branch
2012-08-07 21:11:58 +02:00
Alessandro Ranellucci
cf01c142de
Make retraction configurable for each extruder
2012-08-07 21:08:56 +02:00
Henrik Brix Andersen
640c07a233
Revert 4099c3a8cf
...
Presenting detailed statistics about a given slice needs rethinking, as this solution will not scale.
2012-08-07 21:00:03 +02:00
Alessandro Ranellucci
63e77fcfd8
Refactor extruder settings
2012-08-07 20:50:54 +02:00
Alessandro Ranellucci
106c8fe46f
Minor reordering of infill options in GUI; also hide the entire staticbox if threads are not available
2012-08-07 20:22:26 +02:00
Alessandro Ranellucci
2548d5b993
Expose all multi-extruder settings to the GUI
2012-08-07 20:14:28 +02:00
Alessandro Ranellucci
793301d319
Allow to select multiple filaments in GUI when multiple extruders are configured
2012-08-07 18:44:47 +02:00
Alessandro Ranellucci
b7d8444ac8
Take support material into account when generating brim. #490 #501 #567
2012-08-06 20:54:49 +02:00
Alessandro Ranellucci
9bfa4118a1
Bugfix: brim and skirt collision was not precisely detected when they had similar offsets. #548
2012-08-06 20:27:10 +02:00
Alessandro Ranellucci
2616c24ffc
Bugfix: plater wasn't initialized with last settings. #573
2012-08-06 19:19:22 +02:00
QuantumConcepts
6bcbc743dd
Fixed #586 .
2012-08-06 08:23:00 -04:00
Alessandro Ranellucci
a8e9b6926a
Bugfix: each tab was loading too much from external config files
2012-08-06 13:03:44 +02:00
Henrik Brix Andersen
49b048c61d
Include Wx version number in debug output
2012-08-04 22:19:42 +02:00
Henrik Brix Andersen
b1805ed7f3
Align controls and their associated labels vertically centered.
2012-08-02 23:44:42 +02:00
Henrik Brix Andersen
5518ac9fa6
Add small border on non-wxMAC platforms. Needs testing with wxWidgets 2.9.x on wxMSW + wxGTK.
2012-08-02 23:19:04 +02:00
Henrik Brix Andersen
c1e2bc5bd7
Make the wizard a tiny bit wider to fit the gcode_flavor drop-down under OS X.
2012-08-02 23:08:40 +02:00
Henrik Brix Andersen
ed89038f0b
Add work-around for "Gtk-WARNING **: gtk_widget_size_allocate(): attempt to allocate widget with width -5 and height 17". #558
2012-08-02 23:07:42 +02:00
Henrik Brix Andersen
794a090892
Pass explicit tool IDs to ::EnableTool()
2012-08-02 21:49:26 +02:00
Henrik Brix Andersen
69fa308f55
Allocate wxWidget identifiers dynamically to avoid potential conflics.
2012-08-02 21:11:36 +02:00
Henrik Brix Andersen
0e620f3ad2
Make --output accept directories. #535
2012-08-01 17:12:16 +02:00
Henrik Brix Andersen
d1b8f37dda
Call print->config before print->expanded_output_filepath. #573
2012-08-01 16:06:03 +02:00
Henrik Brix Andersen
65d6eb551a
Try harder to attract user attention on wxMAC. #575
2012-08-01 13:59:43 +02:00
Henrik Brix Andersen
83fccf0875
Fix auto-arrange of objects
2012-07-30 19:30:41 +02:00
Henrik Brix Andersen
0aae15e2a8
Persist last skein directory and last config directory used across application restarts.
2012-07-30 12:08:28 +02:00
Alessandro Ranellucci
0e39a89d01
Fixed regression preventing split from working. #395
2012-07-30 10:00:25 +02:00
Sam Wong
4099c3a8cf
#568 : Show filament needed statistics in the GUI message box.
2012-07-30 01:24:51 +08:00
Alessandro Ranellucci
4c33eabc6e
Slicing from plater was still using the default options
2012-07-29 17:02:46 +02:00
Alessandro Ranellucci
9933132ae6
Bugfix: recent refactoring broke slicing from plater on multi-threaded perls
2012-07-29 15:51:26 +02:00
Alessandro Ranellucci
92754d7cd4
Fix multi-extruder options in GUI
2012-07-28 11:53:10 +02:00
Alessandro Ranellucci
87934a972c
Port recent global changes to the wizard
2012-07-28 11:34:12 +02:00
Alessandro Ranellucci
c763f5fc81
Bugfix: fatal error with thin loops after recent refactoring. #562
2012-07-28 11:06:27 +02:00
Henrik Brix Andersen
57b134cc9c
Handle recursive ratio_over options correctly.
2012-07-27 22:56:35 +02:00
Henrik Brix Andersen
d68ab84faa
Fix quick slicing
2012-07-27 22:03:48 +02:00
Alessandro Ranellucci
7e34244b05
Refactored configuration handling.
...
Slic3r::Config is now an object. Multiple partial config objects are used throughout the codebase as local repositories, then merged and serialized when necessary.
2012-07-27 21:16:11 +02:00
Henrik Brix Andersen
f0579e59bd
Include timestamp in .ini files
2012-07-27 14:33:14 +02:00
Henrik Brix Andersen
9f719d42bc
Include preset name in confirmation dialog
2012-07-27 14:11:04 +02:00
Henrik Brix Andersen
9e1308c03f
Ask for confirmation when deselecting a dirty preset.
2012-07-27 13:57:58 +02:00
Henrik Brix Andersen
848784ad95
Clear dirty when deleting preset.
2012-07-27 13:56:52 +02:00
Henrik Brix Andersen
40f1176346
Be careful not to change the current selection when working around http://trac.wxwidgets.org/ticket/13769
2012-07-27 13:54:45 +02:00
Henrik Brix Andersen
1cc0a79188
Allow the list and buttons to expand upon window resize
2012-07-26 16:50:57 +02:00
Henrik Brix Andersen
7b06255dca
Center preset buttons
2012-07-26 16:48:28 +02:00
Henrik Brix Andersen
63e8299f14
Eliminate single-item wxSizer.
2012-07-26 16:41:22 +02:00
Henrik Brix Andersen
85603c1981
Highlight the dragged object.
2012-07-25 10:06:45 +02:00
Henrik Brix Andersen
affaee415b
Reset mouse cursor on button up event.
2012-07-25 00:51:41 +02:00
Henrik Brix Andersen
5502537065
Change cursor when hoovering over a movable object.
2012-07-25 00:15:32 +02:00
Henrik Brix Andersen
e02ee17247
Respect multiline option flag. #559
2012-07-24 20:16:34 +02:00
Henrik Brix Andersen
0e6d6a9695
Force sane TAB key order on buttons in GridSizer.
2012-07-24 18:21:02 +02:00
Alessandro Ranellucci
1d364d7823
Refactor OptionsGroup to decouple it from the config repository, add ConfigOptionsGroup
2012-07-24 15:33:11 +02:00
Henrik Brix Andersen
09a222f8b2
Reshuffle code a bit to preserve TAB key order between toolbar and listctrl.
2012-07-24 14:42:38 +02:00
Henrik Brix Andersen
44f3b7d2b5
Allow TAB key navigation of controls.
2012-07-24 14:28:21 +02:00
Henrik Brix Andersen
0b0e531661
Use more generic EVT_KEY_DOWN().
2012-07-24 14:17:10 +02:00
Henrik Brix Andersen
4bee713579
Add menuitems with keyboard shortcuts to quickly navigate between tabs.
2012-07-24 12:59:02 +02:00
Henrik Brix Andersen
4dc41d2ca3
Intercept TAB key events in the wxTreeCtrl and generate a wxNavigationKeyEvent.
2012-07-24 12:42:58 +02:00
Henrik Brix Andersen
69e075df82
Hidden Sizer items does not take up space, simply show/hide pages instead of removing/adding them.
2012-07-24 12:41:51 +02:00
Henrik Brix Andersen
642bb336eb
Add the page before showing it.
2012-07-24 00:34:57 +02:00
Henrik Brix Andersen
37667d87ce
Use Wx::Sizer::Detach() instead of Wx::Sizer::Remove()
2012-07-24 00:34:07 +02:00
Alessandro Ranellucci
ea604384dd
Typo
2012-07-23 17:56:20 +02:00
Alessandro Ranellucci
ba475cae45
Fixed fatal error introduced after recent refactoring
2012-07-23 17:52:02 +02:00
Henrik Brix Andersen
6f6fb22657
Add menu item hints
2012-07-23 16:31:16 +02:00
Henrik Brix Andersen
ab9ffe9c19
Expose --external-perimeter-speed in the GUI. #556
2012-07-23 09:43:59 +02:00
Alessandro Ranellucci
67b415a2b3
Remove almost duplicated logic for small infill regions detection
2012-07-22 21:06:19 +02:00
Alessandro Ranellucci
144a704e3b
Remove all id() and ordered_id() methods
2012-07-22 21:00:02 +02:00
Alessandro Ranellucci
1d04e15b63
Refactor/clean up. Merge remove_small_surfaces() into prepare_fill_surfaces(), rename infill_every_layers() to combine_infill(), remove $layer->fill_boundaries, initialize layer properties explicitely for clarity.
2012-07-22 21:00:02 +02:00
Henrik Brix Andersen
a5d683a9b9
Retire unused class variable 'fields'.
2012-07-22 15:23:42 +02:00
Henrik Brix Andersen
9486a629b3
Fix speling.
2012-07-22 15:06:56 +02:00
Alessandro Ranellucci
3edf42e98e
Little workflow simplification
2012-07-21 15:53:38 +02:00
Alessandro Ranellucci
c7bc9bed46
Workaround for a perl 5.10 bug about leaked scalars. #503
2012-07-21 14:45:45 +02:00
Alessandro Ranellucci
f899deb6b6
Prevent internal infill at all when fill density is set to zero. #545
2012-07-21 14:41:21 +02:00
Alessandro Ranellucci
1fdbd2c0e1
Suggest repair in non-manifold warning
2012-07-21 12:07:02 +02:00
Alessandro Ranellucci
bce2663ed8
Restore thin walls and thin fills after last commit
2012-07-20 15:02:25 +02:00
Alessandro Ranellucci
e71472e5d7
Remove debugging statements
2012-07-20 14:41:27 +02:00
Alessandro Ranellucci
1697cb24a6
Memory optimization and code cleanup. Don't keep deserialized paths
2012-07-20 14:39:56 +02:00
Henrik Brix Andersen
52fb02f29d
Turn nozzle count printf into debugf statement
2012-07-19 23:31:47 +02:00
Henrik Brix Andersen
35e6420ff5
Make the configuration wizard work on the first extruder.
2012-07-19 22:56:38 +02:00
Alessandro Ranellucci
30a2213fd9
Some multi-extruder options in GUI
2012-07-18 20:44:36 +02:00
Henrik Brix Andersen
9137a6b41e
Queue a repaint when changing options page, fixes repaint issue on wxMSW.
2012-07-18 19:19:07 +02:00
Alessandro Ranellucci
b861560c71
Fix tooltips about extrusion widths
2012-07-18 18:16:27 +02:00
Alessandro Ranellucci
2495a77c0f
Add to GUI the setting for support material extrusion width. Also, populate %Groups with new options
2012-07-18 18:15:18 +02:00
Alessandro Ranellucci
b209eab712
Bugfix: the delete button was deleting the wrong preset
2012-07-18 16:17:23 +02:00
Alessandro Ranellucci
f173096a6c
Merge branch 'new-gui'
...
Conflicts:
lib/Slic3r.pm
lib/Slic3r/Config.pm
lib/Slic3r/GUI/OptionsGroup.pm
lib/Slic3r/GUI/SkeinPanel.pm
lib/Slic3r/Print.pm
2012-07-18 15:48:04 +02:00
Alessandro Ranellucci
2d17a94a38
Prevent the left treectrl to grow if preset names are too long
2012-07-18 12:00:19 +02:00
Alessandro Ranellucci
42034ecb40
Autosize the main frame to workaround inconsistencies among wxGTK setups
2012-07-18 11:55:26 +02:00
Henrik Brix Andersen
fd88c164d2
Move Repeat Last Quick Slice below other Quick Slice items since it works for both.
2012-07-17 23:54:30 +02:00
Henrik Brix Andersen
a8d5ee3a74
Only enable Repeat Last Quick Slice menu item after the first quick slice.
2012-07-17 23:53:16 +02:00
Henrik Brix Andersen
c25a31ef98
Avoid SVG slicing interfering with repeating last quick slice.
2012-07-17 23:51:57 +02:00
Henrik Brix Andersen
bd16366d62
Default to "No" when prompting about discarding unsaved changes.
2012-07-17 23:24:21 +02:00
Henrik Brix Andersen
82cfc7c3d6
Check for unsaved presets before interactively loading an existing config file.
2012-07-17 23:16:58 +02:00
Henrik Brix Andersen
de47f5fe72
Use default desktop notification timeout.
2012-07-17 15:38:53 +02:00
Ryan Voots
19f4036d8a
Time here is in milliseconds, setting it to 1500 to make it stay for at least 1.5 seconds.
2012-07-16 19:04:25 -04:00
Henrik Brix Andersen
3690b0798e
Use Net::DBus instead of Gtk2::Notify due to less dependencies; recommended by @beanz.
2012-07-16 23:43:09 +02:00
Henrik Brix Andersen
095607a166
Remove excessive line breaks
2012-07-16 23:09:55 +02:00
Henrik Brix Andersen
99845955b3
Add support for libnotify notifications.
2012-07-16 22:37:31 +02:00
Henrik Brix Andersen
5d2fd17715
Use constants for menu item IDs.
2012-07-16 20:57:10 +02:00
Henrik Brix Andersen
e80d2813ed
Add keyboard shortcut for SVG slicing.
2012-07-16 19:23:51 +02:00
Henrik Brix Andersen
225414724c
Add keyboard accelerators to menus.
2012-07-16 19:13:35 +02:00
Henrik Brix Andersen
a6da019fc6
Adhere to various human interface guidelines.
2012-07-16 18:34:44 +02:00
Henrik Brix Andersen
fda21bd6f2
Only set $last_skein_dir from Plater, not $last_skein_file, to avoid interfering with Quick Slice.
2012-07-16 00:28:15 +02:00
Henrik Brix Andersen
b24e0370dd
Remove unused argument.
2012-07-15 23:59:50 +02:00
Henrik Brix Andersen
da7a668c94
Remove confirmation dialog on plate slicing done, request user attention instead. #537
2012-07-15 23:57:31 +02:00
Henrik Brix Andersen
a2a35f47f6
Convert Slic3r::GUI::notify() from class method to instance method.
2012-07-15 23:36:18 +02:00
Henrik Brix Andersen
9f3031a069
Remove Quick Slice button, move update text to statusbar.
2012-07-15 23:06:07 +02:00
Henrik Brix Andersen
102aea4531
Sync message dialog title with SkeinPanel.pm changes.
2012-07-15 22:53:32 +02:00
Henrik Brix Andersen
c35b57fb0b
Add spacer for correctly aligning top text under wxGTK.
2012-07-15 22:44:52 +02:00
Henrik Brix Andersen
e01b20ec8e
Add shortcuts keys for often used menu items.
2012-07-15 22:38:58 +02:00
Henrik Brix Andersen
5ef495a601
Improve repeated quick slice menu item text
2012-07-15 22:28:05 +02:00
Henrik Brix Andersen
314772b314
Improve message dialog texts a bit.
2012-07-15 22:25:04 +02:00
Henrik Brix Andersen
8042d5d701
Add borders to toolbar and list view.
2012-07-15 22:14:34 +02:00
Henrik Brix Andersen
0ab7e7ad7f
Show icons above text in toolbar.
2012-07-15 20:11:49 +02:00
Henrik Brix Andersen
bd77c33919
Add sunken border to tree controls.
2012-07-15 20:05:57 +02:00
Alessandro Ranellucci
1c6789e042
Remove duplicate_mode from options list
2012-07-15 19:36:56 +02:00
Alessandro Ranellucci
23fd8de1f5
Warn user if supplied preset name is not valid
2012-07-15 18:55:01 +02:00
Alessandro Ranellucci
b37a77ee63
Apply command line options to GUI
2012-07-15 18:37:00 +02:00
Alessandro Ranellucci
9210c708fc
Compatibility with --load and new GUI
2012-07-15 17:55:58 +02:00
Henrik Brix Andersen
e228b834e2
Retire the 'important' flag for options now that we have a configuration wizard.
2012-07-15 16:37:59 +02:00
Alessandro Ranellucci
606b9e49a7
Set first layer extrusion width to 200% by default
2012-07-15 15:53:08 +02:00
Alessandro Ranellucci
0aa3cc230f
Merge branch 'new-flow'
2012-07-14 21:40:57 +02:00
Henrik Brix Andersen
4a94c64f7d
Silence warning by importing Wx::Print before Wx::Html
2012-07-14 11:58:58 +02:00
Henrik Brix Andersen
57316a4ffa
Add custom about dialog.
2012-07-13 23:46:39 +02:00
Alessandro Ranellucci
e703e78504
A typo caused no newline after Tn. #530
2012-07-11 21:48:30 +02:00
Henrik Brix Andersen
500e44f8ea
Reposition of Slic3r::GUI::ProgressStatusBar fields are only needed in ::OnSize()
2012-07-11 16:55:47 +02:00
Henrik Brix Andersen
5e5dc02016
Add menu item shortcut for http://slic3r.org/
2012-07-11 16:31:17 +02:00
Henrik Brix Andersen
772ee033e0
Remove dead code.
2012-07-10 23:17:03 +02:00
Henrik Brix Andersen
025c3a1b07
Fix statusbar cancel button size on wxGTK. #431
2012-07-10 23:09:11 +02:00
Alessandro Ranellucci
079f6072a6
Use M109 P1 for Teacup
2012-07-10 19:31:09 +02:00
Henrik Brix Andersen
c144afe52b
Allow specifying --first-layer-height without leading zero. #518
2012-07-08 23:02:40 +02:00
Henrik Brix Andersen
37a4967883
Remove dead code.
2012-07-08 22:43:52 +02:00
Henrik Brix Andersen
023e7254c7
Make reports of time spent on slicing more user-friendly.
2012-07-08 22:16:46 +02:00
Henrik Brix Andersen
cd7ea418e2
Fix background logo on wxMSW.
...
Wx::StaticText + Wx::StaticBitmap does not support transparent backgrounds on wxMSW; fixed by using a custom paint routine instead.
2012-07-08 19:41:13 +02:00
Henrik Brix Andersen
0266729635
Merge branch 'master' into new-flow
2012-07-06 22:10:47 +02:00
Henrik Brix Andersen
9f4444a7d4
Add missing sprintf spotted by olasd
...
Fixes 3c00573805
2012-07-06 22:09:17 +02:00
Alessandro Ranellucci
4f6934bab8
Merge branch 'master' into new-flow
2012-07-06 20:06:09 +02:00
Alessandro Ranellucci
3c00573805
Reset E and compensate retraction after changing extruder
2012-07-06 19:57:58 +02:00
Alessandro Ranellucci
96574e601f
Infill flow wasn't adjusted for non-solid surfaces
2012-07-05 10:34:02 +02:00
Alessandro Ranellucci
7656167a0a
Infill flow wasn't adjusted for non-solid surfaces
2012-07-05 10:32:29 +02:00
Alessandro Ranellucci
3714fbe0f9
Fixed regression causing random extrudates outside the object perimeter
2012-07-04 10:35:42 +02:00
Alessandro Ranellucci
e4294cffce
Fixed regression causing random extrudates outside the object perimeter
2012-07-04 10:35:03 +02:00
Alessandro Ranellucci
9e77e6e8b6
Removed comment about the shortest path search for honeycomb not being useful: it is. #512
2012-07-04 10:02:45 +02:00
Alessandro Ranellucci
77123ada7c
New spacing math. Speed optimizations
2012-07-04 09:33:33 +02:00
Alessandro Ranellucci
dd37867324
Bugfix: wrong spacing was calculated
2012-07-04 09:33:33 +02:00
Henrik Brix Andersen
0982203f76
Fix configuration wizard background under wxGTK
2012-07-04 00:38:23 +02:00
Henrik Brix Andersen
a5c772a488
Add semi-transparent Slic3r icon as backdrop for the configuration wizard
2012-07-04 00:03:05 +02:00
Alessandro Ranellucci
566a0456ca
Fixed regression causing objects to be 0.1mm larger. #495 #507
2012-07-03 20:34:19 +02:00
Alessandro Ranellucci
5a8c4bf1bf
Move Load Config... and Export Config... to the File menu
2012-07-03 19:16:45 +02:00
Henrik Brix Andersen
3b873ab493
Merge branch 'wizard' into new-gui
2012-07-03 18:25:32 +02:00
Henrik Brix Andersen
3fa58cf85b
Add a friendly index
2012-07-03 17:21:32 +02:00
Henrik Brix Andersen
92ec70c860
Use wxDefaultPosition and wxDefaultSize to improve readability
2012-07-03 01:20:30 +02:00
Henrik Brix Andersen
e8a20eed6a
Use wxDefaultSize instead of [-1, -1]
2012-07-03 00:42:06 +02:00
Mark Hindess
35ecd65e77
Implement nearest point index and split at index to avoid search for point.
2012-07-02 20:26:56 +01:00
Mark Hindess
35fda7de23
Revert "split_at_first_point needn't call deserialize as split_at calls it."
...
This reverts commit a6d8d6473c
2012-07-02 16:57:29 +01:00
Mark Hindess
60ca76ff05
Oops. Somehow I missed this when doing interactive add.
2012-07-01 22:35:52 +00:00
Mark Hindess
ca78bbd88a
Use Slic3r::Geometry polyline_lines rather than duplicate implementation.
...
If it is good enough for polygons, it should be good enough for polylines.
2012-07-01 23:15:17 +01:00
Mark Hindess
b11778a85f
polygon_lines returns array of Slic3r::Line objects so bless is redundant.
2012-07-01 23:14:04 +01:00
Mark Hindess
a6d8d6473c
split_at_first_point needn't call deserialize as split_at calls it.
2012-07-01 22:52:13 +01:00
Henrik Brix Andersen
cd7661aa2a
Use proper ellipsis for all GUI '...' strings
2012-07-01 23:29:56 +02:00
Henrik Brix Andersen
a4219ba352
Sort imported events alphabetically
2012-07-01 19:35:48 +02:00
Henrik Brix Andersen
7746040af5
Clean up Wx imports
2012-07-01 19:24:06 +02:00
Alessandro Ranellucci
641c2a241b
Write Slic3r version in config files
2012-07-01 18:53:01 +02:00
Alessandro Ranellucci
c4b9a6cf61
Bugfix: flow wasn't adjusted for perimeters when a custom perimeters extrusion width was applied
2012-07-01 18:13:48 +02:00
Mark Hindess
07f2dab5f6
Fix perimeters_* options to be singular to be consistent.
2012-06-30 23:18:15 +01:00
Henrik Brix Andersen
bfe7108cea
Provide instructions for loading an existing configuration instead of using the wizard
2012-07-01 00:17:48 +02:00
Henrik Brix Andersen
8f0aab3520
Restore old configuration if configuration wizrd is cancelled
2012-07-01 00:10:48 +02:00
Henrik Brix Andersen
bb193c659c
Start configuration wizard from sane default settings
2012-06-30 23:56:11 +02:00
Henrik Brix Andersen
e656c30d4f
Clean up imports
2012-06-30 23:30:52 +02:00
Henrik Brix Andersen
757da9d39d
Clean up imports
2012-06-30 23:28:07 +02:00
Henrik Brix Andersen
d90e82faa3
Check for unsaved changes before running configuration wizard
2012-06-30 23:00:05 +02:00
Henrik Brix Andersen
df658eb636
Rename SkeinPanel::on_close() to make it more generice
2012-06-30 22:57:30 +02:00
Henrik Brix Andersen
a0f8078ee1
Warn on dirty default presets as well
2012-06-30 22:34:13 +02:00
Alessandro Ranellucci
cbb111ee64
Fix for incomplete commit causing thin gaps to throw an error
2012-06-30 17:23:55 +02:00
Alessandro Ranellucci
b9008a99f9
Fill the gaps while doing normal infill to avoid extra travel
2012-06-30 16:33:01 +02:00
Alessandro Ranellucci
5eb1982081
Bugfix: brim was extruded multiple times when sequential printing was enabled
2012-06-30 16:14:45 +02:00
Alessandro Ranellucci
a7668e0933
Revert "Reduce memory usage during gcode output by discarding processed layers."
...
This reverts commit 4d1551c305
2012-06-30 16:12:06 +02:00
Alessandro Ranellucci
d5c9b74377
Allow scaling factor to be at least 2540 to allow the conversion of inch models
2012-06-29 20:46:51 +02:00
Mark Hindess
b4a21bea40
Fix for #499 .
2012-06-29 17:02:37 +01:00
Mark Hindess
4d1551c305
Reduce memory usage during gcode output by discarding processed layers.
...
As each layer is processed, it increases in size by a factor of two
or three so by the end the layer list gets quite big. So this removes
the list entry after it's been processed.
2012-06-29 12:33:30 +01:00
Henrik Brix Andersen
4f179a5197
Explicitly set top level window (to ensure the wizard is not assumed to be the top level window)
2012-06-28 23:20:10 +02:00
Mark Hindess
2e1649e6b5
Comment out code that builds @vertices_facets data structure.
...
Saves memory and speeds up reading large models.
2012-06-28 19:58:21 +01:00
Alessandro Ranellucci
fb96cdec76
Command line options to assign perimeters and infill to different extruders
2012-06-28 16:48:56 +02:00
Alessandro Ranellucci
80501d5b3c
New option to customize support material extrusion width
2012-06-28 16:33:07 +02:00
Alessandro Ranellucci
f9f2361acb
Allow setting different temperatures and first layer temperatures for each extruder. Also make support material extruder selection compatible with the new architecture
2012-06-28 16:22:11 +02:00
Alessandro Ranellucci
dbcfebeb66
Rename support_material_tool to support_material_extruder
2012-06-28 15:14:27 +02:00
Alessandro Ranellucci
3e8bc73fcb
Fix typo in previous commit
2012-06-28 14:49:20 +02:00
Alessandro Ranellucci
898266fd34
Initial refactoring for supporting multiple extruders. Little speed optimization included
2012-06-28 14:44:54 +02:00
Henrik Brix Andersen
ed9f6e1f1e
Rephrase a few of the wizard instructions
2012-06-27 23:20:29 +02:00
Henrik Brix Andersen
84cfe7afc7
Automatically show configuration wizard on first run
2012-06-27 22:13:57 +02:00
Henrik Brix Andersen
7211561ab3
Change wizard welcome text a bit
2012-06-27 21:51:12 +02:00
Henrik Brix Andersen
145b9076cc
Let the wizard automatically set first_layer_height = nozzle_diameter
2012-06-27 21:03:57 +02:00
Alessandro Ranellucci
92460ba902
Bugfix: the plater didn't remember last input file directory. #485
2012-06-27 20:27:46 +02:00
Henrik Brix Andersen
dbc42f6841
Make it more clear that the wizard uses your current configuration as basis
2012-06-27 19:56:47 +02:00
Alessandro Ranellucci
eea6d84314
Bugfix: infill extrusion width was ignored
2012-06-27 19:55:54 +02:00
Alessandro Ranellucci
47a07a86ee
Bugfix: GUI was unable to update flow settings
2012-06-27 19:49:53 +02:00
Alessandro Ranellucci
96a3234eaa
Different speed for external perimeters. #488
2012-06-27 19:42:16 +02:00
Henrik Brix Andersen
52872753df
Minor changes to text and layout to look more like other wizards
2012-06-27 19:41:37 +02:00
Henrik Brix Andersen
cd48dc4031
- Add nozzle_diameter to Configuration Wizard
...
- Automatically set layer_height to (nozzle_diameter - 0.1)
2012-06-27 17:59:29 +02:00
Mark Hindess
840752194f
Speed up encloses_point calls from medial_axis code.
...
The points shouldn't be on hole borders so we can make the check
much quicker. Gives over 50% speed up slicing reprap shot glass
(thing:11944) with default settings and 0.3 layer height.
2012-06-26 23:11:46 +01:00
Henrik Brix Andersen
406e31a20d
Fix icon file name
2012-06-26 22:47:58 +02:00
Henrik Brix Andersen
373b341280
Remove cooling option from wizard
2012-06-26 22:47:10 +02:00
Henrik Brix Andersen
de3347c825
Add initial configuration wizard
2012-06-26 17:42:29 +02:00
Mark Hindess
a4de0e659d
Trivial typo/grammar.
2012-06-25 22:51:20 +01:00
Alessandro Ranellucci
3a8f4015d6
Don't reset E when the makerbot flavor is selected
2012-06-24 21:05:44 +02:00
Alessandro Ranellucci
0938c73d08
Revert "Don't reset E when the makerbot flavor is selected"
...
This reverts commit 2e5e5983be
2012-06-24 21:05:21 +02:00
Alessandro Ranellucci
2e5e5983be
Don't reset E when the makerbot flavor is selected
2012-06-24 20:58:12 +02:00
Alessandro Ranellucci
f057dd4818
Bump version number to the correct one
2012-06-24 17:21:27 +02:00
Alessandro Ranellucci
73655d7ccc
Bump version number
2012-06-24 17:18:29 +02:00
Alessandro Ranellucci
0372d06247
Releasing 0.8.4
2012-06-24 16:50:09 +02:00
Alessandro Ranellucci
a4dcbd62da
Remove recursion warning for Douglas-Peucker
2012-06-24 16:37:59 +02:00
Alessandro Ranellucci
f88f516c30
Optimize honeycomb travels
2012-06-24 16:09:24 +02:00
Alessandro Ranellucci
a6dca1d82a
New option for support material pattern spacing; also, fixes and speedups to the overhang detection
2012-06-24 14:39:35 +02:00
Henrik Brix Andersen
a861b95b12
- Change about menu item title to match UI guidelines on Mac OS X, GTK+ and MSW
...
- Lower-case Slic3r::GUI::about() to match other, custom methods
2012-06-24 12:09:48 +02:00
Henrik Brix Andersen
e024c31ce5
Use settings title to make save dialogs and tooltips more clear
2012-06-24 10:31:00 +02:00
Henrik Brix Andersen
f07ad630c4
Use tab title in close confirmation dialog
2012-06-24 10:22:44 +02:00
Henrik Brix Andersen
30d88d7ffa
Store the tab name within each tab for reuse
2012-06-24 10:20:42 +02:00
Alessandro Ranellucci
36753d85b7
New option to define the overhang threshold angle for support material generation
2012-06-23 23:54:39 +02:00
Alessandro Ranellucci
07daefeddb
Require Moo 0.091009
2012-06-23 23:28:21 +02:00
Alessandro Ranellucci
1fb44474a9
Connect support material paths
2012-06-23 22:58:12 +02:00
Alessandro Ranellucci
bf1aba3d08
New --support-material-pattern and --support-material-angle options
2012-06-23 22:43:23 +02:00
Alessandro Ranellucci
e72bd56b9d
Rename brim_thickness to brim_width
2012-06-23 22:27:59 +02:00
Alessandro Ranellucci
a9d480f7bf
Bugfix: first layer extrusion width was computed on general layer height rather than first layer height. #465
2012-06-23 21:45:18 +02:00
Alessandro Ranellucci
48addf8c3f
New feature: brim. #424
2012-06-23 21:31:29 +02:00
Alessandro Ranellucci
53d24bc580
Bugfix: some infill paths were not connected. #477
2012-06-23 20:27:28 +02:00
Alessandro Ranellucci
ac08cf7469
Disable arc compensation code
2012-06-23 20:19:58 +02:00
Alessandro Ranellucci
44c636aea1
Do not oversimplify outer perimeters and keep the full resolution of the input file. #340 #462
2012-06-23 20:08:08 +02:00
Alessandro Ranellucci
20229fccdb
Bugfix: fatal error when a layer contained nothing
2012-06-23 18:31:24 +02:00
Alessandro Ranellucci
464400a37b
Bugfix: when skirt distance was set to zero, the first loop coincided with the outer perimeter of the object
2012-06-23 17:44:05 +02:00
Alessandro Ranellucci
05e4571310
Do perimeters from outside to inside. #466
2012-06-23 17:41:44 +02:00
Henrik Brix Andersen
d0588c2ef8
Ask for confirmation before closing if there are unsaved presets.
2012-06-23 17:39:20 +02:00
Henrik Brix Andersen
1409cbf7f7
Add Slic3r::GUI::Tab::is_dirty()
2012-06-23 17:38:19 +02:00
Alessandro Ranellucci
410279823c
New separate option to control the addition of automatic extra perimeters. Also, add none if perimeters are set to 0. #459
2012-06-23 17:10:30 +02:00
Mark Hindess
f61a1f5a07
Create *::Geometry::nearest_point_index to speed up shortest_path method.
...
This fix gives a further 10% speedup on simcop2387's coaster.
2012-06-22 23:12:39 +01:00
Mark Hindess
62eb41b967
Manage flattened endpoint list rather than creating it at every iteration.
...
Gives an 8% speedup on simcop2387's coaster for me.
2012-06-22 23:12:39 +01:00
Henrik Brix Andersen
b59040f954
Rename 'Save Config' menu item to 'Export Config' to match button label.
2012-06-21 22:50:40 +02:00
Henrik Brix Andersen
60ff9938ef
- Add Slic3r::Config::get_raw() for getting the raw, uncalculated values.
...
- Use get_raw() for saving and displaying options in GUI
Forward-ported from 4031cf26b4
2012-06-21 13:28:55 +02:00
Henrik Brix Andersen
f2617bffda
Add debug information for locating a users data directory
2012-06-21 13:21:42 +02:00
Henrik Brix Andersen
c4f8c36ecc
Handle ENTER key in Slic3r::GUI::SavePresetWindow
2012-06-21 13:01:59 +02:00
Henrik Brix Andersen
f69903573a
Always enable preset save button.
2012-06-21 12:20:18 +02:00
Alessandro Ranellucci
a578af9d28
Fix support material
2012-06-21 11:51:24 +02:00
Alessandro Ranellucci
94e28b9ab8
Require Math::Clipper 1.09 because it contains important bugfixes
2012-06-21 10:53:04 +02:00
Alessandro Ranellucci
81a5267cc7
Fix widths on plater
2012-06-20 22:50:38 +02:00
Alessandro Ranellucci
ac59297e39
Fixes for Windows
2012-06-20 21:43:06 +02:00
Alessandro Ranellucci
8d465aca34
A couple fixes for GTK
2012-06-20 17:17:07 +02:00
Alessandro Ranellucci
69c3f12c60
Workaround for GTK issues
2012-06-20 17:08:38 +02:00
Alessandro Ranellucci
be8970b497
Fixed regression causing infill lines not being always connected near perimeters
2012-06-19 18:49:46 +02:00
Alessandro Ranellucci
a664709b31
Remember last presets
2012-06-19 18:11:51 +02:00
Alessandro Ranellucci
0ef8da42a6
Preset deletion
2012-06-19 17:47:48 +02:00
Alessandro Ranellucci
b910840f76
Preset shortcuts in the plater tab
2012-06-19 17:23:10 +02:00
Henrik Brix Andersen
8fcf24a766
Merge pull request #467 from henrikbrixandersen/ratio-options
...
Two small ratio option improvements/bug fixes
2012-06-19 06:44:16 -07:00
Henrik Brix Andersen
4031cf26b4
- Add Slic3r::Config::get_raw() for getting the raw, uncalculated values.
...
- Use get_raw() for saving and displaying options in GUI
2012-06-19 15:32:56 +02:00
Alessandro Ranellucci
0003c093e3
Reflect external configs in preset menus
2012-06-19 14:47:02 +02:00
Henrik Brix Andersen
8d25e6490a
Set CLI option type to 'string' for all options allowing ratio inputs
2012-06-19 11:38:12 +02:00
Henrik Brix Andersen
b7d2860d5b
Allow negating bool cli options by using '--no-foo' or '--nofoo'
2012-06-18 23:39:53 +02:00
Alessandro Ranellucci
35f36e0446
New preset management (unfinished)
2012-06-18 22:27:57 +02:00
Alessandro Ranellucci
9e6e3bd269
Custom Treebook implementation
2012-06-18 16:46:43 +02:00
Alessandro Ranellucci
e810f9b898
Moved filament settings to new Filament tab
2012-06-18 14:29:47 +02:00
Alessandro Ranellucci
20e1a9c860
Updates to the description and the README
2012-06-18 13:52:38 +02:00
Alessandro Ranellucci
2b6b91cd01
Tooltips
2012-06-18 13:49:14 +02:00
Alessandro Ranellucci
d8a64f0386
Use spin controls for integer values
2012-06-18 11:52:45 +02:00
Alessandro Ranellucci
f38f2f139e
Make window resizable
2012-06-18 11:26:21 +02:00
Alessandro Ranellucci
19a78de82f
Enlarge the Output filename format field
2012-06-18 10:28:53 +02:00
Alessandro Ranellucci
a59b82db06
Switch from wxComboBox to wxChoice
2012-06-18 10:24:17 +02:00
Alessandro Ranellucci
72298877bb
Moved units of measure to the right of input fields
2012-06-18 10:19:24 +02:00
Alessandro Ranellucci
b7983b54f8
Remove label for large text fields
2012-06-17 23:24:10 +02:00
Alessandro Ranellucci
ce9fdbc047
Icons for settings
2012-06-17 22:54:08 +02:00
Alessandro Ranellucci
21ef09c228
Group settings using Treebooks
2012-06-17 22:27:05 +02:00
Alessandro Ranellucci
48d345c189
Bugfix: first_layer_speed was accepting mm/m values rather than mm/s when expressed as absolute. #452
2012-06-17 19:42:11 +02:00
Alessandro Ranellucci
217a6f2525
Bugfix: any retraction_lift value different from "0" caused no retraction before layer changes. #453
2012-06-17 19:36:02 +02:00
Alessandro Ranellucci
7d6545dd07
Further simplification of point_in_polygon()
2012-06-17 19:09:11 +02:00
Mark Hindess
2ef565fc4d
Simplify creation of $n, @x and @y in point_in_polygon test.
...
Gives 30% speed up on simcop2387's coaster on my laptop and it cuts the
maximum resident set size too. I know this is going to be replaced but
thought this might be useful in the meantime.
2012-06-16 08:28:37 +01:00
Alessandro Ranellucci
4d2a813450
Bump version number
2012-06-14 20:26:58 +02:00
Alessandro Ranellucci
a2c0e4a674
Releasing 0.8.3
2012-06-14 19:13:04 +02:00
Alessandro Ranellucci
ca8a91b2b0
Only apply arc compensation to circular holes. #418
2012-06-14 15:06:22 +02:00
Alessandro Ranellucci
b00d960f4d
Merge pull request #450 from henrikbrixandersen/growl
...
Move Growl::GNTP handling to Slic3r::GUI
2012-06-14 05:35:25 -07:00
Henrik Brix Andersen
129f0fa904
Move Growl::GNTP handling to Slic3r::GUI to allow notifications from both Slic3r::GUI::SkeinPanel and Slic3r::GUI::Plater.
2012-06-14 13:49:50 +02:00
Nicolas Dandrimont
4296ea6da1
Slic3r::Polygon's boost_linestring method needs to close the contour.
...
This prevented Slic3r from detecting some bridge supporting edges
(basically, if that edge was the last one in the contour). This
addresses some of the bridge detection issues (#414 , #358 ).
2012-06-14 13:33:59 +02:00
Henrik Brix Andersen
3aa901f149
Show version and description in About dialog
2012-06-12 23:51:59 +02:00
Henrik Brix Andersen
65d6a83672
wxID_EXIT is already imported, no need to specify package name
2012-06-12 23:47:59 +02:00
Henrik Brix Andersen
230d4377c9
Fix display of special menu items (wxID_ABOUT, wxID_EXIT) on OS X
2012-06-12 23:46:50 +02:00
Alessandro Ranellucci
b926e0b27d
Support material lines need to be white
2012-06-11 20:42:39 +02:00
Alessandro Ranellucci
55ed4af06e
DLP support material in SVG output (untested)
2012-06-11 14:47:48 +02:00
Alessandro Ranellucci
1f35a3f6aa
Fixed regression preventing SVG export to work properly. #428
2012-06-11 13:50:38 +02:00
Alessandro Ranellucci
71c1c66985
Label and CLI option were wrong for top_solid_infill_speed. #425
2012-06-11 13:45:03 +02:00
Alessandro Ranellucci
c0c84d13b8
Always set bed temperature after first layer if first layer temperature is set. #427
2012-06-11 13:43:23 +02:00
Alessandro Ranellucci
3e94add8a8
Pass config options as environment variables to post-processing scripts
2012-06-09 17:52:03 +02:00
Alessandro Ranellucci
62bd33a766
Fixed regression causing fatal errors. #429
2012-06-09 15:53:14 +02:00
Alessandro Ranellucci
0c4b112718
Fixed regression preventing arcs to be generated at all (center detection is still buggy)
2012-06-07 19:53:27 +02:00
Alessandro Ranellucci
c0c53c4397
Fill gaps. #281
2012-06-07 15:31:51 +02:00
Alessandro Ranellucci
00c6b1bdf8
Bugfix: some thin walls still gave a fatal error. #416
2012-06-07 12:21:33 +02:00
Alessandro Ranellucci
0226039dfb
Fixed regression when cooling is enabled
2012-06-07 11:38:54 +02:00
Alessandro Ranellucci
caa32ab282
Fixed regression causing flow errors when using legacy config files. #421
2012-06-07 11:24:45 +02:00
Alessandro Ranellucci
709c444976
Fixed fatal error when using --first-layer-extrusion-width
2012-06-07 11:17:35 +02:00
Alessandro Ranellucci
5c9916dc75
Some basic ability to close holes in non-manifold models
2012-06-06 22:28:23 +02:00
Alessandro Ranellucci
85ef7ce665
Bugfix: many thin walls were not detected correctly. #313
2012-06-06 21:27:39 +02:00
Alessandro Ranellucci
fbfbfac2b6
New --top-solid-infill-speed option. Also, --solid-infill-speed and --small-perimeter-speed can be expressed as ratios too. #174 #151
2012-06-06 19:59:20 +02:00
Alessandro Ranellucci
2ccb443c2f
Bugfix: not retracting between infill of different islands using low infill densities. #242
2012-06-06 19:38:35 +02:00
Alessandro Ranellucci
58a696e666
Lift Z when changing layer too
2012-06-06 19:20:43 +02:00
Alessandro Ranellucci
8883df6692
Warn user when object couldn't be split
2012-06-06 19:00:34 +02:00
Alessandro Ranellucci
13e10abbbe
Fixed regression causing some models not to be sliced correctly. #410
2012-06-06 18:57:46 +02:00
Alessandro Ranellucci
c7af74884f
Legacy config files were not correctly supported
2012-06-06 18:47:11 +02:00
Alessandro Ranellucci
82dd3c7a3e
New --perimeters-extrusion-width and --infill-extrusion-width options. #302
2012-06-06 18:05:03 +02:00
